MSI P67A-C43 B3 and MSI GeForce GTX 660 2GB GDDR5 Twin Frozr III N660 TF 2GD5/O

will MSI GeForce GTX 660 2GB GDDR5 Twin Frozr III work on MSI P67A-C43 B3 ???

Yes.
Make sure you have an adequate power supply.

Similar Messages

Should I get an MSI GTX 560 Ti 448 Twin Frozr III?

I'm thinking of upgrading my graphics card and obviously I'm looking to get one that'll go well together with Premiere (CS 5.5). For now, I've set my sights on the MSI GeForce GTX 560 Ti 448 Cores Twin Frozr III 1280 MB. I'm especially attracted to this card, as from my research it should be particularly quiet in desktop use, which is essential to me. Would this be a good choice, or should I be looking at GTX 570 for instance, or a card with more memory?

Arve,
I appreciate the effective and quiet cooling provided by MSI's non-reference designs. I don't have the exact card you mention, but have a system with a MSI GTX 460 Hawk (twin fans, similar to the Frozr design) and it performs WAY quieter than the GTX 260 reference card I had prior to that. I would not be worried at all regarding noise and cooling with 120mm case fans. When comparing how much air 120mm fans can move to clear video card (and CPU) heat from your case vs. the reference GTX cards pushing air through a VERY tiny space, you can expect quieter and more effective cooling with the Frozer. The only possible caveat that I can think of with the Frozr is that you need at lease 1/2" of space in front of both fans so that air can easily enter the fans. If you have a motherboard / PCIe situation where you need to put a card immediately next to the Frozr, then you should go with a reference design; I suspect that gamers wanting 2, 3, or even 4 video cards running in SLI has a lot to do with why the various "big fan" designs are not more common in the market.
Additional to the cooling subject being discussed so far, there is another Newegg listed GTX 560Ti listed with less cores but 2GB of video RAM. Depending on if you ever edit anything with large frame needs such as large photos in video slide shows or RED 4k, etc., possibly the larger video buffer would be more advantageous to you system than the one you mention above that has a slightly higher core count.
Jim

MSI Nvidia GTX 570(N570) OC twin frozr III modded bios 70.10.27.00.01

MSI GTX 570 (n570) twin frozer III modded bios (70.10.27.00.01 from 17.08.11)
with:
-fan lowest limit down to 20%(default 40%)
-GPU Voltage increased by 0.02v
-3D mode GPU/Shader clock:800/1600mhz (770/1540 default)
-3D mode Memory clock 2200mhz(2000 default).
Those are just safe settings for this videocard so why it wasnt done by default?
w ww.4shared.com/rar/3ImQpH--/MSI570MOD.html include Win32/64 nvflash and original 70.10.27.00.01 bios.
How to flash:
Backup your bios
nvflash -b myrombackup.rom
And flash
nvflash MSI570MOD.rom
y, to continue.
DOING ON YOUR RISK!

Quote from: PeterMac on 10-May-12, 01:13:08
From 50MHz on GPU at idle desktop with single monitor to 770MHz!! with two monitors for what ?
to support the second monitor it seems.
read the link
http://nvidia.custhelp.com/app/answers/detail/a_id/2483

Any news RE: support for NVIDIA GeForce GTX 680MX 2GB GDDR5?

I'm about to purchase a 27" 2012 iMac & would like to install CS6.

I have NO idea how this would be done for a Mac... but I do have a saved link
http://www.vidmuze.com/how-to-enable-gpu-cuda-in-adobe-cs6-for-mac/

MSI P67A-C43 (B3) Not booting with Corsair TR3X6G1600C8D Dominator RAM

The mobo will boot but will not login it starts to hang in booting the OS, also when i try to update the mobo bios with a live CD (with old ram that was fine)
My first question, is Corsair TR3X6G1600C8D Dominator compatible with MSI P67a-C43 (B3)
and why isn't my bios being updated when i didnt update it ever since i bought it in 2011.

Quote
The mobo will boot but will not login it starts to hang in booting the OS, also when i try to update the mobo bios with a live CD (with old ram that was fine)
Update with what LIVE CD?? Did system boot to Windows with old ram and if so what was the old ram??
Quote
My first question, is Corsair TR3X6G1600C8D Dominator compatible with MSI P67a-C43 (B3)
That is a triple channel kit of three sticks made for X58/socket 1366 systems and not for a 1155 system. Three sticks could stress the mem controler too much and result in it not running the sticks at the timings/speed they are meant for. Try just two of those and see if that helps. If so try relaxing timings and/or change to ddr3-1333 for trying three.
Quote
and why isn't my bios being updated when i didnt update it ever since i bought it in 2011.
What? Are you asking about a missing update offered or what do you mean?

MSI Geforce GTX 660 TF 2GD5/OC and Asus problems

Hi there,
just bought a MSI Geforce GTX 660 TF 2GD5/OC with and Asus M5A99X EVO R2.0 mainboard. Installed Windows 7 x64 without any problems. All the drivers work but when I try to install the Nvidia drivers it just says there isn't a compatible graphics card available. Upgrade my motherboards BIOS to 1708 which is the latest one. Still didn't make it work. Hope that anybody can help me because I want to start gaming!
Regards!

Graphics: MSI Nvidia 660 TF 2GB DDR5
CPU: AMD FX-8350 8x 4GHZ L2 8MB L3 8MB
Display: Iiyama ProLite E2280HS-B1
Power supply: OCZ ZT750W
Case: Sharkoon T9 Value black edition
Optical drive: Samsung SH-224BB/BEBE
Input: Logitech MK710 WL Desktop
Mainboard: ASUS M5A99X EVO R2.0 6x USB2 2x USB3 6x SATA GB lan
Bios: 1708
Harddisk: Western Digital WD2002FAEX 2 TB
Memory: 2x G.Skill 8 GB DDR3-1600 Kit
OS: Windows 7 x64

MSI P67A-C43 (B3) & OCZ Vertex 3 VTX3-25SAT3 Issues

Specifications:
Quote
Mobo/Laptop: MSI P67A-C43 (B3)
BIOS: 1.B (2011-04-14)
CPU: Intel Core i5-2500K
RAM: 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 CML8GX3M2A1600C9B
Vid: ASUS ENGTX560 TI DCII TOP/2DI/1GD5 GeForce GTX 560 Ti
PSU: HX750 (CMPSU-750HX)
HDD: OCZ Vertex 3 VTX3-25SAT3-120G v2.11
Chipset: Intel P67 (B3) RSD v10.6.0.1002
OS: Windows 7 Ultimate 64 Bit SP1
Let's start from the beginning: So I built my PC in July and ever since I've been having on and off BSODs with the Vertex 3 drive. Mostly they'll happen once a week. When I first built the machine my drive came with Firmware 2.06. I installed all the drivers from MSI's website as well as the latest Intel Rapid Storage Drivers. Eventually I flashed the SSD to 2.11 when it was released but still had similar issues. Hotplugging was enabled when I installed Windows 7 for the first time AND when I flashed to 2.11 from 2.06. Some members over on the OCZ boards stated this might have been the cause of the BSOD. Basically the PC froze, BSOD'd, restarted, and then the system couldn't detect the drive. I had to power the system down, remove the power cable, wait 10 seconds, re-connect the cable and power on the PC. After I did this Windows booted normally.
I received some advice on the OCZ forums to reset CMOS and leave hotplugging disabled. Then re-flash the drive to 2.11 with hotplugging disabled. Some members thought this would make the drive act like an internal drive, not an external drive. However, a week after doing this the same BSOD appeared. I've started from scratch last week by secure erasing the drive and re-installing Windows, but same issues. I noticed MSI released a new BIOS for my board in July. I have the one from April currently.
Is it worth upgrading my BIOS? The listed fixes don't say anything about SSDs.
I plan on trying this when I get home from work:
Quote from: Tony;676791
Going to keep this brief and to the point, this hack will force the 2 primary sata2 or sata3 ports on the motherboards to be designated Internal only...You can do this hack for all Intel chipsets from around ICH8 onwards in win7 and Vista.
You also need to make sure hotplugging is disabled in uefi/bios if your boards bios has the option(s) do this first before you do any of these regedits etc
1 Remove all traces of Intel drivers on your system, that means remove the management engine driver, the RST driver and the INF driver, you do this thru the programs and features option in control panel. I remove them all before I reboot, the system will automagically set you using the MSAHCI driver.
2 Now reboot, let win7 detect the ssd and reboot again.
3 now open a elevated command window (CMD with administrator privileges) and copy/paste the following...then hit enter.
Code: [Select]
reg.exe add "HKLM\SYSTEM\CurrentControlSet\Services\msahci\Controller0\Channel0" /f /v TreatAsInternalPort /t REG_DWORD /d 0x00000001
Once you hit enter you can then add the following again using copy/paste.
Code: [Select]
reg.exe add "HKLM\SYSTEM\CurrentControlSet\Services\msahci\Controller0\Channel1" /f /v TreatAsInternalPort /t REG_DWORD /d 0x00000001
Hit enter and close CMD.EXE down, reboot
This will now force the 2 sata 3 ports to Internal only, this means they will apply LPM if you set it and will support Automatic Partial to slumber.
I now suggest you experiment with power schemes, for some high performance may work better than balanced...try both
You also need to make sure hotplugging is disabled in uefi do this first before you do any of these regedits etc
If you want to go a step further than this you can try the following...ONLY do this after you have done the steps above.
remove the SSD to start
1 create a temporary win7 install on a hdd, use the msahci driver and once installed do the hack to force the 2 ports to internal only. Have the hdd connected to port 1 on the motherboard.
2 once the install is ready and you have installed toolbox to it power down and connect the SSD to port 0
3 now boot to the HDD, use the manual boot menu option to make sure you are booting to the HDD and make sure hotplugging is OFF in UEFI
4 once in win7, flash the FW to the drive, when its finished flashing, close toolbox, reboot back to the HDD and back into win7...make sure the SSD is detected in my computer.
5 now power off, remove the HDD...then boot to UEFI and make sure to set the SSD as first boot device
6 Power up, boot to the SSD
Stay using the MSAHCI driver for now, do not install any INF, IME or RST drivers.
Edit 09/09/11
Had a few end users quoting disabling TRIM solved BSOD for them...now im not saying it will solve BSOD for all but it may be worth trying. Remember the SandForce controller was originally designed without TRIM in mind, it functions just fine without it so you should see no loss of performance. If you want to help the controller stay fast you could always add some extra over provisioning by reducing the volume on the drive and leaving that space unallocated...totally up to you what you do though....
I like 25% OP on my drives, this means if I have a 120 with 115GB showing in windows I lose 15GB to OP and use 100GB for the volume....
A forum member wrote a little script to enable /disable trim...he wrote in support for wiper for Indilinx drives also...just ignore that part and use the TRIM function only...
http://www.ocztechnologyforum.com/forum/showthread.php?63830-A-small-script-to-enable-disable-Trim
Here is a link to force TRIM also.. http://www.ocztechnologyforum.com/forum/showthread.php?73888-Here-s-a-tool-to-force-TRIM-your-entire-drive&p=523305&viewfull=1#post523305 you could if you wanted use this once a week to force the drive to TRIM all marked deleted blocks if you turn off native TRIM in win7.
Again....not saying this cures any BSOD but a few end users have said they disabled TRIM and issues went away...anything I have suggested here is totally reversible and will do no harm to your systems.
If this doesn't work and I get a BSOD after a week I'll disable TRIM and if that doesn't work I have no idea. OCZ said they're working on a new firmware release so who knows. I just hate feeling like I am a beta tester.
If anyone has any suggestions let me know.

OK, had some time to go test your suggestions here
These are the 1.5V Vengeance RAM Modules. Tried installing 2 of the RAM on slots 2 and 4 on their own. System Boots Fine.
Went into the BIOS and changed the voltage applied to the RAM modules from
AUTO to 1.575V. On AUTO it says is applying 1.5V to the 2x 4GB modules.
Installed the full 4x RAM on all slots... and the system just shuts down. Power cycling again.
What do you think here? Bad Motherboard? Can't think of anything else to try... totally stumped!
Thanks!

MSI P67A-C43 problems

Hey everyone. I recently bought a MSI P67A-C43 using a Intel i5 2500K and everything has been working great until recently. I realized it has a post beep every time you turn it on, which is the short beeps followed by a 5th beep and everything starts running after that. Well for some reason recently my computer turns on and the post beeps go 4 times and then it takes a good 3 minutes or more for the 5th beep to go through and everything starts up. I'm not sure what is going on with it and I'm hoping that the mother board doesn't have an issue.
The System has in it:
- MSI P67A-C43 (B3) Mainboard
- Intel Core i5-2500K
- COOLER MASTER Hyper 212 Plus HSF
- XFX Black Edition P1-750B-CAG9 750W ATX12V v2.2 / ESP12V v2.91 SLI Ready CrossFire Ready 80 PLUS SILVER PSU
- ASUS DRW-24B1ST/BLK/B/AS Black SATA 24X DVD Burner
- Western Digital Caviar Black WD1002FAEX 1TB 7200 RPM SATA 6.0Gb/s 3.5" HDD
- AZZA Solano 1000 Black/Black Japanese SECC Steel/Metal mesh in front ATX Full Tower
- EVGA GeForce GTX 560 Ti FPB 1024 MB GDDR5 PCI-Express 2.0 Graphics Card
- Turtle Beach Montego DDL 7.1 Sound card
Any idea what could be wrong?

I'm not sure what it is, I could deal with it but I'm afraid one of these times I will go turn the computer on and it won't start up windows at all.
Anyone have any advice on what might be going on?

MSI P67A-C43 B3 won't POST with Full RAM Installed

Hello all,
I recently purchased the MSI P67A-C43 B3 mainboard as a custom build
and have been having trouble with it. I have 16GB of ram for this board
(4x 4GB) and when I have 8GB installed (slots 1 and 3 filled), it POSTS fine.
When I fill ALL the slots for 16GB total, the board won't POST and just
power cycles ON and OFF and ON and OFF, etc...
I have replaced the memory and the PSU and am about to replace the
mainboard, but wanted to ask if anyone might have a suggestion for
troubleshooting before I do that.
Here's what I'm running on the system:
mainboard: MSI P67A-C43 B3
proc: Intel Core i7-2600K 3.4Ghz Unlocked
proc cooler: Corsair Hydro H80 CPU Liquid Cooler
ram: Corsair High Perform Vengeance 4GB DDR3 1600Mhz2x4 (4 of these)
HDD: OCZ TECHNOLOGY 120GB VERTEX PLUS SSD and Seagate 1TB LP Serial ATA HD 5900/32MB/SATA-3G
CD Drive: Sony Optiarc 24X DVDRW SATA
video: EVGA GeForce GTX 560 Ti FPB 1024MB GDDR5 PCB PCIe
PSU: Thermaltake 750W Modular Power Supply. 80+ Bronze
case: Thermaltake Chaser MK-I Full Tower Gaming Case
OS: Microsoft Windows 7 Professional 64Bit DVD
Any ideas here would be greatly appreciated! Thanks!

OK, had some time to go test your suggestions here
These are the 1.5V Vengeance RAM Modules. Tried installing 2 of the RAM on slots 2 and 4 on their own. System Boots Fine.
Went into the BIOS and changed the voltage applied to the RAM modules from
AUTO to 1.575V. On AUTO it says is applying 1.5V to the 2x 4GB modules.
Installed the full 4x RAM on all slots... and the system just shuts down. Power cycling again.
What do you think here? Bad Motherboard? Can't think of anything else to try... totally stumped!
Thanks!

MSI P67a-c43 rev B3 temperature problem?

Hi, I've had my MSI P67a-c43 rev b3 since the spring of '11 and I've been very happy with it, haven't had any real problems with it at all actually.
Recently, I did however install a program to monitor the heat of my parts after a odd bluescreen, and I was frightened about what I found.
These temperatures were read after a intense gaming session (full load I guess)
SpeedFan: Temp2: 172 celsius
CPUID HWMonitor: TMPIN1: 127 celsius
None of the other temperatures are hotter than 40-50 celsius
After some googling around I found other users with the same MoBo having this issue, and it seems that the chipset which is located near the PCI-E port gets covered by the graphics card and either gets extremely hot or has a faulty temperature sensor.
As I said I've been using this rig since spring '11 and I haven't had any problems, I have only checked the temperatures the last few days however, so it's either been this hot for every day for almost two years or something bad has happened recently.
Wouldn't my MoBo have melted if a metal piece on it was over 100 degrees celsius, or atleast showed some issues?
Setup:
MSI P67a-c43 rev b3
Intel i5-2500k 3,3 GHz
Gigabyte GeForce GTX 460 1GB OC
Corsair Vengeance 2x4096 1600 MHz CL9
Win7 64-bit
I haven't overclocked or otherwise tampered with anything but installed these RAM's since I originally bought it.
So is there a heat problem or is there a malfunctioning sensor?

Try taking the door off and pointing a fan at the mainboard and see if the temp changes.

MSI P67A-C43 doesn't boot, code A3.

MSI P67A-C43 doesn't boot. Shows video card info, then beeps 3+1, shows 99, 98, A3 codes at lower right and freezes at A3. :(
Intel Core i5-2500K 3.3Ghz CPU, one Corsair XMS3 4GB PC10666 DDR3 memory at DIMM1, Galaxy GeForce GTX 460 1GB GDDR5 PCIe video, Seagate 1TB LP SATA-3G HD.
I did clear CMOS, didn't help.
What could I do, what to look at?
Thanks a lot.

Quote from: haasje_1 on 25-January-11, 22:16:48
I had the same problem with a P67A-C45 board. The problem is your videocard .I build my system with a Nvidia gt9500 and it didn't work. After a bit of testing (and also a new mainboard) I found out that after changing the videocard with an old ati card it does work). I send an e-mail to msi support i got a new biosversion for my mainboard (1.68) and everything works fine now.
Videocard it is. Thanks a lot, I'd never guess.
With simple ATI card id loads well.
So, is it going to work with GTX460 if I get latest BIOS?

Beeping on startup MSI P67A-C43 (b3)

plugged in 5 USB devices. on start up 5 short beeps and 1 loud beep all works great but windows 7 wont recognise USB mouse and need to be replugged than works like charm
any idea what meen that one LOUD beep???
MSI P67A-C43 (b3) BIOS Version V1.10, 3/31/2011
Intel(R) Core(TM) i3 2100 CPU @ 3.10GHz, 3100Mhz, 2Core(s), 4 Logical Processor(s)
Kingston 2x2GB DDR3-1333 (667MHz) Dual Channel 1 stick in first slot , 2 stick in third slot
MAXTOR STM3250310AS ATA Device 250GB
DVD/CD ATAPI iHAS124 B ATA Device
NVIDIA GeForce 8600 GT
ZITO 400W ATX 12V P4 AC INPUT:230V/115V AC 6A/10A 50Hz/60Hz Model:400D
is this configuration OK ? or something need to be replaced???
tnx in front

How many +12V continuous amps does that PSU supply? Recommend to contact MSI Tech Support & let them know of the mouse issue. They may have a UEFI/BIOS revision that will take care of that. http://support.msi.com
Quote
any idea what meen that one LOUD beep???
Added: The one loud beep is usually the POST beep.

MSI P67A-C43 (B3) USB not working but theres a twist! Help!

:lol_anim:I Have built a new rig with the MSI P67A-C43 (B3) Motherboard, 16GB DDR3 PC3-10600 1333MHz Memory (4GB x 4), Intel Core i5-2500K 3.3GHz 6M LGA1155 Processor, 550 Watt 80 PLUS Bronze Power Supply,24x DVDRW, 3.5" Internal Card Reader with 2 USB ports, 500GB 7200RPM 3.5" SATA Hard Drive(which i plan on upgrading just didnt want to waste money on the shitty HD they had.....
So down to the nitty gritty . My computer is running Windows 7 64 Bit, i have downloaded all of the updates and all of the Chip-set drivers, Bios, etc... i ran a system registry tool to clean up any errors in my registry and i have ALL of my drivers up to date.
I have my USB mouse and keyboard that connect fine and are recognized by my computer, sometimes they stop working and start back up within seconds but windows does display any type of error or disconnection "this may have been fixed due to the registry cleaner i used i haven't had any hiccups yet" so i have my USB mouse and USB keyboard working fine and dandy now i think. got a new headset and the windows finds the USB Headset and it works Perfectly fine. BUT and this is where my whole frustration comes out. Whenever i connect my I-Pod Touch, I-Pod Nano, My Cell phone to copy files to from my SD Card, or my External My Passport drive Windows says "USB Device was not recognized" notification and in the Device manager it shows the one device with a yellow exclamation point and says "Unknown Device" I have tried to uninstall the USB hubs and reinstalled them perfectly restarted windows, still non of the devices work. i have tried making sure that windows tries not to turn off the device to save power, when i say i have tried almost everything i mean everything that is related with USB Device not Recognized. So i do not know what to do now, i have contacted the Manufacturer and they don't know squat about it or what could be causing it. the only thing i can think of is there is some hardware maybe that is not compatible i do hear some beeps when i start up i will have to come back and update how many beeps" i saw another post that it means the motherboard is trying to tell me something maybe this could be the issue. but i have tried every single usb port and non of them Recognize the device but when i plus in my mouse and keyboard in diff ports they still work so i am a bit confused. my last step is to return the computer to the manufacturer for a replacement or repair w/e i do not want to do this cause this should be working. my friend has almost the exact same MB and equipment and his works fine so i am getting a little frustrated with the issue Someone Pls Help me out. And yes i have tried turning off the computer, unplugging it and pressing the power button, and waiting like 1 Hour etc and still nothing. Drivers are Up-to-Date and Mother board bios and chip-set drivers are Up-to-Date as well. I hope someone knows or has an answer to help me out!

Yes the Bios is Up-to-Date and they are not plugged into the Blue USB 3.0 ports(x2). oh and forgot to mention already did a clean install again of Windows 7 64bit and still nothing. Im also wondering if the power supply is enough?? maybe?

MSI P67A-C43 B3 Intel P67 - S/PDIF Coax Sound Issues

I recently put together a new PC with the MSI P67A-C43 B3 Intel P67 Mobo and am having some issues with the digital coax out to my digital 2.1 speakers. The speakers worked fine with my ancient SB card, so I know those aren't the issue. The issue I'm having is a clicking sound before and after sound almost as if the output is activating to play the sound and then deactivating when done. It stays on and plays fine when gaming, however it's very annoying when doing other windows tasks that involve sound as it's making the clicking sound before and after playing a sound. I opened a ticket with MSI support and they simply told me to RMA the board, but I don't feel like ripping everything apart and I really don't think it's a hardware defect. Has anyone else ran into this, or have any ideas on a fix?

This is a nasty little issue with the way Windows and Realtek work together with S/PDIF. I don't recall this issue with my sound card so I think it's probably Realtek that needs to fix this. The problem is that the digital S/PDIF port is closed after every access and it doesn't manage reopening the port correctly, it just opens when it's accessed again. This means that the port isn't ready in time to send any short sound transfers so they just make very ugly clicking noises. You can eliminate 99% of this by doing the following:
1. Open the control panel and select "Hardware and Sound"
2. Select "Change System Sounds"
3. Select the sound tab
4. Under the "Program Events:" list, select the following commands and set the "Sounds:" drop-down list to "None"
Under the "Windows" section:
Close Program
Maximize
Menu Command
Menu Pop-up
Minimize
Open Program
Program Error
Restore Down
Restore Up
Select
Show Toolbar Band
Under the "Windows Explorer" section:
Complete Navigation
Move Menu Item
Search Provided Discovered
Start Navigation
If you still hear some clicks then you may have some other programs that are sending short sound sequences to the port. Now that you've reminded me, I'm going to log a bug on this with MSI and anyone else with this problem should do the same. If they hear enough about it they might fix it the right way.
- D

Will a MSI GeForce GTX 660 work on my HP Pavilion p6-2102ed?

Hi all,
I have a HP Pavilion p6-2102ed with the H-CUPERTINO2-H61-uA TX (Cupertino2) motherboard.
I would like to upgrade it with a MSI GeForce GTX 660.
Now is the big question: will they both work together?
I already read something about the powersupply. The videocard requires a six-pinned plug connected to a powersupply, which the p6-2102ed doesn't have.
1: How do I solve this? Do I have to buy an external powersupply? If so, what powersupply do you reccomend? Or can I just buy a powercable (with six pins) and connect it to the powersupply built in the p6-2102ed?
2: I read the MSI GeForce GTX 660 measures 260 mm long. I think it will fit in the case. So that won't be the problem I think.
3: Will the Bios accept the new videocard? Or do I have to adjust some settings in the Bios?
These are all of the issues that I can think of right now.
Please correct me if something I wrote is wrong and if you know more important information, please tell me!
Thank you for helping me.

Hi seb_asian!: off the top of my head I can think of my ATI Radeon HD5570, the GeForce 240, the ATI Radeon 6570 they all will give you better performance won't either drain the PSU nor the electric bill either & they won't force your box to deploy extra fans trying to cool it down.
OK other last generation cards will give you better performance on the one hand but you may not be able to play the current games either which takes advantage of whatever state-of-the-art technology the card may contain
& slso they'll will run hotter because everything is a bit bigger transistor wise (a 50nm card vs a 30nm model as an example)
good luck
hope this helps & enlightens you
spacechild

MSI P67A-C43 B3 and MSI GeForce GTX 660 2GB GDDR5 Twin Frozr III N660 TF 2GD5/O

Similar Messages

Maybe you are looking for