Muvo TX FM weird connection prob

Hy everybody! Im from Germany, but bought my MUVO 256 TX FM over the internet about a year ago, and it worked quite well all this time, untill last week!
The weird thing is that the player works just fine, I can listen to the music already stored inside, but when I connect it to any computer (I tried about 5 different now), there is no response at all!! It is not even recognized as 'new hardware' or 'other hardware' in the device manager!!
However, the player shows the tipical "connected" screen when I plug it in!
Someone Help me!! XD
And Thanks for at least trying

It should be in the manual... but basically you connect the player to the PC and it should appear as a dri've letter in Windows Explorer. You then copy supported audio files e.g. WMA, MP3, to the player as the dri've letter. Once copied you disconnect the player and the songs should be there and available to play.

Similar Messages

  • "Disk Full" error message on Muvo TX FM 512, connected to Wi

    The Muvo TX FM 52 connects fine to my Windows 2000 laptop, and my windows XP desktop, but when transferring files (drag and drop) I get an error message stating that the disk is full. Windows explorer and Checkdisk both report over 00 MB available. Not sure what to make of the problem, and am open to suggestions.

    - No, it doesn't appear. But, I don't physically have the player....it's with my daughter who li'ves in another town. According to her, it did not show up in My Computer. In fact, when she put the player into her USB port on the laptop, it didn't say "found hardware" or any message, which it usually does.
    I know her laptop has Windows XP sp2, she has Windows Media Player 0, but not Creative Media Source, since we did not install the CD that came with the player onto her laptop. I didn't think it needed any drivers since it's XP. Isn't that correct? Or is that the problem?
    2 - My other problem lies with the new MuVo TX FMG player I received yesterday. My PC has Windows XP Pro, no service packs. How come when I transferred music to it, nothing happened,shows "no music" when I turned it on. I saw all the files transferring. Yet when I go to explore the dri've on the PC, the music is all folders, like 50 of them? The music is there but doesn't show up on the player.
    I used WMP to transfer the music, using drag and drop. I wound up deleting everything and transferred the same music using Creative Media Source and that works fine. I am very confused with both players. Thank goodness all I do is build and repair PCs!!! MP3 stuff is over my head I think!
    Sorry, this post really should have been in two questions.

  • Airport connection probs with Mac Pro and 10.4.8  too.

    This prob is not just related to iMacs or MacBooks as published in the knowledge base doc. I have exactly the same prob with my 2.66 GHz Mac Pro. I have to reconnect this beast to my wlan router manually every time.
    PLZ Apple fix this asap!

    I had a similar problem which I've fixed!
    I have four machines here which can connect to my Netgear DG834N via Aiport. (I say can because they normally connect via ethernet.) My MacBook Pro always used to be fine when connected wirelessly but recently, not aware of any changes I've made, it connects for about 10 seconds then disconnects. All other machines are fine and hold the connection.
    This is what I tried before finding my solution:
    1) Deleted all references to the network in the keychain and remade them.
    2) Created another user to try
    3) Changed channels on the router even though I can't see any neighbour's networks.
    4) Made sure computer and router were up to date with firmware/software.
    I'm assuming that it has to be a computer problem as the PowerMac, iMac and iPod Touch have no issues at all. However, the cure was in the router.
    I run with SSID broadcast turned off, WPA2 encryption and MAC address filtering. Allowing broadcast of the SSID cures my problem. Turn it off and the computer connects then drops it ten seconds later. Turn broadcast on and it maintains the connection. I've tried it all afternoon, leaving it connected for about 30 minutes at a time before turning SSID broadcast off again. Works every time! Broadcast SSID - fine, no broadcast - drops after ten seconds.
    Now, if only I knew why! And why only the laptop?

  • E1200 weird connection problem

    Recently I got a brand new E1200 from the Cisco store to replace Apple Extreme Base station for my home wireless network. The router deployed just fine except one weird problem. While all devices (desktops, laptops, cell phones, iPad) can access the router, one desktop (Dell Optiplex DX280)  cannot see the router at all. The router network, even with default SSID, does not even show in the wireless network list, no matter how many times the list is refreshed. The wireless adapter (Dell TrueMobile 1800 USB2.0) is fine, since it picks up the router SSID when connected to another desktop. The stubborn desktop works just fine with previous Apple router and can see many networks around, like neighbors' networks.  Thinking that some other previously installed software interferes with seeing the router SSID, I completely wiped and reformatted HD and reinstalled fresh copy of WinXP - still the same result, the dektop works just fine with the Apple router, but still cannot see E1200 SSID. The router was reset to factory defaults and all access restrictions were removed. While all the devices see the default SSID and can conncet to the router with no problems, the stubborn desktop keepcompletely ignoring it. Any ideas what may be the problem?

    It is SP3, and there was no error message. SSID just was not showing up in list of available networks on Optiplex desktop. As I found later, just by chance in contrast to getiing answer straight from Dell, it was a driver issue. Optiplex desktop was equipped with older driver, 1.5.0.1 or so, a while ago because this is what was recommended (and continues to be recommended!) at Dell's site for the supplied service tag. It was working just fine with Apple router. On the other hand, the Compaq desktop, which was picking up routher's SSID normally with the same USB adaptor, somehow had loaded a newer version, 3.3 something, from the internet. When the older  driver was installed from the Dell website, Compaq lost all wireless capabilities. So when I just upgraded driver from within WinXP Device Manager, the newer version was installed and the missing SSID has immediately shown up in Optiplex' wireless network list. I wish that Dell suooprt and site was better organized, but it is as bad as jungle and Tech Support asks a lot of irrelevant questions wasting their and my time and getting nowhere.

  • Weirdness connecting a mac to a windows fileserver

    Hi All,
    I've got some weirdness with my mac connecting to a windows file share. It seems to only pull up documents modified three months ago or later. For instance, if I create a new excel sheet on my windows computer and save it on the file server, other macs and windows machines can see the file. If i connect to the file server on my mac, I don't see the file. It's almost like my mac is only pulling up a cached version of the files from a while ago. Has anyone heard or this or how I should go about troubleshooting this?
    I've tried reconnecting to the server and it had no impact. The only other article I was able to find mentioned that the mac caches files periodically via mobile sync http://community.spiceworks.com/topic/282342-offline-files-on-a-mac however, I am not able to verify this because of the error "securityagent may only be invoked by apple software" http://forums.macrumors.com/showthread.php?t=1723409
    computer info: Mac OS X 10.9.5 BldID: 13F34
    Joined to the windows domain
    Let me know what additional information you need

    The following should be helpful:
    http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh1163.html
    http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh1161.html

  • MuVo TX FM Adding song prob

    I was wondering if anyone would be able to help me. I reci'ved an MuVo TX FM for Christmas and i can't figure out how to add songs to it. I have look all over this site and can not find anything on how to add them. My computer is a Dell Windows Xp, also. Please help me out!
    --Michael

    It should be in the manual... but basically you connect the player to the PC and it should appear as a dri've letter in Windows Explorer. You then copy supported audio files e.g. WMA, MP3, to the player as the dri've letter. Once copied you disconnect the player and the songs should be there and available to play.

  • Muvo^2 FM (5gb) scandisk prob

    I saw an earlier post that had the same problem as me, but there was no follow up answer.
    Anyway, my problem is that when I start my Muvo up, it says that smartscan failed, and that I should press the menu button to go into recovery mode.
    I then select PC scandisk, and it tells me to attach the USB cord.
    Afterwards, the computer detects the Muvo, but nothing more happens. The screen on the Muvo is simply the icon that indicates that it is connected, but scandisk is not run at all.
    I'm sure I am just skipping something really simple.
    Thanks in advance to anyone who can help me.

    eneleon,
    You need to run Scandisk from Windows manually. Open Windows Explorer and right click at the removable disk dri've letter of the player. Select Properties -> Tools tab -> Error checking column. Select the option 'Automatically fix file system errors' and start the process. Be sure to disconnect the player properly using the Safely remove hardware icon at the taskbar.
    Jason

  • Weird Registration Prob

    Hey everyone... I'm having a weird registration problem. So I just got a Creative Zen Vision 60GB and I installed it comepletely and after about a week I started getting a pop-up screen on my desktop that says "Gentle Reminder: Register your Creative products now to enjoy a host of benefits." So of course I registered it but that pop up continues to be on my desktop ALL the time and I have tried everything I can think of to get rid of it. If I X out if it, it takes me to another pop-up "If you are registering portable products, please ensure that they are connected and switched on before clicking on the OK button" If I click OK it goes on with the registration process. I have uninstalled all Creative components on my computer but the pop-up remained every time I turned on the computer. I re-installed everything. Same problem. Can anyone help me? This is driving me nuts!

    Have you tried selecting the option where you don't want to register, and select for it to not remind you Or does it still pop up then If you tried that and it didn't work, you can manually stop it from starting up in Start-> Run-> then type MSCONFIG. Under StartUp you'll see a list of programs that load automatically when Windows starts, if you untick it there it won't start up again.
    Cat

  • LiveCache Connection Probs

    Hi Basis Gurus
    I need a Help from u, While i am trying to connect a APO LiveCache
    server I am getting this error for this how can i solve this probs
    culd any one help me plz sir
    Live Cache Display Error log
    Name and Server              :  LCA - domain
    DBMRFC function             :  DBM_EXCUTE
    Command                        :  dbm_version
    error                                :  System Error
    Error Message*

    Hello Gerardo Navarrete,
    1) You are running the LiveCache instance.
                                          => You are SAP customer
    As SAP customer you have the option to create the OSS ticket, therefore we could
    logon to your system via OSS and take a look closer on the reported issue.
    Please create the ticket to the component 'BC-DB-LVC'.
    Or did you already report this problem in OSS ticket? What number?
    2) Please create the new<!> thread if you have the questions about the liveCache
        This thread is NOT related to the reported by you last problem.
    3) Did you see the message 'livecache lock server not accessible'  during the restart the liveCache in LC10?                            
    Please create the LEA connection in LC10 -> Integration as it's recommended in the liveCache installation guide, where you could see more info about new LEA connection. Test the connection in /ndb59.
    Did you set  the SLCA_LCK_SYNCOWNERS report under "Fllw-up Procg" at  "Start liveCache" on the "Administration report" tab for the LCA  connection in LC10 -> "Integration"?
    Thank you and best reagards, Natalia Khlopina

  • ZEN 8 GB connectivity prob

    Hey, I'm new to the forums here. I just got a new Creative mp3 player not too long ago ands its been great to use. Although one problem I did have with the previous ZEN V Plus I had and this one is that each time I goto plug my mp3 player into my PC and try to sync using WMP or Creai've Sync Manager it ends up disconnecting itself or ejecting, and then a few seconds later it reconnects. I've made sure that the cable I'm using has no broken wires or anything. I even tried using another cable too and it still happens.
    Help would be apreciated so I can fix this and continue to sync my music without interuption while it disconnects again!

    Well, instead of trying another PC, I pluged my mp3 player into one of the USB ports on my USB PCI card in the back. I can't goto school without my music so I thought I would try again and sync it, just not in the front USB ports. It hasn't cut out on me yet since I used the rear ports! As weird as that is it could be just that my PCI card is all that makes it work for some reason. The computers ports dont work but just the cards :S
    I was also looking at another topic about a simular problem... well not too the same, but it had said something about power levels affecting the connection. Maybe it is that the power output on my PC's USB ports are lower that normal and.. well, thats as far as I figure.
    So far I have sync'd more than 400 songs out of my 000 that I have without interuption!

  • Connect Prob

    hi
    when i connect my mp3 player to pc (usb) the computer not found anything but connect symbol appear on mp3 player. please help me? what should i do?
    my mp3 player model: MuVo TX FM

    Hi,
    Check the below case:
    [oracle@kor300949lx1 ~]$ sqlplus sys@orcl as sysdba
    SQL*Plus: Release 11.2.0.1.0 Production on Wed Mar 23 20:09:20 2011
    Copyright (c) 1982, 2009, Oracle. All rights reserved.
    Enter password:
    ERROR:
    ORA-12541: TNS:no listener
    Enter user-name:
    ERROR:
    ORA-01017: invalid username/password; logon denied
    Enter user-name:
    ERROR:
    ORA-01017: invalid username/password; logon denied
    SP2-0157: unable to CONNECT to ORACLE after 3 attempts, exiting SQL*Plus
    [oracle@kor300949lx1 ~]$ sqlplus sys/sys as sysdba
    SQL*Plus: Release 11.2.0.1.0 Production on Wed Mar 23 20:09:55 2011
    Copyright (c) 1982, 2009, Oracle. All rights reserved.
    Connected to:
    Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production
    With the Partitioning, OLAP, Data Mining and Real Application Testing options
    SQL> exit
    Disconnected from Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production
    With the Partitioning, OLAP, Data Mining and Real Application Testing options
    [oracle@kor300949lx1 ~]$ sqlplus "/as sysdba"
    SQL*Plus: Release 11.2.0.1.0 Production on Wed Mar 23 20:10:06 2011
    Copyright (c) 1982, 2009, Oracle. All rights reserved.
    Connected to:
    Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production
    With the Partitioning, OLAP, Data Mining and Real Application Testing options
    SQL> sho parameter %AUTHE%
    NAME TYPE VALUE
    os_authent_prefix string ops$
    remote_os_authent boolean FALSE
    In your case the above two parameters plays a major role.Study the below link for the complete details.Specially remote_os_authent.
    http://www.dba-oracle.com/security/local_os_authentication.htm
    When your ORACLE_SID is set no need to use @PROD.
    Hope it helps.
    Best regards,
    Rafi.
    http://rafioracledba.blogspot.com
    Edited by: Rafi (Oracle DBA) on Mar 23, 2011 7:15 AM

  • Weird microphone probs with Z10

    Hi there,
    as already said as part of another post:
    I´m having (also) trouble with my Z10 built in microphone.
    Audiorecording works fine and crispy clear, so I can assume the mic is just working, but when it comes to phone functionalities, this is where the weird behaviour starts!
    Initiating or answering phones directly in "handset" mode is no problem, but the mic is muted some how!
    Whe I switch to hands-free-speaker, my voice is directly loud and crystal clear again. When putting it back to handset mode, turning the speaker off, the mic immediately becomes muted again.
    Connecting a bluetooth headset (bose BT 002) or the factory issued speakerphones "re-connects" the mic directly again, loud, crisp and crystal clear.
    unplugging/unpairing these devices results in "strike" from the mic.
    I already took the battery out for several minutes, deactivated my alarm settings and unchecked the "automatic pair" checkbox in bluetooth, but it all had no effect so far!
    Since I use my Z10 also and mainly for business, this is pretty awkward
    PLZ anybody...HELP ME
    THX
    Paddy

    Thanks. Insight appreciated.

  • If you have a Slingbox and an Xbox 360, this will solve 360 connection prob

    I got my TC on Wednesday of this week and starting hooking everything up. I had a PS3, Wii, Xbox 360, Printer, and Slingbox Pro that I wanted to hook up. Slingbox, PS3, Wii, and Printer all work fine, but the Xbox would not cooperate as many of you have found out. So, I took my old linksys router that I was not going to use anymore, turned off its wireless functionality, so it simply acted like a signal pass through with multiple ethernet outputs. I unhooked the Slingbox from the part I speak of below, and attempted to use the linksys to split an incoming signal to the Slingbox and the Xbox 360, which ended up working like a charm.
    When I bought my Slingbox, I knew it was not going to be able to be close to my router, so I purchased one of their additional products (links below to products) call the Sling Link Turbo. Most of you are probably aware of this but for those of you that are not, it is a neat device that sends your internet signal through the electrical wiring in your house to a different location where it is plugged in another wall outlet. The catch is that both plugs have to be directly into a wall, it cannot go into a power strip or surge protector. I had this product by default on Wednesday and it helped me fix the problem, so it might benefit those of you that are interested to pick one up, the single port is not that expensive.
    http://www.slingmedia.com/go/slt
    http://www.slingmedia.com/go/slt4
    Moving on now, I connected the Slink Link Turbo to the back of the TC and plugged it in. Then I plugged its counterpart into the wall behind my TV so it could sit next to the Slingbox on top. I then ran an ethernet cord from the Sling Link Turbo to the WAN port on the Linksys router behind the TV. Then I ran an ethernet cord from the output ports on the linksys to the Xbox 360 and another cord to the Slingbox.
    This is where things got tricky because I had to forward the ports in order for the slingbox to work. I set the TC to reserve the IP 192.168.0.200 for the Linksys router. I set my linksys router to be have a static IP at 192.168.1.200 (not a typo) and I set the DNS Server to 192.168.0.1, which is the TC's router IP. Then I set the port forwarding on the TC to open port 5001 to 192.168.0.200 on all ports, Public and Private UDP and TCP. Then I set the Linksys router to open port 5001 to IP 192.168.1.253, which is the Slingbox.
    Do not set any static IP for the Xbox 360, it works great without it and if you set it it probably is not going to work.
    Now, hold down the reset button on the Slingbox for 20+ seconds to reset it completely, run through setup, takes about 3-5 minutes, and make the IP address 192.168.1.253 and leave the other settings as is. If it will not work, change the router to either IP 192.168.0.1 or 192.168.1.1, whichever one it did not show up as wanting to be. Then make sure the port is 5001 and you should be good to go on the Slingbox even remote viewing. If you have problems here, pop me an e-mail.
    Now for the Xbox 360, plug it in, turn it on, test connection settings, it should work perfectly on all accounts, mine has so far.
    I now have a PS3, Wii, Printer, Xbox 360, and Slingbox Pro running on the N connection, I did not have to downgrade the settings to b/g for the Xbox 360 to work. However, my linksys router is old and only supports G, so I'm not sure if my N signal translates through to the Slingbox and Xbox, but they still work great. And the rest of my house can use the N signal with no problem.
    If you have any problems please e-mail me and I will try to help as much as I can.
    Good luck.

    I have a question which I'm hoping you can answer. My dad lives in the states and has a slingbox connected. I live in another country and watch american tv through internet (i.e. through the slingbox he set up). I also have an xbox 360, which is connected to the TV in the living room. Do you know if it's possible to wirelessly stream the computer content (i.e. the slingbox content) to the tv in the living room through the xbox?
    Thanks
    Netta

  • Have you been getting timeouts and other weird connection issues lately?

    Internet connection has become a bit wonky as of late, have you been experiencing some or all of the following symptons?
    1) Most internet speed test sites just stop before completing as if they have timed out (i.e. speedtest.net).
    2) Sites will start loading quickly but then sometimes randomly stop and have to be manually refreshed.
    3) Downloads will randomly stop downloading for some moments before resuming (particularly from Steam)
    4) Tracert to some websites that were causing issues show timeouts on peering with Alter.net servers.
    Looks like there are some issues between Verizon and Alter.net (formerly MCI, now Verizon owned) in NY.... Any word on when we can expect a resolution? This is quite frustrating as it affects a good amount of traffic.

    I'm a little further east than you out here on Long Island, Touyats, but I've seen none of the issues you or the Original Poster here are experiencing.
    Assuming you're having the problems on a device connected to your router by Ethernet cable (WiFi opens up an entire range of other possible problems) you might try getting your router assigned a new WAN IP address. 
    If you want to give that a try, see this post for the steps involved:
    http://forums.verizon.com/t5/FiOS-Internet/How-am-I-able-to-change-my-ip-address/m-p/703336#M47733

  • At a loss: Audigy2 ZS Platinum & Klipsch DD5.1 connection prob

    I have read many forums, posts, etc. related to SPDIF, optical and digital out connection between Audigy2 ZS Platinum and Klipsch DD5. decoder and can't find a solution to my problem. I would like to play MP3's stereo x2 or 5. through my DD5. connected to Klipsch Promedia 5. speakers, all I can get is front L and R with nothing coming from the rear speaker. I have tried each of the three digital outputs, I have set SPDIF passthrough, digital output only, 5. as well as 2/2. speaker settings, and have toggled Enable CMSS 3D in the EAX console, also have Prologic enabled on the DD5. with no success. Does anyone have any suggestions? When the Promedia's are connected to the analog connections on the Audigy2 they sound great, MP3's through all speakers with CMSS 3D enabled, but I am using the Klipsch DD5. connected to my T.V., DVD etc. as my home theatre and would like to connect my PC this way as well. I have tried 3.5mm splitter on the back of the speakers and connected to the Audigy2 as well as the DD5. but this seems to cause a significant hum, interference etc. Any ideas?

    Saku746,
    What you are experiencing is normal for Digital connection such as coaxial/optical. You can get more information from the article at knowledgebase.
    http://us.creative.com/support/kb/article.asp?l=2&sid=5764
    Check your speaker whether it support Dolby Pro Logic II or other upmix matrix. If it does, then you can enable that to provide matrix of 5. to the speaker.
    Jason

Maybe you are looking for