Multicast VPN Extranet Support doesn't work after reload

Hi!
We have Cat6500 with configured Multicast VPN Extranet Support feature. After reload of the 6500 customers in the receive MVPN cannot get mcast stream. We connect test device into source MVPN on that 6500 - everything is OK, mcast stream is available.
Workaround is "no mls ip multicast/mls ip multicast". After these commands mcast in the receive MVPN works fine.
IOS 12.2 SXJ2
Looks like a bug. We have several Cat6500 but only two of them have this issue.
Does anybody faced with such trouble?

Similar Messages

TS4268 FaceTime doesn't work after upgrade to ISO 6.0.1, apple support team has sent an auto reply that doesn't help .... Any suggestion will be appreciated

FaceTime doesn't work after upgrade to ISO 6.0.1, apple support team has sent an auto reply that doesn't help .... Any suggestion will be appreciated

Hi AnaMusic,
It was working perfectly before the upgrade to ISO 6.0.1, but now I can't log in using my apple ID ... I have tried all suggestion from Tom but nothing does work. I keep getting the message "FaceTime can't log in, check your network" is nothing wrong with my network everything else works fine, I can log in into FaceTime using my IPad 2 and my apple ID.
I'm currently working in Korea, but I bought the IPad in Australia,
Regards,
Namur

[Solved] Network doesn't work after hibernate?

Hello! This is my first legit Linux install so excuse me if I'm a bit slow. I installed Arch last night and everything went smoothly. However, after I tested out hibernate on my machine, the network doesn't seem to work. Just prior to the hibernate, I installed Pidgin and Skype but they worked alright, so I think that the hibernate caused a problem on eth0.
I have an Asus P8Z68-V Pro motherboard with an Intel 82579V Gigabit Ethernet Controller that's using the e1000e driver. Running "dmesg | grep e1000e" says that it is up.
I'm not entirely clear here, but from reading, I think that I have several ways of connecting to the network, including network, dhcpcd, networkmanager, and wicd. I am using wicd so I did the following (or at least I think I am only using wicd):
#rc.d stop network
#rc.d stop dhcpcd
#rc.d stop networkmanager
Similarly, I put a ! in front of network in rc.conf:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# DAEMON_LOCALE: If set to 'yes', use $LOCALE as the locale during daemon
# startup and during the boot process. If set to 'no', the C locale is used.
# HARDWARECLOCK: set to "", "UTC" or "localtime", any other value will result
# in the hardware clock being left untouched (useful for virtualization)
# Note: Using "localtime" is discouraged, using "" makes hwclock fall back
# to the value in /var/lib/hwclock/adjfile
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# Note: if unset, the value in /etc/localtime is used unchanged
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.UTF-8"
DAEMON_LOCALE="no"
HARDWARECLOCK="UTC"
TIMEZONE="America/New_York"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MODULES: Modules to load at boot-up. Blacklisting is no longer supported.
# Replace every !module by an entry as on the following line in a file in
# /etc/modprobe.d:
# blacklist module
# See "man modprobe.conf" for details.
MODULES=()
# Udev settle timeout (default to 30)
UDEV_TIMEOUT=30
# Scan for FakeRAID (dmraid) Volumes at startup
USEDMRAID="no"
# Scan for BTRFS volumes at startup
USEBTRFS="no"
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="Vicious"
# Use 'ip addr' or 'ls /sys/class/net/' to see all available interfaces.
# Wired network setup
# - interface: name of device (required)
# - address: IP address (leave blank for DHCP)
# - netmask: subnet mask (ignored for DHCP) (optional, defaults to 255.255.255.0)
# - broadcast: broadcast address (ignored for DHCP) (optional)
# - gateway: default route (ignored for DHCP)
# Static IP example
# interface=eth0
# address=192.168.0.2
# netmask=255.255.255.0
# broadcast=192.168.0.255
# gateway=192.168.0.1
# DHCP example
# interface=eth0
# address=
# netmask=
# gateway=
interface=eth0
address=
netmask=
broadcast=
gateway=
# Setting this to "yes" will skip network shutdown.
# This is required if your root device is on NFS.
NETWORK_PERSIST="no"
# Enable these netcfg profiles at boot-up. These are useful if you happen to
# need more advanced network features than the simple network service
# supports, such as multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
# If something other takes care of your hardware clock (ntpd, dual-boot...)
# you should disable 'hwclock' here.
DAEMONS=(hwclock syslog-ng dbus !network netfs crond wicd)
Restarting eth0 through wicd-cli still did not work. I also tried resuscitating the network via instructions on the configure network page before trying to focus solely on wicd.
I found a few similar problems on the forums by searching "wicd hibernate" and tried several solutions but they did not work. Several problems seem to be that the network doesn't work after a suspend because I guess the stuff in RAM did not get saved? But people were able to restart the network by running "/usr/lib/wicd/autoconnect.py" and I wasn't able to get this to work. As a final effort, I added "resume" into mkinitcpio.conf and placed the machine into sleep again to see if it may magically reset something but of course this did not happen .
mkinitcpio.conf:
# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run. Advanced users may wish to specify all system modules
# in this array. For instance:
# MODULES="piix ide_disk reiserfs"
MODULES=""
# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image. This is run first, so it may be used to
# override the actual binaries used in a given hook.
# (Existing files are NOT overwritten if already added)
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=""
# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way. This is useful for config files.
# Some users may wish to include modprobe.conf for custom module options
# like so:
# FILES="/etc/modprobe.d/modprobe.conf"
FILES=""
# HOOKS
# This is the most important setting in this file. The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
## This setup specifies all modules in the MODULES setting above.
## No raid, lvm2, or encrypted root is needed.
# HOOKS="base"
## This setup will autodetect all modules for your system and should
## work as a sane default
# HOOKS="base udev autodetect pata scsi sata filesystems"
## This is identical to the above, except the old ide subsystem is
## used for IDE devices instead of the new pata subsystem.
# HOOKS="base udev autodetect ide scsi sata filesystems"
## This setup will generate a 'full' image which supports most systems.
## No autodetection is done.
# HOOKS="base udev pata scsi sata usb filesystems"
## This setup assembles a pata mdadm array with an encrypted root FS.
## Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
# HOOKS="base udev pata mdadm encrypt filesystems"
## This setup loads an lvm2 volume group on a usb device.
# HOOKS="base udev usb lvm2 filesystems"
HOOKS="base udev autodetect pata scsi sata resume filesystems usbinput"
# COMPRESSION
# Use this to compress the initramfs image. With kernels earlier than
# 2.6.30, only gzip is supported, which is also the default. Newer kernels
# support gzip, bzip2 and lzma. Kernels 2.6.38 and later support xz
# compression.
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"
# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=""
Not sure if my fstab.conf is useful but if this has something to do with settings getting "lost" in swap, here it is. Linux is on an SSD and HDD (sda and sdc) and Windows 7 is on a HDD (sdb).
fstab.conf:
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
none /tmp tmpfs nodev,nosuid,noatime,size=2000M,mode=1777 0 0
/dev/sda1 / ext4 defaults,noatime,discard 0 1
/dev/sda2 /home ext4 defaults,noatime,discard 0 2
/dev/sdc1 /boot ext4 defaults 0 1
/dev/sdc2 /var ext4 defaults 0 0
/dev/sdc3 swap swap defaults 0 0
/dev/sdc4 /media/data ext4 defaults 0 0
shm /dev/shm tmpfs nodev,nosuid,size=10G 0 0
Is wicd causing these problems or did I configure something else improperly? Would appreciate any help to get eth0 up again!
Last edited by TheBigCow7 (2011-09-13 17:57:20)

Ok, I think I've made some progress! Hibernate definitely affects my network connection. Could this be a kernel 3.0 problem?
I noticed that ifconfig showed eth0 without an inet addr, just an inet6 addr for the longest time. e1000e seemed to be loading up ok. I'm not certain here, but I think that meant the dhcp settings didn't stick, or something along those lines.
Trying to use dhcpcd like the instructions here did not work. By some chance, one attempt did work and while it did, I downloaded and installed dhclient. After that one successful attempt, renewing the DHCP lease via dhcpcd did not work again.
Luckily though, I found that running "dhclient eth0" worked. My DHCP settings seemed to have somehow gotten messed up after my initial, problematic hibernate to the point where none would stick, even after a reboot. Manually typing in "dhclient eth0" would get eth0 working, so I decided to add it to the bottom of /etc/rc.local, like in the example on the networking page.
Now, eth0 works after a boot. However, after the daemons load up during the boot process, my computer takes a long time to get to the login prompt (this is relatively speaking, since I am on a SSD and the boot process used to be blazing fast before). I'm pretty sure it's because I added "dhclient eth0" to /etc/rc.local.
I should say that even with these changes, after a hibernate, my eth0 still does not work and if it weren't for the edit to /etc/rc.local, eth0's inet settings would still not stick after a reboot (that is to say, the hibernate does do something to my network settings).
Is this the correct/most efficient way to fix my DHCP problem? Can I fix my "eth0 after hibernate" issue? Also, can I make my DHCP settings boot up without changes to /etc/rc.local so that I can get a fast boot again (still not sure how it was able to work before without my edit)?

Sirius Internet Radio doesn't work after Snow Leopard

Sirius Internet Radio doesn't work after I installed Snow Leopard. It works on my Firefox. I emptied the cache on my Safari, but still nothing. Any solutions?

The reason why Sirius Radio online won't work with Safari anymore is because Sirius radio online is only supported by a 32-bit browser. Snow Leopard and all its applications are 64-bit. The best solution is to use firefox. If you still insist on using safari..... Go to adobe.com reinstall adobe flash player. Install/update Flip4Mac. Go to setting for Flip4Mac and check off all the options under the browser tab. Then when you go into Sirius Radio online, you will get an error message, just click okay. Then when you click a station, a quicktime player will come up and you will be able to listen to sirius online radio.
[email protected]

My E-Mail Accounts Pop3 doesn´t work after update Lion

My E-Mail Accounts Pop3 doesn´t work after update Lion.

Same here,and Apple support did not have a solution!!

Stand-by button on Cinema HD display doesn't work after Mountain Lion upgrade

Hi,
After I upgraded my Mac mini (spring '09) to Mountain Lion it appears that the buttons on the side of my Cinema HD display doesn't work. There is a setting in sys preferences that should put the Mac in stand-by when the power button is pressed. This doesn't work after I upgraded to OSX 10.8 Mountain Lion.
Does anyone have similar experience. Anyway to fix it?
Thanks,
Henrik

Have done some further investigating (to no avail). The TV is displaying in my system Info as follows:
Intel HD Graphics 3000:
Chipset Model: Intel HD Graphics 3000
Type: GPU
Bus: Built-In
VRAM (Total): 384 MB
Vendor: Intel (0x8086)
Device ID: 0x0116
Revision ID: 0x0009
Displays:
Color LCD:
Display Type: LCD
Resolution: 1440 x 900
Pixel Depth: 32-Bit Color (ARGB8888)
Main Display: Yes
Mirror: Off
Online: Yes
Built-In: Yes
Connection Type: DisplayPort
TOSHIBA-TV:
Resolution: 1920 x 1080 @ 60 Hz
Pixel Depth: 32-Bit Color (ARGB8888)
Mirror: Off
Online: Yes
Rotation: Supported
Television: Yes
But nothing on the screen.
Does anyone know if Apple have banned certain screens????

IPhoto 8.1.2 doesn't work after reinstalled the OS 10.6.8?

iPhoto 8.1.2 doesn't work after reinstalled OS 10.6.8?

To re-install iPhoto
1. Put the iPhoto.app in the trash (Drag it from your Applications Folder to the trash)
2. Download it from the App Store to reinstall It's on your Purchases List* there.
For older versions that have been installed from Disk you'll need these additional steps:
2a: On 10.5: Go to HD/Library/Receipts and remove any pkg file there with iPhoto in the name.
2b: On 10.6: Those receipts may be found as follows: In the Finder use the Go menu and select Go To Folder. In the resulting window type
/var/db/receipts/
2c: on 10.7 or later they're at
/private/var/db/receipts
A Finder Window will open at that location and you can remove the iPhoto pkg files.
3. Re-install.
If you purchased an iLife Disk, then iPhoto is on it.
If iPhoto was installed on your Mac when you go it then it’s on the System Restore disks that came with your Mac. Insert the first one and opt to ‘Install Bundled Applications Only.
*Sometimes iPhoto is not visible on the Purchases List. it may be hidden. See this article for details on how to unhide it.
http://support.apple.com/kb/HT4928
One question often asked: Will I lose my Photos if I reinstall?
iPhoto the application and the iPhoto Library are two different parts of the iPhoto programme. So, reinstalling the app should not affect the Library. BUT you should always have a back up before doing this kind of work. Always.

M3800 Developer Edition: wifi doesn't work after sleep

I have an M3800 Developer Edition (2015 model). Ubuntu is factory-installed 14.04, with hardware enablement stack installed. Recently (past 1-2 weeks) wifi doesn't work after sleep (lid closed or open doesn't matter), and only rebooting gets in back. Tried rmmod and modprobe with no success. Has anyone else seen this, and/or are you aware of any open bug(s) for this?
Relevant ouput:
lsmod when problem exists:
iwlmvm                217725 0
mac80211              652718 1 iwlmvm
iwlwifi               179412 1 iwlmvm
cfg80211              494362 3 iwlwifi,mac80211,iwlmvm
rfkill list when problem exists:
1: phy0: Wireless LAN
        Soft blocked: no
        Hard blocked: no
3: hci0: Bluetooth
        Soft blocked: no
        Hard blocked: no
rmmod the above, then modprobe iwlwifi. Does not fix problem, only rebooting does:
May 4 08:23:14 jonathan-m3800 kernel: [69089.189614] cfg80211: Calling CRDA to update world regulatory domain
May 4 08:23:14 jonathan-m3800 kernel: [69089.192181] cfg80211: World regulatory domain updated:
May 4 08:23:14 jonathan-m3800 kernel: [69089.192184] cfg80211: DFS Master region: unset
May 4 08:23:14 jonathan-m3800 kernel: [69089.192185] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
May 4 08:23:14 jonathan-m3800 kernel: [69089.192187] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
May 4 08:23:14 jonathan-m3800 kernel: [69089.192188] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
May 4 08:23:14 jonathan-m3800 kernel: [69089.192189] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
May 4 08:23:14 jonathan-m3800 kernel: [69089.192190] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
May 4 08:23:14 jonathan-m3800 kernel: [69089.192191] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
May 4 08:23:14 jonathan-m3800 kernel: [69089.204141] Intel(R) Wireless WiFi driver for Linux, in-tree:
May 4 08:23:14 jonathan-m3800 kernel: [69089.204143] Copyright(c) 2003- 2014 Intel Corporation
May 4 08:23:14 jonathan-m3800 kernel: [69089.204414] iwlwifi 0000:06:00.0: irq 48 for MSI/MSI-X
May 4 08:23:14 jonathan-m3800 kernel: [69089.204904] iwlwifi 0000:06:00.0: loaded firmware version 25.228.9.0 op_mode iwlmvm
May 4 08:23:14 jonathan-m3800 kernel: [69089.207709] iwlwifi 0000:06:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144
May 4 08:23:14 jonathan-m3800 kernel: [69089.207790] iwlwifi 0000:06:00.0: L1 Enabled - LTR Enabled
May 4 08:23:14 jonathan-m3800 kernel: [69089.208150] iwlwifi 0000:06:00.0: L1 Enabled - LTR Enabled
May 4 08:23:14 jonathan-m3800 kernel: [69089.392408] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
May 4 08:23:14 jonathan-m3800 NetworkManager[901]:    SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1c.2/0000:06:00.0/net/wlan0, iface: wlan0)
May 4 08:23:14 jonathan-m3800 NetworkManager[901]:    SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1c.2/0000:06:00.0/net/wlan0, iface: wlan0): no ifupdown configuration found.
May 4 08:23:14 jonathan-m3800 NetworkManager[901]: <info> (wlan0): using nl80211 for WiFi device control
May 4 08:23:14 jonathan-m3800 NetworkManager[901]: <info> (wlan0): driver supports Access Point (AP) mode
May 4 08:23:14 jonathan-m3800 NetworkManager[901]: <info> (wlan0): new 802.11 WiFi device (driver: 'iwlwifi' ifindex: 4)
May 4 08:23:14 jonathan-m3800 NetworkManager[901]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/2
May 4 08:23:14 jonathan-m3800 NetworkManager[901]: <info> rfkill5: found WiFi radio killswitch (at /sys/devices/pci0000:00/0000:00:1c.2/0000:06:00.0/ieee80211/phy0/rfkill5) (driver iwlwifi)
May 4 08:23:16 jonathan-m3800 ModemManager[852]: <warn> Couldn't find support for device at '/sys/devices/pci0000:00/0000:00:1c.2/0000:06:00.0': not supported by any plugin
lspci:
06:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b)
After reboot:
lsmod |grep -i iwl:
iwlmvm                217725 0
mac80211              652718 1 iwlmvm
iwlwifi               179412 1 iwlmvm
cfg80211              494362 3 iwlwifi,mac80211,iwlmvm
rfkill list after reboot:
0: nfc0: NFC
        Soft blocked: no
        Hard blocked: no
1: phy0: Wireless LAN
        Soft blocked: no
        Hard blocked: no
2: hci0: Bluetooth
        Soft blocked: no
        Hard blocked: no

Wi-Fi still not reconnecting after sleep
http://forums.macrumors.com/showthread.php?t=1229591

ZawgyiOne Font doesn't work after updating to iOS 7.1, please advice

ZawgyiOne Font doesn't work after updating to iOS 7.1, please advice

hi Mr.Sianpu
nice to know you, my name Kiemtheng from Cambodia, i got a problem with Khmer Unicode font at my ipad which i just update from IOS 7.0.1 to ISO 7.1.1 , It not support with Khmer font which used to appear at the old version , the problem happen as the same Lian Tuang Question, and can you tell me how to fix this problem , hope to hear a good new from your, for khmer unicode font which support with Nokora and Battombong
http://adkhmer.com/app/iphone/font_khmer_ios7_no_jailbreak/Nokora.mobileconfig
https://docs.google.com/file/d/0B8798SqaxK-JS1B5T3hjNkJPQUE/edit?pli=1
thanks

ITunes doesn't work after upgrade to iOS 6

iTunes doesn't work after upgrade to iOS 6. The white screen with gray tape above appears, and nothing more happens. Reinstalling/restoring iOS doesn't help. I have contacted support team in my country (Russia) by phone, but they could not solve the problem. Is there downgrade to iOS 5.1.1 available?

What printer are you using? Is it listed here:
http://support.apple.com/kb/ht4356

App store doesn't work after iOS6

App Store doesn't work after ios6. Re-booting doesn't work. Suggestions please.

I have the same problem with my New iPad.
It was fine until this afternoon when I upgraded to ios6.
I don't have the wifi issues that others have reported but my AppStore doesn't work anymore.
It's just the AppStore that won't work.
Though Purchased and Updates looks OK, "Featured," "Charts" and search all return no results - just a big gray screen in the middle. I've been walked thru a Restore by Support but nothing's worked so far. I've tried logging off and logging back on.
From what I can tell, everything else (iTunes, apps, etc) look ok.
Any other suggestions?

Dreamweaver doesn't work after Yosemite upgrade.

Dreamweaver doesn't work after Yosemite upgrade, it asks to install Java Runtime SE 6, I've tried that, I've also installed latest Java and it still won't boot, keeps asking for for Java Runtime SE 6

You need http://support.apple.com/kb/DL1572
27" i7 iMac (Mid 2011) refurb, OS X Yo (10.10.1), Mavs, ML & SL, G4 450 MP w/10.5 & 9.2.2

My MacBook adaptor stopped working so I used my roommates. Now hers doesn't work after just one day. What happened?

My MacBook adaptor stopped working so I used my roommates. Now hers doesn't work after just one day. What happened?

Hello, cherilyn.
Thank you for visiting Apple Support Communities.
I understand that a couple MagSafe adapters will no longer charger a couple MacBooks. Here are the best troubleshooting steps to go through when experiencing this issue.
Apple Portables: Troubleshooting MagSafe adapters
Cheers,
Jason H.

IMac - Display doesn´t work after restart

My iMac 21 Display doesn´t work after restart. If I turn it off and 1 hour later I want use it again the iMac shows the white screen with the mac logo and then the display goes off. I connected an external display to check if the iMac was ON and with the external display I can login and do everything but the iMac Display doesn´t work .
If I turn it off and wait 3 or 4 hours and then turn it back on the display works OK.
This is very strange behavior I have spent hours and hours trying to fine the solution or a similar issue but nothing so I am looking help here at apple.com
BTW When I bougth the iMac 21 there were some spots over the display so the display was replaced by the provider. The warranty has expired by now.

To tell you the truth, I don't know if they have to repalce the LCD panel or what they do for a bad backlight. In this reality of block or assembly replacement it probably involves repalcing the panel and not the backlight component. Don't know what it would cost. You'd have to ask that of a service center.

Touch ID doesn't work after ios 7.1.1 update

Touch id doesn't work after ios 7.1.1 update..
Why????

After IOS update, you first have to use passcode.
Passcode is needed when
After restarting your iPhone 5s
When more than 48 hours have elapsed from the last time you unlocked your iPhone 5s
To enter the Touch ID & Passcode setting

Multicast VPN Extranet Support doesn't work after reload

Similar Messages

Maybe you are looking for