Multiple IPSEC tunnels on ASA 5505

Configuring Multiple IPSEC tunnels on ASA 5505
Hi,
I need to configure 2 diffrent type of IPSEC tunnels on my ASA 5505. 1st one is static ipsec tunnel already configured between HO to site A and 2nd one is dynamic to be configure between HO to site B since site B does not have static IP so I have to configure dynamic ipsec vpn.
I have following clarification
1. After configuring dynamic ipsec Is my existing static ipsec tunnel will work simultenously?
2. can I apply different crypmap on the same outside interface? if not then what setting i need to do to make this work?
3. Do i need to create 1 more Nat0 or can i add in existing ACL which i have already created for previous.
kindly help me on this
Thanks in advance
Subhan Shaikh
France Telecom

Similar Messages

How to set up Split Tunneling on ASA 5505

Good Morning,
I have an ASA 5505 with security plus licensing. I need to set up split tunneling on the ASA and not sure how. I am very new to Cisco but am learning quickly. What I want to accomplish, if possible is to send all traffic to our corporate web site (static ip address) straight out to the internet and all other traffic to go though the tunnel as normal. Basically we have a remote office that is using a local ISP to provide internet service. IF our connection at the main office goes down, we want the branch office to still be able to get to our corporate website without having to unplug cables and connect their computer directly to the local ISP modem. Any help with be greatly appriciated. Thanks in advance. Below is a copy of our current config.
ASA Version 7.2(4)
hostname TESTvpn
enable password rBtWtkaB8W1R3ub8 encrypted
passwd rBtWtkaB8W1R3ub8 encrypted
names
name 10.0.0.0 Corp_LAN
name 192.168.64.0 Corp_Voice
name 172.31.155.0 TESTvpn
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Vlan3
nameif Corp_Voice
security-level 100
ip address 172.30.155.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 3
ftp mode passive
object-group network SunVoyager
network-object host 64.70.8.160
network-object host 64.70.8.242
object-group network Corp_Networks
network-object Corp_LAN 255.0.0.0
network-object Corp_Voice 255.255.255.0
access-list outside_access_in extended permit icmp any any unreachable
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended permit icmp any any time-exceeded
access-list inside_access_in extended permit ip TESTvpn 255.255.255.0 any
access-list inside_access_in extended permit icmp TESTvpn 255.255.255.0 any
access-list Corp_Voice_access_in extended permit ip 172.30.155.0 255.255.255.0 any
access-list Corp_Voice_access_in extended permit icmp 172.30.155.0 255.255.255.0 any
access-list VPN extended deny ip TESTvpn 255.255.255.0 object-group SunVoyager
access-list VPN extended permit ip TESTvpn 255.255.255.0 any
access-list VPN extended permit ip 172.30.155.0 255.255.255.0 any
access-list data-vpn extended permit ip TESTvpn 255.255.255.0 any
access-list voice-vpn extended permit ip 172.30.155.0 255.255.255.0 any
access-list all-vpn extended permit ip TESTvpn 255.255.255.0 any
access-list all-vpn extended permit ip 172.30.155.0 255.255.255.0 any
pager lines 24
logging enable
logging buffer-size 10000
logging monitor debugging
logging buffered informational
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu Corp_Voice 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list data-vpn
nat (inside) 1 TESTvpn 255.255.255.0
nat (inside) 1 0.0.0.0 0.0.0.0
nat (Corp_Voice) 0 access-list voice-vpn
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
access-group Corp_Voice_access_in in interface Corp_Voice
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http 192.168.1.0 255.255.255.0 inside
http TESTvpn 255.255.255.0 inside
http Corp_LAN 255.0.0.0 inside
http 65.170.136.64 255.255.255.224 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set VPN esp-3des esp-md5-hmac
crypto map outside_map 1 match address VPN
crypto map outside_map 1 set peer 66.170.136.65
crypto map outside_map 1 set transform-set VPN
crypto map outside_map interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 28800
telnet timeout 5
ssh Corp_LAN 255.0.0.0 inside
ssh TESTvpn 255.255.255.0 inside
ssh 65.170.136.64 255.255.255.224 outside
ssh timeout 20
console timeout 0
management-access inside
dhcpd auto_config outside
dhcpd option 150 ip 192.168.64.4 192.168.64.3
dhcpd address 192.168.1.2-192.168.1.33 inside
dhcpd dns 10.10.10.7 10.10.10.44 interface inside
dhcpd domain sun.ins interface inside
dhcpd enable inside
dhcpd address 172.30.155.10-172.30.155.30 Corp_Voice
dhcpd dns 10.10.10.7 10.10.10.44 interface Corp_Voice
dhcpd domain sun.ins interface Corp_Voice
dhcpd enable Corp_Voice
username admin password kM12Q.ZBqkvh2p03 encrypted privilege 15
tunnel-group 66.170.136.65 type ipsec-l2l
tunnel-group 66.170.136.65 ipsec-attributes
pre-shared-key *
prompt hostname context
Cryptochecksum:953e50e9cbc02e1b264830dab4a3f2bd
: end

So I tried to use the exclude way that you suggested. Here is my new config. It is still not working. The address I put in for the excluded list was 4.2.2.2 and when I do a trace route to it from the computer, it still goes though the vpn to the main office and out the switch at the main office and not from the local isp. Any other suggestions?
hostname TESTvpn
domain-name default.domain.invalid
enable password rBtWtkaB8W1R3ub8 encrypted
passwd rBtWtkaB8W1R3ub8 encrypted
names
name 10.0.0.0 Corp_LAN
name 192.168.64.0 Corp_Voice
name 172.31.155.0 TESTvpn
interface Vlan1
nameif inside
security-level 100
ip address 172.31.155.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Vlan3
nameif Corp_Voice
security-level 100
ip address 172.30.155.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 3
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
object-group network SunVoyager
network-object host 64.70.8.160
network-object host 64.70.8.242
object-group network Corp_Networks
network-object Corp_LAN 255.0.0.0
network-object Corp_Voice 255.255.255.0
access-list outside_access_in extended permit icmp any any unreachable
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended permit icmp any any time-exceeded
access-list inside_access_in extended permit ip TESTvpn 255.255.255.0 any
access-list inside_access_in extended permit icmp TESTvpn 255.255.255.0 any
access-list Corp_Voice_access_in extended permit ip 172.30.155.0 255.255.255.0 a
ny
access-list Corp_Voice_access_in extended permit icmp 172.30.155.0 255.255.255.0
any
access-list VPN extended deny ip TESTvpn 255.255.255.0 object-group SunVoyager
access-list VPN extended permit ip TESTvpn 255.255.255.0 any
access-list VPN extended permit ip 172.30.155.0 255.255.255.0 any
access-list data-vpn extended permit ip TESTvpn 255.255.255.0 any
access-list voice-vpn extended permit ip 172.30.155.0 255.255.255.0 any
access-list all-vpn extended permit ip TESTvpn 255.255.255.0 any
access-list all-vpn extended permit ip 172.30.155.0 255.255.255.0 any
access-list TEST standard permit host 4.2.2.2
pager lines 24
logging enable
logging buffer-size 10000
logging monitor debugging
logging buffered informational
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu Corp_Voice 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list data-vpn
nat (inside) 1 TESTvpn 255.255.255.0
nat (Corp_Voice) 0 access-list voice-vpn
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
access-group Corp_Voice_access_in in interface Corp_Voice
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http TESTvpn 255.255.255.0 inside
http Corp_LAN 255.0.0.0 inside
http 65.170.136.64 255.255.255.224 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set VPN esp-3des esp-md5-hmac
crypto map outside_map 1 match address VPN
crypto map outside_map 1 set peer 66.170.136.65
crypto map outside_map 1 set transform-set VPN
crypto map outside_map interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 28800
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh Corp_LAN 255.0.0.0 inside
ssh TESTvpn 255.255.255.0 inside
ssh 65.170.136.64 255.255.255.224 outside
ssh timeout 20
console timeout 0
management-access inside
dhcpd auto_config outside
dhcpd option 150 ip 192.168.64.4 192.168.64.3
dhcpd address 172.31.155.10-172.31.155.30 inside
dhcpd dns 10.10.10.7 10.10.10.44 interface inside
dhcpd domain sun.ins interface inside
dhcpd enable inside
dhcpd address 172.30.155.10-172.30.155.30 Corp_Voice
dhcpd dns 10.10.10.7 10.10.10.44 interface Corp_Voice
dhcpd domain sun.ins interface Corp_Voice
dhcpd enable Corp_Voice
group-policy DfltGrpPolicy attributes
banner none
wins-server none
dns-server none
dhcp-network-scope none
vpn-access-hours none
vpn-simultaneous-logins 3
vpn-idle-timeout 30
vpn-session-timeout none
vpn-filter none
vpn-tunnel-protocol IPSec l2tp-ipsec webvpn
password-storage disable
ip-comp disable
re-xauth disable
group-lock none
pfs disable
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy excludespecified
split-tunnel-network-list value TEST
default-domain none
split-dns none
intercept-dhcp 255.255.255.255 disable
secure-unit-authentication disable
user-authentication disable
user-authentication-idle-timeout 30
ip-phone-bypass disable
leap-bypass disable
nem disable
backup-servers keep-client-config
msie-proxy server none
msie-proxy method no-modify
msie-proxy except-list none
msie-proxy local-bypass disable
nac disable
nac-sq-period 300
nac-reval-period 36000
nac-default-acl none
address-pools none
smartcard-removal-disconnect enable
client-firewall none
client-access-rule none
webvpn
functions url-entry
html-content-filter none
homepage none
keep-alive-ignore 4
http-comp gzip
filter none
url-list none
customization value DfltCustomization
port-forward none
port-forward-name value Application Access
sso-server none
deny-message value Login was successful, but because certain criteria have not
been met or due to some specific group policy, you do not have permission to us
e any of the VPN features. Contact your IT administrator for more information
svc none
svc keep-installer installed
svc keepalive none
svc rekey time none
svc rekey method none
svc dpd-interval client none
svc dpd-interval gateway none
svc compression deflate
username admin password kM12Q.ZBqkvh2p03 encrypted privilege 15
tunnel-group 66.170.136.65 type ipsec-l2l
tunnel-group 66.170.136.65 ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:8b3caaecf2a0dec7334633888081c367
: end

How many IPSec Tunnels an ASA 5500 series supports

Hi All,
I tried looking in ASA documentations but unable to find out that how many IPSec Tunnels can be terminated to an ASA cluster. I have 5545 running only two IPSec Tunnels so far but need to terminate 18 sites all up and would like to confirm how many tunnels we could terminate? Is there a limitaion to it?
Thanks heaps
Shan

Yes, there is a limit. But its far away from your requirement. On the 5545-X you can terminate 2500 VPN-Peers:
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/at_a_glance_c45-701635.pdf
Sent from Cisco Technical Support iPad App

Creating Second tunnel in asa 5505 to accept from PIX506

One Cisco PIX at datacentre(remote) and one asa5505 and one PIX 506E at my office both are creating VPN to data centre but now i need to access asa n/w from pix n/w which are in the same LAN..

You should be able to implement policy NAT on one or both sides to accomplish what you want to do.
- James

AP registration over IPSEC Tunnel(ASA)

Guys,
I have my WAP sitting behind ASA and have ipsec tunnel between ASA and router.below is the topology:-
WAP>>ASA<<< IPSEC TUNNEL>>> Router<<<WLC
Recently we have replaced router with ASA 5505 for security reasons and since then WAP is not able to registered to WLC. we have VPN tunnel up and working. Even WAP is able to ping to WLC ip address.
Do we have any special configuration in my ASA considering my above topology. I can confirm that capwap and lwap ports are opened in asa.
Please let me know if some one has faced this issue before.

Hi,
I hope you have already allowed the below mentioned ports as per your requirement.
You must enable these ports:
Enable these UDP ports for LWAPP traffic:
Data - 12222
Control - 12223
Enable these UDP ports for mobility traffic:
16666 - 16666
16667 - 16667
Enable UDP ports 5246 and 5247 for CAPWAP traffic.
TCP 161 and 162 for SNMP (for the Wireless Control System [WCS])
These ports are optional (depending on your requirements):
UDP 69 for TFTP
TCP 80 and/or 443 for HTTP or HTTPS for GUI access
TCP 23 and/or 22 for Telnet or SSH for CLI access
Also if it goes over the IPSec VPN, MTU size for the path between AP and WLC should be of 1500, if it has the lesser MTU, then communication fails.
Can you get me your WLC and ASA OS versions?
Regards
Karthik

ASA 5505 rookie - can't ping remote site or vice versa

Hi, I'm trying to setup an ipsec from an ASA 5505 (8.4) to a Sophos UTM (9.2)
Internet etc is up and accessible. Ipsec tunnel is up also but I can't pass traffic through it.
I get this message in the logs:
3
Aug 05 2014
22:38:52
81.111.111.156
82.222.222.38
Deny inbound protocol 50 src outside:81.111.111.156 dst outside:82.222.222.38
SITE A (ASA 5505) = 82.222.222.38
SITE B (UTM 9) = 81.111.111.156
Any pointers would be good as this is the first time I've tried this. Thank you.
Running config below:
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
description Zen Internet
nameif outside
security-level 0
pppoe client vpdn group Zen
ip address 82.222.222.38 255.255.255.255 pppoe setroute
boot system disk0:/asa922-k8.bin
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 8.8.8.8
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network MY-LAN
subnet 192.168.1.0 255.255.255.0
object network THIER-LAN
subnet 192.168.30.0 255.255.255.0
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network NETWORK_OBJ_192.168.30.0_24
subnet 192.168.30.0 255.255.255.0
object network THIER_VPN
host 81.111.111.156
description THIER VPN
object service Sophos_Admin
service tcp destination eq 4444
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
protocol-object esp
object-group protocol DM_INLINE_PROTOCOL_2
protocol-object ip
protocol-object icmp
protocol-object esp
object-group protocol DM_INLINE_PROTOCOL_3
protocol-object ip
protocol-object icmp
protocol-object esp
object-group service DM_INLINE_SERVICE_1
service-object icmp
service-object udp destination eq domain
service-object object Sophos_Admin
service-object tcp destination eq www
service-object tcp destination eq https
service-object esp
object-group service DM_INLINE_SERVICE_2
service-object icmp
service-object object Sophos_Admin
service-object esp
service-object icmp echo-reply
object-group service DM_INLINE_SERVICE_3
service-object ip
service-object esp
service-object icmp echo-reply
object-group service DM_INLINE_SERVICE_4
service-object object Sophos_Admin
service-object icmp echo
service-object icmp echo-reply
access-list outside_cryptomap extended permit object-group DM_INLINE_PROTOCOL_3 object MY-LAN object THIER-LAN
access-list outside_cryptomap_1 extended permit object-group DM_INLINE_PROTOCOL_2 object MY-LAN object THIER-LAN
access-list inside_cryptomap extended permit object-group DM_INLINE_PROTOCOL_1 object THIER-LAN object MY-LAN
access-list outside_access_out extended permit object-group DM_INLINE_SERVICE_3 object THIER_VPN host 82.222.222.38
access-list outside_access_out extended permit object-group DM_INLINE_SERVICE_1 any any
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 object THIER_VPN host 82.222.222.38
access-list inside_access_out extended permit object-group DM_INLINE_SERVICE_4 object MY-LAN object THIER-LAN
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-722.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network obj_any
nat (inside,outside) dynamic interface
access-group inside_access_out out interface inside
access-group outside_access_in in interface outside
access-group outside_access_out out interface outside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 81.111.111.156
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA
crypto map outside_map 1 set ikev2 ipsec-proposal AES
crypto map outside_map 2 match address outside_cryptomap_1
crypto map outside_map 2 set pfs
crypto map outside_map 2 set peer 81.111.111.156
crypto map outside_map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 2 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
crypto map outside_map interface outside
crypto ca trustpool policy
crypto ikev2 policy 20
encryption aes
integrity sha
group 2
prf sha
lifetime seconds 7800
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 7800
telnet timeout 5
ssh scopy enable
ssh stricthostkeycheck
ssh 192.168.1.0 255.255.255.0 inside
ssh timeout 30
ssh version 2
ssh key-exchange group dh-group1-sha1
console timeout 0
vpdn group Zen request dialout pppoe
vpdn group Zen localname MYISP@zen
vpdn group Zen ppp authentication chap
vpdn username MYISP@zen password ***** store-local
dhcpd auto_config outside
dhcpd address 192.168.1.5-192.168.1.36 inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
dynamic-filter updater-client enable
dynamic-filter use-database
dynamic-filter enable interface outside
dynamic-filter drop blacklist interface outside
webvpn
anyconnect-essentials
group-policy GroupPolicy_81.111.111.156 internal
group-policy GroupPolicy_81.111.111.156 attributes
vpn-tunnel-protocol ikev1
username admin password JsE9Hv42G/zRUcG4 encrypted privilege 15
username bob password lTKS32e90Yo5l2L/ encrypted
tunnel-group 81.111.111.156 type ipsec-l2l
tunnel-group 81.111.111.156 general-attributes
default-group-policy GroupPolicy_81.111.111.156
tunnel-group 81.111.111.156 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
inspect dns preset_dns_map dynamic-filter-snoop
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
hpm topN enable
Cryptochecksum:9430c8a44d330d2b55f981274599a67e
: end
ciscoasa#

Hi,
I started again and used various combinations of encryption etc but they all come back the same so I'm at a loss.
output of debug crypto ipsec 128
IPSEC: New embryonic SA created @ 0xcdbaeff8,
SCB: 0xCDC33C70,
Direction: inbound
SPI : 0x6699A5F8
Session ID: 0x00006000
VPIF num : 0x00000003
Tunnel type: l2l
Protocol : esp
Lifetime : 240 seconds
IPSEC: New embryonic SA created @ 0xcdc76048,
SCB: 0xCDB97B98,
Direction: outbound
SPI : 0xB4E5EBD5
Session ID: 0x00006000
VPIF num : 0x00000003
Tunnel type: l2l
Protocol : esp
Lifetime : 240 seconds
IPSEC: Completed host OBSA update, SPI 0xB4E5EBD5
IPSEC: Creating outbound VPN context, SPI 0xB4E5EBD5
Flags: 0x00000005
SA : 0xcdc76048
SPI : 0xB4E5EBD5
MTU : 1492 bytes
VCID : 0x00000000
Peer : 0x00000000
SCB : 0x3653C7F5
Channel: 0xc8c234e0
IPSEC: Completed outbound VPN context, SPI 0xB4E5EBD5
VPN handle: 0x0003820c
IPSEC: New outbound encrypt rule, SPI 0xB4E5EBD5
Src addr: 192.168.1.0
Src mask: 255.255.255.0
Dst addr: 192.168.30.0
Dst mask: 255.255.255.0
Src ports
Upper: 0
Lower: 0
Op : ignore
Dst ports
Upper: 0
Lower: 0
Op : ignore
Protocol: 0
Use protocol: false
SPI: 0x00000000
Use SPI: false
IPSEC: Completed outbound encrypt rule, SPI 0xB4E5EBD5
Rule ID: 0xca9505d8
IPSEC: New outbound permit rule, SPI 0xB4E5EBD5
Src addr: 88.222.222.38
Src mask: 255.255.255.255
Dst addr: 80.111.111.156
Dst mask: 255.255.255.255
Src ports
Upper: 0
Lower: 0
Op : ignore
Dst ports
Upper: 0
Lower: 0
Op : ignore
Protocol: 50
Use protocol: true
SPI: 0xB4E5EBD5
Use SPI: true
IPSEC: Completed outbound permit rule, SPI 0xB4E5EBD5
Rule ID: 0xcdc482c8
IPSEC: New embryonic SA created @ 0xcdbaeff8,
SCB: 0xCDC33C70,
Direction: inbound
SPI : 0x6699A5F8
Session ID: 0x00006000
VPIF num : 0x00000003
Tunnel type: l2l
Protocol : esp
Lifetime : 240 seconds
IPSEC: Completed host IBSA update, SPI 0x6699A5F8
IPSEC: Creating inbound VPN context, SPI 0x6699A5F8
Flags: 0x00000006
SA : 0xcdbaeff8
SPI : 0x6699A5F8
MTU : 0 bytes
VCID : 0x00000000
Peer : 0x0003820C
SCB : 0x363F2BE7
Channel: 0xc8c234e0
IPSEC: Completed inbound VPN context, SPI 0x6699A5F8
VPN handle: 0x00040e4c
IPSEC: Updating outbound VPN context 0x0003820C, SPI 0xB4E5EBD5
Flags: 0x00000005
SA : 0xcdc76048
SPI : 0xB4E5EBD5
MTU : 1492 bytes
VCID : 0x00000000
Peer : 0x00040E4C
SCB : 0x3653C7F5
Channel: 0xc8c234e0
IPSEC: Completed outbound VPN context, SPI 0xB4E5EBD5
VPN handle: 0x0003820c
IPSEC: Completed outbound inner rule, SPI 0xB4E5EBD5
Rule ID: 0xca9505d8
IPSEC: Completed outbound outer SPD rule, SPI 0xB4E5EBD5
Rule ID: 0xcdc482c8
IPSEC: New inbound tunnel flow rule, SPI 0x6699A5F8
Src addr: 192.168.30.0
Src mask: 255.255.255.0
Dst addr: 192.168.1.0
Dst mask: 255.255.255.0
Src ports
Upper: 0
Lower: 0
Op : ignore
Dst ports
Upper: 0
Lower: 0
Op : ignore
Protocol: 0
Use protocol: false
SPI: 0x00000000
Use SPI: false
IPSEC: Completed inbound tunnel flow rule, SPI 0x6699A5F8
Rule ID: 0xcdc35348
IPSEC: New inbound decrypt rule, SPI 0x6699A5F8
Src addr: 80.111.111.156
Src mask: 255.255.255.255
Dst addr: 88.222.222.38
Dst mask: 255.255.255.255
Src ports
Upper: 0
Lower: 0
Op : ignore
Dst ports
Upper: 0
Lower: 0
Op : ignore
Protocol: 50
Use protocol: true
SPI: 0x6699A5F8
Use SPI: true
IPSEC: Completed inbound decrypt rule, SPI 0x6699A5F8
Rule ID: 0xc96f7cc8
IPSEC: New inbound permit rule, SPI 0x6699A5F8
Src addr: 80.111.111.156
Src mask: 255.255.255.255
Dst addr: 88.222.222.38
Dst mask: 255.255.255.255
Src ports
Upper: 0
Lower: 0
Op : ignore
Dst ports
Upper: 0
Lower: 0
Op : ignore
Protocol: 50
Use protocol: true
SPI: 0x6699A5F8
Use SPI: true
IPSEC: Completed inbound permit rule, SPI 0x6699A5F8
Rule ID: 0xc96f6388

Unable to establish site to site vpn between asa 5505 an 5510

Hi ALL expert
We are now plan to form a site to site IPSec VPN tunnel between ASA 5505 (ASA Version 8.4) and ASA 5510 (ASA Version 8.0) but failure, would you please teach me how to establish it? Any reference guide?
Hugo

Here are the links to the cisco config-guides:
http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/site2sit.html
http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/vpn_site2site.html
In addition to VPN you need to look into NAT exemption:
http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/cfgnat.html#wp1043541
http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/nat_overview.html#wpxref25608
http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/nat_rules.html#wp1232160
And lots of examples:
http://www.cisco.com/en/US/products/ps6120/prod_configuration_examples_list.html
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

Cisco ASA 5505 Site to site VPN IPSEC tunnel to an Clavister Firewall

Hi,
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.
When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: show crypto isakmp sa
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.
They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505.
Here is some logs that ASDM give me about the tunnel issue, but like I said, the tunnel is up and only one remote network is reachable in that tunnel.....
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, Removing peer from correlator table failed, no match!
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, QM FSM error (P2 struct &0xc92462d0, mess id 0x1c6bf927)!
3
Nov 21 2012
07:11:09
713061
Group = 195.149.180.254, IP = 195.149.169.254, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 0.0.0.0/0.0.0.0/0/0 local proxy 0.0.0.0/0.0.0.0/0/0 on interface outside
5
Nov 21 2012
07:11:09
713119
Group = 195.149.180.254, IP = 195.149.169.254, PHASE 1 COMPLETED
Here is from the syntax: show crypto isakmp sa
Result of the command: "show crypto isakmp sa"
   Active SA: 1
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1   IKE Peer: 195.149.180.254
    Type    : L2L             Role    : responder
    Rekey   : no              State   : MM_ACTIVE
Result of the command: "show crypto ipsec sa"
interface: outside
    Crypto map tag: CustomerCryptoMap, seq num: 10, local addr: 213.180.90.29
      access-list arvika_garnisonen permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
      local ident (addr/mask/prot/port): (172.22.65.0/255.255.255.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.123.0/255.255.255.0/0/0)
      current_peer:195.149.180.254
      #pkts encaps: 2188, #pkts encrypt: 2188, #pkts digest: 2188
      #pkts decaps: 2082, #pkts decrypt: 2082, #pkts verify: 2082
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 2188, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: 213.180.67.29, remote crypto endpt.: 195.149.180.254
      path mtu 1500, ipsec overhead 74, media mtu 1500
      current outbound spi: E715B315
    inbound esp sas:
      spi: 0xFAC769EB (4207372779)
         transform: esp-aes-256 esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, PFS Group 5, }
         slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
         sa timing: remaining key lifetime (kB/sec): (38738/2061)
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0xFFFFFFFF 0xFFFFFFFF
    outbound esp sas:
      spi: 0xE715B315 (3876958997)
         transform: esp-aes-256 esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, PFS Group 5, }
         slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
         sa timing: remaining key lifetime (kB/sec): (38673/2061)
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
And here are my Accesslists and vpn site to site config:
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 84600
crypto isakmp nat-traversal 40
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map CustomerCryptoMap 10 match address VPN_Tunnel
crypto map CustomerCryptoMap 10 set pfs group5
crypto map CustomerCryptoMap 10 set peer 195.149.180.254
crypto map CustomerCryptoMap 10 set transform-set ESP-AES-256-SHA
crypto map CustomerCryptoMap interface outside
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0 -------> This is the only remote network I can reach behind the Cisco ASA and the other remote networks dont work..
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
nat (inside) 0 access-list nonat
All these remote networks are at the Main Site Clavister Firewall.
Best Regards
Michael

Hi,
I'd start by getting the configuration of the remote site related to Local/Remote network configurations and go through them. Even though no changes have been made.
If they are mirror images of eachother already I'd say its probably some problem related to Cisco/Clavister setup
Seems especially wierd to me that one of the error messages includes 0.0.0.0 lines.
I have run into some problems with L2L VPN configurations when our Cisco device just doesnt want to work with the remote end device. In some cases we have confirmed that our networks defined for the L2L VPN are exactly the same and yet when checking debugs on the ASA side we can see the remote end device using totally wrong network masks for the VPN negotiaton and therefore it failed. That problem we corrected with changing the network masks a bit.
Maybe you could try to change the Encryption Domain configurations a bit and test it then.
You could also maybe take some debugs on the Phase2 and see if you get anymore hints as to what could be the problem when only one network is working for the L2L VPN.
- Jouni

Cisco ASA 5505 IPSec tunnel won't establish until remote site attempts to connect

I have a site to site IPSec tunnel setup and operational but periodically the remote site goes down, because of a somewhat reliable internet connection. The only way to get the tunnel to re-establish is to go to the remote site and simply issue a ping from a workstation on the remote network. We were having this same issue with a Cisco PIX 506E but decided to upgrade the hardware and see if that resolve the issue. It ran for well over a year and our assumtions was that the issue was resolved. I was looking in the direction of the security-association lifetime but if we power cycle the unit, I would expect that it would kill the SA but even after power cycling, the VPN does not come up automatically.
Any assistance would be appreciated.
ASA Version 8.2(1)
hostname KRPS-FW
domain-name lottonline.org
enable password uniQue
passwd uniQue
names
interface Vlan1
nameif inside
security-level 100
ip address 10.20.30.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address xxx.xxx.xxx.xxx 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
description Inside Network on VLAN1
interface Ethernet0/2
shutdown
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
description Inside Network on VLAN1
ftp mode passive
dns server-group DefaultDNS
domain-name lottonline.org
access-list NONAT extended permit ip 10.20.30.0 255.255.255.0 10.20.20.0 255.255.255.0
access-list NONAT extended permit ip 10.20.30.0 255.255.255.0 192.168.0.0 255.255.255.0
access-list NONAT extended permit ip 10.20.30.0 255.255.255.0 192.168.15.0 255.255.255.0
access-list KWPS-BITP extended permit ip 10.20.30.0 255.255.255.0 10.20.20.0 255.255.255.0
access-list KWPS-BITP extended permit ip 10.20.30.0 255.255.255.0 192.168.0.0 255.255.255.0
access-list KWPS-BITP extended permit ip 10.20.30.0 255.255.255.0 192.168.15.0 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list NONAT
nat (inside) 1 0.0.0.0 0.0.0.0
access-group OUTSIDE_ACCESS_IN in interface outside
route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 10.20.30.0 255.255.255.0 inside
http 10.20.20.0 255.255.255.0 inside
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map DYNMAP 65535 set transform-set ESP-AES-256-SHA
crypto map VPNMAP 1 match address KWPS-BITP
crypto map VPNMAP 1 set peer xxx.xxx.xxx.001
crypto map VPNMAP 1 set transform-set ESP-AES-256-SHA
crypto map VPNMAP 65535 ipsec-isakmp dynamic DYNMAP
crypto map VPNMAP interface outside
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
ssh timeout 5
console timeout 0
management-access inside
tunnel-group xxx.xxx.xxx.001 type ipsec-l2l
tunnel-group xxx.xxx.xxx.001 ipsec-attributes
pre-shared-key somekey

Hi there,
I had same issue with PIX 506E and it was not even a circuit issue and I got ride of it and problem got fixed with PIX515E
I don't know, the device is too old to stay alive.
thanks

Two Cisco ASA 5505, IPSec Multiple Subnets, Problem with Phase2, DSL

Hi all.
we have following IPSec configuration:
ASA Site 1:
Cisco Adaptive Security Appliance Software Version 9.1(1)
crypto ipsec ikev1 transform-set TSAES esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TSMD5 esp-3des esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal PropAES256
access-list SITE_2 extended permit ip 172.27.0.0 255.255.0.0 172.27.97.0 255.255.255.0
access-list SITE_2 extended permit ip 172.28.60.0 255.255.254.0 172.27.97.0 255.255.255.0
access-list SITE_2 extended permit ip 172.22.0.0 255.255.0.0 172.27.97.0 255.255.255.0
access-list SITE_2 extended permit ip 172.27.0.0 255.255.0.0 172.27.99.0 255.255.255.0
access-list SITE_2 extended permit ip 172.22.0.0 255.255.0.0 172.27.99.0 255.255.255.0
crypto map CMVPN 5 match address SITE_2
crypto map CMVPN 5 set peer IP_SITE2
crypto map CMVPN 5 set ikev2 ipsec-proposal PropAES256
crypto map CMVPN interface OUTSIDE
route OUTSIDE 172.27.97.0 255.255.255.0 citic-internet-gw 255
route OUTSIDE 172.27.99.0 255.255.255.0 citic-internet-gw 255
tunnel-group IP_SITE2 type ipsec-l2l
tunnel-group IP_SITE2 general-attributes
default-group-policy VPN_S2S_WAN
tunnel-group IP_SITE2 ipsec-attributes
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
ASA Site 2:
Cisco Adaptive Security Appliance Software Version 9.1(4)
access-list SITE_1 extended permit ip 172.27.97.0 255.255.255.0 172.28.60.0 255.255.254.0
access-list SITE_1 extended permit ip 172.27.97.0 255.255.255.0 172.27.0.0 255.255.0.0
access-list SITE_1 extended permit ip 172.27.97.0 255.255.255.0 172.22.0.0 255.255.0.0
access-list SITE_1 extended permit ip 172.27.99.0 255.255.255.0 172.27.0.0 255.255.0.0
access-list SITE_1 extended permit ip 172.27.99.0 255.255.255.0 172.22.0.0 255.255.0.0
crypto map CMVPN 10 match address SITE_1
crypto map CMVPN 10 match address SITE_1
crypto map CMVPN 10 set peer IP_SITE1
crypto map CMVPN 10 set ikev2 ipsec-proposal IKEV2AES
crypto map CMVPN 10 set reverse-route
crypto map CMVPN interface OUTSIDE
tunnel-group IP_SITE1 type ipsec-l2l
tunnel-group IP_SITE1 general-attributes
default-group-policy VPN_S2S_WAN
tunnel-group IP_SITE1 ipsec-attributes
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
We are not able to reach from 172.22.20.x ips 172.27.99.x.
It seems so that the phase2 for this subnet is missing…...... as long as we try to reach from 172.27.99.x any ip in 172.22.20.x.
We are using similar configuration on many sites and it works correctly expect sites with DSL line.
We can exclude problem with NAT,ACL or routing. The connection is working fine as long as “we open all phase 2 manually” . After re-open (idle timeout) the tunnel the problem comes back.
Thanks in advance for your help.
Regards.
Jan
ASA Site 1# sh vpn-sessiondb detail l2l filter ipaddress ASA Site 2
Session Type: LAN-to-LAN Detailed
Connection   : IP ASA Site 2
Index        : 3058                   IP Addr      : IP ASA Site 2
Protocol     : IKEv2 IPsec
Encryption   : IKEv2: (1)AES256 IPsec: (3)AES256
Hashing      : IKEv2: (1)SHA512 IPsec: (3)SHA1
Bytes Tx     : 423634                 Bytes Rx     : 450526
Login Time   : 19:59:35 HKT Tue Apr 29 2014
Duration     : 1h:50m:45s
IKEv2 Tunnels: 1
IPsec Tunnels: 3
IKEv2:
Tunnel ID    : 3058.1
UDP Src Port : 500                    UDP Dst Port : 500
Rem Auth Mode: preSharedKeys
Loc Auth Mode: preSharedKeys
Encryption   : AES256                 Hashing      : SHA512
Rekey Int (T): 86400 Seconds          Rekey Left(T): 79756 Seconds
PRF          : SHA512                 D/H Group    : 5
Filter Name :
IPv6 Filter :
IPsec:
Tunnel ID    : 3058.2
Local Addr   : 172.22.0.0/255.255.0.0/0/0
Remote Addr : 172.27.97.0/255.255.255.0/0/0
Encryption   : AES256                 Hashing      : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds          Rekey Left(T): 22156 Seconds
Rekey Int (D): 4608000 K-Bytes        Rekey Left(D): 4607648 K-Bytes
Idle Time Out: 25 Minutes             Idle TO Left : 24 Minutes
Bytes Tx     : 312546                 Bytes Rx     : 361444
Pkts Tx      : 3745                   Pkts Rx      : 3785
IPsec:
Tunnel ID    : 3058.3
Local Addr   : 172.27.0.0/255.255.0.0/0/0
Remote Addr : 172.27.97.0/255.255.255.0/0/0
Encryption   : AES256                 Hashing      : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds          Rekey Left(T): 22165 Seconds
Rekey Int (D): 4608000 K-Bytes        Rekey Left(D): 4607952 K-Bytes
Idle Time Out: 25 Minutes             Idle TO Left : 24 Minutes
Bytes Tx     : 50014                  Bytes Rx     : 44621
Pkts Tx      : 496                    Pkts Rx      : 503
IPsec:
Tunnel ID    : 3058.4
Local Addr   : 172.27.0.0/255.255.0.0/0/0
Remote Addr : 172.27.99.0/255.255.255.0/0/0
Encryption   : AES256                 Hashing      : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds          Rekey Left(T): 22324 Seconds
Rekey Int (D): 4608000 K-Bytes        Rekey Left(D): 4607941 K-Bytes
Idle Time Out: 25 Minutes             Idle TO Left : 24 Minutes
Bytes Tx     : 61074                  Bytes Rx     : 44461
Pkts Tx      : 402                    Pkts Rx      : 437
NAC:
Reval Int (T): 0 Seconds              Reval Left(T): 0 Seconds
SQ Int (T)   : 0 Seconds              EoU Age(T)   : 6648 Seconds
Hold Left (T): 0 Seconds              Posture Token:
Redirect URL :
....  after ping from 172.27.99.x any ip in 172.22.20.x.
ASA Site 1# sh vpn-sessiondb detail l2l filter ipaddress ASA Site 2
Session Type: LAN-to-LAN Detailed
Connection   : IP ASA Site 2
Index        : 3058                   IP Addr      : IP ASA Site 2
Protocol     : IKEv2 IPsec
Encryption   : IKEv2: (1)AES256 IPsec: (4)AES256
Hashing      : IKEv2: (1)SHA512 IPsec: (4)SHA1
Bytes Tx     : 784455                 Bytes Rx     : 1808965
Login Time   : 19:59:35 HKT Tue Apr 29 2014
Duration     : 2h:10m:48s
IKEv2 Tunnels: 1
IPsec Tunnels: 4
IKEv2:
Tunnel ID    : 3058.1
UDP Src Port : 500                    UDP Dst Port : 500
Rem Auth Mode: preSharedKeys
Loc Auth Mode: preSharedKeys
Encryption   : AES256                 Hashing      : SHA512
Rekey Int (T): 86400 Seconds          Rekey Left(T): 78553 Seconds
PRF          : SHA512                 D/H Group    : 5
Filter Name :
IPv6 Filter :
IPsec:
Tunnel ID    : 3058.2
Local Addr   : 172.22.0.0/255.255.0.0/0/0
Remote Addr : 172.27.97.0/255.255.255.0/0/0
Encryption   : AES256                 Hashing      : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds          Rekey Left(T): 20953 Seconds
Rekey Int (D): 4608000 K-Bytes        Rekey Left(D): 4606335 K-Bytes
Idle Time Out: 25 Minutes             Idle TO Left : 24 Minutes
Bytes Tx     : 652492                 Bytes Rx     : 1705136
Pkts Tx      : 7419                   Pkts Rx      : 7611
IPsec:
Tunnel ID    : 3058.3
Local Addr   : 172.27.0.0/255.255.0.0/0/0
Remote Addr : 172.27.97.0/255.255.255.0/0/0
Encryption   : AES256                 Hashing      : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds          Rekey Left(T): 20962 Seconds
Rekey Int (D): 4608000 K-Bytes        Rekey Left(D): 4607942 K-Bytes
Idle Time Out: 25 Minutes             Idle TO Left : 24 Minutes
Bytes Tx     : 60128                  Bytes Rx     : 52359
Pkts Tx      : 587                    Pkts Rx      : 594
IPsec:
Tunnel ID    : 3058.4
Local Addr   : 172.27.0.0/255.255.0.0/0/0
Remote Addr : 172.27.99.0/255.255.255.0/0/0
Encryption   : AES256                 Hashing      : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds          Rekey Left(T): 21121 Seconds
Rekey Int (D): 4608000 K-Bytes        Rekey Left(D): 4607931 K-Bytes
Idle Time Out: 25 Minutes             Idle TO Left : 24 Minutes
Bytes Tx     : 70949                  Bytes Rx     : 50684
Pkts Tx      : 475                    Pkts Rx      : 514
IPsec:
Tunnel ID    : 3058.5
Local Addr   : 172.22.0.0/255.255.0.0/0/0
Remote Addr : 172.27.99.0/255.255.255.0/0/0
Encryption   : AES256                 Hashing      : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds          Rekey Left(T): 28767 Seconds
Rekey Int (D): 4608000 K-Bytes        Rekey Left(D): 4608000 K-Bytes
Idle Time Out: 25 Minutes             Idle TO Left : 24 Minutes
Bytes Tx     : 961                    Bytes Rx     : 871
Pkts Tx      : 17                     Pkts Rx      : 14
NAC:
Reval Int (T): 0 Seconds              Reval Left(T): 0 Seconds
SQ Int (T)   : 0 Seconds              EoU Age(T)   : 7852 Seconds
Hold Left (T): 0 Seconds              Posture Token:
Redirect URL :

Hi,
on 212 is see
tunnel-group 195.xxx.xxx.xxx type ipsec-l2l
tunnel-group 195.xxx.xxx.xxx ipsec-attributes
pre-shared-key
When you define the peer with static tunnel-group entry ASA is looking for peer configuration in static crypto map. If the peer is behind static NAT configure a proper static crypto map with matching acl and proposals.
If the peer is behind dynamic nat refer this example :http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/81883-ipsec-iosrtr-dyn-pix-nat.html
Regards,
Abaji.

Cisco ASA 5505 site to site Multiple subnet.

Hi. I need some help configuring my cisco asa 5505.
I've set up a VPN tunnel between two ASA 5505
Site 1:
Subnet 192.168.77.0
Site 2:
Have multiple vlans and now the tunnel goes to vlan400 - 192.168.1.0
What I need help with:
From site 1 i need to be able to reach another vlan on site 2. vlan480 - 192.168.20.0
And from site 1 I need to reach 192.168.77.0 subnet from vlan480 - 192.168.20.0
Vlan480 is used for phones. In vlan480 we have a PABX central.
Is this possible to do?
Any help would be greatfully appreciated!
Config site 2:
: Saved
ASA Version 7.2(2)
hostname ciscoasa
domain-name default.domain.invalid
enable password x encrypted
names
name 192.168.1.250 DomeneServer
name 192.168.1.10 NotesServer
name 192.168.1.90 OvServer
name 192.168.1.97 TerminalServer
name 192.168.1.98 w8-eyeshare
name 192.168.50.10 w8-print
name 192.168.1.94 w8-app
name 192.168.1.89 FonnaFlyMedia
interface Vlan1
nameif Vlan1
security-level 100
ip address 192.168.200.100 255.255.255.0
ospf cost 10
interface Vlan2
nameif outside
security-level 0
ip address 79.x.x.226 255.255.255.224
ospf cost 10
interface Vlan400
nameif vlan400
security-level 100
ip address 192.168.1.1 255.255.255.0
ospf cost 10
interface Vlan450
nameif Vlan450
security-level 100
ip address 192.168.210.1 255.255.255.0
ospf cost 10
interface Vlan460
nameif Vlan460-SuldalHotell
security-level 100
ip address 192.168.2.1 255.255.255.0
ospf cost 10
interface Vlan461
nameif Vlan461-SuldalHotellGjest
security-level 100
ip address 192.168.3.1 255.255.255.0
ospf cost 10
interface Vlan462
nameif Vlan462-Suldalsposten
security-level 100
ip address 192.168.4.1 255.255.255.0
ospf cost 10
interface Vlan470
nameif vlan470-Kyrkjekontoret
security-level 100
ip address 192.168.202.1 255.255.255.0
ospf cost 10
interface Vlan480
nameif vlan480-Telefoni
security-level 100
ip address 192.168.20.1 255.255.255.0
ospf cost 10
interface Vlan490
nameif Vlan490-QNapBackup
security-level 100
ip address 192.168.10.1 255.255.255.0
ospf cost 10
interface Vlan500
nameif Vlan500-HellandBadlands
security-level 100
ip address 192.168.30.1 255.255.255.0
ospf cost 10
interface Vlan510
nameif Vlan510-IsTak
security-level 100
ip address 192.168.40.1 255.255.255.0
ospf cost 10
interface Vlan600
nameif Vlan600-SafeQ
security-level 100
ip address 192.168.50.1 255.255.255.0
ospf cost 10
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
switchport access vlan 500
switchport trunk allowed vlan 400,450,460-462,470,480,500,510,600,610
switchport mode trunk
interface Ethernet0/3
switchport access vlan 490
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
passwd x encrypted
ftp mode passive
clock timezone WAT 1
dns server-group DefaultDNS
domain-name default.domain.invalid
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group service Lotus_Notes_Utgaaande tcp
description Frim Notes og ut til alle
port-object eq domain
port-object eq ftp
port-object eq www
port-object eq https
port-object eq lotusnotes
port-object eq pop3
port-object eq pptp
port-object eq smtp
object-group service Lotus_Notes_inn tcp
description From alle og inn til Notes
port-object eq www
port-object eq lotusnotes
port-object eq pop3
port-object eq smtp
object-group service Reisebyraa tcp-udp
port-object range 3702 3702
port-object range 5500 5500
port-object range 9876 9876
object-group service Remote_Desktop tcp-udp
description Tilgang til Remote Desktop
port-object range 3389 3389
object-group service Sand_Servicenter_50000 tcp-udp
description Program tilgang til Sand Servicenter AS
port-object range 50000 50000
object-group service VNC_Remote_Admin tcp
description FrÃ¥ oss til alle
port-object range 5900 5900
object-group service Printer_Accept tcp-udp
port-object range 9100 9100
port-object eq echo
object-group icmp-type Echo_Ping
icmp-object echo
icmp-object echo-reply
object-group service Print tcp
port-object range 9100 9100
object-group service FTP_NADA tcp
description Suldalsposten NADA tilgang
port-object eq ftp
port-object eq ftp-data
object-group service Telefonsentral tcp
description Hoftun
port-object eq ftp
port-object eq ftp-data
port-object eq www
port-object eq https
port-object eq telnet
object-group service Printer_inn_800 tcp
description Fra 800 nettet og inn til 400 port 7777
port-object range 7777 7777
object-group service Suldalsposten tcp
description Sending av mail vha Mac Mail programmet - Ã¥pner smtp
port-object eq pop3
port-object eq smtp
object-group service http2 tcp
port-object range 81 81
object-group service DMZ_FTP_PASSIVE tcp-udp
port-object range 55536 56559
object-group service DMZ_FTP tcp-udp
port-object range 20 21
object-group service DMZ_HTTPS tcp-udp
port-object range 443 443
object-group service DMZ_HTTP tcp-udp
port-object range 8080 8080
object-group service DNS_Query tcp
port-object range domain domain
object-group service DUETT_SQL_PORT tcp-udp
description For kobling mellom andre nett og duett server
port-object range 54659 54659
access-list outside_access_in extended permit ip any any
access-list outside_access_out extended permit ip any any
access-list vlan400_access_in extended deny ip any host 149.20.56.34
access-list vlan400_access_in extended deny ip any host 149.20.56.32
access-list vlan400_access_in extended permit ip any any
access-list Vlan450_access_in extended deny ip any host 149.20.56.34
access-list Vlan450_access_in extended deny ip any host 149.20.56.32
access-list Vlan450_access_in extended permit ip any any
access-list Vlan460_access_in extended deny ip any host 149.20.56.34
access-list Vlan460_access_in extended deny ip any host 149.20.56.32
access-list Vlan460_access_in extended permit ip any any
access-list vlan400_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan400_access_out extended permit tcp any host NotesServer object-group Lotus_Notes_Utgaaande
access-list vlan400_access_out extended permit tcp any host DomeneServer object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host TerminalServer object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host OvServer object-group http2
access-list vlan400_access_out extended permit tcp any host NotesServer object-group Lotus_Notes_inn
access-list vlan400_access_out extended permit tcp any host NotesServer object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host w8-eyeshare object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host w8-app object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host FonnaFlyMedia range 8400 8600
access-list vlan400_access_out extended permit udp any host FonnaFlyMedia range 9000 9001
access-list vlan400_access_out extended permit tcp 192.168.4.0 255.255.255.0 host DomeneServer
access-list vlan400_access_out extended permit tcp 192.168.4.0 255.255.255.0 host w8-app object-group DUETT_SQL_PORT
access-list Vlan500_access_in extended deny ip any host 149.20.56.34
access-list Vlan500_access_in extended deny ip any host 149.20.56.32
access-list Vlan500_access_in extended permit ip any any
access-list vlan470_access_in extended deny ip any host 149.20.56.34
access-list vlan470_access_in extended deny ip any host 149.20.56.32
access-list vlan470_access_in extended permit ip any any
access-list Vlan490_access_in extended deny ip any host 149.20.56.34
access-list Vlan490_access_in extended deny ip any host 149.20.56.32
access-list Vlan490_access_in extended permit ip any any
access-list Vlan450_access_out extended permit icmp any any object-group Echo_Ping
access-list Vlan1_access_out extended permit ip any any
access-list Vlan1_access_out extended permit tcp any host w8-print object-group Remote_Desktop
access-list Vlan1_access_out extended deny ip any any
access-list Vlan1_access_out extended permit icmp any any echo-reply
access-list Vlan460_access_out extended permit icmp any any object-group Echo_Ping
access-list Vlan490_access_out extended permit icmp any any object-group Echo_Ping
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_FTP
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_FTP_PASSIVE
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_HTTPS
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_HTTP
access-list Vlan500_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan470_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan470_access_out extended permit tcp any host 192.168.202.10 object-group Remote_Desktop
access-list Vlan510_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan480_access_out extended permit ip any any
access-list Vlan510_access_in extended permit ip any any
access-list Vlan600_access_in extended permit ip any any
access-list Vlan600_access_out extended permit icmp any any
access-list Vlan600_access_out extended permit tcp any host w8-print object-group Remote_Desktop
access-list Vlan600_access_out extended permit tcp 192.168.1.0 255.255.255.0 host w8-print eq www
access-list Vlan600_access_out extended permit tcp 192.168.202.0 255.255.255.0 host w8-print eq www
access-list Vlan600_access_out extended permit tcp 192.168.210.0 255.255.255.0 host w8-print eq www
access-list Vlan600_access_in_1 extended permit ip any any
access-list Vlan461_access_in extended permit ip any any
access-list Vlan461_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan400_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list outside_20_cryptomap_1 extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list outside_20_cryptomap extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list Vlan462-Suldalsposten_access_in extended permit ip any any
access-list Vlan462-Suldalsposten_access_out extended permit icmp any any echo-reply
access-list Vlan462-Suldalsposten_access_out_1 extended permit icmp any any echo-reply
access-list Vlan462-Suldalsposten_access_in_1 extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu Vlan1 1500
mtu outside 1500
mtu vlan400 1500
mtu Vlan450 1500
mtu Vlan460-SuldalHotell 1500
mtu Vlan461-SuldalHotellGjest 1500
mtu vlan470-Kyrkjekontoret 1500
mtu vlan480-Telefoni 1500
mtu Vlan490-QNapBackup 1500
mtu Vlan500-HellandBadlands 1500
mtu Vlan510-IsTak 1500
mtu Vlan600-SafeQ 1500
mtu Vlan462-Suldalsposten 1500
no failover
monitor-interface Vlan1
monitor-interface outside
monitor-interface vlan400
monitor-interface Vlan450
monitor-interface Vlan460-SuldalHotell
monitor-interface Vlan461-SuldalHotellGjest
monitor-interface vlan470-Kyrkjekontoret
monitor-interface vlan480-Telefoni
monitor-interface Vlan490-QNapBackup
monitor-interface Vlan500-HellandBadlands
monitor-interface Vlan510-IsTak
monitor-interface Vlan600-SafeQ
monitor-interface Vlan462-Suldalsposten
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-522.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (vlan400) 0 access-list vlan400_nat0_outbound
nat (vlan400) 1 0.0.0.0 0.0.0.0 dns
nat (Vlan450) 1 0.0.0.0 0.0.0.0 dns
nat (Vlan460-SuldalHotell) 1 0.0.0.0 0.0.0.0
nat (Vlan461-SuldalHotellGjest) 1 0.0.0.0 0.0.0.0
nat (vlan470-Kyrkjekontoret) 1 0.0.0.0 0.0.0.0
nat (Vlan490-QNapBackup) 1 0.0.0.0 0.0.0.0 dns
nat (Vlan500-HellandBadlands) 1 0.0.0.0 0.0.0.0
nat (Vlan510-IsTak) 1 0.0.0.0 0.0.0.0
nat (Vlan600-SafeQ) 1 0.0.0.0 0.0.0.0
nat (Vlan462-Suldalsposten) 1 0.0.0.0 0.0.0.0
static (vlan400,outside) 79.x.x.x DomeneServer netmask 255.255.255.255
static (vlan470-Kyrkjekontoret,outside) 79.x.x.x 192.168.202.10 netmask 255.255.255.255
static (vlan400,outside) 79.x.x.x NotesServer netmask 255.255.255.255 dns
static (vlan400,outside) 79.x.x.231 TerminalServer netmask 255.255.255.255
static (vlan400,outside) 79.x.x.234 OvServer netmask 255.255.255.255
static (vlan400,outside) 79.x.x.232 w8-eyeshare netmask 255.255.255.255
static (Vlan490-QNapBackup,outside) 79.x.x.233 192.168.10.10 netmask 255.255.255.255 dns
static (Vlan600-SafeQ,outside) 79.x.x.235 w8-print netmask 255.255.255.255
static (vlan400,outside) 79.x.x.236 w8-app netmask 255.255.255.255
static (Vlan450,vlan400) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (Vlan500-HellandBadlands,vlan400) 192.168.30.0 192.168.30.0 netmask 255.255.255.0
static (vlan400,Vlan500-HellandBadlands) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400,Vlan450) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400,outside) 79.x.x.252 FonnaFlyMedia netmask 255.255.255.255
static (Vlan462-Suldalsposten,vlan400) 192.168.4.0 192.168.4.0 netmask 255.255.255.0
static (vlan400,Vlan462-Suldalsposten) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400,Vlan600-SafeQ) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (Vlan600-SafeQ,vlan400) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ,Vlan450) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ,vlan470-Kyrkjekontoret) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan450,Vlan600-SafeQ) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (vlan470-Kyrkjekontoret,Vlan600-SafeQ) 192.168.202.0 192.168.202.0 netmask 255.255.255.0
access-group Vlan1_access_out out interface Vlan1
access-group outside_access_in in interface outside
access-group outside_access_out out interface outside
access-group vlan400_access_in in interface vlan400
access-group vlan400_access_out out interface vlan400
access-group Vlan450_access_in in interface Vlan450
access-group Vlan450_access_out out interface Vlan450
access-group Vlan460_access_in in interface Vlan460-SuldalHotell
access-group Vlan460_access_out out interface Vlan460-SuldalHotell
access-group Vlan461_access_in in interface Vlan461-SuldalHotellGjest
access-group Vlan461_access_out out interface Vlan461-SuldalHotellGjest
access-group vlan470_access_in in interface vlan470-Kyrkjekontoret
access-group vlan470_access_out out interface vlan470-Kyrkjekontoret
access-group vlan480_access_out out interface vlan480-Telefoni
access-group Vlan490_access_in in interface Vlan490-QNapBackup
access-group Vlan490_access_out out interface Vlan490-QNapBackup
access-group Vlan500_access_in in interface Vlan500-HellandBadlands
access-group Vlan500_access_out out interface Vlan500-HellandBadlands
access-group Vlan510_access_in in interface Vlan510-IsTak
access-group Vlan510_access_out out interface Vlan510-IsTak
access-group Vlan600_access_in_1 in interface Vlan600-SafeQ
access-group Vlan600_access_out out interface Vlan600-SafeQ
access-group Vlan462-Suldalsposten_access_in_1 in interface Vlan462-Suldalsposten
access-group Vlan462-Suldalsposten_access_out_1 out interface Vlan462-Suldalsposten
route outside 0.0.0.0 0.0.0.0 79.x.x.225 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
username x password x encrypted privilege 15
aaa authentication ssh console LOCAL
http server enable
http 192.168.210.0 255.255.255.0 Vlan450
http 192.168.200.0 255.255.255.0 Vlan1
http 192.168.1.0 255.255.255.0 vlan400
no snmp-server location
no snmp-server contact
snmp-server community public
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto map outside_map 20 match address outside_20_cryptomap_1
crypto map outside_map 20 set pfs
crypto map outside_map 20 set peer 62.92.159.137
crypto map outside_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp enable vlan400
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
tunnel-group 62.92.159.137 type ipsec-l2l
tunnel-group 62.92.159.137 ipsec-attributes
pre-shared-key *
telnet 192.168.200.0 255.255.255.0 Vlan1
telnet 192.168.1.0 255.255.255.0 vlan400
telnet timeout 5
ssh 171.68.225.216 255.255.255.255 outside
ssh timeout 5
console timeout 0
dhcpd update dns both
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan1
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface outside
dhcpd address 192.168.1.100-192.168.1.225 vlan400
dhcpd option 6 ip DomeneServer 81.167.36.11 interface vlan400
dhcpd option 3 ip 192.168.1.1 interface vlan400
dhcpd enable vlan400
dhcpd address 192.168.210.100-192.168.210.200 Vlan450
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan450
dhcpd option 3 ip 192.168.210.1 interface Vlan450
dhcpd enable Vlan450
dhcpd address 192.168.2.100-192.168.2.150 Vlan460-SuldalHotell
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan460-SuldalHotell
dhcpd option 3 ip 192.168.2.1 interface Vlan460-SuldalHotell
dhcpd enable Vlan460-SuldalHotell
dhcpd address 192.168.3.100-192.168.3.200 Vlan461-SuldalHotellGjest
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan461-SuldalHotellGjest
dhcpd option 3 ip 192.168.3.1 interface Vlan461-SuldalHotellGjest
dhcpd enable Vlan461-SuldalHotellGjest
dhcpd address 192.168.202.100-192.168.202.199 vlan470-Kyrkjekontoret
dhcpd option 3 ip 192.168.202.1 interface vlan470-Kyrkjekontoret
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan470-Kyrkjekontoret
dhcpd enable vlan470-Kyrkjekontoret
dhcpd option 3 ip 192.168.20.1 interface vlan480-Telefoni
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan480-Telefoni
dhcpd address 192.168.10.80-192.168.10.90 Vlan490-QNapBackup
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan490-QNapBackup
dhcpd option 3 ip 192.168.10.1 interface Vlan490-QNapBackup
dhcpd address 192.168.30.100-192.168.30.199 Vlan500-HellandBadlands
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan500-HellandBadlands
dhcpd option 3 ip 192.168.30.1 interface Vlan500-HellandBadlands
dhcpd enable Vlan500-HellandBadlands
dhcpd address 192.168.40.100-192.168.40.150 Vlan510-IsTak
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan510-IsTak
dhcpd option 3 ip 192.168.40.1 interface Vlan510-IsTak
dhcpd enable Vlan510-IsTak
dhcpd address 192.168.50.150-192.168.50.199 Vlan600-SafeQ
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan600-SafeQ
dhcpd enable Vlan600-SafeQ
dhcpd address 192.168.4.100-192.168.4.150 Vlan462-Suldalsposten
dhcpd option 6 ip DomeneServer 81.167.36.11 interface Vlan462-Suldalsposten
dhcpd option 3 ip 192.168.4.1 interface Vlan462-Suldalsposten
dhcpd enable Vlan462-Suldalsposten
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
prompt hostname context
Cryptochecksum:x
: end
Config site 1:
: Saved
ASA Version 7.2(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password x encrypted
passwd x encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.77.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group Telenor
ip address pppoe setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
switchport access vlan 15
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_access_in extended permit icmp any any echo-reply log disable
access-list outside_1_cryptomap extended permit ip 192.168.77.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.77.0 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
access-group outside_access_in in interface outside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http 192.168.77.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 79.160.252.226
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map interface outside
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.77.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn group Telenor request dialout pppoe
vpdn group Telenor localname x
vpdn group Telenor ppp authentication chap
vpdn username x password x store-local
dhcpd auto_config outside
dhcpd address 192.168.77.100-192.168.77.130 inside
dhcpd dns 192.168.77.1 interface inside
dhcpd option 6 ip 130.67.15.198 193.213.112.4 interface inside
dhcpd enable inside
dhcpd option 6 ip 130.67.15.198 193.213.112.4 interface outside
tunnel-group 79.160.252.226 type ipsec-l2l
tunnel-group 79.160.252.226 ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:x
: end

Hi,
The addition of a new network to the existing L2L VPN should be a pretty simple process.
Essentially you will have to add the network to the Crypto ACL present in the "crypto map" configurations. You will also have to configure the NAT0 configuration for it in the proper interfaces of the ASA. These configurations are all done on both ends of the L2L VPN connection.
Looking at your above configurations it would seem that you will need the following configurations
SITE 1
We add the new network to both the crypto ACL and the NAT0 ACL
access-list outside_1_cryptomap extended permit ip 192.168.77.0 255.255.255.0 192.168.20.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.77.0 255.255.255.0 192.168.20.0 255.255.255.0
SITE 2
We add the new network to the crypto ACL
We create a new NAT0 configuration for the Vlan480 interface as it has no previous NAT0 configuration
access-list outside_20_cryptomap_1 extended permit ip 192.168.20.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list VLAN480-NAT0 remark NAT0 for VPN
access-list VLAN480-NAT0 permit ip 192.168.20.0 255.255.255.0 192.168.77.0 255.255.255.0
nat (vlan480-Telefoni) 0 access-list VLAN480-NAT0
These configurations should pretty much do the trick.
Let me know if it worked
- Jouni

ASA 5505 - L2TP over IPsec - Remote Address shows outside interface address

Using an ASA 5505 for firewall and VPN. We've enabled L2TP over IPsec to allow Windows clients to connect without third party software.
The devices complete the connection and authenticate fine, but then are unable to hit any internal resources. Split tunneling seems to be working, as they can still hit outside resources. Packet tracer shows tcp flowing freely between VPN clients (192.168.102.0/24) and internal resources (192.168.100.0/24). Even the NAT translation looks good in packet tracer.
I pulled up the session details for one of the VPN clients in the ASDM and under the IPsecOverNatT details, it is showing the VPN client's remote address correctly, but displays the local address as the address assigned to the outside interface (which the client is using to connect.) This seems to be the problem, as viewing detailed connection logs shows the internal resources trying to send packets back to the outside interface rather than the VPN client's assigned internal addresses. Details:
Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: [OUTSIDE INTERFACE ADDRESS]
local ident (addr/mask/prot/port): ([OUTSIDE INTERFACE ADDRESS]/255.255.255.255/17/1701)
remote ident (addr/mask/prot/port): ([VPN CLIENT ADDRESS]/255.255.255.255/17/0)
current_peer: [VPN CLIENT ADDRESS], username: vpnuser
dynamic allocated peer ip: 192.168.102.1 [This is what I think it should be showing for local ident]
dynamic allocated peer ip(ipv6): 0.0.0.0
#pkts encaps: 16, #pkts encrypt: 16, #pkts digest: 16
#pkts decaps: 18, #pkts decrypt: 18, #pkts verify: 18
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 16, #pkts comp failed: 0, #pkts decomp failed: 0
#post-frag successes: 0, #post-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#TFC rcvd: 0, #TFC sent: 0
#Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
#pkts no sa (send): 0, #pkts invalid sa (rcv): 0
#pkts encaps failed (send): 0, #pkts decaps failed (rcv): 0
#pkts invalid prot (rcv): 0, #pkts verify failed: 0
#pkts invalid identity (rcv): 0, #pkts invalid len (rcv): 0
#pkts invalid pad (rcv): 0,
#pkts invalid ip version (rcv): 0,
#pkts replay rollover (send): 0, #pkts replay rollover (rcv): 0
#pkts replay failed (rcv): 0
#pkts min mtu frag failed (send): 0, #pkts bad frag offset (rcv): 0
#pkts internal err (send): 0, #pkts internal err (rcv): 0
local crypto endpt.: [OUTSIDE INTERFACE ADDRESS]/4500, remote crypto endpt.: [VPN CLIENT ADDRESS]/8248
path mtu 1500, ipsec overhead 82(52), media mtu 1500
PMTU time remaining (sec): 0, DF policy: copy-df
ICMP error validation: disabled, TFC packets: disabled
current outbound spi: 05BFAE20
current inbound spi : CF85B895
inbound esp sas:
spi: 0xCF85B895 (3481647253)
transform: esp-aes esp-sha-hmac no compression
in use settings ={RA, Transport, NAT-T-Encaps, IKEv1, }
slot: 0, conn_id: 77824, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
sa timing: remaining key lifetime (kB/sec): (4373998/3591)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x000FFFFD
outbound esp sas:
spi: 0x05BFAE20 (96448032)
transform: esp-aes esp-sha-hmac no compression
in use settings ={RA, Transport, NAT-T-Encaps, IKEv1, }
slot: 0, conn_id: 77824, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
sa timing: remaining key lifetime (kB/sec): (4373999/3591)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
Any ideas? The remote clients connect but when internal resources try to send traffic to the VPN clients, the packets are directed to the outside interface address instead of the local address assigned to the VPN client.

I have what I believe to be a similar issue. Site to site vpn is working well. That is site b can ping and send traffic to site A but Site A can not. Site B is a 3rd party vpn router. Site A is a Cisco 5505.
It appears that when the crypto map inserts the route into the routing table it shows the route via the outside IP of the outside interface and not the IP of Site B. in the crypto map I can see the proper ip address for the peer. I can't figure out why when it inserts the route that it uses the wrong ip address

ASA 5505 IPSEC VPN connected but can't access to LAN

ASA : 8.2.5
ASDM: 6.4.5
LAN: 10.1.0.0/22
VPN Pool: 172.16.10.0/24
Hi, we purcahsed a new ASA 5505 and try to setup IPSEC VPN via ASDM; i just simply run the Wizards, setup vpnpool, split tunnelling,etc.
I can connect to the ASA by using cisco VPN client and internet works fine on the local PC, but it cannot access to the LAN (can't ping. can't remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile i created worked fine.
Below is my configure, do I mis-configure anything?
ASA Version 8.2(5)
hostname asatest
domain-name XXX.com
enable password 8Fw1QFqthX2n4uD3 encrypted
passwd g9NiG6oUPjkYrHNt encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.1.1.253 255.255.252.0
interface Vlan2
nameif outside
security-level 0
ip address XXX.XXX.XXX.XXX 255.255.255.240
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns server-group DefaultDNS
domain-name vff.com
access-list vpntest_splitTunnelAcl standard permit 10.1.0.0 255.255.252.0
access-list inside_nat0_outbound extended permit ip 10.1.0.0 255.255.252.0 172.16.10.0 255.255.255.0
pager lines 24
logging enable
logging timestamp
logging trap warnings
logging asdm informational
logging device-id hostname
logging host inside 10.1.1.230
mtu inside 1500
mtu outside 1500
ip local pool vpnpool 172.16.10.1-172.16.10.254 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server AD protocol nt
aaa-server AD (inside) host 10.1.1.108
nt-auth-domain-controller 10.1.1.108
http server enable
http 10.1.0.0 255.255.252.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 10.1.0.0 255.255.252.0 inside
ssh timeout 20
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy vpntest internal
group-policy vpntest attributes
wins-server value 10.1.1.108
dns-server value 10.1.1.108
vpn-tunnel-protocol IPSec l2tp-ipsec
password-storage disable
ip-comp disable
re-xauth disable
pfs disable
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpntest_splitTunnelAcl
default-domain value XXX.com
split-tunnel-all-dns disable
backup-servers keep-client-config
address-pools value vpnpool
username admin password WeiepwREwT66BhE9 encrypted privilege 15
username user5 password yIWniWfceAUz1sUb encrypted privilege 5
username user3 password umNHhJnO7McrLxNQ encrypted privilege 3
tunnel-group vpntest type remote-access
tunnel-group vpntest general-attributes
address-pool vpnpool
authentication-server-group AD
authentication-server-group (inside) AD
default-group-policy vpntest
strip-realm
tunnel-group vpntest ipsec-attributes
pre-shared-key BEKey123456
peer-id-validate nocheck
privilege cmd level 3 mode exec command perfmon
privilege cmd level 3 mode exec command ping
privilege cmd level 3 mode exec command who
privilege cmd level 3 mode exec command logging
privilege cmd level 3 mode exec command failover
privilege cmd level 3 mode exec command packet-tracer
privilege show level 5 mode exec command import
privilege show level 5 mode exec command running-config
privilege show level 3 mode exec command reload
privilege show level 3 mode exec command mode
privilege show level 3 mode exec command firewall
privilege show level 3 mode exec command asp
privilege show level 3 mode exec command cpu
privilege show level 3 mode exec command interface
privilege show level 3 mode exec command clock
privilege show level 3 mode exec command dns-hosts
privilege show level 3 mode exec command access-list
privilege show level 3 mode exec command logging
privilege show level 3 mode exec command vlan
privilege show level 3 mode exec command ip
privilege show level 3 mode exec command ipv6
privilege show level 3 mode exec command failover
privilege show level 3 mode exec command asdm
privilege show level 3 mode exec command arp
privilege show level 3 mode exec command route
privilege show level 3 mode exec command ospf
privilege show level 3 mode exec command aaa-server
privilege show level 3 mode exec command aaa
privilege show level 3 mode exec command eigrp
privilege show level 3 mode exec command crypto
privilege show level 3 mode exec command vpn-sessiondb
privilege show level 3 mode exec command ssh
privilege show level 3 mode exec command dhcpd
privilege show level 3 mode exec command vpnclient
privilege show level 3 mode exec command vpn
privilege show level 3 mode exec command blocks
privilege show level 3 mode exec command wccp
privilege show level 3 mode exec command dynamic-filter
privilege show level 3 mode exec command webvpn
privilege show level 3 mode exec command module
privilege show level 3 mode exec command uauth
privilege show level 3 mode exec command compression
privilege show level 3 mode configure command interface
privilege show level 3 mode configure command clock
privilege show level 3 mode configure command access-list
privilege show level 3 mode configure command logging
privilege show level 3 mode configure command ip
privilege show level 3 mode configure command failover
privilege show level 5 mode configure command asdm
privilege show level 3 mode configure command arp
privilege show level 3 mode configure command route
privilege show level 3 mode configure command aaa-server
privilege show level 3 mode configure command aaa
privilege show level 3 mode configure command crypto
privilege show level 3 mode configure command ssh
privilege show level 3 mode configure command dhcpd
privilege show level 5 mode configure command privilege
privilege clear level 3 mode exec command dns-hosts
privilege clear level 3 mode exec command logging
privilege clear level 3 mode exec command arp
privilege clear level 3 mode exec command aaa-server
privilege clear level 3 mode exec command crypto
privilege clear level 3 mode exec command dynamic-filter
privilege cmd level 3 mode configure command failover
privilege clear level 3 mode configure command logging
privilege clear level 3 mode configure command arp
privilege clear level 3 mode configure command crypto
privilege clear level 3 mode configure command aaa-server
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4
: end

I change a Machine's gateway to this ASA and capture again, now we can see some reply.
All ohter PCs and switches gateway are point to another ASA, maybe that's the reason why i didn't work?
what's the recommanded way to make our LAN to have two 2 gateways(for load balance or backup router, etc)?
add two gateways to all PCs and swtichwes?
1: 18:15:48.307875 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   2: 18:15:49.777685 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   3: 18:15:51.377147 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   4: 18:15:57.445777 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   5: 18:15:58.856324 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   6: 18:16:00.395090 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   7: 18:16:06.483464 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   8: 18:16:08.082805 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
   9: 18:16:09.542406 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
10: 18:16:20.640424 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
11: 18:16:20.642193 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
12: 18:16:21.169607 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
13: 18:16:21.171210 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
14: 18:16:22.179556 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
15: 18:16:22.181142 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
16: 18:16:23.237673 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
17: 18:16:23.239291 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
18: 18:16:27.676402 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
19: 18:16:29.246935 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
20: 18:16:30.676921 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
21: 18:16:49.539660 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
22: 18:16:54.952602 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
23: 18:17:04.511463 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request

Asa 5505 Ipsec/ipad configuration

Hey Got some issues when setting up IPSEC/VPN on the asa 5505. I want to connect from the ipad with the built in IPSec client..
Get these errors when i run the debug crypto isakmp
Jan 28 22:03:26 [IKEv1]: Group = VPN_ipad, Username = Haq, IP = x.x.x.x, Tunnel Rejected: Conflicting protocols specified by tunnel-group and group-policy
Jan 28 22:03:26 [IKEv1]: Group = VPN_ipad, Username = Haq, IP = x.x.x.x, QM FSM error (P2 struct &0xd5d5f3d8, mess id 0x295bc3a)!
Jan 28 22:03:26 [IKEv1]: Group = VPN_ipad, Username = Haq, IP = x.x.x.x, Removing peer from correlator table failed, no match!
There is a bunch of vpn site-to-site and ipsec vpn profiles setup and those works fine..?
Here is the running config sh run crypto:
crypto ipsec transform-set DES esp-des esp-md5-hmac
crypto ipsec transform-set 3DES-TRANS esp-3des esp-sha-hmac
crypto ipsec transform-set 3DES-TRANS mode transport
crypto ipsec transform-set AES esp-aes esp-sha-hmac
crypto ipsec transform-set 3des esp-3des esp-md5-hmac
crypto ipsec transform-set IPAD-IPSEC esp-3des esp-sha-hmac
crypto ipsec transform-set IPAD-IPSEC mode transport
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map Plandent 10 set transform-set ESP-AES-128-SHA ESP-AES-256-SHA ESP-AES-128-MD5 ESP-AES-256-MD5 DES 3des 3DES-TRANS
crypto dynamic-map Plandent 10 set security-association lifetime seconds 84600
crypto dynamic-map Plandent 10 set security-association lifetime kilobytes 300000
crypto dynamic-map IPAD-MAP 5 set transform-set IPAD-IPSEC
crypto dynamic-map IPAD-MAP 5 set security-association lifetime seconds 28800
crypto dynamic-map IPAD-MAP 5 set security-association lifetime kilobytes 4608000
crypto map PD_VPN 10 match address ToGoteborg
crypto map PD_VPN 10 set peer PixGoteborg
crypto map PD_VPN 10 set transform-set DES
crypto map PD_VPN 10 set security-association lifetime seconds 84600
crypto map PD_VPN 10 set security-association lifetime kilobytes 4608000
crypto map PD_VPN 20 match address ToMalmo
crypto map PD_VPN 20 set peer PixMalmo
crypto map PD_VPN 20 set transform-set DES
crypto map PD_VPN 20 set security-association lifetime seconds 84600
crypto map PD_VPN 20 set security-association lifetime kilobytes 4608000
crypto map PD_VPN 30 match address ToPlanmeca
crypto map PD_VPN 30 set peer ASA_HKI ASA_HKI_BACKUP
crypto map PD_VPN 30 set transform-set AES
crypto map PD_VPN 30 set security-association lifetime seconds 86400
crypto map PD_VPN 30 set security-association lifetime kilobytes 4608000
crypto map PD_VPN 100 ipsec-isakmp dynamic Plandent
crypto map PD_VPN interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 10
authentication pre-share
encryption aes
hash sha
group 2
lifetime 28800
crypto isakmp policy 30
authentication pre-share
encryption des
hash md5
group 2
lifetime 86400
Anyone have any tips and tricks on what can be wrong here, will really be appreciated
Thanks
Shane

Well i created a new tunnel-group and a new group policy its still give me this error? that the tunnel is rejected:
Conflicting protocols specified by tunnel-group and group-policy
But as you can see the ipsec is allowed?
tunnel-group PLANDENT_IPAD type remote-access
tunnel-group PLANDENT_IPAD general-attributes
address-pool IPAD_VPN
default-group-policy PLANDENT_IPAD_Policy
tunnel-group PLANDENT_IPAD ipsec-attributes
pre-shared-key *
group-policy PLANDENT_IPAD_Policy internal
group-policy PLANDENT_IPAD_Policy attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN_ipad_splitTunnelAcl
/Shane

Vpn site to site isa 570 to asa 5505 multiple local lan

Hello, i have configured a site to site vpn with a asa 5505
In the tunnel will pass the network 172.x.x.x/16 and 192.168.x.x/24 from local isa to a single lan 192.168.x.x/24 on remote asa
I have create a group network address and i put the the default_lan and the other lan in it
In the tunnell configuration i have use this group address with local lan parameter
When the tunnel was up in the routing table i view the remote lan on interface ipsec0 but also i view the local lan on interface ipsec0
Is this configuration n ot supported?
Thank best regards

Hello, thank for answer.
The problem is that tha second lan is a routing static lan.
The ip address of ISA is 172.16.10.254/16 and the default_lan is 172.16.0.0/16
The second lan is 202.1.1.0/24 and it is a staic lan on another gateway.
When the site-to-site ipsec go up in routing table i see three route on interface ipsec0:
The remote lan, the default-lan (that is also on default interface. Behaviour?) and a subnet lan 172.16.10.0/24.
If i ping from a lan pc an ip of subnet 172.16.10.0/24, i see that the arp is equal at mac-address of ISA and i have a problem on the lan. It's normal?
Best regards

Multiple IPSEC tunnels on ASA 5505

Similar Messages

Maybe you are looking for