Multiple USB Device Driver Installations Failing

Windows 7 64 Bit / MSI P965 Platinum Mother Board
I have three USB driver installations failing. I believe this is related to ' USB', because installations of other software unrelated to USB devices install just fine. Might it be a Windows Installer Service, appears to be running fine?
Failing Device Driver Installations;
1) IOGEAR USB 3 PCIe card
Problem: The installer runs part way through the "Preparing to install' process and goes into limbo. I have tried three USB cards by different manufacturers and get the same problem. Tried several Renesas installers, all failed.
Microsoft Windows Installer says: 'Stopped working. Files that help describe the problem: AppCompat.txt, WERInternalMetadata.xml, WERDataCollection failure'.
2) APC Battery Backup 'PowerChute' Software
Problem: : The installer runs part way through the "Preparing to install' process and goes into limbo -or- I get an error message telling me to check the USB connection. APC cable is pulgged into a native port, not a hub. APC has no solution.
3) Logitech Harmony One Remote Software (Finally installed in 'Safe' Mode
Error: : The installer runs part way through the "Preparing to install' process and goes into limbo, but, when I went into 'Safe Mode' the software installed properly. Installation of the other two examples yield the Windows 'can't be installed in safe mode'
Help Appreciated - IM

To rule out a Windows problem, have you tested with a fresh parallel installation?

Similar Messages

Mtp device driver installation on nokia 5800 fails

when i connect my nokia 5800 in media transfer mode, windows try to find the drivers for the mtp device, but it always fails no matter what i have tried. i need to fix this.
Greece Nokia X6 RM-559 v40.0.002

Hi,
I have gotten my Nokia 5800 to work in all connection types.
Firstly, I had updated my phone to the latest firmware available to me via NSU (v31.0.101), and made a back up of my contacts and memory card.
1. Uninstalled Nokia PC suite, Cable driver, and PC connectivity (might not have got the exact names right).
2. Ran the Nokia PC suite cleaner.
3. Restarted the PC.
4. Formatted the memory card.
5. Did a hard reset on the phone (green button + red button + camera button - until country selection pops up during the power up of the phone)
6. Installed Nokia PC suite (latest version).
7. Connected the 5800 to the PC in the default connection, and let all the drivers install.
All the drivers, including the MTP USB device driver installed successfully. To be on the safe side, I changed the connection type from the phone toall the different connections to make sure it installed.
Also run the app update application first before restoring backups and re-installing applications.
Let me know if this helps.
Thanks.
Message Edited by H2_NokUser on 11-Nov-2009 05:38 PM

Qemu/kvm: multiple USB devices from the same vendor

Hi fellow gurus,
Trying to pass-through two USB devices. One works just fine, but two produces an error.
They are the same type from the same vendor and libvirt seems to have no way to differentiate between the two, as it only uses the <vendor id='0xnnnn'/> & <product id='0xnnn'/> strings and not serial number of the device.
There is a reference -unanswered- here: https://bugs.launchpad.net/qemu/+bug/1090602
The error message from virt-manager:
Error starting domain: operation failed: Multiple USB devices for 10c4:ea60, use <address> to specify one
Detailed output
Traceback (most recent call last):
File "/usr/share/virt-manager/virtManager/asyncjob.py", line 44, in cb_wrapper
callback(asyncjob, *args, **kwargs)
File "/usr/share/virt-manager/virtManager/asyncjob.py", line 65, in tmpcb
callback(*args, **kwargs)
File "/usr/share/virt-manager/virtManager/domain.py", line 1063, in startup
self._backend.create()
File "/usr/lib64/python2.6/site-packages/libvirt.py", line 678, in create
if ret == -1: raise libvirtError ('virDomainCreate() failed', dom=self)
libvirtError: operation failed: Multiple USB devices for 10c4:ea60, use <address> to specify one
The devices themselves:
Bus 001 Device 009: ID 10c4:ea60 Cygnal Integrated Products, Inc. CP210x UART Bridge / myAVR mySmartUSB light
Bus 001 Device 008: ID 10c4:ea60 Cygnal Integrated Products, Inc. CP210x UART Bridge / myAVR mySmartUSB light
Is there any workaround or fix for this?
Cheers,
Mike.
Last edited by DrMikeDuke (2013-07-22 14:01:18)

As I understand it, host:bus.addr is an alternative to host:vendor_id:product_id. So if I wanted to pass both of these thumb drives:
$ lsusb
Bus 001 Device 002: ID 1e3d:2093 Chipsbank Microelectronics Co., Ltd CBM209x Flash Drive (OEM)
Bus 001 Device 003: ID 1e3d:2093 Chipsbank Microelectronics Co., Ltd CBM209x Flash Drive (OEM)
I would use host:001.002 and host:001.003 . Note I said would use, because I've never tried it.
And usb_add is a qemu monitor command. See sections 3.4 and 3.5 of the doc you linked for info on the monitor.
All this being said, I don't use libvirt stuff so I don't know if it has the capability to specify USB devices by bus.addr or whether or not it enables the monitor.

E72 / Win7 64-bit Ovi Suite - MTP USB device drive...

Just installed Ovi Suite (most recent version) on Windows 7 64-bit for my E72.
Windows installs all drivers, however 'MTP USB device ' driver fails to install.
What does this driver do ? And can this be solved ?

I am running OVI 2.2.0.245 on 64 bit W7 and Office 2007 and using a 5800ExpreMusic..
I have experienced all the problems mentioned above. After 2 days of try and error end nearly getting crazy I found a solution at least for my situation. However I can imagine many more people are maybe in the same situation.
At first I had been using the USB ports in front of the machine's cabinet. None of them worked for a longer period than 3 minutes and I always lost the connection to the mapserver. Until I found out that each two ports in front of the cabinet share the capacity of a single USB connection at the back of the system. So I moved the USB from one of the front ports the a back port. Now that the full Capacity of a USB port can be used I no longer suffer any problems with OVI.
It works great.
However it is a shame Nokia users must find out what Nokia could have told its users.

Apple iPod USB Device driver issue on Win XP - syncing shuffle 2nd gen.

Hello fellow iPod shuffle users. Any of you run into this problem using the following configurations? Any advise/recommendations/workarounds much appreciated as I've burned 3 days on this issue and I'm still stonewalled.
I personally think it's a device driver issue/bug and am searching for a way to update my Apple iPod USB device driver for Win XP. Two brand new ipod shuffles (received for Christmas 2008) are both behaving this way, so the problem most likely points to a global software issue more-so than to shuffle hardware issue.
PROBLEM STATEMENT: Driver data i/o streaming issue does not allow shuffle to sync data with iTunes after initial sync (i.e. reading the content of the shuffle is good, but writing modified content fails). Posted error message "The ipod ... cannot be synced. Required disk cannot be found". After cracking the hood on my device driver, the problem seems to point to the Apple iPod USB device driver for Win XP. Driver will recognize the shuffle and read to it, but subsequent write attempts will result in device driver balks that "this device cannot start (code 10)".
ATTEMPTED WORKAROUNDS:
*Read All "How to Get Started Manuals" to make sure I was using the right technique for syncing my two shuffles from within iTunes... tried and failed
*Ensure only one shuffle was plugged in at a time (saw notice that two shuffles plugged in at the same time is not yet a supported config)... tried and failed
*The 5 R's as recommended by Apple Support... tried and failed.
*I've tried all 3 built in USB ports on my Lenovo T60. no love... tried and failed.
*Per discussion board: From Window's Device Manager-> Scaned for new hardware while shuffle was syncing...tried and failed.
* Per Discussion board: From Window's Disk Management -> Ensured shuffle came up as a FAT32 filesystem... connection tore down as quickly as windows recognized it.... tried and failed.
*From Windows Software config utility: Ran repair to re-install itunes 8... same results.
*From Windows software management utility: Uninstalled and reinstalled itunes 8... same results.
Hardware: IBM Thinkpad/Lenovo T60. Using build in k/b & no external mouse. Has 3 USB built in ports.
Software: Windows XP Pro SP2/iTunes 8.0.2/shuffle (2nd gen) driver 1.0.4 (same behavior using the original driver 1.0.3).
Apple iPod USB Device properties:
Driver Provider - Microsoft
Driver Date - 7/1/2001
Driver Version - 5.1.2535.0
Digital Signer - Microsoft Windows Publisher

Hi. Ive got pretty much the same problem.... Got a new shuffle for christmas..having real problems syncing with itunes. Funnily enough I managed to get 25 tracks on it but then it just stopped. error message says " The ipod shuffle cannot be synced. The required disk cannot be found." Ive done restore, and downloaded a reset utility thingy to try but still no joy.

Is it possible, to add multiple USB devices to TC

Is it possible, to add multiple USB devices using a hub to Time Capsule (as stated for Airport Extreme)?
Thanks in advance.
Stefan

The Time Capsule is an AirPort Extreme with a built-in hard drive, so you can add multiple USB devices if you use a powered USB hub.

Can I set up multiple usb hard drives- one for time machine and a second for media? Can one also print wirelessly with an old HP C6280 printer?

Can I set up multiple usb hard drives- one for time machine and a second for media?
Can one also print wirelessly with an old HP C6280 printer?

Can I set up multiple usb hard drives- one for time machine and a second for media?
Yes.
Can one also print wirelessly with an old HP C6280 printer?
Possibly by using an Airport Express, but depends on what type of port connection the printer requires.

When I plug in my iPhone to a USB port on the back of my computer I get the error "MTP USB Device driver was not successfully installed" and of course there is no device that shows up either. It would be great to download my photos! I'm using Windows

When I plug in my iPhone to a USB port on the back of my computer I get the error "MTP USB Device driver was not successfully installed" and of course there is no device that shows up either. It would be great to download my photos! I'm using Windows

Go through this support doc:
OS: Device not recognised in iTunes
Windows: http://support.apple.com/kb/TS1538

SoundBlaster X-Fi Driver Installation Fails After Moving Soundcard to New Slot

NSoundBlaster X-Fi Driver Installation Fails After Moving Soundcard to New Slot4 I recently moved my X-Fi Elite Pro soundcard to a different PCI slot to accommodate my new large PCIE graphics card.
Prior to moving the card, my?original SoundBlaster install went fine without any trouble. When I booted up after relocating the card,?it was not detected at all. So I uninstalled my SoundBlaster driver software and?rebooted the computer?thinking that was necessary to clear any hardware configuration settings from the old install. This made no difference. I then discovered my card was not seated properly and corrected it.
Next I installed the SoundBlaster driver software. The installation proceeded and finished with a request to restart the computer. Once I did, the computer detects my card and starts the hardware installation wizard asking if I want Windows to search online for driver software. It does not recognize the just installed SoundBlaster driver installation. I have a dual boot setup and this happens in both WinXP Pro and Vista 32 Home Premium.
What's wrong here?

Forget it folks...couldn't wait for any suggestions so I just cleaned off my hard dri've and reinstalled everything. Works fine.

After iOS 7 update to my 4s, Windows device driver install fails. Why?

on iOS 6, my 4s worked fine on Windows computers. just installed iOS 7 and now Windows Apple device driver install failed. any ideas or fixes?

Reboot the computer.
Restart the iPhone.
Install the latest version of iTunes, 11.1 is required for syncing with iOS7.
Remove all Apple related components and reinstall iTunes.

Device Driver Installation on Virtual PC XP mode

Hi,
I am having Windows 7 Professional setup. I have installed Windows Virtual PC XP Mode on it. I need to access USB for connecting my Windows Embedded device with Visual Studio Platform Builder which has installed in XP mode. Using USB over network
tool i have tried to make the USB device to be accessible from XP mode and tried to install APX USB driver in Virtual PC.
I got this notification from the installation setup "Could not start the Hardware" . Also checked this USB device installation with other XP pc. There it worked fine.
Is there any option to make the USB device accessible from virtual PC ?
Best Regards,
Dinesh

Hi,
The USB device might need to be redirected:
We may take a look at the following article about USB device usage in Virtual PC:
Use a USB device in a virtual machine
To redirect a USB device to a virtual machine
Attach the device to the physical computer and turn on the device.
From the virtual machine window, click USB and then click
Attachdevice name. Windows looks for and tries to install the device driver in the guest operating system. You also can install the driver from the Internet or from a CD.
After the driver is installed, you can use the USB device from within the virtual machine the same way as you would on a physical computer. However, USB devices that are connected using these steps are not shared, so they must be released from one operating
system to be available for use on the other operating system.
To make the USB device available on the host operating system, release it from the virtual machine. From the virtual machine window, click
USB and then click Releasedevice name.
Best regards
Michael Shao
TechNet Community Support

Multiple USB devices

So I use Logic Pro on my Macbook A LOT! I use my firewire port for a mixer (works perfect) but I've got numerous devices that use USB (e.g. trigger finger, conntectiv box, external hard drive etc.) I want to have them all hooked up to my mac at the same time. I've got one adapter for a USB that adds 4 ports to it but it isn't powered so runs sooooo slowly its painful!
Should I look into buying a powered 4-way USB adapter? If so, can you suggest one? And would it affect the performance of any of my devices/mac?
Cheers

AreMad wrote:
So I use Logic Pro on my Macbook A LOT! I use my firewire port for a mixer (works perfect) but I've got numerous devices that use USB (e.g. trigger finger, conntectiv box, external hard drive etc.) I want to have them all hooked up to my mac at the same time. I've got one adapter for a USB that adds 4 ports to it but it isn't powered so runs sooooo slowly its painful!
Powered or passive doesn't affect the speeds through a USB hub.
Only one USB device can actually communicate through USB at a given instant. The host device operating system handles all of this and hooking up multiple devices that are bandwidth hungry means that they will inevitably be slowed down.

Unattended driver installation fails with code 800b0109

hi there
i´m trying to install server 2012r2 unattended.
at the moment its failing while installing some driver.
the driver are signed and - as far i can see it - the signature chain is complete with no errors.
however - when i´m trying to install the driver (i´ve tried pnputil and devcon, or even manually) i get a message that the driver isnt trusted.
when i accept this message everythink is working - but its no unattended installation.
i´ve checked the setupapi.dev.log and found this:
! sig: Verifying file against specific (valid) catalog failed! (0x800b0109)
! sig: Error 0x800b0109: A certificate chain processed, but terminated in a root certificate which is not trusted by the trust provider.
i am willing and able to install the root certificate - but which one??
how can i find out which certificate is affected?
*edit*
it seems that disabling the testsigning via bcdedit is not longer working under 2012r2
or do i need more than one step?
thx
netlord

Hi,
If an unsigned or invalid boot-critical device driver is installed on an x64-based computer, the computer will not boot. The unsigned or invalid boot-critical device driver
will cause a Stop error.
If you trust this driver and trying to install this unsigned driver, use /ForceUnsigned to override the requirement that drivers installed on X64-based computers must have
a digital signature. For example,
Dism /Image:C:\test\offline /Add-Driver /Driver:C:\drivers\mydriver.INF /ForceUnsigned
The related KB:
Understanding Device Drivers and Deployment
http://technet.microsoft.com/en-us/library/dd744517(v=ws.10).aspx
Signing Device Driver Packages
http://technet.microsoft.com/en-us/library/cc771511(v=ws.10).aspx
Add and Remove Drivers Offline
http://technet.microsoft.com/en-us/library/dd744355(v=ws.10).aspx
More information:
Cross-Certificates for Kernel Mode Code Signing
http://msdn.microsoft.com/en-us/library/windows/hardware/dn170454(v=vs.85).aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Re: Satellite P100-160 - Display driver installation failed

Satellite P100-160, PSPAAE, vista 32 bit,
Today Aero wasn't working and not available in graphics properties. Installed latest display driver from Toshiba UK site, Intel 15.0.1.1114. This version was actually older than my current driver but I thought that maybe as it was the only one availabel that it must be correct.
The driver install failed with an error (no details just 'an error has occurred'). Now I have no aero and my display resolution cant be set above 1280x800 - should be 1440x900
To say I am pisseed would be an understatement. Can anyone help? thanks

Hey,
If Aero is not available I dont think its display driver problem
Anyway, have you removed the old display driver before you installed the new one? Go to device manager > right click on graphic card > uninstall. After reboot the display driver should be uninstalled and you can start with display driver installation.
If you install drivers make sure you are logged in as Administrator and antivirus/firewall is disabled. Restart once again and you should be able to choose the native screen resolution now.
Check this!!!

Apple IPod USB Device Driver Not Installed? WIndows not reconizing IPod!

Hoping someone can help me with my new Ipod Nano. I installed the IPod Updater and Itunes programs from the provided CD and formatted the Ipod. That all works fine -- the Ipod actually works, etc.
But during the actuall instation process, the Hardware Update Window came up for the 'Apple IPod USB Device' (I use Windows XP) I've tried to have it install automaticaly and manualy, without any luck. As a result, when the IPod is connected to the computer, I get a '!' on the device in Windows Explorer and neither ITunes or the Ipod Updater -- or Windows -- will reconize it!
If I connect my Ipod to the computer, the 'hardware' icon comes up in my system tray and the Ipod screen changes to the 'Do not disconnect' message. I can click on the hardware icon to 'remove' it. But I can't DO anything with the Ipod if nothing will reconize it!
I've tried updating the ITunes and Updater to the latest versions, plugged the USB cable into different spots on my computer, uninstalled and reinstalled everything, this time selecting the 'do not connect the Ipod to the computer at this time' option.....nothing. Windows just will NOT reconize the IPod and everytime I install the software I get that Hardware Update Window screen up!
Is there a driver for this I'm missing somewhere? What's going on? I can't do anything with my IPod and can't even find a phone number to call Apple for help!

1-800-275-2273.
This might be an issue with your operating system. You might also want to try using it on another computer before calling them as they'll probably ask you to do so. This will isolate the problem to your computer and they might tell you to try calling Windows or getting the latest drivers for your computer.

Multiple USB Device Driver Installations Failing

Similar Messages

Maybe you are looking for