My ipad only showes the apple and it does not start up

when i turn on my ipad the only thing on the screen is the apple logo and this happened after updating to ios 7.0.4

My ipad mini opens, I can put in the passcode. The screen goes to my wallpaper (no icons show up) for a few seconds, then the screen goes back to the apple screen. I have done a soft reboot (off and on),
and a hard reboot (holding down the two buttons)....and nothing....same problem. I haven't found anyone that has had this problem on the internet. I took it back to Best Buy where I purchased it, and they had not seen the problem before either.

Similar Messages

HT201210 the screen on my ipod touch will only show the apple icon it will not turn all the way on

the screen on my ipod touch only shows the apple logo.it will not shut off or turn all the way on and when plugged into itunes it will not allow the newest update

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

HT3302 My iPod Touch fell into the washer and now does not start. What can I do to fix it?

My iPod Touch fell into the washer and now does not start. What can I do to fix it?

If it is totally dry:
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
Apple will exchange your iPod for a refurbished one for this price. They do not fix yours.
Apple - iPod Repair price

Update the iPad 2 with new iOS uppgrade, but after the screen only show the apple and nothing else. has been the case since yesterday. have turned off the iPad and turned it on again many times, but still only apple shown. What should I do?

UPdate the iPad wjith new iOS upgrade that where shown under settings on the iPad, but after I did the upgrade the screen has only shown the apple and I can't get back. This has been the case since yesterday. Have turned off t.he iPad many times, but every timebwkhen Ibturn it on again the screen onöy show the apple icon and nothing else happends. What should I do? Anyone having the same problem and how can this be solved?

Did you try to connect in recovery mode, explained in this article?
iOS: Unable to update or restore

My Macbook Pro shows the apple and spinning wheel at start up but won't continue startup. Any Help would be appreciated.

My Macbook Pro shows the Apple and spinning wheel at startup but will not continue the startup. Does anybody know how to get past this, so the computer continues to startup?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. The easiest way to deal with the problem is to boot from an external drive, or else to use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 9
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Repeat Step 9, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

My ihone only show the apple and then turn off again

my iphone only show the silver apple when i turn on ,and it need to be when i charging, after couple second it went off again. it also wont show up in itune

Could be faulty battery. Make Genius reservation and take iPhone to Apple Store for free quick battery diagnostic testing.

HT1414 My ipad only showes the apple it does not start up

When I turn on my ipad all i get is the apple, it does not turn on completely.

Did you try rebooting the iPad?
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

I had my iphone connected to computer and was downloading updates. an error ocured now the phone diplay only shows the apple and the little cirkel that tells you it is busy. error number is 0x8000065. i can't put it off. reacts to nothing anymore, ???

Problem while downloading latest updates with iphone 4. error number 0xE8000065. The computer cant find the phone and the phone doesnt react on anything anymore. display shows apple and being busy cirkel.

Follow the instructions in this support article:
http://support.apple.com/kb/TS3221

HT201263 My iPod Touch shows the Apple logo but does not respond to holding the home and lock buttons or being plugged in. iTunes does not recognize it either

I plugged my iPod into my computer to retore it and proceeded to do so as told. The only thing that happened after that was that the Apple logo keeps showing up and nothing else. My computer/iTunes no longer recognizes my iPod either.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

IDVD Icon does not appear in the dock and iDVD does not start.

I have been trying to solve the above problem. I have archived and installed OSX upto 10.4.9 and reinstalled iLife 06 and have had no success in getting iDVD to run. All I see in the dock is an icon saying "application".
Would welcome some suggestions - will I have do a total reinstall? Hope not.
Many thanks.
Chris Fox[

Welcome to the forums.
If you go to the Applications folder, what happens if you try to start iDVD directly? Your Quicktime also needs to be updated to be compatible with iLife6 (beware though that you'll lose your Pro capabilities if you're jumping from QT6 to 7).
John

HT4623 My Ipad turns on but it only shows the apple it wont open de window

My Ipad turns on but it wont shoe the window it only shows the apple and stays there

Peluso123-
One thing you can try is to reset (reboot) your iPad. Hold both the Home and Sleep buttons for several seconds until the Apple logo appears. If the logo is already there, keep holding for at least 20 seconds. Ignore the "Slide to power off" arrow if it appears. If you are successful, the iPad will restart after a couple of minutes. Resetting this way will not hurt anything, and sometimes clears up mysterious problems.
If that does not work or help, see if this article helps: <iOS: Unable to Update or Restore>.
Fred

HT4972 My IPad 2, IPhone 3GS ans iPod no longer work with apple TV, I have 2 apple TV in my house and for he last 3 weeks the iPod was the only one we could use for appleTV now none of them works, the apple TV icon does not show up any more. Re-startedev

My IPad 2, IPhone 3GS ans iPod no longer work with apple TV, I have 2 apple TV in my house and for he last 3 weeks the iPod was the only one we could use for appleTV now none of them works, the apple TV icon does not show up any more. Re-started everything.

Ok thank you so much, for your timely response.
RESPONSES:
1)   When I set up my iMac, I did not transfer any data directly from my windows PC. I simply used the same iTunes login and account. I have access to all of the files via the "Purchased" section of the iTunes store. If I click "Download Previous Purchases" text, I can download ALL of the purchases I have ever made.
2)   I have the Apple TV 2, so good news, question answered. I thought maybe it was the Apple TV 1, but it is the Black model, so bam. Good response for you. Well the whole damned reply is an awesome response, just pointing out that one piece of awesome. I stated that it was an Apple TV 2, and yet you were still good enough to figure I could be mistaken, and provide me with knowleedge just incase.
QUESTIONS:
3)   So can my iMac not stream the data directly from itunes, without download? Apple TV can, but perhaps that is something among many things that maker it unique, and awesome.
SERIOUSLY.... THANK YOU...
I work in the computer support section for the Military. The only problem is we use Windows , lol. Well that and i've been gone for nearly 6 months on recover. I go back next month though I hope. But working in that field gives me the abilty to judge responses that run inside the same vein. Your response was so awesome that I half thought I might have written it myself.

While updating software of Ipad, it stop working and only shows the Apple on screen. How can I recover?

While I was updating the software of my IPad, it stopped working and only shows the apple logo. How can I recover my IPad?

Have you tried a reset ? Press and hold both the sleep and home buttons for about 10 to 15 seconds, after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

Tried to open an app and my iPad gen one froze. It only shows the apple on black screen and will show the operating wheel sometimes and while plugged in it will beep every few minutes. Will not load one show anything on screen but the small white apple.

Tried to open an app and my iPad gen one froze. It only shows the apple on black screen and will show the operating wheel sometimes and while plugged in it will beep every few minutes. Will not load one show anything on screen but the small white apple.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

My iPad air would not start. Only show the apple logo then no reaction after that.

My iPad air would not start. Only show the apple logo then no reaction after that. This is already the 2nd time. Last time I sent back to the service center and they said it is the system problem and reset the system and charge me for the service because they said it is not a hardware problem. It happened less then 30 days and same problem again. Can someone please send me the hard-reset step so I can try myself before I send back to the service center again? thanks

Here's the hard reset info:
http://www.hard-reset.com/apple-ipad-hard-reset.html
Post something about what happened with your visit.

My ipad only showes the apple and it does not start up

Similar Messages

Maybe you are looking for