Manual for Verizon (Actiontec) Router

Need a better manual for the Acitontec router.  Cannot figure out how to configure it for my lan using fixed (private) I.P. addresses.   Also cannot log into router.  Password echos several dots for each character.  Is there a better manual somewhere for this router?

Manual for the Verizon version of the Actiontec is here
http://onlinehelp.verizon.net/consumer/bin/pdf/VzMI424WRUserManualv4.pdf

Similar Messages

  • My Idevices are getting an IP address that is similar to Verizon Actiontec router, however I'm using Airport is primary router? Why?

    I have my airport time capsule as primary router hooked up by ethernet from ONT from Verizon.  My Verizon Actiontec router is hooked up to APtime capsule via LAN for DVR and TV guide. It works, however my Idevices will get a different IP address 192.168.1 from time to time and not be able to access the internet.  I fix this by renewing my lease then the device goes back to the IP 10.0.0.1 like it should.  My question is why does this happen? How do I prevent it?
    Thank You in Advance.

    Hi alfredlino,
    If you are seeing 2 different ranges of IP addresses, you might be in a double NAT situation as described in this article:
    Back to My Mac: "Double NAT" configurations may prevent Back to My Mac connections
    http://support.apple.com/kb/TS1208
    Even if you are not using Back to My Mac, the article still remains valid:
    Additional Information
    How to tell if you are using "double NAT"
    While every network setup is different, here is a simple way to tell if your computer is on a "double NAT" network:
    In Finder, from the Go menu, choose Utilities.
    Open Network Utility.
    Click Traceroute.
    In the field, enter "www.mac.com".
    Click Trace.
    After starting the trace, look for the line beginning with the number 2. If the address in that line is any IP address in either of the following ranges:
    10.x.x.x
    192.168.x.x
    ... then your network has multiple layers of NAT.
    The Resolution instructions in that article should help resolve this for you.
    Cheers!
    - Ari

  • Bonjour and Verizon Actiontec router MI424WR

    The Verizon Actiontec router MI424WR does not allow Bonjour with its default settings.
    To allow Bonjour to operate, one must open the Router and select >Advanced>IGMP Proxy.  Change the setting IGMP Proxy from Enabled to Disabled, then apply the setting.
    This will allow Documents to Go to sync using WiFi, and will probably solve problems for other items that use Bonjour.

    Stevesvp is correct:  it's an Actiontec router issue.  And it's not just with Mac OS X:  the same problem happens with other devices that have nothing to do with Apple (TiVo, Samsung TVs, etc).  I'm not sure why 10.4 works, maybe it's using an older way of accessing Bonjour (the Bonjour protocol has been undergoing changes to try to address complaints from large network admins about chattiness), but it's not Apple's fault.  And this problem doesn't happen with any other router than Actiontec.
    The Disabling IGMP Proxy via the Actiontec's "Advanced -> IGMP Proxy" menu works fine and solves the problem.
    One complication is that the new Rev I of the Actiontec router removed the link to the IGMP page from the Advanced menu.  If you have that Rev, however, you can still get to the IGMP Proxy menu via a deep link discovered by user BigDaddy on DSLReports.  Just loging to your router as normal, then use this link, which will take you directly to the now-hidden IGMP Proxy config page:
    192.168.1.1/index.cgi?active_page=6059
    I can confirm that this works on my Rev I router.

  • WVC80N & Verizon Actiontec router

    Has anyone had any success setting up a WVC80N camera with a Verizon Fios Actiontec Router? The install program always fails to find the camera once it is reset and the Ethernet cable removed. At this point I don't believe their compatible.

    I was able to successfully set up my WVC80N with my Verizon Actiontec (Wireless G) router.  *However*, I noticed regular interruptions in my wireless connectivity with the hub and print jobs sent to my wireless printer stopping half way.  After a week of denial (I suspected some sort of conflict between the "N" camera and the "G" hub but ignored this suspicion) and checking everthing else I could think of, I finally powered down the camera and...it was like a MIRACLE.  Suddenly everything was running great.
    Perhaps there is a setting on the WVC80N that will allow it to play nicely with a G hub?  I have the "G" version of the same camera on my network which has been running flawlessly for a year.

  • Settings for fios actiontec router using coax when adding time capsule as ac router

    I would like to set up my new time capsule as my main wireless router on a fios coax-wan internet that is currently using the m1424wr revisiion I router. 
    What are the settings i should use for the actiontec versus the time capsule and what is the best way to set it up to take advantage of the AC wireless on the TC without losing set top box features providing by the actiontec router over coax? 
    I got the TC to conenct via WAN to LAN on actiontec but i think that may limit my ability to take advantage of the capabilities of the time capsule. 
    Any suggestions ont the best set up given I have multiple devices both iOS, OSX and need relaiable coverage of a 3 story town house. 
    Thanks!
    Tim

    Best setup is to bridge the TC.. which I think is how you set it up.
    I got the TC to conenct via WAN to LAN on actiontec but i think that may limit my ability to take advantage of the capabilities of the time capsule.
    You do miss the guest wireless network and BTMM on the TC itself... but otherwise it is the best for everything else.
    Tell us if you need these functions.
    To cover a 3 storey town house a single wireless router is not going to be adequate.. if you can place the TC on a different floor to the modem that could be very helpful, with ethernet to link the two.
    Otherwise you need an Express or two so the coverage can be extended.

  • Verizon Actiontec Router M1424WR

    How do I Login to my Verizon M1424WR Router when I get the following message:
    Login has been temporarily disabeled due to too many unsuccessful login  attempts, please try again later.
    I have been trying to login for six days and keep receiving the same message.
    Any help would be appreciated>
    Solved!
    Go to Solution.

    Guffy wrote:
    How do I Login to my Verizon M1424WR Router when I get the following message:
    Login has been temporarily disabeled due to too many unsuccessful login  attempts, please try again later.
    I have been trying to login for six days and keep receiving the same message.
    Any help would be appreciated>
    When you get the "too many login" message, further attempts to login will extend the time.  You need to stop trying until the router resets.  I believe the time frame is 24 hours, but I'm not sure on that.
    Alternatively, you can reset your router.  Push the reset button on the back and hold it for 15 seconds.  That should enable you to login.
    If you are unsure of your password, refer to above reply.

  • Port Forwarding for L2TP/IPSec VPN Behind Verizon Actiontec MI424WR-GEN2 Rev. E v20.21.0.2

    I've got a NAS setup with various services running on custom ports to help minimize exposure (especially to script kiddies). I've tested everything both internally and externally to confirm they all work, and even had someone at a remote location confirm accessibility as well.  Port forward configurations performed on the Actiontec are working well. 
    I installed an L2TP/IPSec VPN server, tested internally and it connected successfully.  So for all intents & purposes, this validates that the VPN server is correctly configured to accept inbound connections and functioning correctly.
    I logged into the Verizon Actiontec MI424WR router, setup port forwarding for UDP ports 500, 1701 & 4500.
    Note: I added the AH & ESP protocols based on what I saw on the built-in L2TP/IPSec rules
    With the port forwarding in place, I tested VPN externally but it didn't connect.
    I've done the following so far to no avail:
    Double & triple checked the port forwards, deleted & recreated the rules a few times to be sure
    There are no other pre-existing L2RP/IPSec port forward rules or otherwise conflicting port forward rules (e.g.: another rule for ports 500, 1701 or 4500)
    There was an L2TP port triggering rule enabled, that I toggled on and off with no change
    Verified the firewall on VPN server had an exclusion for L2TP, or that the firewall is off. (Firewall is off to reduce a layer of complexity, but it worked internally to begin with so I doubt that's the issue.)
    Since it works internally, and there are no entries in the logs on the device indicating inbound connections, I'm convinced its an issue with the Verizon Actiontec router.  But unfortunately, I'm not sure what else to try or where else to look to troubleshoot this.  For instance, is there a log on the router that I can view in real time (e.g.: tail) that would show me whether or not the inbound connection attempt is reaching the device, and whether or not the device allowed or blocked it?
    My router details:
    Verizon Actiontec
    MI424WR-GEN2
    Revision E
    Firmware 20.21.0.2
    Verizon Actiontec built-in L2TP/IPSec rule templates.  They're not currently in use, but are baked into the firmware for easy configuration/selection from a drop down menu.
    Solved!
    Go to Solution.

    normally a vpn on that router, will have a GRE tunneling protocol as well.
    two ways to build the PF rules,
    Manually
    Preconfigured
    I know the preconfigured VPN rules will do the GRE protocol as well, but if you do it by hand you can't get it.

  • How can I get my Cisco wireless router to wirelessly connect to my Verizon Fios Actiontec router?

    I have Verizon Fios for internet, tv and phone. The Verizon Actiontec router is connected with a ethernet cable into my desktop and the internet is up and running. Now I bought a Cisco Linksys WRT54GL Wireless-G Broadband Router, and I wanted to connect it to another desktop two floors up. I set up the Cisco router according to the instructions, but I'm not able to connect to the internet. It shows that my computer was able to get a Local Network connection, but internet connection keeps failing.... I tried changing the IP address. But I'm confused about the whole thing. Is the Default gateway number suppose to be the same for both routers? Is it possible that the Actiontec router isnt giving off a strong enough wireless signal? I'm open for suggestions! Thanks

    Mac or Windows machine?
    Is the WRT connected directly to the upstairs computer? I don't think you can use the WRT that way?
    Have you had a look here?:http://homecommunity.cisco.com/t5/Wireless-Routers/General-Linksys-Router-FAQs/td-p/4286
    I THINK you would have to have a WETxx (Ethernet Adapter)  instead?
     If it connects to the Internet even breifly then I suppose that means your connected but it may be losing the signal and failng. You would porbably have ot get a WAP(Access Point) and use it as a repeater.
     I'm a bit rusty on the names so I hope i got them right, hope it helps.....

  • How can I use two VERIZON ACTIONTEC routers with my home internet?

    Hi,
    I currently have one Verizon Actiontec router (newest model) that is connected as my primary router that handles all the internet stuff and MoCA for the TV's. It is connected via Coaxial cable into the wall on the first floor of my house. My house is 4 floors - Basement - 1st floor - 2nd floor- loft.
    Now, I have a second identical Verizon Actiontec router that I want to put into good use but not sure how. I assume the only thing I can accomplish with it is to extend the wireless network, or make it faster, etc. I'm not exactly sure.
    My house doesn't have any ethernet wall jacks, only coax. But there is a coax jack in every room on every floor.
    I do not want to drill any holes into any walls, or run long cables that go up to other levels.
    My experience with this tech is not too advanced (I know how to reset the router, go into the config page, change security, some IP stuff), but my knowledge is not technical enough to understand how to configure this manually without instructions/assistance/guidance.
    I hope I have provided enough information, if there is anything else I am missing or you need to know please inform me.
    Thank you in advance, and I appreciate any advice.
    sherorox
    Solved!
    Go to Solution.

    You can use the extra router to provide ethernet and a Wireless Access Point (WAP) anyplace you have an active coax connection.
    http://www.dslreports.com/faq/15984

  • Add Wireless N Router To Network With An Actiontec Router

    Hi everyone, I know this wireless N thing is being beaten to death but I just really need to be pointed in the right direction.  I recently built a HTPC setup with a SiliconDust HD Homerun network tuner so I could share three tuners with computers on my network.  I've got two PCs wired to the network right now which share them fine.  But the problem I'm running into is when I try to set up my laptop to watch something wirelessly, usually a game in HD.  The signal is very weak and I constantly lose the tuners because of that, not to mention the picture is very choppy.  I saw on a Microsoft Windows Media Center site that they don't recommend streaming HD TV feeds over anything other than a wireless N connection.  I currently have the standard Actiontec router that came with FiOS, and it doesn't the N band.  Now, that router accesses the internet signal through a coax so I know I can't get rid of it, but I've seen mentioned in a couple of places that you can just add a wireless N router into the network and turn off the wireless on the Actiontec router.  This is the router I was thinking of getting:
    http://www.bestbuy.com/site/Cisco+Linksys+-+E1200+Wireless-N+Router+with+4-Port+Ethernet+Switch/2225...
    My current network setup is like this: Actiontec router upstairs which carries internet to -> a gigabit switch connected to -> computer, tuners, and printer upstairs, with a line run to -> another gigabit switch downstairs which connects to -> a computer, and an XBox. 
    So a couple of questions about this:
    - Where would this go on the network?  Would it go after the router and before the switches, like I run the internet into the new router then out to the switch, or can I just add it to one of the switches?
    - Will I need to do any sort of port forwarding or anything, or assiging of IP addresses?
    - Anything else I should know or might run into?
    I love my FiOS service so hopefully this will help me get even more out of it!
    Solved!
    Go to Solution.

    I wanted to upgrade to an N protocol wireless router but since Verizon doesn’t offer the option, I purchased a Netgear N600. Unfortunately, after it arrived, I discovered that it didn’t have a coax connection as did the Verizon Actiontec. I then set out to find out how to daisy chain the routers to leave the Actiontec connected to the coax and connect the two routers via Ethernet cable. To my good fortune, during the time I spent on the phone with Netgear, I learned my way around their router interface and with the help of a co-worker that actually has a solid understanding of router/network configuration, I finally got everything working correctly – my port forwarding for RDC login worked, I could connect devices to either router and everything could once again see each other (e.g. PC, printer via Ethernet, Blu-ray player for Netflix, receiver for streaming Windows Media Player). Hopefully, this post will help you get up and running quickly and avoid the several hours I spent groping in the dark for the correct configuration.
    Login to Verizon Actiontec router (type 192.168.1.1 into browser address bar).
    No configuration changes are necessary on the Actiontec, you just need to identify an open IP address range in My Network section (I chose 192.168.1.50). This will be used as your static IP address of the Netgear router LAN settings.
    Connect you PC via Ethernet cable directly into an Ethernet port (not WAN/Internet) on the Netgear router. No other connections are needed at this point.
    Note: Do not use the Netgear wizard CD to setup the router. It will not take you through the necessary steps as you’re not setting it up as a router.
    Login to the Netgear router (type routerlogin.net into the browser address bar) using the default login of “admin” and password “password”. Depending on your firmware version, your interface may vary but hopefully you’ll be able to find the same configuration options in either but perhaps not in the same order or placement. For subsequent logins after the router is active, you may need to type the Netgear IP address (e.g. 192.168.1.50) as routerlogin.net may open a search.
    At the top of the Netgear genie, click on the Advanced tab.
    On the left side, expand Setup, then select Internet Setup.
    Select “Get dynamically from ISP”, under Internet IP Address.
    Under Domain Name Server (DNS) Address, select “Use These DNS Servers”, and enter the IP Address of your Actiontec router (e.g. 192.168.1.1) in the Primary DNS” field.
    Next go down a few options  within Setup to Wireless Setup.
    In the Wireless Network 2.4GHz section, click Enable SSID broadcast.
    Enter a meaningful name in “Name (SSID)” as this is what will be displayed for your wireless connection.
    For Channel, select Auto.
    For Mode, select “Up to 300 Mbps”.
    Security Options, recommend WPK2-PSK[AES] for longer/stronger password options.
    Set the password of your choice.
    Repeat the same process for Wireless Network 5GHz, except vary the name slightly so you’ll be able to distinguish which band you’ll connect to. You can optionally use the same or different password as your 2.4GHz. The only exception is you’ll have to select a Channel of your choice.
    Next go down a couple more options within Setup to the LAN Setup.
    In the LAN TCP/IP Setup section, enter the IP Address you chose in step 2 (e.g. 192.168.1.50).
    Enter the IP Subnet Mask 255.255.255.0
    Leave the block for “Use Router as DHCP Server” blank as your IP assignment will be handled by your Actiontec router.
    You’re now finished with the configuration and you can connect the Actiontec router to the Netgear router using an Ethernet cable using the LAN ports (Note: do not connect the two routers using the WAN/Internet ports on either). You may connect your devices (PC, printers, A/V devices, etc.) to either router. If you have devices that are gigabit capable, you’ll want to connect them to the Netgear router to take advantage of the higher speed.
    To avoid any possible interference between the 2.4GHz range of the two routers, you can optionally turn off the Actiontec wireless capability by logging into the Actiontec router admin (described above), go to the My Router tab, and there should be an option for “Change Wireless Settings” in the Quick Links section. Option 1 allows you to turn On/Off the wireless portion of the router.

  • Verizon Fios router in front of 2 Linksys routers

    I have had Verizon Fios for about two years and my configuration was a WRT300N V1 connected to Fios, which was setup for DHCP reservations, and a WRT54GS V2 connected LAN-2-LAN to the WRT300N. Everything worked fine.
    I just upgraded to Fios TV and was told that a Verizon router (an Actiontec I think) has to now be connected to Fios since the tv boxes connect to the router. Just to quickly get it working I changed the WRT300N to LAN mode (disabled DHCP and NAT) and plugged it into the Verizon LAN port. This worked for the hardwired and wireless devices directly connected to the WRT300N. However the hardwired devices connected to the WRT54GS cannot connect to the internet but wireless devices connected to the WRT54GS can. Curiously, anyone know why this would be the case?
    What I really want to do is setup the WRT300N and WRT54GS as I originally did, where the WRT300N would do DHCP reservations. From looking on this site it appears I need to change the WRT300N to a 192.168.2.1 (currently is 192.168.1.3) so that it is a separate network and connect the WAN port on the WRT300N to a LAN port on the Verizon router. I attempted this and it did not appear to work (could not access the internet) and I was wondering if someone could tell me that what I am looking to do can be done and how to set it up. Thanks in advance Jay
    Message Edited by j24 on 05-20-2008 10:23 PM
    Message Edited by j24 on 05-20-2008 10:23 PM
    Message Edited by j24 on 05-20-2008 10:24 PM

    Actually I wanted to connect the WAN port of the WRT300N to a LAN port of the Actiontec Verizon router, and connect the WRT54GS to the WRT300N from LAN-to-LAN.
    I read the instructions on cascading routers, which is what I wanted to do between the WRT300N and Actiontec. I set everything up and it initially did not work (and as a result I started this thread). I then realized that the firmware on the WRT300N and WRT54GS were not the latest versions so I updated the firmware and everything worked!
    So the WRT54GS now has an ip of 192.168.5.101, has DHCP disabled and is connected from a LAN port to a LAN port on the WRT300N. The WRT300N now has an ip of 192.168.5.100, has DHCP enabled, has DHCP Reservations being used (as was before and is the reason I wanted to keep that part of the network the same) and is connected from the WAN port to the LAN port of the Verizon Actiontec router. The Verizon router is still on the 192.168.1 address. I guess I should have looked at the firmware first.
    Thanks for the reply
    Jay

  • Can You Daisy Chain Verizon Actiontec MI424WR Routers???

    I currently have an Actiontec MI424WR router which is a wireless G router.  Since I have some Tivo HD units in the house (they use wireless G)  that I'm looking to upgrade to Tivo Premiere (they use wireless N), I'd like to upgrade my wireless network to wireless N (I would be able to transfer HD shows between Tivo units ALOT faster over a wireless N network as the G network I have now is very slow).  I also will be buying my son an Xbox and the faster network would help with all the online gaming.
    Since Verizon doesn't yet offer a wireless N router, I'm trying to come up with a solution and I think I might have one.
    I'm sort of a newbie with networking but here is what I'm looking to do:
    I'd want to buy a second router that has wireless N capabilities (I'm looking at the Netgear WNDR3700 Rangemax Dual Band Wireless N).  Then I will go into the Verizon Actiontec router and turn off the wireless function.  Next I will connect the new router to my PC and turn on the wireless function, disable the DHCP and assing the new router a different IP address.  Then I will connect the two routers using an ethernet cable from the Actiontec LAN port the the Netgear's LAN port.  Essentially, what I want to do is have the Actiontec router still bring in all the information in from the ONT but have the Netgear router send it out via it's wireless N signal.
    I think in theory this should work but I wanted to pass it by the forum to see what details I'm missing here.  Any assistance would be greatly appreciated, including any details as I quickly glossed over my idea in the paragraph above.

    Your options are to either buy a Wireless N router, DISABLE DHCP on it, and then plug them together (the internal / ethernet side, do NOT use the WAN port on the new router in this scenario.)  That would make you effectively use it as a wireless access point instead of a router.  You do not want to get into daisy chaining routers, it'd doable, but not a complication  you need in your scenario.
    Honestly if I were you I'd just get a wireless N access point.  http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=4468240&CatId=372

  • Help setting up Actiontec router for 3G Microcell

    I have read through numerous forums here and elsewhere, all to no avail. I simply cannot get my 3G Microcell to connect. I have 4 green lights and the nonstop blinking 3G indicator. I've tried restoring default settings, numerous restarts of equipment, DMZ settings, port forwarding...nothing works. And calls to Att and verizon are nothing but a goat rope.I have FIOS 50/25 Internet with the Actiontec router.
    It's is extremely frustrating, this shouldn't be so difficult, so I'm truly hoping there's someone out there with a concrete answer for this. Any help or advice would be most appreciated!

    Gigatel wrote:
    I have read through numerous forums here and elsewhere, all to no avail. I simply cannot get my 3G Microcell to connect. I have 4 green lights and the nonstop blinking 3G indicator. I've tried restoring default settings, numerous restarts of equipment, DMZ settings, port forwarding...nothing works. And calls to Att and verizon are nothing but a goat rope.I have FIOS 50/25 Internet with the Actiontec router.
    It's is extremely frustrating, this shouldn't be so difficult, so I'm truly hoping there's someone out there with a concrete answer for this. Any help or advice would be most appreciated!
    FWIW, I am using an Actiontec router and an AT&T Microcell, both in default configuration, and I have no problem activating the Microcell.
    If viafax999's ideas don't solve your issue, you might try posting your problem on the AT&T MicroCell forum:
    https://forums.att.com/t5/3G-MicroCell/bd-p/3gmicrocell
    There will likely be more users with experience specific to the MicroCell and it's potential problems there.

  • Verizon FIOS router Actiontec MI424WR not working with bonjour printing

    Running OS X ver 10.9.3. Have a HPLaserJetP1102w. Just upgraded my Verizon FIOS router to Actiontec MI424WR Rev. I. Now my Mac can no longer find the printer wirelessly (it does, however, work thru USB). I see others have had this problem- and apparently some have solved it by changing settings on the router- but those settings options do not appear under 'advanced' for me. Verizon technical support, including the version one must pay for- was totally and utterly unable to help. Any suggestions for how to rescue this? Was all working perfectly with older Verizon router.

    >It's amazing to me that talkting to 4 or 5 Verizon Tech's, they all say "This is new to me,  I've never heard of this."  Ugh...
    I've had EXACTLY the same experience. Phone support and the techs who come to my home apparently have no idea this has been happening for months and months. Clearly, this issue hasn't filtered down from the network engineers to support.

  • Actiontec router for a Netgear n300

    Anyone have a revision F Actiontec router they are not using or need a different router now? I have a Netgear N300 that was hardly used and need an actiontec  revison f to use as an access point that I am willing to swap for. I live in Suffolk County, Long island.

    Actually it's not proprietary to Apple, it's known as WDS
    You are confusing an older technology which operated only at "g" wireless speeds along with a tremendous bandwidth penalty for each remote or relay on the network.
    WDS was never adopted as an official standard, but there are a handful of devices from other manufacturers....all at least 5-6 years old at this point.....that were usually compatible with Apple's WDS implementation. I can get you the list if you are interested.
    What I was talking about was Apple's newer "extend a wireless network" setting or feature....not WDS.
    Even if you find a compatible device and you want to use WDS on a newer Apple router, the maximum speed on the router will drop down to "g" wireless levels as soon as you configure the router.
    I don't understand why anyone would buy a newer "n" router with 5 GHz capability and then drop it down to a "g" wireless device, but we get questions all the time from users who seem to want to do this.

Maybe you are looking for