MSI K8N NEO-FSR BIOS Flash Corrupt

So there was an updated BIOS for my motherboard version 1.8 while I had 1.7. I went ahead and updated and it went fine. But then I noticed that my CPU speed was dramatically reduced and the multiplier was set to 5.0 giving me a 1ghz CPU. While I thought maybe the CMOS needed to be cleared I went ahead and did that but to no avail I wasnt able to fix that problem. I went over to the MSI Live Update to check for a new BIOS update and it had said that I had 1.8 version while the current version is 1.7. Just a few days before it said 1.8 was the latest. Hmmm. So I went off to the MSI website to find version 1.7 and downloaded it. To my surprise version 1.8 was available on the MSI website. I used the WinFlash program to flash my BIOS. Before doing so I closed all open applications including anti-virus, browsers, chatting programs, and so forth. But the flash was going VERY slow and it stopped with unable to verify bios. This made me scared pooless. After I restarted to no surprise my computer started up with BIOS Checksum error and asked for a floppy. I didn't have a floppy drive connected at the time but the computer shut itself off automatically. So I went and connected and floppy and looked up online at the MSI website about how to recover the BIOS. I found it and for my AWARD bios i followed the procedure. But each time it detects the floppy drive and then the computer shuts itself off. Even if i have no disc inside the floppy drive it'll shut off. Is it supposed to do this? I am unable to reflash my BIOS because of this behavior. I don't know what the cause of this problem is now. Did maybe the recovery portion of the BIOS get corrupted too? Please help. Let me know if you need any more information. Thanks in advanced. My specs are below btw:
MSI K8N NEO FSR
AWARD REV. 1.8
AMD ATHLON 3200+ 754
PDP 2x512MB RAM
NVIDIA GeForce 6800 Ultra
Ultra-X 500watt
WD 160GB IDE, Seagate 200GB IDE
Pioneer D-A07
Windows XP SP2, Gentoo Linux, Ubuntu Linux

Okay I tried taking unnecessary stuff out but it didn't help. I'm actually having the same problem this guy is having : https://forum-en.msi.com/index.php?topic=86508.0
Hmm looks like i might be in for a new motherboard or i can try the RMA process but I dont know how long that will take. Other than that...I dont know what to do. I could buy myself a new bios flash chip but they're damn expensive and I'd rather just buy a new motherboard. On another note I noticed that when I boot up the pc and i see that it detects the floppy I immediately pressed the reset button but it'll still shut down. So it's as if there is a timer somewhere. What the hell is up with this? It also seems MSI didn't release bad BIOS releases for my board only. Seems like people with other boards are having tons of problems with the latest BIOS releases.

Similar Messages

MSI K8N Neo-FSR BIOS

Where can I download old version of BIOS for my MB? Curently I have v1.8 (this version was on MB when i bought it) and I do not have USB2.0 support with this version of BIOS. I need v1.7. So if anyone knows link to it, please post it.

Here you are:
-->7030nms.170<--
Right click and choose "save target" .

[ram]Kingston + MSI K8N Neo-FSR?

my system:
AMD Athlon 64 3000+, 2.0ghz
MSI K8N Neo-FSR(bios 1.40)
Asus V9999 GeForce 6800 256MB Gamer Ed. AGP
Audigy 2 zs
Win xp pro sp1
Hiper power 420W
I just bought the Kingston ValueR. PC3200 DDR-DIMM 1024MB Kit w/two matched ValueRAM 512MB.
When I boot up the pc just makes a sound piip piip piiip continuing....
I can't do anything since it wont boot up & i tried diffrent dimm slots but it didn't work :(
Earlier i've set the settings to t1 & the volt to 2.56 from before. Does this has something to do with it ? How can I reset the bios if I can't even get in dos :s
What should I do ?

Reset the cmos using the Jumper, is you have a manual it will show you where this is located. It will set the Bios back to Default,then you have to set it up the way you want it again. To get the RAM working set it to DDR333=166, that should sort out the No Post.
Your going to be out of luck here as the 'support' is basicaly non-existent, or just replies from people trying to get their post count up higher, I'm afraid to say.
Good luck.

Strange Temp Jumps on MSI K8N Neo-FSR

Hi!
I got a MSI K8N Neo-FSR.
My temp in speedfan jumps from 36 to 42 just like that then back to 36.
It's pretty disturbing to see that.. And I wounder does someone else have the same problem? Then I don't know how accurate the new BIOS for this mb is. On the Abit I hade before the temp was 34 idle.. Today I allso bend the small metal pice that you screw in on the Zalman ALCU cpu cooler so it would fit and press harder, then the temp sank from 42 to 36 idle. And the CoreCenter shows a temp on 44 now and speedfan 36 but jumps to 40-42 just for a second.
Anyone know what the problam can be? It's kinda anyoing when you OC some because you don't know the right temp.

You should try and update your bios , speedfan and core center showed different temperatures for me too until i updated my bios. On the other hand i have a different problem, that is: when i start my pc(cold start) my idle temperature is 40 degrees but if i restart it drops to 30, does someone have any clue why?

OC MSI K8N NEO-FSR

is there any problems with OC this mobo..
MSI K8N NEO-FSR MS-7030 NVIDIA nForce3 250GB 754
and can the cpu be OC without OC the ram to
Cheers Lads

you keep memory freq. in range by setup mem. index. e.g. for CPU HTT 250 with mem. index of 166, will produce memory freq. 200Mhz.

Ms-7030 msi k8n neo fsr wont start

i made my system a follows.
amd 2800+ 64
msi k8n neo fsr
kingston 400mhz ddr value ram
6600gt inno3d agp
wd800 80gb hardrive
300 watts psu
brought the system home everything was working fine except for continous stuttering on hl2. also wid it came a smart cobra lite 56k modem from zoltrix, which was installed while makign the system, the modem had been deteced but when i tried to connect to the net, the status of the modem was found to be not connected, i removed the modem, restarted by switching the pci slots and everything but to no avail, put in an older zoltrix modem from my old pc, to no avail the modem just wudnt get recognized. the same modem though worked in my older p3 system. i took the systm to the place where they assembled it.as the system booted the modem got deteced, got winxpsp2 installed wid a fresh install. everything worked fine for a day untilt eh modem once again went back into death mode.took it back to the hardware shop i remember they were using an older keyboard on it too, well as they pressd the power button, the cpu fan and the gfx card fan moved a second and then stopped no booting
they replaced mobo then and there. even the same problem occured wid the new mobo, i left the system there to be tested but the thing i dont understand is they had assembled an tested the system by using the old keyboard and even then there was no problem. this time the system was working but as it reached the assemblers the cpu and gfxs card fan moved a sec as if power was fed for a second and dided changed psu's on one try on dry boot that is widout hd connected. the fans continously worked we removed power put into chasis and tried again to start but to no avail.
cud it really be the keyboard problem if that is solved then the problem left to deal wid is the modem wud the pci slots act the same way even on the newer board or chaning modems wud do any good, changed rams also that wudnt help booting either.
in both of the new mobos i didnt get the msi sticker that adds to my frustration.
posted this on another forum too, tha guy was havng problem using an older keyboard.

its really nice of u guys to reply so quickly its really appreciated. the thing is if the psu wasnt upto the job it wud have given away 3 days ago. but it didnt other psu tried also same problem. after a couple of hours ill be off to the hardware shop to see wat came out. the ram was reseated properly on all 3 slots.
plus the 300watts psu may not even be 300 cuz its locally made and stupid quality maybe lower to around 250, but the system worked fine all along, checked rail supplies on the mobo mopnitor and they seemed fine.will keep u guys updated.

K8N Neo FSR Bios overclocking functions help needed

Hi all, I am a small pc builder for the family and i have found some problems with the bios of my uncles K8N neo FSR which I recommended for him. Basically it wouldn't seem to overclock with the 'Dynamic Overclocking' function on bios v1.7 but did manually by adjusting FSB incrementally (ie from 200 to 205 Mhz). When I questioned this before someone had mentioned that it could be ok to run like this. However I have since updated the bios to v1.9 and even v2.1 as they became available but now neither seem to overclock manually nor using 'Dynamic overclocking'
Firstly though, can someone clear up my first conception; To test if the Dynamic Overclocking function is working can I set it to a higher setting (ie.'Commander'), save and exit bios (restarting) ---> go straight back into bios ----> go straight back into Cell Menu and check 'Current frequency of cpu' has changed?
I only ask this as if this is the case then my Dynamic Overclocking function hasn't worked with three bios' and I wont bother with anything until I RMA the board lol, as I have never been able to change the frequency of my cpu at boot/bios stage with the dynamic overclocking function.
Can anyone help me?

Hi Stu, yesterday I think i found out what u mean lol. I studied a 'Sticky' ? about overclocking A64s and found some interesting stuff. Apparently overclocking the HTT is dangerous, and A64s are always at least half locked. Now with this in mind Ive been wondering if there are interlocks built into my mainboard stopping me from using the 'CPU Overclock' function to overclock my pc manually from the set 200Mhz while my HTT is still set at 4x. -I say this as the HTT on my system is 800Mhz for a socket754 Sempron 3000Bx, thus overclocking this would increase my HTT above the 800Mhz threashold (I think) lol. All sounds complex but I think Ive figured it out as Im following instructions from the sticky to lower my HTT multiplier before increasing my cpu overclock. Its hard as my mainboard has Nforce3 chipset which has different ways of overclocking to every other board lol. So far I have managed to increase the overclock, but only when the HTT multiplier is lowered to 3x. I have also lowered my cpu multiplier though, and thus am trying to figure out where my 1810Mhz clock speed has changed to 1630 lol. Will try again now. I want to raise the clock speed above 1810, keeping the HTT lower than 800 and leaving the memory alone at 400DDR lol. Im hoping the memory is seperate as it seems to be on this chipset.

MSI K8N Neo FSR Game port ??? !!!

Hi,
I can't install my game port from my Creative sound card, i have try namy drivers ... I have try a another sound card, Aztech PCI288 and i have the same probleme.
Impossible to have game port !
I need a solution, this is must do working ! i can't take ma Sidewinder in the "poubelle" ! (C'est du francais )
MSI found me a solution !
bye

I get response from MSI as the following.
As the chipset on K8N Neo-FSR is nForce 3, due to the design limitation of nForce chipset, it can not support Legacy I/O decode device. However, most game port on PCI card belongs to legacy I/O decode mode, so the game port could not be used.
In fact, currently most game port on legacy I/O decode device is replaced by the corresponding USB type device. You can use USB port game devices instead of game port on PCI card.
It seems that we could not use the game port on sound card on nvidia platform.

MSI K8N Neo FSR HELP!!!

Hello,
Just bought a msi k8n neo board with amd 64 +3200 processor combo. I have everything plugged in correctly ( i hope) and when i boot up the system hangs for a bit Detecting the IDE Drives. Once it has finished detecting it goes on Detecting the DMI Pool Data, after that I get an error that reads. "Disk boot failure, insert system disk and press enter." Sometimes it will skip or finish the DMI pool data detection and attempt to start windows but I get a blue screen that says I will need to reboot my system.
Please please please help!!!

does it manage to detect any ide devices at all? if not then its probable maste/slave jumper settings... if it does detect them, then its probably cos u need to install windows

MSI K8T Neo-FIS2R, BIOS flash???

I'm trying to flash my bios but i get this wrong message after restart: CMOS SETTINGS WRONG, if you have built sata raid array previously, go to "P20378 sata controller" set as raid. I've tried that but it dosn't help.......what should i do???
Motherboard: MSI K8T Neo-FIS2R
Harddrives 2 x S-ATA Western Digital 250 Gb, 2 x IDE Seagate 80 Gb

i used to get that almost every time i update BIOS. I forgot the fix, but we need to know as Tiresmoke said whether u r at all using the promise. if Via serials r enough for u (which in this case they r since u only hv 2 sata hd's) then just use these and see what happens.
did u also try to load bios defaults? i think i used to do this when i get that error msg

MSI K8N NEO 2 : bios 1b o 1c what it doesn't work

Am trying to try the bios 1c beta, 1b beta or 1b officials in 1.8 substitution (with this all magnificently works however cannot make the pendrive boot usb)!!
The problem is that the controller raid is not recognized me in any way...
Have already tried to train all the ides, the satas and the raid in the bios but there is no anything to do, with these bioses doesn't see me neither the raid of it the ides to which a DVD and a dvdrw are connected!!!
I have noticed under dos during the start that goes out this message:
Warning: Have option rom Khan not be invoke (vendor ID10DEH Device ID 00DFH)......
What can you/he/she be?

Quote from: perucho07 on 16-January-06, 01:08:56
Hi Mike,
Did you use MSI Live Update 3 in order to Flashing from 1.8 to 1.B0 BIOS? I did it without any problems!
Please check in your CMOS all RAID sattings are enable.
Also you may use the NVIDIA RAID diskette in order to re-ensamble your RAID arrenge.
Hope that's helps.
Cheers,
Pedro
The bios is correctly adjourned and I has trained all the voices that concern the ide and the raid...
The pc jams before starting windows
Quote from: Okay on 16-January-06, 08:11:35
https://forum-en.msi.com/index.php?action=search2
I write from the italy and I don't know well the English therefore is me difficult to find a solution through the looks for!
My configuration is:
Enermax CoolerGiant 535W
MSI K8N NEO2 Platinum
RAM 2*512 GEIL Ultra X PC4400
Winchester 3500 + Zalman 7000B CU
2 hdd Western Digital 10K in raid 0 connected to the doors 3 and 4
1 Controller Adaptec 2940UW (in the 4° slot PCI)
2 hdd in external bos usb
1 DVDrom connected to the ide 1
1 DVDRW connected to the ide 2
With the bios 1.8rev.3 of NFM all works very well however I don't succeed in effecting the pendrive boot usb and therefore I have decided to adjourn the bios.
I have tried the version
- 1b officer
- 1b mod
- 1c mod sideffect
With everybody and three these versions of bios, during the initial phase of I start some pc, the controller raid is not recognized me to which the hdd are connected in raid 0 and therefore the pc doesn't set out!!!
I have trained all the sata, the ide, etc. etc. and with the bios 1.8 work well everything.
How can I do??

MSI K8N Neo Platinum ,bios issue or HW

Hi i am using a system like in the signature described (usind adata instead of twinmos) im cooling with a prometeia system , and the board ist watercooled.
My CPU is a Newcastle (@2800mhz ) my graphic card is the normal 9700pro (it makes no diff in oc if the card is clocked or not)
Now i got some serious problems , i can´t run high fsb sync ? Why ? i wasn´t able to do this with the twinmos ram , but i read twinmos has some serious problems with the nforce3, so i purchased 2*512 mb adata.
I tried different dimm combinations (1/2 ; 1/3) that didn´t made any difference
I tried different bios (1.2 1.25 1.31 1.1) but this didnt made any difference either (using 131 now)
my pci/agp is fix (always 66,67/33,34 in clockgen so its just perfect)
i don´t use any SATA devices (all disabled in bios)
What is my Problem ? is it only a bios problem , or is there hardware in my sys which makes probs? Could it be an IRQ Problem (got 2 pci cards in slot 3 and4 its an IDE raid controller and a soundcard)
i hope there is any help for me :(

Well this is the second time someone mentions problem with Adata DIMMs:
https://forum-en.msi.com/index.php?threadid=55475&sid=
Maybe it's about time to post it here:
https://forum-en.msi.com/index.php?threadid=51997&sid=
For all I can think of right now, either run the board with a single module or both with 5:6 divider

MOVED: OC MSI K8N NEO-FSR

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=107210.0

you keep memory freq. in range by setup mem. index. e.g. for CPU HTT 250 with mem. index of 166, will produce memory freq. 200Mhz.

Msi k8t neo fsr bios help

ive been searching and searching and cant find where to change the multiplier.... i was hoping maybe you guys now where it is or a way to change it i have a athlon 64 3200+ but i want to lower the multi to 9, any ideas

Sorry, I did not read your MB ID correctly. According to MSI website, the K8T Nero series does not have the Cell menu. There may be some 3rd party software that will allow you to change your settings but I am not familiar with any.

K8N Neo FSR, Please Help a Newbie

Hey all,
I'm new to these forums and was wondering if I could get some help or advice. I currently own an athlon 64 3200+ newcastle with a K8N Neo FSR motherboard. I have heard that my mobo is basically a platinum minus the luxury of firewire ports, could I be correct about that? If so, I went to msi.com.tw website to update my drivers and could not help but notice that K8N Neo Platinum has two more updates that whats offered for my FSR, those being CoreCenter 1.7.0.0 and DigiCell 1.03.00.00. I find corecenter to be useful and am wondering will these two updated versions of the apps work with my FSR, and why would MSI not post the updates in the FSR section.
Also, my board came stock with bios 1.2 and I loaded up windows sp2 and all the drivers and such and everything seems to be working fine to my knowledge, cool n quiet on with cpu around 994 to 1004 mhz, temp readings from bios and sandra all report 36-43 degrees C. Does that sound right to anyone, because I'm not a fan of bios flashing, would flashing to the newest official 1.4 be any benefit to me?
One last thing, I encountered a problem with a creative usb mouse and do not know the source of the problem or how to solve it, it is the optical mouse lite with a blue scroll wheel and operates fine, but after I shutdown my computer the mouse light is still on, is that normal or is there anything I can do about it besides shutting down my power supply everytime I turn off my computer.
Sorry for the loads of questions, if anyone actually reads this please provide me some input/insight. Thanks in advance.
System specs:
A64 3200+ Newcastle Year 04 Week 26
MSI K8N Neo FSR Bios V1.2
512 MB PQI Turbo Black Memory
Aspire 500 W psu, 12v = 34 amps
Maxtor 60 gig IDE hd
52x32x52 cdrw

If you look at the prduct page for the K8N Neo FSR, and choose the BIOS link it brings you to page:
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=571&kind=1
Which shows the BIOS' available for the K8N Neo FSR. Notice that 1.3 and 1.4 are available and that the K8N Neo FSR is considered to be a MS7030 which is the same model number of the K8n Neo Platinum. From this I surmise that you can use the same BIOS and drivers and all that the Platinum uses and everything should work fine.
RB

MSI K8N NEO-FSR BIOS Flash Corrupt

Similar Messages

Maybe you are looking for