More wrvs4400n issues

I honestly don't understand how cisco can release a product like this. It's soo flakey and unrealiable. So far in order to get my 4400nv1 running I've had to use the recovery utility just to load firmware onto it (that was a 16hour ordeal!!) then it takes 2 tries (with regularity) to upgrade to the next level of firmware. All this just to get the device stable enough to support a wireless connection. I still have not been able to get it on the internet with any acceptable level of performance.
So far the best I can get this router to do is have 50% packet loss on the the WAN interface. I've tried disabling the DMZ, IPS, WAN access but alwaly I have 50% packet loss. These devices should be recalled.!!! my 5 year old Netgeat MR814 works better than this. this devices just has me frustrated. I work regularely with Fortinet products and they are much better and more reliable. the only reason I'm trying this out is It was given to me.
does anyone have a fix for 50% packet loss on these things! This is just stupid!

Same feelings
Great User Interface indeed-horrible with reliability. Conigured with same sattings as replaced v.1 and can't stay connected for more than an Hour. Not a defective unit though-programmed 2 others same way and very same results-wireless drops almost immidiately, then can't access Router config and after few hours complete restart-nothing works.
Using wireless on Channel free of interference, besides that 4 IPSec tunnels-those stay alive until the end.
Regards
Voytek

Similar Messages

Load More Messages issues

I saw some posts about load more messages issues, but nothing seems to be the same as my problem. I'm new to iPhone, so I must be missing something obvious.
I was looking at my emails this morning and deleted all but 5. I responded to an email, but didn’t send because I forget change the server port for outgoing mail that our server requires. So I went into settings and changed the port. I went back to my inbox but can no longer see the messages I saved, instead there's an option that says “Load More Messages” with a note below it stating “5 messages total, 0 unread”. I have no other emails in my inbox. When I click Load More Messages, nothing happens. I can’t figure out how to get to those emails. I tried cycling the power on the iphone, that didn’t help.
I'm getting new messages normally. My mail is set to show 25 recent messages. Even if I change this, it still displays the "Load More Messages". As an extreme test, I set it to show 200 recent messages, went back to my inbox, hit the "Load More Messages" option, but that didn't help. What's more, I have a full signal and I'm running 3G.

Hey man, your problem sounds similar to the one I'm having. I can't load more messages on both of my email accounts. But I think I might have figured out the problem. I recently re-installed my hotmail account and when I was looking through my,"Unread" inbox the, "Load more messages" command was working just fine. So I was continuing to go through my messages to make them read (because if your like me, I don't like to have any messages, "Unread." So when all my messages were read there was about 80 in total, and my setting was set to show the 25 most recent. So I backed out of the mail app, did a few more things and came back hoping that there would only be 25 showing with 0 unread and the ability to load more if i wished. Well, there was 25 showing but the box with the load more messages command was gone and no matter how many times I tried to refresh it would not come back.
So my theory is this; there always has to be an unread message in your inbox for the load more messages to work. Sorry about the long post. I'm going to test this theory out, knowing my luck, it won't work at all. Good luck bro!
Peace.

Return delivery more than issued quantity

Hi,
I posted the goods issuance quantity 10 with mvt 201, when return delivery with mvt 202 then system allow to post more than issued quantity.
is there any restriction or standard error message to control this.
Regards,
Ali

Hi
Are you not cancelling the document with reference to the original document. In this system will not allow you to change the quantity.
Also, refer to enhancement MBCF0005
and BADI: MB_QUAN_CHECK_BADI
Thanks
Sachin

QuickVPN timeout to WRVS4400N issue

I am using QuickVPN (1.4.1.2) on Win7 Pro, connecting to a WRVS4400Nv2 running the latest firmware (2.0.1.3). After an extended time of usage (approx 45-60min - per the log below), the tunnel drops (The remote gateway is not responding. Do you want to wait?).
I can immediately remote into my router for configuration. I can use RDP over a port forwarded rule. But I cannot re-establish the tunnel under the same ID, or even a different ID. The router is unresponsive to QuickVPN for approximately 5-10 minutes - even though it accepts the other processes fine, and routes to the internet fine for office users, and protects against external attacks.
The QuickVPN LOG looks like this:
2011/06/07 10:44:14 [STATUS]OS Version: Windows 7
2011/06/07 10:44:14 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/06/07 10:44:14 [STATUS]Windows Firewall Private Profile Settings: ON
2011/06/07 10:44:14 [STATUS]Windows Firewall Private Profile Settings: ON
2011/06/07 10:44:16 [STATUS]One network interface detected with IP address 192.168.2.46
2011/06/07 10:44:16 [STATUS]Connecting...
2011/06/07 10:44:16 [DEBUG]Input VPN Server Address = xxx.xxx.xxx                                           <---- address purposefully removed
2011/06/07 10:44:17 [STATUS]Connecting to remote gateway with IP address: xxx.xxx.xxx.xxx   <---- address purposefully removed
2011/06/07 10:44:20 [STATUS]Remote gateway was reached by https ...
2011/06/07 10:44:20 [STATUS]Provisioning...
2011/06/07 10:44:32 [STATUS]Success to connect.
2011/06/07 10:44:32 [STATUS]Tunnel is configured. Ping test is about to start.
2011/06/07 10:44:32 [STATUS]Verifying Network...
2011/06/07 10:44:38 [WARNING]Failed to ping remote VPN Router!
2011/06/07 11:43:24 [WARNING]Failed to ping remote VPN Router!                                              <---- Here is where you can see the drop 1 hr later
2011/06/07 11:43:27 [WARNING]Failed to ping remote VPN Router!
2011/06/07 11:43:30 [WARNING]Failed to ping remote VPN Router!
2011/06/07 11:43:33 [WARNING]Failed to ping remote VPN Router!
2011/06/07 11:43:36 [WARNING]Failed to ping remote VPN Router!
2011/06/07 11:43:39 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
After 5-10 minutes, I can reconnect to the router, for another 45-60 minutes, before I get booted again. I thought is was firmware, since this latest firmware addresses some specific QuickVPN issues, but it has not been resolved. Does anyone have a suggested solution for the issue?

I have very similar situation with ckunkel.
I set up WRVS4400n router and VPN settings, I can connect my outside PC to router with QuickVPN client, but after serveral times of connection or some duration of connection, router stops accepting any more VPN connection.
Only different point, I can't resolve this situation except rebooting router. Once I get router's VPN hung-up, I can't connect VPN any more without rebooting.
Router's firmware is V2.0.2.1, and QuickVPN is Ver 1.4.2.1.
This situation is veri inconvenient for our office, because once somebody outside of office starts faied VPN connection, all other staffs in office have to stop using internet, and have to wait rebooting router.
Does anyone in Cisco recognize this problem and know how to resolve this?
Yukari Mihashi
A Solutions Seattle, Inc.

N8 Belle more of issue than fun

I am using Belle for more than a month now and came up with these issue.
1. when i am using foursquare app with mobile data just connected, it hangs the device.
2. Once I disconnect from a Wi-Fi network, after a second or so all the icons reinitialize for all the screens.
3. Using app stop to kill all the apps excluding clock sometimes hangs the device.
Due to these issues i have to restart the device once a day to keep it working properly and which is very annoying. Are these normal issue with Belle or something terribly wrong with the device.
Thanks.
If I have helped at all, a click on the White Star is always appreciated. You can also help others by marking 'accept as solution'.

Also i found concerns in the existing camera with worked great with Anna update. I have default camera then camerapro and cameralover.
4. When using camerapro with 'single' AF it shows red box for initial 2-3 tries and then focus correctly.
5. The quality of autofocus for default camera has also decreased and gives blured snaps.
Not sure anyone facing the same issues, but these are major applications and feature for N8.
And if they perform like this then it is a pain.
If I have helped at all, a click on the White Star is always appreciated. You can also help others by marking 'accept as solution'.

More Major Issues with ZFS + Dedup

I'm having more problems - this time, very, very serious ones, with ZFS and deduplication. Deduplication is basically making my iSCSI targets completely inaccessible to the clients trying to access them over COMSTAR. I have two commands right now that are completely hung:
1) zfs destroy pool/volume
2) zfs set dedup=off pool
The first command I started four hours ago, and it has barely removed 10G of the 50G that were allocated to that volume. It also seems to periodically cause the ZFS system to stop responding to any other I/O requests, which in turn causes major issues on my iSCSI clients. I cannot kill or pause the destroy command, and I've tried renicing it, to no avail. If anyone has any hints or suggestions on what I can do to overcome this issue, I'd very much appreciate that. I'm open to suggestions that will kill the destroy command, or will at least reprioritize it such that other I/O requests have precedence over this destroy command.
Thanks,
Nick

To add some more detail, I've been review iostat and zpool iostat for a couple of hours, and am seeing some very, very strange behavior. There seem to be three distinct patterns going on here.
The first is extremely heavy writes. Using zpool iostat, I see write bandwidth in the 15MB/s range sustained for a few minutes. I'm guessing this is when ZFS is allowing normal access to volumes and when it is actually removing some of the data for the volume I tried to destroy. This only lasts for two to three minutes at a time before progressing to the next pattern.
The second pattern is categorized by heavy, heavy read access - several thousand read operations per second, and several MB/s bandwidth. This also lasts for five or ten minutes before proceeding to the third pattern. During this time there is very little, if any write activity.
The third and final pattern is categorized by absolutely no write activity (0s in both the write ops/sec and the write bandwidth columns, and very, very small read activity. By small ready activity, I mean 100-200 read ops per second, and 100-200K read bandwidth per second. This lasts for 30 to 40 minutes, and then the patter proceeds back to the first one.
I have no idea what to make of this, and I'm out of my league in terms of ZFS tools to figure out what's going on. This is extremely frustrating because all of my iSCSI clients are essentially dead right now - this destroy command has completely taken over my ZFS storage, and it seems like all I can do is sit and wait for it to finish, which, as this rate, will be another 12 hours.
Also, during this time, if I look at the plain iostat command, I see that the read ops for the physical disk and the actv are within normal ranges, as are asvc_t and %w. %b, however is pegged at 99-100%.
Edited by: Nick on Jan 4, 2011 10:57 AM

Network printing, more driver issues

A simple HP990 connected to an IP print server is a disaster under OS X.
1) HP provides drivers that work wonderfully - as long as it's USB (wired)
2) HP drivers dissapear if ADD PRINTER cannot physically find printer during install
3) GIMP drivers are latest - and they are almost 2 years old
4) No 2-way comm w/printer - this is NOT an IP issue
5) Dozens of printer features are unavailable to OS - show ink etc
6) Duplexing is just plain broken
7) Although HP drivers are installed, they will NOT be available to you if printer is not connected via a WIRE. This is rediculous.
8) IP "Find Printer" does not work. Cannot even find Linux printers, much less Windows, netBeui, or Wireless printers.
9) If you force printer model, you cannot use proper HP drivers. Must use GIMP.
10) Once printer is installed/configured, you CANNOT change ports. Again this is redic.
I was told OS X was VERY problematic with printing. It's the achilles heel in an otherwise wonderful OS environment.
Come on, Apple. Fire the printer guy over there and get this stuff straight.

THe HP deskjet driver does not support printing to a DeskJet 990 connected to a generic TCP/IP print server.
In Mac OS X 10.0 and 10.1 the printer drivers had to enumerate the communication protocols that they supported. This requirement was removed in 10.2 but many of the printer manufacturers still provide drivers that are tied to specific protocols. The HP provided DeskJet 990 driver support USB and AppleTalk. It may also support printing over TCP/IP to an HP JetDirect server but I've never tried that.
The Gimp-Print drivers are written so that they are independent of the communications protocol used. The Gimp-Print drivers will work over USB, Bluetooth, LPD, IPP, AppleTalk, socket, SMB, and other protocols. The Gimp-Print project is very active. It is currently closing on the release of version 5. The project has been renamed Gutenprint. You can find more information here: http://gimp-print.sourceforge.net/
1. HP drivers work over USB and over TCP/IP depending upon the printer model. For example the Photosmart 2510 driver works great over a wireless connection using TCP/IP to that printer.
2. I'm not sure what is being described in this bullet item.
3. The latest version of Gimp-Print is v5.0rc2. As noted above the project is now called Gutenprint.
4. The HP drivers support bidirectional communication. The Gimp-Print drivers do not support bidirectional communications yet but they will likely do so soon.
5. Some drivers support low ink detection and some do not. The drivers that do support low ink detection show it in the print dialog and in the desktop printer. Most drivers also come with Utilities for checking ink levels and these are linked to by the desktop printer.
6. Duplexing works fine using the HP drivers. Are you having a problem with duplex and the Gimp-Print driver?
7. As discussed above the HP drivers can not be hooked to a communications protocol they do not explicitly support. This has nothing to do with wired versus wireless.
8. The Add printer browser shows locally attached printers, AppleTalk printers, Bonjour TCP/IP based printers, and printers shared from Linux CUPS servers. Other printers can be found by hitting "More Printers."
9. Again, yes, the HP drivers can not be used over a generic TCP/IP connection such as LPD, IPP, or socket. The Gimp-Print drivers do work over these connections. So do the HPIJS drivers. The HPIJS drivers can be found here: http://www.macupdate.com/info.php/id/9979.
10. This is true. If the TCP/IP address changes on a printer then you need to re-add the printer.
I hope this is helpful.

More Crashing Issues

I posted this on September 12th, and concluded I needed a new power supply.
I purchased an Enermax EG475P 470W PSU, since that seemed to be the likely conclusion of my problems.
I went from my old PSU with these specs:
Ultra ATX Switching 400W, Model #WIN-400PS
+3.3V = 15.0A
+5V = 30.0A
+12V = 17.0
-5V = 0.6A
-12V = 0.6A
+5VSB = 2.0A
To these specs:
Enermax EG475P 470W
+3.3V = 34A
+5V = 40A
+12V = 33A
I am still getting the crashes that I explained in my first thread.
Before buying the new PSU I had tried everything I knew to do. When I got these crashes even after installing the new PSU, someone told me to try underclocking my card to see if it might be a heat issue. I underclocked it more than 10%, with no changes.
It isn't a CPU heat issue either; I ran Motherboard Monitor 4 while stress-testing with a game and the temperature never went past 61C. That isn't ideal, I know, but I read threads on this board from people saying their Prescotts are running 70C, 80C, or even higher. According to Speedfan, my four case fans are all running at 100% RPM. At idle, the case temperature is 34C. Under load, it never goes past 37C.
I don't really know what to do. Any ideas?
Intel Pentium 4 Prescott 2.8GHz HTT w/ 800MHz FSB
MSI 865PE Neo2-PFISR motherboard (BIOS ver. 3.8)
2x512MB Kingston PC3200 DDR SDRAM @ 400MHz
Maxtor 6Y120M0 120GB HDD
Diamond Viper Radeon 9600XT 256MB (Catalyst 4.9s)
Creative SB Live 5.1 (driver ver. 5.14)

I included them in my first post, but here they are anyway.
Intel Pentium 4 Prescott 2.8GHz HTT w/ 800MHz FSB
MSI 865PE Neo2-PFISR motherboard (BIOS ver. 3.8)
2x512MB Kingston PC3200 DDR SDRAM @ 400MHz
Maxtor 6Y120M0 120GB HDD
Diamond Viper Radeon 9600XT 256MB (Catalyst 4.9s)
Creative SB Live 5.1 (driver ver. 5.14)
Enermax EG475P 470W
+3.3V = 34A
+5V = 40A
+12V = 33A
And here's the problem:
Quote
Sometimes it will crash as I described in the other thread, the video and sound locks up, nothing responds, have to hit power button.
Other times it does something different. For example, while playing BF1942, when the server changes maps, each client does a CD check during which my screen resolution changes to some low resolution, then back to normal resolution (which is 1280x960x85, btw). Every few times* it does this, my system restarts itself. Back to the POST screen. My computer restarts normally after this happens. When I get back to Windows, I get a popup message saying "Windows has recovered from a serious error. Please send an error report, blah blah." I got these crashes before upgrading my PSU as well, but thought that the PSU was causing it. I thought that the resolution changes + CPU load from loading a new map was putting too heavy a load on my system, which my cheap PSU couldn't handle, and thus shut itself down. But these crashes are continuing after upgrading to a PSU which should be able to handle just about anything.
*It isn't a consistent pattern. Sometimes it will restart during the first map change. Other times it works fine for four or five or six times, then it will crash.
I also listed the Blue Screen error message in this thread too. You sure you read the right thread?

More skipping issues...

i'm so upset with dvdsp, i feel like every dvd i make ends up skipping in the clients' dvd players. i shot hdv, edited in native hdv 1080i60, used compressor to make a best quality 150 min ac3 and m2v, and used dvdsp to burn and it plays fine in my macbook pro but skips and stops playing in my ps3 AND xbox 360. what is my issue here? bad dvds? all my software is up to date and i'm using a hv30 and lacie 7200 external firewire 400 drive.

Don't jump to conclusion . Meters on players are terribly innacurate. Beside 3.7 is really low - you couldn't be happy with the quality Im sure at that rate! Re-do the encode again but make sure you've set the correct bitrate based on the length of your source. use a good bitrate calculator to get your target anf peak bitrate settings. Try another batch of good media and play the disc again. Try more than one player if need be.
here's a good calculator:
http://www.videohelp.com/calc.htm
Message was edited by: Eric Pautsch1
Message was edited by: Eric Pautsch1

IChat/Photobooth More Download Issues.

i've looked through many forms relating to this, but NONE has helped me at all. i downloaded "More iChat Effects 2.0.4" at
http://www.apple.com/downloads/macosx/email_chat/moreichateffects.html
for a lot of the settings, it comes out all inverted. its a brand new laptop, nothing is wrong with my iSight. i have the 10.6.4 version. here is my hardware info.
"Hardware Overview:
Model Name: MacBook Pro
Model Identifier: MacBookPro7,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.4 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 3 MB
Memory: 4 GB"
i know that you can change it to the 32-bit, but when ever i try switching it over to that, nothing comes up when i press down command-i. here is some more info if it can at all help you.
"System Software Overview:
System Version: Mac OS X 10.6.4 (10F569)
Kernel Version: Darwin 10.4.0
Boot Volume: Macintosh HD
Boot Mode: Normal
Computer Name: ----
User Name: ----
Secure Virtual Memory: Enabled
64-bit Kernel and Extensions: No
Time since boot: 3:22"
i do have snow leopard, and i am aware that screws the effects up. so help? please?

Welcome to Discussions, cakwinn
cakwinn wrote:
i've looked through many forms relating to this, but ...
i know that you can change it to the 32-bit, but when ever i try switching it over to that, nothing comes up when i press down command-i. ...
(1) *Only applications* can show the "_Open in 32-bit mode_" option.
If you are using "Get Info" on some other filetype, not seeing 32-bit is expected. However, you should still see the Get Info window.
(2) Test as follows: select any application's iCon by clicking once on it in your Mac's "Applications" folder. Then hold down the "⌘" key and tap the "i " key once. The Get Info window should open.
(3) Having used the process in (2), if you still see "... nothing comes up ..."
Does that mean that no Get Info window opens?
If you are uncertain that you are seeing a Get Info window, here is a picture of one:
(Yours will contain different information.)
(4) If you do not see any "Get Info" window, try using the *File > Get Info* menu command instead of the "⌘ i" keyboard shortcut.
... i do have snow leopard, and i am aware that screws the effects up. so help? please?
I do not understand this.
(5) If this paragraph is still related to your +Get Info+ problem, see the suggestions above.
(6) If this paragraph relates to "download issues", please provide some explanation of the problem.
(7) If this paragraph is still about help with More iChat Effects problems, my best suggestion is you carefully follow the developer's uninstall instructions to remove this third-party add-on if it will not work with the Mac OS.
If you want keep trying to use MiE with SL, take a look at this recent thread about the same 32-bit and color-inverted problems you mention for other suggestions:
http://discussions.apple.com/thread.jspa?messageID=11879328&#11879328
(8) We will watch for your status update.
If you need other ideas to resolve your issue(s), we will try to offer specific suggestions based on the details in your response.
Because of the number of possible issues involved, please key your responses to the numbered items above. Add new numbers if I missed something.
EZ Jim
Mac Pro Quad Core (Early 2009) 2.93Ghz w/Mac OS X (10.6.4) MacBook Pro (13 inch, Mid 2009) 2.26GHz (10.6.4)
LED Cinema Display G4 PowerBook 1.67GHz (10.4.11) iBookSE 366MHz (10.3.9) External iSight

HP ENVY 6t has many issues with USB headphone, Bluetooth and more serious issue

HP ENVY 6t doesn't work with USB headphone, unfortunately. could u let me know how to fix it?
Bluetooth mouse has been working for a day, it suddenly stopped working. Having checked the PC bluetooth connection, which said "Working properly". Could you let me know how to re-connect, or re-work?
"Not complete shut-down" blue screen issue right after receiving the HP PC when I closed display to be in sleep mode.
I see the "Safe mode" "...." or "Normal mode" screen always.
The HP PC is not stable UNFORTUNATELY.
Even if just brand new HP PC, there seems to be many issues.

I would recommend using this document for your mouse: http://goo.gl/XDRRy
And using this document to troubleshoot your headphones issue: http://goo.gl/hV9fu
Most of the time with USB headphones, you have to download the driver from the manufacturer before they will work properly.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

More alignment issues

hi,
I'm hardly an expert - but I have made great strides because of helpful people who throw me a hint.
my site: www.kirarmerica.com
I still have JUST a FEW alignment issues. I like to have everything centered, so now I am just down to my spec sheets.
I know that they might not be configured ALL the same, but I am hoping I can change a few things
please look at Kira America | Products
click on any spec sheet and you will see that the headers menu and sometimes the footer stays centered, but the spec info jumps to the left of the page.
I've found the correct .css to edit. but I cant quite figure out how to align the columns vertically on the page.
for example if I put a margin on #right_column it put it in the right spot, but then the rest of the content jumps all over the page.
any hints would be helpful!

These changes will center content in white area
#container h1, #container h2, #container h3, #container h4, #container h5, #container h6 {
    border-bottom: 1px solid #DEDACB;
    padding-bottom: 8px;
    text-align: center;
.excel214 {
    border: medium none;
    color: #000000;
    font-family: Calibri,sans-serif;
    font-size: 11pt;
    font-style: normal;
    font-weight: 400;
margin-left: auto;
    margin-right: auto;
    padding-left: 1px;
    padding-right: 1px;
    padding-top: 1px;
    text-decoration: none;
    vertical-align: bottom;
    white-space: nowrap;

More Gamma Issues

Today, I wanted to focus on the current state of RAM Preview.
Last week, I went through exhaustive testing of color accuracy through an After Effects workflow, with source material generated out of Final Cut Studio 2 & 3, all 1920x1080 29.97i. I performed tests through After Effects CS3, CS4, and CS5. In all cases, we used both Tektronix 601A and The results were eye-popping.
After going through your notes about the recent gamma issues, I made your recommended changes to the Interpretation Rules, as well as the MediacoreQTGammaRulesCSx, along with the proper color management settings (Rec 709).
Setup:
MacPro 3GHz 8-core (MacPro2,1)
16GB of RAM
AJA Kona 3 v.7.5.1 or v.8 drivers
OS 10.5.8
QT 7.6.4
In the case of CS3, gamma accuracy simply can not be had either via RAM Preview nor via rendered files. In CS4, one can clearly see that Adobe did a very good clean up job on gamma accuracy but those fixes are limited to rendered files. RAM Preview using the QuickTime Output Component through an AJA Kona xx card aren’t even close when looking at Gamma. As a result, black levels are several IRE too low. If we use the AJA Adobe Plug-ins for 7.5.1, I can get accurate Gamma BUT I can’t get real-time frame rates if I use a Project bit depth > 8bit.
So I have a choice, inaccurate Gamma or bit limited RAM Preview. So why is running a project in 8-bit mode bad? Banding and color skew. Most camcorder acquisition formats are 8bit YUV. Doing conversions from 8bit YUV to 8bit RGB are simply bad. You are converting from a scaled color space in which your usable levels are 16-235 (YUV) over to 0-255 (RGB). As a results, you are going to have plenty of errors. By converting to a 16-bit RGB space, those errors are virtually eliminated.
Now we both know that RAM Preview desperately needs a “do-over” and has for years. But, it is what we have today and our clients desperately need a solution that offers both gamma accuracy and real-time frame rates in 16 & 32bit modes.
Thank you for listening

I tried the three solutions noted on the page, but none of them actually "address" what my problem is. I could not find the directory in the registry, nor could I create one. Is there any last-ditch attempt or solution? I was told I could turn the "time" back on my computer, though I don't want to lose my information or run the risk of nothing happening. For now, thanks for your help.
ADVICE WELCOME!

Gallery - more IE issues

Hi,
I've read about several IE issues but this one was new to me:
I've noticed that several of my images doesn't look very good when
I use IE to open the spry gallery. The dark (255,255,255) areas is
replaced by white dots.
Take a look at my sample gallery at
http://spry.touam.se.
Mozilla opens the galley nicely, but IE doesn't.
If I open the jpg directly in IE using File/Open it looks
just fine, so there's nothing wrong with the image itself.
Any ideas?

I had this issue with some of pictures as well - thought
Photoshop was playing tricks on me when I exporte them.
Nonetheless, it appears to be an IE redraw issue - it
literally leaves little white holes/specs in the image.
A solution I found was to open the CSS file and browse to the
#mainImageOutline selector class and either:
1. Change background-color: #eee; to background-color: #000;
<<000 representing black, the current background color of the
page.
2. or remove it altogether just by adding the letter x in
front of it like this xbackground-color: #eee; << the letter
x is a hide hack
hope this helps
h

WRVS4400N Issues

Ok I've been stupid :/ I bought this Wireless Router because of its VPN capability and N connectivity. When I installed this router everything seems fine until the day after. after some hours my machines are unable to get an IP adres from this router, only my wired machines get a IP adres. VPN access doesn't work, I always get "Verifying Network" and it stucks there. So I started reading on the I'net,.......... o my god then I came to the conclusion that almost everybody has troubles with this expensive router that doesn't seem to work and Linksys failed to give his users an answer! So my question is there somebody who got this router working and stable? Are there any tips or tricks I missed to get this machine working?

I found some kind of Silver bullet :/
First of all the different language/country websites have different downloads on there site. For example on the Belgium website of linksys there is no firmware download possible. Only the Quickvpn client can you download there.
The American Website is the most updated one I found.
I got my router now working for 2 weeks without any reset . What I did:
1ste I've downgraded the firmware to 1.0.16 with the wrvs4400n recovery tool.
2th I have set my Wireless to B/G only (N disabled)
this setup seems stable, my router is now working for about 2 weeks without any problem.
Maybe this B/G setup also works on the newer firmware, but I'm glad the thing is up and running and I don't want to mess it up again
So if anybody with the newer firmware could test the B/G only stability

More wrvs4400n issues

Similar Messages

Maybe you are looking for