My base station blink amber, but MBP says connected, My base station blink amber, but MBP says connected

I'm trying to install airport extreme, the base station blink orange, but my MBP says it's connected. Shouldn't the light on the base station be green also?

Open AirPort Utility and click Manual Setup
Click directly on the word "Status" (2nd line) and a window will open to explain why the AirPort Extreme is complaining
What does the message say? It might be something as simple as a notice that an update is available for your device.

Similar Messages

Have base station and added extender for downstairrs. Worked great upon initial setup, but now it won't connect despite an "excellent" signal. What's wrong? Thanks!!

Have base station and added extender for downstairs. Worked great upon initial setup, but now it won't connect despite an "excellent" signal. All i get is a blinking amber light; only get green if I bring it into the same room as the base. Both units are the latest models; purchased 2 months ago. What's wrong? Thanks!!

Power off both the AirPort Extreme and AirPort Express
Wait a minute
Power up the AirPort Extreme and let it run for a few minutes
Now locate the AirPort Express about half way between the AirPort Extreme and the general area where you need more wireless signal coverage, and report on your results.
The more that you can minimize obstructions between the AirPorts like walls, ceilings, etc. the better the wireless will operate.

HT1218 After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer. We still have wifi but cannot access the base station software.

After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer. We still have wifi but cannot access the base station software.

Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
Is there a way to resolve this issue?

HT4644 I'm experiencing a similar problem with an LG Flatron monitor which my MBP no longer recognizes I've tried installing the updates listed above but have not been succesful. Everytime I get a message saying that this software is not supported on my

I'm experiencing a similar problem with an LG Flatron monitor which my MBP no longer recognizes. I've tried installing all the updates listed above but have not been succesful. Everytime I get a message saying that this software is not supported on my system. Can anyone tell me why I can't install the updates?

Hello Philly,
I believe that when you reset your ipod(command given from the computer, right?) touch WHILE the ipod was updating, It cleared the system in the middle of writing files, thus corrupting(equivalent of cutting of in the middle of a sentence) the basic running system.
I suggest you go to an apple store and ask for a technical diagonosis in person. they may offer to help if the problem is fixable. If your ipod is still under warrenty, i would guess it would be free/low cost.
~Remember, I am just giving an educated guess on limited information

Can connect to internet, but software can't find base station

I bought the Airport express a few months ago to use with my stereo and IBM laptop. It took me a few tries to get it initially installed properly, but eventually did and everything worked great. A month or so ago I noticed that the tab to select "remote speakers" was not on my iTunes as it had been before. All of the settings were correct on my iTunes however so then I went to the AirPort Utility to check out the settings and the program said it could not find the base station. I tried to find the station on AirPort Set-up assistant. This program can find it but not connect to it (on the first page after the menu it shows the base station and when I hit "next" it can't connect to the station). All of this is really odd as I have internet access through this base throughout these problems. Any ideas what might be happening and how to fix it? I have reset the base station to factory settings numerous times, I have unplugged everything and restarted the whole process numerous times, I even left the base station unplugged for a week to let it relax. Still nothing works. I can connect to the internet through the station but can not find the station.
IBM T40 Windows XP Pro

Thanks for your help. I can manually connect to the internet but I can't figure out how to get iTunes to recognize that there are remote speakers as my computer can't recognize my base station. Is there a manual way to do this?
IBM T40 Windows XP Pro

I have an iPad that will not allow me to accept iCloud terms and conditions. It just says server not available. But on an annoyingly regular basis a pop up asks me to accept term and cond, I go to iCloud and try to but that is when it tells me it cannot c

I have an iPad that will not allow me to accept iCloud terms and conditions. It just says server not available. But on an annoyingly regular basis a pop up asks me to accept term and cond, I go to iCloud and try to but that is when it tells me it cannot connect to the server. Frustrating as I cannot get rid of the pop ups.

Thanks champion! Apple support is useless! Way too difficult to get anywhere with their "support"

Airport Express loses connection to base station

Airport Express second gen loses connection to base station, has to be reset.

Roger that. Late 2013 MBP 2.5 i5 4mb ram, 10.9.1 Mavericks, formatted and hand loaded after questionable upgrade load. Fast, flawless, no issues.
Airport Express configured to wirelessly extend existing network for the express purpose of supplying an analog
input to a stereo amplifier via airplay. No other devices are connected to the AE.
The WAP is a Century Link Actiontec C1000A VDSL2 physically located 6 feet from the AE with no obstructions.
There are no existing proximal fortuitous distortion or RF interference sources. Other 802.X networks near are
on non-conflicting channels. The WAP is less than six months old and has no issues.
The WAP is configured for MAC filtering with the SSID turned off. In the allow list are two iphones, a printer, two more MBPs and the Airport Express. One of the iphones is loaded with the Remote Ap which functions
flawlessly when the AE is connected.
The AE connects properly in the Extend Existing Network mode and performs as advertised as long as Air Play
and/or itunes is active.
Some time after music has ended, the MBP has gone to sleep, or been shut down ... the Airport Express loses its connection to the wireless network, with its amber light flashing.
Performing a reset and reconnecting is necesssary, and all works as advertised after. Subsequently,
sleep, inactivity, or shutdown will cause loss of connection again.
I am aware the AE can be connected with CAT6, but that is unnaceptable. If I had wanted to use wire I
would have plugged the MBP into the amplifier and saved $100.
My speculation is some sort of TCPIP flub in the design ... as in the AE does not natively transmit keep-alive
packets when it stops getting data from the Air Play computer. It would be easy to decide whether to fix
the problem or return an inadequately designed product ... if there were any information about it. No schematics, no operation description however leaves me only to say thank you for your time and hope
you have the solution.

Not able to connect to base station after last security update

Since the lastest update came out, I am no longer able to connect to the same base station I was once able to connect to. I get my DSL through SBC, and the station is a 2Wire Gateway. My mac mini still is able to connect, since it didn't have the security update. Did this happen to anyone else when they got the airport update?
Macbook Mac OS X (10.4.8)

I've got a similar problem. After the "AirPort Extreme Update 2007-001" was installed, i am only able to surf for approximately 30 minutes. Then my connections to the Internet stops working. When I disconnect and reconnect to my Accesspoint, my MacBookPro is unable to get an IP over DHCP. If I manually type an valid IP, the System Settings show that my Airport is connected to the Accesspoint and has connection to the Internet but it still doesn't work. The only thing that helps is to go in the "sleep mode" ("ruhezustand"), when i wake up my MBP i am able to surf for further 30 min, but even this doens't work always. When I tested the connection to the accesspoint under windows on the MBP everything worked fine.

I have firefox 10.0.2 installed but everytime I open up firefox I get a message that says I am not currently using this version and I need to update to the latest version and why won't firefox support printing mac coupons

my firefox info shows that I am using 10.0.2 but I keep getting a repeated message when I open it saying I'm not using the most recent version.
Even tho the mac coupon printer says firefox supports this install it doesn't allow me to print it.

Hi cleopt,
You may see that message below the Google search box on www.google.com/firefox which is the old Firefox default home page. That page is no longer being maintained by Google.
You should try changing your home page to:
about:home
If you don't know how to change the home page, you should take a look at the Knowledge Base article [[How to set the home page]].
Hopefully this helps

I have a brought cd that is in the store but when i go to import it it does not allow says to have to manually type heaps of songs. there are cds saying the same!

i have a brought cd that is in the itunes store but when i go to add to to my list is says not on net data base. my own copy i brought! how do i solve it i do not want to type over 50 songs in to computer.

Hi dones49,
It sounds like your issue here is that iTunes can not find the files for some of the songs you have brought into it. This happens occasionally even if the songs have not been moved from the location that iTunes places them on import or purchase. When you try to use the song, iTunes prompts you to find the file, as you have seen.
To find the file, use the information in this article to navigate through the iTunes media folders -
Locate and organize your iTunes files
If you are still unable to locate the files, you may need to download them from the iTunes store again, or rip them from your CDs. See this article for assistance with downloading your past purchases -
Download past purchases
Thanks for using Apple Support Communities.
Best,
Brett L

Itunes radio error on ios7 says unable to create station

I have had IOS 7 on my IPHONE 4 for a few days now. The first day my ITUNES radio worked fine but since then it say Unable to Create Station when I try to use it. I have reset phone, reset network and everything and still no success. HELP?!!

I tried lots of combinations
but this one worked
1) sign out of itunes
2) power-down phone
3) switch phone back on
4) sign in
bingo

I keep being asked to update my Safari but when I do a Software update it scans but never gives me a list and just says no new updates. Help please!

I keep being asked to update my Safari but when I do a Software update it scans but never gives me a list and just says no new updates. Help please!

There are no updates to either OS 10.5.8 or Safari 5.0.6.
If you need a later version of Safari you must first upgrade your operating system to a later version of OS X.

I just order 8 calendars from iPhoto and they came to me fine. Now I need to order two more but when I go thru the process I get a message saying:unable to assemble calendar. There is a probleme with the photo with the file name"(Null)" more........ .

Would someone be able to explain to me the following issue with Iphoto?
I ordered 8 same calendars for my soccer team and received them fine. Although a couple of pictures on it are a little off (out of focus). I need to order two more of the same calendars but when I go thru the process ireceive an error message saying:
"Unable to to assemble calendar" There is a problem with the photo with the file name "(Null)" The full resolution version of this photo either cannot be located or is corrupt. Please replace this photo or delete it from your calendar.
How can I fine this "corrupt" photo? How did it go thru with the first batch of calendars but won't go thru now?
Thank you for your help.

Apply the two fixes below in order as needed:
Fix #1
Launch iPhoto with the Command+Option keys held down and rebuild the library.
Since only one option can be run at a time start
with Option #4 and then #1 as needed.
Fix #2
Using iPhoto Library Manager to Rebuild Your iPhoto Library
1 - download iPhoto Library Manager and launch.
2 - click on the Add Library button, navigate to your Home/Pictures folder and select your iPhoto Library folder.
3 - Now that the library is listed in the left hand pane of iPLM, click on your library and go to the File ➙ Rebuild Library menu option.
4 - In the next window name the new library and select the location you want it to be placed.
5 - Click on the Create button.
Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments. However, books, calendars, cards and slideshows will be lost. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.
OT

Adobe Creative Cloud because I do not get After Effects among others but I try to install software from the page but I give After Effects download shareware and says downloading but nothing comes give him retrying but nothing even leave the application of

if you can help me please alguin
Adobe Creative Cloud because I do not get After Effects among others but I try to install software from the page but I give After Effects download shareware and says downloading but nothing comes give him retrying but nothing even leave the application of Adobe Creative but nothing help

Without proper system info and otehr technical details nobody can tell you anything.
Mylenium

I have adobe editions 4.0 and I've been trying to get library books on my kobo for over 2 hours! The book goes onto my Kobo fine, but when I try to open in on my kobo it says, "Oops! The document couldn't be opened. It's protected by ADRM and is not curre

I have adobe editions 4.0 and I've been trying to get library books on my kobo for over 2 hours! The book goes onto my Kobo fine, but when I try to open in on my kobo it says, "Oops! The document couldn't be opened. It's protected by ADRM and is not currently authorized for use with your Adobe ID." It does it with every single book. I've never had this problem before. I've tried everything! Please help.

same problem for me. I am using abe edition 3 as I don't think 4 can be used with kobo. Book has been downloaded to kobo but it can't be read as it is not authorised.Help please

I pad has been disabled as kids typing in wrong passcode to many times. I pad says connect to I tunes, tried to but pc asks to put in passcode to enter I tunes but as its disabled I can't type in a passcode. Any ideas ?

iPad has been disabled as kids have typed in wrong passcode too many times. Have tried to connect to iTunes to restore it but can't as PC says to enter passcode but I obviously can't as iPad is disabled. Any ideas ?

You have to restore the device within iTunes. You want to use the same computer that you always sync with so that you can restore your app data and settings. You can restore with any other computer, but you will lose everything on the iPad.
You will need to restore using Recovery Mode. You can read about it here.
http://support.apple.com/kb/ht4097
Recovery Mode Instructions
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
Use iTunes to restore iPad.

My base station blink amber, but MBP says connected, My base station blink amber, but MBP says connected

Similar Messages

Maybe you are looking for