MRP Batch job RMMRP000 not woking but MD01 works

Hi Gurus,
We have a batch job running nightly for program RMMRP000 (MRP) in the morning when we check it, it does not propose any requirment. But when we run MD01 in the morning. It proposes requirments for materials. Why is this happening? I was told to check if the material is in the planning file and it is.
What Am i missing.
Thanks,
Jograd

Hi,
That's okay, I think your background job running is no problem, because there are 64 materials planned. You should double check the other parts' planning file entry, whether they should be taken into account the MRP run? Normally there are the following prerequisitions:
Material master data changed, e.g. some fields in MRP1, 2, 3 and 4 views;
BoM or Routing changed;
The requirements of parts with Higher Low-Level code changed, e.g. sales order, sales scheduling agreement;
Production plan changed.
And so on, all data is relevant to MRP. Check your production plan, it's daily plan or weekly plan!
Regards
Tao

Similar Messages

MRP batch job not creating planned orders

Hi Experts,
Can anyone help with suggestions of where/what to look at with this situation. My MRP background (batch) job is not creating planned orders for materials in certain MRP planning areas as expected, but will create planned orders in other MRP planning areas. Running MD01 or MD03 creates planned orders for materials in all MRP planning areas of the plant as expected.

Ben,
Any time you get a difference between interactive MRP and batch MRP, first look to the planning file.
Start out by finding some of the discrepant parts (no planned orders are being created) Review for the presence of a planning file entry in MD21. If an entry does not exist, create one in MD20. If an entry does exist in MD21, but there is nothing in the NETCH/ NETPL/reset ord/reexpl bom cols, then this means no relevant changes have taken place, and NETCH MRP will ignore the parts. You can optionally reset these flags in MD21.
If you discover that you have one material for which there is nothing in MD21 (no record at all), then you probably have others as well. Run MDAB in Background, which will mass create all the missing entries. Also a good idea to run MDRE in case something has been corrupted.
Here is [OSS note 205681|https://service.sap.com/sap/support/notes/205681] which explains a bit about the planning file. Also, See [OSS 371016|https://service.sap.com/sap/support/notes/371016] which describes a similar problem.
Rgds,
DB49

MRP Batch Job creation

Good morning,
I have been out of the loop for a while in R/3 MRP.
I need to create some MRP batch jobs,
1 will run 6 nights a week for approx 26 weeks
1 will run on a Sunday night for the total horizon.
How do I set these up :o)
Thanks in advance.

> Good morning,
>
> I have been out of the loop for a while in R/3 MRP.
> I need to create some MRP batch jobs,
> 1 will run 6 nights a week for approx 26 weeks
> 1 will run on a Sunday night for the total horizon.
>
> How do I set these up :o)
>
> Thanks in advance.
Hi,
You can go to MDBT, define a variant and maitain it. Schedule the variant. Here you can schedule a varinat on daily basis or weekly basis. So if you give a start date and time on Sunday then the job will run on all the Sundays at the specified time. You can schedule the job every day also on a specified time. I did not find a way to schedule a job for week days only, you may need to take the help of third party job schedulars.
Regards
Vineet

Mrp batch job

Hi all
how we can set MRP batch job. explain me procedure in brief.

Dear,
The program is RMMRP000
Create a Variant for the Program and
Schedule JOB in background:
Go to SM36 create a Job
enter Program and Variant for that program in STEP..
click on Start Condition
Click on DATE and TIME enter date scheduled Start and END times
click on Period Values
Click on HOURLY/WEEKLY etc
CLick on RESTRICTIONS also to use further criteria.
so your job will be scheduled and run as per your requirement.
and in SM37 Transaction check the status of that JOB
Else you can also check in MDBT select the variant and click on scheduling.

I need to setup 7800 Series IP Phones in the CUCM 8.6.2 which by default are not support but will work after install the software. Anyone have document from Cisco as I remember I seen once before.

I need to setup 7800 Series IP Phones in the CUCM 8.6.2 which by default are not support but will work after install the software. Anyone have document from Cisco as I remember I seen once before.

Hi Ali,
I'll just add this reference to the good tips from my friend Manish (+5)
Support for the 7800 series in CUCM 8.6.2 was first added with this
Device Pack;
Cisco Unified Communications Manager
Device Package 8.6(2)(24104-1)Release Notes
Cisco Unified Communications Manager Device Package Release 8.6(2)
adds support for the Cisco IP Phones
7821, 7841, and 7861 running SIP firmware release 10.1(1).
The steps are in this doc
http://www.cisco.com/web/software/282074299/107528/cmterm-devicepack-8.6.2.24104-1_Readme.pdf
You might as well install the latest 8.6.2 Device pack
cmterm-devicepack8.6.2.24112-1.cop.sgn
Cheers!
Rob
"Seek it out and ye shall find "
- OneRepublic

How can I fix my iphone's sound I plugged it in to my radio and the sound came out fine but when I took it out the volume bar dissapered and ever seince all it says volume not available, but it work with headphones in. What can I do to fix it?

How can I fix my iphone's sound I plugged it in to my radio and the sound came out fine but when I took it out the volume bar dissapered and ever seince all it says volume not available, but it work with headphones in. What can I do to fix it?

Try reset all settings.
Settings > General > Reset > Reset all settings. It won't delete any data.

Turn off Spool Printing for MRP Batch Job run

Hi Experts,
Please tell on how to turn off the printing of a Batch Job which is an MRP Batch Run. Can this be done while creating the Job? We really don't need the prinout for this job. Thanks.
Points will be awarded.
Regards,
LM

Yes, this can be done while scheduling a job. When creating a job step (transaction SM36) there is a button "Printer specifications". Select any printer there and option "Send to SAP spool". Spool request will be created but it won't be printed out.
If you are using RMMRP000 program, you also might want to uncheck "Display material list" checkbox on the selection screen. If using other program, see if there is an option to disable the log.

Invoice creation in batch jobas are not in sequence

Hello ,
I schedule two batch job with diffrent variant at the same time. When invoices are created in batch job there numbers are not in sequence. If I check creation time then Invoice creation time of Invoice number 2 is latter than invoice creation time of number5.
As per number range concept Invoice 2 should create before Invoice 5.
Why this is happening?
Regards
RDC

>
> Thanks for the soon reply but here my legacy system is File it is having the fields like INV details and country key and customer details these details i want to send it to Target Ecc system based on the country .
Use File Adapter in sender side to read the data from Legacy System ,if the legacy system data format not XML then use File content conversion in Sender comuniction channel to convert in to XML.
> for exp: If the country is Us then create the vendor invoice in the Ecc system , if the country is IND then check whether the existed customer in the ECC system or not if Existed then those details update into one more legacy system .
>
You have to perfrom RFC Lookup in mapping level if the coiuntry is IND,anyway you are on PI7.11 so you can perform RFC llok to check the it is existed customer or not. search in sdn for RFC look up.
Finally use enhanced Receiver determination to determin receiver.
search in sdn you will get it hot to determine dthe receiver...everything..
the requirement not complex..
Regards,
Raj

T code to find sales orders/Deliveries for which batch job could not create

Hi
Once a PGI has been created for a sales order, the invoice should be created in nightly batch. Once is a while, something is wrong and SAP cannot create the invoice. I know there is a transaction that will list the orders / deliveries where SAP could not create the invoice. Can you tell me what that t-code is? Thanks

Lakshmipathy
I think you did not get my point corectly , I know , billing docs due list , what I need was after batch job running , for some deliveries , due to some reason , billing docs might not have created .
Business needs to know only thsese delivery docs in a T code or table but not all the due document . I did not find answer for this question in SDN .
I got the answer now for this question , it is V.21 .
Thanks for your time .

Batch jobs with status "active" but aren't really active

We have 4 jobs that show up in SM37 with a status of "active", but they aren't really active.
They are from 1998, and the client & server listed no longer exist. The PIDs listed do not exist on any servers.
We have tried to cancel, delete, check status, nothing works.
Is there some way to get rid of these jobs from the system?
RSBTCDEL / RSBTCDEL2 will not work, because the jobs are active.
Thank you.

When I try to cancel the "active" job, I get message "Error occured determining batch work process information" (Message BT241).
When I do a Check Status, it just says "1 jobs were checked and 0 jobs were corrected"
When I try to delete, it says "Job xxxx is active. The selected function cannot be performed"
We have jobs SAP_REORG_JOBS and SAP_REORG_JOBSTATISTIC running. I cannot find a standard job SAP_REORG_JOBSSTATUS mentioned in Yves reply. If this existst, can you tell me what program is being executed by the job?
We shut down / restarted one of the systems that has some of the old jobs yesterday, and the problem still exists.
We are at Basis release 702, SP 12.
I will take a look at the BP_JOB* function modules

Creation of MRP Batch job

Hello PP Sapperu2019s
I need to create a MRP batchjob for one of my plant u2013 9030.I need to know the below highlighted details,
Job name : MRP Plant 9030
*Programname : *
*Variant: *
Frequency : Daily
Timing : 01.00 (during the night)
Step user :
Please help me to proceed with creation of MRP batchjob.
My requirement is to run MRP every night that reschedule the purchase order and create new purchase requestion in Total Horizon.
Need any further input please let me know.
PS:I also refer MDBT for the MRP jobs whihc already created for some other plants but seems to be different from the above requirement.
Cheers,
Kumar.S

For the job which you refer to, go to the spool & study the section 'Runtime statistics'. It will let you know which section took how much time & based on that you would be able to infer what has caused the delay & thereby take suitable actions.
Also note, there is no generic rules as such, each case has to be analyzed if there is a delay. But in general it is better to ensure your planning file entries are consistent, processing key - NETPL or NETCH & planning mode is 1.
I guess this thread has gone way beyond the initial posting, so for any further analysis on this MRP job I would strongly suggest that you sit down with the MRP controller & analyze the same. I am quite sure it shouldn't be difficult in interpreting the results.
Good luck.

VF05 can use in Batch Job or not?

I have problem because when I use VF05 to query by 1 sale organization in 1 month when i execute in foreground it will be short dump [because it take a long time].
So Please give me solution to use VF05 to crate batch job

Hi;
The program behind VF05 is SAPMV65A and this program does not have a selection screen and so you cannot schedule a job for this T.code in the background.
Regards,
Mani

Deskjet 3054 not printing but scanner works

Hello!
I have a Deskjet 3054 per label on the printer, however, but the IP address says it's Deskjet 3050 All-in-One J610a. My computer is Mac 10.9.5. I've read through other posts and have updated all my software via Apple's Software Update.
The symptoms are as below:
- The scanner works (I can scan a page and view it on my computer)
- Printer report works (that's where I got the IP address)
- On Mac's Printer & Scanners, the printer is recognized and connected
- However, when I print a document, the queue shows up, shows the job is being processed. However, the printer does not move at all. I cannot hear the cartridge move. Then the queue shows that the job is done and the queue is empty.
Please help!
Thanks!
Moonlit
This question was solved.
View Solution.

Hi @Michelle_sonata
I would like to help you print from your Mac to your Deskjet 3054. I understand the print queue says that the print job was done but nothing prints. Please follow the steps below and let me know the outcome of your efforts;
Reset Printing System
Click the Apple icon (   ), and then click System Preferences.
In the Hardware section, click Print & Fax/Scan. The Print & Fax/Scan dialog box opens.
Right-click (or  Ctrl  +click) in the left panel, and then click Reset printing system…
Click OK to confirm the reset.
Type the correct Name and Password.
Click OK to reset the printing system. The Print & Fax dialog box shows no printer selected
Note: This will remove all printers in the print and Fax/Scan, any printer removed can be re-added later by clicking the plus (+) symbol.
Repair Disk Permissions
On the Dock, click Applications, and then click Utilities.
Double-click Disk Utility.
Highlight your hard drive/partition on the left (by default this is "Macintosh HD").
Click the Repair Disk Permissions button at the bottom of the window.
Once the repair is complete, restart the computer and add the printer back.
Install the HP Printer Drivers for OS X.
When you add the printer, please ensure you are using the HP driver, not the AirPrint driver.
Select Add other Printer or Scanner
Select the printer you are adding and next to 'Use' you can select the printer driver
I look forward to hearing from you.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

CD not readable but DVD works

My early 2010 MBP has started shwoing the following error when I insert a CD:
"The disk you inserted was not readable by this computer."
DVDs play with no problem at all and also, if I chose the ignore the ignore option to the CD error above, I can use the old Songbird app to rip music from CDs in to FLAC format - again with no problem. I ran a CD cleaner through the drive but no difference.
I have also tried starting the macbook with 'D' pressed to get the hardware diagnostics but this just gives me a white screen for a while before booting up normally.
Running Mavericks, Verified, disk and repaired permissions.
Thanks in advance.

I've already used a cleaning CD to no effect.
It still reads CDs using songbird, however I can no longer import them into itunes. I've tried redownloading itunes as well.
I have since dug out the CDROMs/DVDs that came with it(which play ok) and did a 'D' restart to do a diagnostics test and it didn't find any errors at all.

AppLocker service issue: AppIDSvc not running, but enforcement working.

I have a strange problem with AppLocker. I configured the service (AppIDSvc) and some policies using group policy and deployed it to some computers in my domain. I logged onto one of the systems and verified that AppIDSvc was running, and that
enforcement and logging were working correctly.
Later, I decided to expand that policy to more computers. I reorganized the policies somewhat, but the RSOP is the same. I logged onto one of the new machines that I applied the policy to, and noticed that the service was not running and nothing
audited in the AppLocker logs. When I try to start the service, I get "System error 31 has occurred. A device attached to the system is not functioning."
This is strange, but what is more strange is that on the first set of systems I deployed AppLocker to, I am seeing the same behavior from the service: not starting, and attempts to start result in the same error. However, AppLocker is still working!
It is still enforcing the original policies I created, and is still logging events.
I did a little more investigation, and I see that the AppID service (which AppIDSvc depends on) is running, and must be the service doing the heavy lifting behind the scenes. When I prevent the AppID service from starting (by removing it from [HKLM\SYSTEM\CurrentControlSet\services]),
and restart the system; the enforcement/logging stops. When I put it back, it restarts. But, I cannot get it to start on systems other than the original test group, and obviously something is wrong that the AppIDSvc won't start.
It's as if the enforcement mechanism (provided by AppId.sys?) cannot be called by the AppIDSvc, or AppIDSvc cannot access the resources in use by AppID; or something to that effect. I have tried auditing the behavior of the system using procmon, but
haven't made much headway yet.
Any insight into this issue, or how to better troubleshoot it would be greatly appreciated.

Despite hours of troubleshooting, just minutes after resorting to posting about this problem I solved it!
The issue ended up being that when I updated my group policy to ensure that the AppIDSvc was enabled, in my due diligence to ensure that everything was set correctly, I selected the radio button for "Log on as: Local System account." In fact, this
service must run under the "NT Authority\Local Service" account, not the Local System account. Once the account settings were corrected, the service started no problem.
I have updated my group policy to fix the issue and all seems to be well.

MRP Batch job RMMRP000 not woking but MD01 works

Similar Messages

Maybe you are looking for