Missing key in OCR, can't set interfaces with oifcfg

(also posted in Metalink Unix Installation/OS: RDBMS Technical Forum)
I have installed clusterware on a 2 node cluster running RedHat 5.
OCR and voting disks are on raw devices, but everthing else is shared using GFS.
I can start both nodes but I can't seem to add interfaces through oifcfg.
In fact the SYSTEM.css.interfaces key does not exist in my OCR.
I applied fixs in Oracle MetaLink Note #414163.1, but when I try to do oifcfg to set my interfaces
I get a "registry key does not exist" error.
[root@ora2 bin]# ./oifcfg setif -global eth0/128.159.132.0:public eth2/172.16.5.0:cluster_interconnect
PROC-4: The cluster registry key to be operated on does not exist.
PRIF-11: cluster registry error
[root@ora2 bin]# ./oifcfg iflist
eth2 172.16.5.0
eth0 128.159.132.0
Checking the oifcfg.log I could see it was trying to update key SYSTEM.css.interfaces
2008-02-05 17:36:12.504: [ default][2897118400]OCR api procr_open_key failed for key SYSTEM.css.interfaces
I did a dump of my OCR and confirmed that this key does not exist.
I even tried regenerating my OCR with ./clscfg -install. The new one is exactly the same as the old
just different time stamps.
So now I am stuck. vipca won't run until the interfaces are defined and oifcfg won't them
because the OCR is missing a key. Does anyone know how to create this key in the OCR?
Does it need to be there?
I have thought reinstalling from scratch but I do not think anything will change as the only
thing that creates the OCR is clscfg -install in the rootconfig script.

in the $CRS_HOME/install/rootconfig, some people comment out a section that Fails. Specifically this section.
if $CH/bin/ocrconfig -upgrade $CRS_ORACLE_OWNER $CRS_DBA_GROUP;
then
$ECHO "Oracle Cluster Registry configuration upgraded successfully"
else
$ECHO "Failed to upgrade Oracle Cluster Registry configuration"
exit 1
fi
DO NOT COMMENT IT OUT.
$CH/bin/ocrconfig -upgrade $CRS_ORACLE_OWNER $CRS_DBA_GROUP is what writes these keys. People get the failed error when it fails the root.sh and decide to comment it out. Everything looks like it completes, but thiis key is not there. Instead, get the patch below which replaces the clsfmt.bin on all nodes. Uncomment the code in your rootconfig and that should fix you up. Good Luck!
PATCH 4679769 has the fixed clsfmt.bin
Also, check the permissions on your disks! Sometimes that causes it to fail as well.
Also, if on RHEL5, you will need to do the unset on LD_ASSUME_KERNEL in the vipca and srvctl files under $CRS_HOME/bin (which is fixed in 10.2.0.4 so no uncommenting needed)
Edited by: troach on Oct 6, 2009 6:49 PM

Similar Messages

  • When I highlight objects, I'm able to move them with the arrow key but I can't drag them with my mouse.

    When I highlight objects, I'm able to move them with the arrow key but I can't drag them with my mouse.

    Without system info and other details like e.g. your settings for bounding box display nobody can tell you much.
    Mylenium

  • How i can integrate RUEI interface with AM pack for Siebel

    how i can integrate RUEI interface with AM pack for Siebel for end to end monitoring

    You may want to check the Configuration > General > Advanced Settings > Clickout Settings in order to configure clickouts from RUEI to EM AMP for Siebel. Once setup you can use the Siebel Diagnostics cube to initiate clickouts with the Right mouse button.
    Please check the latest documentation for your RUEI version on http://www.oracle.com/technetwork/documentation/realuserei-091455.html?ssSourceSiteId=otncn
    Kind regards,
    Stefan Thieme
    Consultant - System Application Management
    Oracle Germany BV & Co KG
    DACH Tech Consulting
    Data Management

  • Can DAQ 6025E Interface with a digital multimeter?

    Hi,
    Can DAQ 6025E Interface with a digital multimeter? I have an ordinary digital multimeter without RS232, GPIB etc. Is it possible to read any instrument with a digital display with a DAQ 6025E card?

    NO! You have no physical connection between the dmm and the pc. The digital display on the dmm cannot just be magically transmitted between the two. The 6025 can measure voltage. It is not a camera that can read the dmm's front panel. The 6025 sits inside the pc. There is a communication bus between the 6025 and the pc. NI-DAQ/LabVIEW software allows you to control the daq board and measure voltages physically present at the input pins of the daq board. Use the daq board and throw away the dmm or throw away the daq board and buy a dmm with a serial or gpib interface.

  • Can't set keybinding with ctrl key ?

    I use compiz in lxsession. If I set compiz commands and assign ctrl key it resets back to something without ctrl and also If I set guake to ctrl+alt+space I get keybinding error. For example.
    I want to set ctrl+alt+del to lxde-logout. As I set the key combination in ccsm and press back to come to ccsm main window the command sets to alt+del. I tried with tilda as well but to no avail. What should I do ?

    I've had similar problems with compiz. I'm not sure if it can do this at all.

  • Can you set Mail with 'outgoing only' addresses?

    I run my own mail server that collects all my incoming emails, but have many addresses to send from. On ahem Outlook, I could stop accounts from collecting mail, and set them to send mail only.
    Is there a way to set Mail to have 'send-only' email accounts?

    It does only sync over wi-fi!

  • Can I set "open with" for files - associate file types with a 3rd party app

    I have PDF file attachments inside my OmniFocus application. When I double-tap them, they get opened in the standard Apple PDF viewer. But I have a better 3rd-party app which opens PDFs and allows me to edit them (mark them up) - I'd like the attachments to open in this app instead of the normal PDF viewer. I don't want to have to switch to the 3rd party app to open it - it's important to me that I can place comments on many, many PDFs inside of OmniFocus. So:
    1) is it possible to ask the iPad to have all PDFs to open in this 3rd party app?
    2) if not, is it possible to name the attachments some other extension (e.g., .xyz) and tell it to open all .xyz files with the 3rd-party PDF viewer?
    thanks in advance,
    Mike

    Michael Levin wrote:
    just out of curiosity: how did you see this without buying the app - is there some general way to get a trial from the App Store?
    When You view the features of the app in the app store, there are pictures of some of the different screens under the main description of the app. I swiped through the pictures and the fourth photo shows a screen - An image in the black box pointing to the image name - roots.jpg. In the window to the right - it says -Action - at the top - in the grey border. I wouldn't have known that the arrow didn't give the same functionality as it does when you open the PDF in Mail. But I was able to see the trash can, the curved arrow and the blue done button on the right. I never heard of the app until we started to posting. Unless the app specifies that there is a free trial period, there is no way that I know to try an app for free.
    The thing that I find odd is that you say the arrow is greyed out making that feature unavailable. That arrow icon on the iPad in Safari or Mail is what directs you to the options for - open in, print, email, etc features on the iPad. I assume that arrow must have some functionality somewhere in the app. Not sure why it is greyed out. But I stress, I know nothing about the features of the app or what it is designed to do.
    Message was edited by: Demo

  • Can I set my screen view to zoom out (ie to 90%) permanently, so that after shutdown it remembers the settings for all pages whenever opened (until I change it again) ?

    On internet explorer I can set the 'zoom' to 90% and all subsequent internet pages, tabs, windows display at this setting even after shutdown/reboot etc. It is a permanaent setting until I change it. I need this for my eyesight (long-sighted). Can I set this with Firefox?

    If you need to adjust the font size on websites then look at:
    * Default FullZoom Level - https://addons.mozilla.org/firefox/addon/6965
    * NoSquint - https://addons.mozilla.org/firefox/addon/2592

  • Warner/superior electric's SS2000PCi motion controller interfacing with LabVIEW 6i

    Sir,
    In our application, we are controlling the movement of X-Y arm on the X-Y table. For this we are using superior electric products:
    (a) Slo-Syn SS2000PCi Programmable Step Motor Controller
    (b) MD808 Motor Drive
    We are using two such controllers and motor drives to drive two 2 Amps Sanyo Denki Stepper motors: one each along X-axis and Y-axis. Along with the arm movement a data acquisition also has to be carried out. So, the motion control and Data Acquisition has to be synchronized by means of software. The problem now is to program the controller. Though MCPI Version 4.41 is there, we want to program the controller in LabVIEW 6i so that we can synch
    ronize both motion control and Data Acquisition.There is no driver which is compatible to LabVIEW 6i.
    Is there any 32-bit DLLs for this controller? If any one has these dll's please let me know. My E-mail ID: [email protected]
    So that i can call these DLLs in LabVIEW 6i and program it.Or else send me at least the detailed low level command sets of the controller in pdf format so that i can develop our own drivers.
    Regards,
    Nagendra

    Nagendra,
    Unfortunately, I was unable to find any helpful resources for you based on a cursory web search. I recommend that you contact the manufacturer of the hardware and ask them if they have a driver (DLL) that you can use to interface with LabVIEW.
    Good luck with your application, and have a good day.
    Sincerely,
    Darren N.
    NI Applications Engineer
    Darren Nattinger, CLA
    LabVIEW Artisan and Nugget Penman

  • Can someone help me with this 201435 Error during Signal Express signal generating?

    I built this signal generation tast to generate a voltage waveform. The wave form is loaded from a lvm file. (as shown in attachment pic). The waveform can be correctly viewed in preview window, so i suppose nothing wrong with the file. but when i clkick the run button, error 201435 pops up, tell me "no samples provided to DAQmx Write to initialize buffered generation".
    i dont know what step do i missed in this task. can anyone help me with this problem?

    the attachment picture
    Attachments:
    task.PNG ‏9 KB

  • Setting Actions with multimedia tool

    Anyone know where the documentation is on the video file types you can and can not set actions with when
    embedding and when streaming from a url in Pro 9 or Pro Extended 9?
    Thanks,
    sentient.usa

    Yes, putting a script that submits the form in the WillPrint action is sufficient - got it working after I found the JS for Acrobat API Reference. I haven't actually used Post before and I think I misread something when doing some research that gave me the wrong idea.
    Thanks.

  • Using Suri asking any localised question in the UK, it responds with 'cannot help' can only use US locations etc. and in US English. Have I missed something or set something up incorrectly? I also thought it would interface with your Facebook but it just

    Using Suri asking any localised question in the UK, it responds with 'cannot help' can only use US locations etc. and in US English. Have I missed something or set something up incorrectly? I also thought it would interface with your Facebook but it just comes back with a 'I can't help you with Facebook' message

    Yeah, Siri - a headline feature on the iPhone 4s page - is beta at the mo.
    But then anyone who's used Macs for a few years will know that most new software is pretty much still in beta when it's released anyway. Only Apple could get away with it and retain customers

  • Can't set the correct key when converting imported audio to GB loops

    Hi,
    I feel I am really out of options for this one. I am trying to convert a couple of mp3 files to useful GarageBand loops. This is what I tried first:
    1) drag the mp3 file on the timeline.
    2) using a steady 4-beat, match the BPM settings to that it fits the tempo of the imported file
    3) check the key of the imported file with a software instrument, and switch the project's key accordingly
    4) Edit -> Add to Loop Library
    Using this method, the produced loops show up in the Loops Browser correctly, but they play back in the wrong key. Example: I created a loop from a mp3 file that was originally played in A. I tagged it as being in the "A" key by creating a loop from it, with the project key set to "A".
    When it then shows up in the Loop Browser, and I would select this loop with my Garageband project (still) set to "A" - I would expect to hear the loop being played in its original key.
    It doesn't. It plays about four or five semitones too high (the difference between A and C, or C and E)
    I haven't been able yet to figure out why this is so, or if there is any pattern in how much the key is off.
    Then I searched far & wide, and found the Apple Loop Utility and a couple of articles on bulletsandbones.com. I also checked the midi import settings, though I doubt whether they have any influence here. They were set at 44.1 KHz.
    This is what I tried then:
    1) use bulletsandbones.com's never-fail conversion to AIF format (44.1 KHz sample rate, 16 bit)
    2) use the Apple Loop Utility to "tag" the AIF file, setting it so that it shows up in the right category of the loop browser, etc.
    3) also, use this utility to tag it with the key that the loop is played in
    4) copy the AIF file into the Loop Library directory
    5) start Garageband, and refresh / re-index the Loop Library so that the new loop is added and properly indexed
    This made no difference. Or maybe it did, but the loops thus produced STILL do not play back in the key that I tagged them in (if I set the project accordingly, of course). It's completely mystifying.
    I can omit a key indicator in the Apple Loop Utility, and only then does the loop play back as it should. But then it does not change with the project's key settings anymore.
    Even more strange: even a loop that I tagged (in the "A" key) and saved with the Apple Loop Utility, plays back too high in that same Apple Loop Utility when I re-open it. It does play back correctly in Finder's Fast Preview.
    I could not find any mention of this problem elsewhere. Does anyone have a suggestion what might cause this?

    I think this is the culprit:
    3) check the key of the imported file with a software instrument, and switch the project's key accordingly
    If the "follow tempo & pitch" box is checked, this might change the sample's pitch and throw GB off.
    Try to determine the sample's key before you import it, set the GB project's key accordingly, and then import the sample. That should assign it the correct key!

  • I have an iTunes account set up long ago on my home pc. My pc at home is antiquated and I can't interface with my account to edit acc. Info. Now I have other devices, iPhone 4 and iPad. I need to reset email apple Id and pw from iPad. How?

    I have an iTunes account set up long ago on my home pc. My pc at home is antiquated and I can't interface with my account to edit acc. Info. Now I have other devices, iPhone 4 and iPad. I need to reset email apple Id and pw from iPad. How? Should I just create new account? Don't want to lose 1500 songs.

    Hey Frankgates!
    I have an article here that can tell you how to do this:
    Apple ID: If you forget your password
    http://support.apple.com/kb/HT5787
    Thanks for coming to the Apple Support Communities!
    Regards,
    Braden

  • How can I set a unique macro for the function keys on my wireless keyboard?

    I'd like to use the F5 key as a quick stroke key for a sentence I use commonly - how can I set that up?

    <http://www.keyboardmaestro.com>

Maybe you are looking for