My Macbook Pro suddenly became really slow
3 Days ago my Macbook Pro suddenly became really slow. I can't run anything without my computer freezing. I've had my Macbook Pro since mid-2012 (21 months). The first thing i did was check my activity monitor, which said that I was apparently using 4 GB (half) of my Macbook Pro's RAM, even though nothing was running. The process that was using the most RAM was kernal.task, which was only around 600mb of RAM. All the processes RAM amounts only added up to around 1 GB, not four. I can't even open safari without my computer freezing. The amount of RAM being "used" on my computer slowly started to increase, even though nothing was running, until it got to all 8 GB being used. When i restart my computer, it goes back to 4 GB and starts to rise again. My processor, on the other hand, is doing nothing. Its acting normally. How do i get my computer back to its usual performance?
Hardware Specifications
13-inch Mid-2012 Macbook Pro
Processor: 2.9 GHz Intel Core i7
Memory: 8 GB 1600 MHz DDR3
Graphics: Intel HD Graphics 4000 1024 MB
750 GB HDD
OS X 10.9.2
Since you are using Mavericks OS, the amount of RAM being used is inconsequential but the 'pressure' is. If green is showing then the RAM usage is normal. This is a change fro prior OSX's.
The usual problem will lie with the HDD, It may be too full or needs to be repaired or replaced. Go into OSX recovery and select from the 4 option menu Disk Utility. Choose First Aid and run Verify and Repair.
(Start the MBP with the OPTION key down and select the recovery partition)
If that does not solve the problem, try a safe boot:
http://support.apple.com/kb/ht1564
If the MBP responds 'normally' that usually indicates that there is a third part application that is causing the problem. They have to bedeleted and reinstalled in a systematic way so that you can identify the culprit.
Ciao.
Similar Messages
-
My MacBook Pro suddenly became very slow, cursor responding slowely
My MacBook Pro suddenly became very slow, cursor responding slowely
1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the request of a stranger on a public message board. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed: Copy a line of text from this web page into the window of another application. Wait for the script to run. It usually takes a few minutes. Then paste the results, which will have been copied automatically, back into a reply on this page. The sequence is: copy, paste, wait, paste again. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin; clear; Fb='%s\n\t(%s)\n'; Fm='\n%s\n\n%s\n'; Fr='\nRAM details\n%s\n'; Fs='\n%s: %s\n'; Fu='user %s%%, system %s%%'; AC="com.autodesk.AutoCAD com.evenflow.dropbox com.google.GoogleDrive"; H='^[[:space:]]*((127\.0\.0\.1|::1|fe80::1%lo0)[[:space:]]+local|(255\.){3}255[[:space:]]*broadcast)host[[:space:]]*$'; NS=networksetup; PB="/usr/libexec/PlistBuddy -c Print"; A () { [[ a -eq 0 ]]; }; M () { find -L "$d" -type f | while read f; do file -b "$f" | egrep -lq XML\|exec && echo $f; done; }; AT () { o=`file -b "$1" | egrep -v '^(A.{16}t$|cann)'`; Ps "${1##*/} format"; }; Pc () { o=`grep -v '^ *#' "$2"`; l=`wc -l <<< "$o"`; [[ l -gt 25 ]] && o=`head -n25 <<< "$o"`$'\n'"[$((l-25)) more line(s)]"; Pm "$1"; AT "$1"; }; Pm () { [[ "$o" ]] && o=`sed -E '/^ *$/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/(\/Users\/)[^/]+/\1-/g' <<< "$o"` && printf "$Fm" "$1" "$o"; }; Pp () { o=`$PB "$2" | awk -F'= ' \/$3'/{print $2}'`; Pm "$1"; }; Ps () { o=`echo $o`; [[ ! "$o" =~ ^0?$ ]] && printf "$Fs" "$1" "$o"; }; R () { o=; [[ r -eq 0 ]]; }; SP () { system_profiler SP${1}DataType; }; id -G | grep -qw 80; a=$?; A && sudo true; r=$?; t=`date +%s`; clear; { A || echo $'No admin access\n'; A && ! R && echo $'No root access\n'; SP Software | sed -n 's/^ *//;5p;6p;8p'; h=(`SP Hardware | awk '/ Id/{print $3}; /Mem/{print $2}'`); o=$h; Ps "Model"; o=$((h[1]<4?h[1]:0)); Ps "Total RAM (GB)"; o=`SP Memory | sed '1,5d;/[my].*:/d'`; [[ "$o" =~ s:\ [^O]|x([^08]|0[^2]|8[^0]) ]] && printf "$Fr" "$o"; o=`SP Diagnostics | sed '5,6!d'`; [[ "$o" =~ Pass ]] || Pm "POST"; p=`SP Power`; o=`awk '/Cy/{print $NF}' <<< "$p"`; o=$((o>=300?o:0)); Ps "Battery cycles"; o=`sed -n '/Cond.*: [^N]/{s/^.*://p;}' <<< "$p"`; Ps "Battery condition"; for b in FireWire Thunderbolt USB; do o=`SP $b | sed -En '/:$/{s/ *:$//;x;s/\n//;s/\n.*//;/\)/p;};/^ *(V.+ [0N]|Man).+ /{s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};/Apple|Broadcom|Genesy|Intel|SMSC/{s/.//g;h;}'`; Pm $b; done; o=`pmset -g therm | sed 's/^.*C/C/'`; [[ "$o" =~ No\ th|pms ]] && o=; Pm "Thermal conditions"; o=`pmset -g sysload | grep -v :`; [[ "$o" =~ =\ [^GO] ]] || o=; Pm "System load advisory"; o=`nvram boot-args | awk '{$1=""; print}'`; Ps "boot-args"; fdesetup status | grep -q On && o=on || o=; Ps "FileVault"; a=(/ ""); A=(System User); for i in 0 1; do o=`cd ${a[$i]}L*/Lo*/Diag* || continue; for f in *.{cr,h,pa,s}*; do [[ -f "$f" ]] || continue; d=$(stat -f%Sc -t%F "$f"); [[ "$f" =~ h$ ]] && grep -lq "^Thread c" "$f" && f="$f *"; echo "$d ${f%%_2*} ${f##*.}"; done | sort | tail`; Pm "${A[$i]} diagnostics"; done; grep -lq '*$' <<< "$o" && printf $'\n\t* Code injection\n'; o=`syslog -F bsd -k Sender kernel -k Message CReq 'caug|GPU |hfs: Ru|last value [1-9]|n Cause: -|NVDA\(|pagin|proc: t|Roamed|rror|ssert|Thrott|timed? ?o|WARN' -k Message Ane 'SMC:' | tail -n25 | awk '/:/{$4=""; $5=""};1'`; Pm "Kernel messages"; o=`df -m / | awk 'NR==2 {print $4}'`; o=$((o<5120?o:0)); Ps "Free space (MiB)"; o=$(($(vm_stat | awk '/eo/{sub("\\.",""); print $2}')/256)); o=$((o>=1024?o:0)); Ps "Pageouts (MiB)"; s=( `sar -u 1 10 | sed '$!d'` ); [[ s[4] -lt 85 ]] && o=`printf "$Fu" ${s[1]} ${s[3]}` || o=; Ps "Total CPU usage" && { s=(`ps acrx -o comm,ruid,%cpu | sed '2!d'`); n=$((${#s[*]}-1)); c="${s[*]}"; o=${s[$n]}%; Ps "CPU usage by process \"${c% ${s[$((n-1))]}*}\" with UID ${s[$((n-1))]}"; }; s=(`top -R -l1 -n1 -o prt -stats command,uid,prt | sed '$!d'`); n=$((${#s[*]}-1)); s[$n]=${s[$n]%[+-]}; c="${s[*]}"; o=$((s[$n]>=25000?s[$n]:0)); Ps "Mach ports used by process \"${c% ${s[$((n-1))]}*}\" with UID ${s[$((n-1))]}"; o=`kextstat -kl | grep -v com\\.apple | cut -c53- | cut -d\< -f1`; Pm "Loaded extrinsic kernel extensions"; R && o=`sudo launchctl list | awk 'NR>1 && !/0x|com\.(apple|openssh|vix\.cron)|org\.(amav|apac|calendarse|cups|dove|isc|ntp|openld|post[fg]|x)/{print $3}'`; Pm "Extrinsic daemons"; o=`launchctl list | awk 'NR>1 && !/0x|com\.apple|org\.(x|openbsd)|\.[0-9]+$/{print $3}'`; Pm "Extrinsic agents"; o=`for d in {/,}L*/Lau*; do M; done | egrep -v 'com\.apple\.(CSConfig|server)' | while read f; do ID=$($PB\ :Label "$f") || ID="No job label"; printf "$Fb" "$f" "$ID"; done`; Pm "launchd items"; o=`for d in /{S*/,}L*/StartupItems; do M; done`; Pm "Startup items"; sys=`pkgutil --regexp --only-files --files com.apple.pkg.* | sort | uniq | sed 's:^:/:'`; b=`sed -E '/^.+Lib.+\/Contents\/Info.plist$/!d;s/\/Info.plist$//;/Contents\/./d' <<< "$sys"`; l=`egrep '^/usr/lib/.+dylib$' <<< "$sys"`; [[ "$b" && "$l" ]] && { o=`find -L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo}* -type d -name Contents -prune | grep -Fv "$b" | while read d; do test -f "$d/Info.plist" || continue; ID=$($PB\ :CFBundleIdentifier "$_") || ID="No bundle ID"; printf "$Fb" "${d%/Contents}" "$ID"; done`; Pm "Extrinsic loadable bundles"; o=`find /usr/lib -type f -name *.dylib | grep -Fv "$l"`; Pm "Extrinsic shared libraries"; :; } || echo $'\nReceipts missing'; o=`for e in INSERT_LIBRARIES LIBRARY_PATH; do launchctl getenv DYLD_$e; done`; Pm "Inserted dylibs"; o=`find -L {,/u*/lo*}/e*/periodic -type f -mtime -10d`; Pm "Modified periodic scripts"; o=`scutil --proxy | grep Prox`; Pm "Proxies"; o=`scutil --dns | awk '/r\[0\] /{if ($NF !~ /^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./) print $NF; exit}'`; i=`route -n get default | awk '/e:/{print $2}'`; I=`$NS -listnetworkserviceorder | sed -En '/ '$i'\)$/{x;s/^\(.+\) //p;q;};x'`; n=`$NS -getdnsservers "$I" | awk '!/^T/{printf "not "; exit}'`; Ps "DNS (${n}from DHCP)"; o=`$NS -getinfo "$I" | awk '/k:/{if ($3 !~ "(255\.){3}0") print}; /v6:/{if ($2 !~ "A") print}'`; Pm "TCP/IP"; R && o=`sudo profiles -P | grep : | wc -l`; Ps "Profiles"; f=auto_master; [[ `md5 -q /etc/$f` =~ ^b166 ]] || Pc $f /etc/$f; for f in fstab sysctl.conf crontab launchd.conf; do Pc $f /etc/$f; done; f=/etc/hosts; Pc "hosts" <(egrep -v "$H" $f ); AT $f; Pc "User launchd" ~/.launchd*; R && Pc "Root crontab" <(sudo crontab -l); Pc "User crontab" <(crontab -l); R && o=`sudo defaults read com.apple.loginwindow LoginHook`; Pm "Login hook"; LD="$(`find /S*/*/F* -type f -name lsregister | head -n1` -dump)"; o=`for ID in $AC; do [[ "$LD" =~ $ID ]] && echo $ID; done`; Pm "Application check"; Pp "Global login items" /L*/P*/loginw* Path; Pp "User login items" L*/P*/*loginit* Name; Pp "Safari extensions" L*/Saf*/*/E*.plist Bundle | sed -E 's/(\..*$|-[1-9])//g'; o=`find ~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \) | wc -l`; Ps "Restricted user files"; cd; o=`find . -maxdepth 1 -exec basename {} + | while read f; do [[ ("$f" =~ ^\.. && ! "$f" =~ ^\.(adobe|android|bash.+|CFU.+|cache|config|cups|dropbox|DS_Store|font.+|git.+|profile|rnd|sh_.+|ssh|subv.+|Trash(es)?|zprofile|zsh.+)$) || ($(stat -f%f "$f") -ge 32768 && "$f" != Library) ]] && ls -Fd "$f"; done`; Pm "Hidden user files"; o=`SP Fonts | egrep 'id: N|te: Y' | wc -l`; Ps "Font problems"; o=`find L*/{Con,Pref}* -type f ! -size 0 -name *.plist | while read f; do plutil -s "$f" >&- || echo $f; done`; Pm "Bad plists"; d=(Desktop L*/Keyc*); n=(20 7); for i in 0 1; do o=`find "${d[$i]}" -type f -maxdepth 1 | wc -l`; o=$((o<=n[$i]?0:o)); Ps "${d[$i]##*/} file count"; done; o=; [[ UID -eq 0 ]] && o=root; Ps "UID"; o=$((`date +%s`-t)); Ps "Elapsed time (s)"; } 2>/dev/null | pbcopy; exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste (command-V). The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "syntax error," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Terms of Use of the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
MacBook Pro suddenly runs really slow
I have a mid-2012 13" non-retina macbook pro that I bought September 22, 2013 and Friday it started running really slow, like it takes 5 minutes for it to startup and two minutes to log in. I opened up the console and I get all these errors and I've reset the SMC and PRAM and I've also restored from time capsule backup and still no use. What do I do? I don't care if I have to wipe my hard drive since all my stuff is backed up to iCloud and my Time Capsule. Here's what comes up in the console: 4/6/14 12:03:54.000 PM kernel[0]: SMC::smcReadKeyAction ERROR F1Mn kSMCBadArgumentError(0x89) fKeyHashTable=0x0xffffff801e1fd000
4/6/14 12:03:43.189 PM awacsd[63]: InnerStore GetWakeInfoForZone: no external port for 1980574548.members.btmm.icloud.com.
And they're a continuous string of errors. I've also performed a disk utility and nothing came up in red.Well you're helpful lol. I contacted them twice and they weren't of much help. I found out what was causing the issue. I had the program MacFanControl installed and when I went to uninstall it, I just dragged it to the trash can and emptied it. I went to the website where I got it and followed the instructions on how to remove it and now its running like it did before.
-
The monitor of my MacBook Pro suddenly became all black, I tried to reset but it did not work, what should I do? Why does this happen?
I advise to reply to the one you want to reply to.
You have had good information here. I will not repeat that here.
I would like to add:
you have incompatible software: start in SafeMode, read Woodmeister and see if it is free of issues.
Akamai is crap software needed or not, Huawei the same.
It is very possible that the keygenerator you used for generating a key for some softwares has infected your mac.
The non-regular software with the false key(s) are not compatible probably or generate malware. Luckily you can not update them automatically because the keygenerator blocked the software for contacting the developer... I propose to consider getting rid of those softwares by really good uninstalling.
You have a beautiful mac, don't degenerate it with crapped software. There are alternatives for expensive software, for example Adobe Photoshop has a free alternative (with a less beautiful interface) in GIMP. And so on.
Lex -
Problem description:
My MacBook Pro is running really slow. Applications won’t open or take up to 10 min.
EtreCheck version: 2.1.5 (108)
Report generated December 27, 2014 at 9:15:58 PM CST
Click the [Support] links for help with non-Apple products.
Click the [Details] links for more information about that line.
Click the [Adware] links for help removing adware.
Hardware Information: ℹ️
MacBook Pro (13-inch, Late 2011) (Verified)
MacBook Pro - model: MacBookPro8,1
1 2.4 GHz Intel Core i5 CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1333 MHz ok
BANK 1/DIMM0
2 GB DDR3 1333 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 3000 - VRAM: 384 MB
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.1 (14B25) - Uptime: one day 6:55:8
Disk Information: ℹ️
TOSHIBA MK5065GSXF disk0 : (500.11 GB)
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
HD (disk1) / [Startup]: 498.88 GB (5.04 GB free) (Low!)
Core Storage: disk0s2 499.25 GB Online
MATSHITADVD-R UJ-8A8
USB Information: ℹ️
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/System/Library/Extensions
[loaded] com.epson.driver.EPSONProjectorUDAudio (1.30 - SDK 10.4) [Support]
[not loaded] com.seagate.driver.PowSecDriverCore (5.2.6 - SDK 10.4) [Support]
/System/Library/Extensions/Seagate Storage Driver.kext/Contents/PlugIns
[not loaded] com.seagate.driver.PowSecLeafDriver_10_4 (5.2.6 - SDK 10.4) [Support]
[not loaded] com.seagate.driver.PowSecLeafDriver_10_5 (5.2.6 - SDK 10.5) [Support]
[not loaded] com.seagate.driver.SeagateDriveIcons (5.2.6 - SDK 10.4) [Support]
Problem System Launch Agents: ℹ️
[killed] com.apple.CallHistoryPluginHelper.plist
[killed] com.apple.coreservices.appleid.authentication.plist
[killed] com.apple.icloud.fmfd.plist
[killed] com.apple.telephonyutilities.callservicesd.plist
4 processes killed due to memory pressure
Problem System Launch Daemons: ℹ️
[killed] com.apple.ctkd.plist
[killed] com.apple.icloud.findmydeviced.plist
[killed] com.apple.ifdreader.plist
[killed] com.apple.nehelper.plist
[killed] com.apple.wdhelper.plist
[running] com.seagate.TBDecorator.plist [Support]
5 processes killed due to memory pressure
Launch Agents: ℹ️
[not loaded] com.adobe.AAM.Updater-1.0.plist [Support]
[loaded] com.carbonite.launchd.carbonitealerts.plist [Support]
[running] com.carbonite.launchd.carbonitestatus.plist [Support]
[loaded] com.coupons.coupond.plist [Support]
[loaded] com.hp.help.tocgenerator.plist [Support]
[loaded] com.trendmicro.itis.dca.plist [Support]
[running] com.trendmicro.itis.uimgmt.agent.plist [Support]
Launch Daemons: ℹ️
[failed] com.adobe.fpsaud.plist [Support]
[running] com.carbonite.launchd.carbonitedaemon.plist [Support]
[loaded] com.microsoft.office.licensing.helper.plist [Support]
[running] com.trendmicro.icore.av.plist [Support]
[running] com.trendmicro.icore.main.plist [Support]
[running] com.trendmicro.icore.wp.plist [Support]
[running] com.trendmicro.itis.plugin.plist [Support]
User Launch Agents: ℹ️
[loaded] com.adobe.AAM.Updater-1.0.plist [Support]
[loaded] com.google.keystone.agent.plist [Support]
[invalid?] com.jdibackup.JustCloud.autostart.plist [Support]
[invalid?] com.jdibackup.JustCloud.backupstart.plist [Support]
[loaded] com.trendmicro.itis.uninstaller.plist [Support]
User Login Items: ℹ️
iTunesHelper Application (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
bomgar-scc-20130819-104735 UNKNOWN (missing value)
bomgar-scc-20130905-143949 UNKNOWN (missing value)
USB Display Agent Application (/Applications/USB Display/USB Display.app/Contents/Resources/USB Display Agent.app)
WDDriveUtilityHelper Application (/Applications/WD Drive Utilities.app/Contents/Resources/WDDriveUtilityHelper.app)
WDSecurityHelper Application (/Applications/WD Security.app/Contents/Resources/WDSecurityHelper.app)
USB Display Agent Application (/Applications/USB Display/USB Display.app/Contents/Resources/USB Display Agent.app)
bomgar-scc-20130819-104735 UNKNOWN (missing value)
bomgar-scc-20130905-143949 UNKNOWN (missing value)
HP Scheduler Application (/Library/Application Support/Hewlett-Packard/Software Update/HP Scheduler.app)
HP Product Research Application (/Library/Application Support/Hewlett-Packard/Customer Participation/HP Product Research.app)
Internet Plug-ins: ℹ️
SharePointBrowserPlugin: Version: 14.4.7 - SDK 10.6 [Support]
FlashPlayer-10.6: Version: 15.0.0.223 - SDK 10.6 [Support]
CouponPrinter-FireFox_v2: Version: 5.0.5 - SDK 10.6 [Support]
Flash Player: Version: 15.0.0.223 - SDK 10.6 Mismatch! Adobe recommends 16.0.0.235
QuickTime Plugin: Version: 7.7.3
Default Browser: Version: 600 - SDK 10.10
User internet Plug-ins: ℹ️
npBcsMcTcIO: Version: Unknown [Support]
Safari Extensions: ℹ️
Trend Micro Toolbar [Installed]
3rd Party Preference Panes: ℹ️
Carbonite [Support]
Flash Player [Support]
Paragon NTFS for Mac ® OS X [Support]
Seagate Dashboard for Mac OSX [Support]
Time Machine: ℹ️
Skip System Files: NO
Mobile backups: ON
Auto backup: YES
Volumes being backed up:
HD: Disk size: 498.88 GB Disk used: 493.84 GB
Destinations:
Jens Seagate Backup [Local]
Total size: 999.86 GB
Total number of backups: 6
Oldest backup: 2014-06-24 10:33:56 +0000
Last backup: 2014-12-17 17:14:18 +0000
Size of backup disk: Too small
Backup size 999.86 GB < (Disk used 493.84 GB X 3)
My Passport for Mac [Local]
Total size: 2.00 TB
Total number of backups: 14
Oldest backup: 2013-08-21 19:19:35 +0000
Last backup: 2014-12-19 11:44:23 +0000
Size of backup disk: Excellent
Backup size 2.00 TB > (Disk size 498.88 GB X 3)
Top Processes by CPU: ℹ️
6% coreaudiod
5% CarboniteDaemon
4% iMovie
3% JustCloud
3% Wondershare Player
Top Processes by Memory: ℹ️
335 MB iPhoto Library Manager
180 MB Finder
142 MB iMovie
70 MB Preview
51 MB Microsoft Word
Virtual Memory Information: ℹ️
149 MB Free RAM
1.04 GB Active RAM
897 MB Inactive RAM
1.17 GB Wired RAM
30.53 GB Page-ins
1.42 GB Page-outs
Diagnostics Information: ℹ️
Dec 26, 2014, 05:17:12 PM /Library/Logs/DiagnosticReports/iPhoto_2014-12-26-171712_[redacted].cpu_resourc e.diag [Details]
Dec 26, 2014, 03:47:17 PM /Library/Logs/DiagnosticReports/CarboniteDaemon_2014-12-26-154717_[redacted].cp u_resource.diag [Details]
Dec 26, 2014, 02:22:01 PM Self test - passed
Dec 26, 2014, 11:48:03 AM /Library/Logs/DiagnosticReports/CarboniteDaemon_2014-12-26-114803_[redacted].cp u_resource.diag [Details]You have nearly run out of disk space. Either purchase a larger one or start cleaning out the one you have?
-
After ransomeware on my macbook pro it is really slow, is there anything i can do to improve this?
After getting ransomware on my macbook pro it is really slow, what can i do to improve this? I cleared it from the screen by restarting and holding shift
If you held down the shift key at startup then you are now booted into Safe Boot Mode which is always slower than the regular boot.
Restart the system without holding down the shift key.
What do you mean by Ransom Ware? did you get a POPup claiming to be from the FBI? -
My macbook pro is running really slow after upgrade to Mavericks
my macbook pro is running really slow after upgrading to Mavericks....any ideas?
OS X Mavericks: If your Mac runs slowly
The above link is not very useful, so if it doesn't help read on.
There are many potential reasons that a Mac may be running slower than expected, but more information is required to begin troubleshooting, much more.
Back up your documents and everything else important to you before proceeding. It is premature to conclude your hard disk is failing, but the symptoms you describe may presage an impending disk failure, and you should have backups anyway.
To help determine the possible causes of this behaviour read the following. None of what follows is intended to fix anything, but it will provide the additional information required to advance troubleshooting:
Boot OS X Recovery by holding ⌘ and r (two fingers) while you start your Mac. At the Mac OS X Utilities screen, select Disk Utility. Select your startup volume (usually named "Macintosh HD") and click the Repair Disk button. Describe any errors it reports in red.
When it finishes restart your Mac and test again for operation. If it's still not behaving as you expect it should, please post the results of EtreCheck in accordance with the following instructions:
Apple Support Communities contributor etresoft wrote a very useful app to quickly gather certain system information that may help point to a cause of this problem. Go to his website, download and run EtreCheck:
http://www.etresoft.com/etrecheck
Etrecheck will be in your Downloads folder. Open it from there. You may see the following dialog box:
Click Open - etresoft contributes to this forum frequently and can be considered a trustworthy developer.
It will take a moment to run as it collects its data.
Copy and paste its output in a reply.
Do not be concerned about anything that says "Problem" or “failed” or anything else that may appear in red.
EtreCheck was designed to remove any personal information (such as your computer's name and serial numbers) but if you see anything that looks like an email address or any other personal information that should not be divulged to others, please delete or obscure that information when you post the reply.
When you are finished with EtreCheck, quit the program. It occupies very little space, and you can keep it or drag it to the Trash as you wish.
After completing the above please determine if the problems also occur in "Safe Mode":
Safe Mode or "Safe Boot" is a troubleshooting mode that bypasses all third party system extensions and loads only required system components. Read about it: Starting up in Safe Mode
You must disable FileVault before you can start your Mac in Safe Mode.
Starting your Mac in Safe Mode will take longer than usual, graphics will not render smoothly, audio is disabled on some Macs, and some programs (iTunes for example) may not work at all.
Merely starting your Mac in Safe Mode is not intended to resolve the problem, it's to observe its performance without certain additional components.
To end Safe Mode restart your Mac normally. Shutdown will take longer as well.
System performance problems for reasons that cannot be isolated to any other cause justify an SMC reset. Be sure to read the procedure carefully and follow all the steps exactly as written, even if they seem inapplicable or trivial. -
My MacBook Pro is running really slow - how can I fix it?
my MacBook Pro is running really slow - how can I fix it?
Things You Can Do To Resolve Slow Downs
If your computer seems to be running slower here are some things you can do:
Start with a visit to: OS X Maintenance - MacAttorney.
Boot into Safe Mode then repair your hard drive and permissions:
Repair the Hard Drive and Permissions Pre-Lion/Mountain Lion
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Repair the Hard Drive - Lion/Mountain Lion
Boot from your Lion Recovery HD. When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Restart your computer normally and see if this has helped any. Next do some maintenance:
Suggestions for OS X Maintenance
For situations Disk Utility cannot handle the best third-party utility is Disk Warrior; DW only fixes problems with the disk directory, but most disk problems are caused by directory corruption; Disk Warrior 4.x is now Intel Mac compatible.
OS X performs certain maintenance functions that are scheduled to occur on a daily, weekly, or monthly period. The maintenance scripts run in the early AM only if the computer is turned on 24/7 (no sleep.) If this isn't the case, then an excellent solution is to download and install a shareware utility such as Macaroni, JAW PseudoAnacron, or Anacron that will automate the maintenance activity regardless of whether the computer is turned off or asleep. Dependence upon third-party utilities to run the periodic maintenance scripts was significantly reduced since Tiger. These utilities have limited or no functionality with Snow Leopard or Lion and should not be installed.
OS X automatically defragments files less than 20 MBs in size, so unless you have a disk full of very large files there's little need for defragmenting the hard drive. As for virus protection there are few if any such animals affecting OS X. You can protect the computer easily using the freeware Open Source virus protection software ClamXAV. Personally I would avoid most commercial anti-virus software because of their potential for causing problems. For more about malware see Macintosh Virus Guide.
I would also recommend downloading a utility such as TinkerTool System, OnyX 2.4.3, or Cocktail 5.1.1 that you can use for periodic maintenance such as removing old log files and archives, clearing caches, etc.
For emergency repairs install the freeware utility Applejack. If you cannot start up in OS X, you may be able to start in single-user mode from which you can run Applejack to do a whole set of repair and maintenance routines from the command line. Note that AppleJack 1.5 is required for Leopard. AppleJack 1.6 is compatible with Snow Leopard. There is no confirmation that this version also works with Lion.
When you install any new system software or updates be sure to repair the hard drive and permissions beforehand.
Get an external Firewire drive at least equal in size to the internal hard drive and make (and maintain) a bootable clone/backup. You can make a bootable clone using the Restore option of Disk Utility. You can also make and maintain clones with good backup software. My personal recommendations are (order is not significant):
1. Carbon Copy Cloner
2. Data Backup
3. Deja Vu
4. SuperDuper!
5. SyncTwoFolders
6. Synk Pro
7. Synk Standard
8. Tri-Backup
Visit The XLab FAQs and read the FAQs on maintenance, optimization, virus protection, and backup and restore.
Additional suggestions will be found in Mac maintenance Quick Assist.
Referenced software can be found at CNet Downloads or MacUpdate.
Additional Hints
Be sure you have an adequate amount of RAM installed for the number of applications you run concurrently. Be sure you leave a minimum of 10% of the hard drive's capacity as free space.
Add more RAM. If your computer has less than 2 GBs of RAM and you are using OS X Leopard or later, then you can do with more RAM. Snow Leopard and Lion work much better with 4 GBs of RAM than their system minimums. The more concurrent applications you tend to use the more RAM you should have.
Always maintain at least 15 GBs or 10% of your hard drive's capacity as free space, whichever is greater. OS X is frequently accessing your hard drive, so providing adequate free space will keep things from slowing down.
Check for applications that may be hogging the CPU:
Open Activity Monitor in the Utilities folder. Select All Processes from the Processes dropdown menu. Click twice on the CPU% column header to display in descending order. If you find a process using a large amount of CPU time, then select the process and click on the Quit icon in the toolbar. Click on the Force Quit button to kill the process. See if that helps. Be sure to note the name of the runaway process so you can track down the cause of the problem.
Often this problem occurs because of a corrupted cache or preferences file or an attempt to write to a corrupted log file. -
My Macbook Pro is running really slow - anyone got any ideas?
chuanist wrote:
FWIW: I just looked over a friend's daughter's 2010 MacBook Pro unibody (2.66ghz) that was slow as molasses in Winter. She has been using it for her work at U.C. Berkeley for three months. After running Mac Janitor I repaired permissions with Disk Utility and there were thousands of files that needed to be re-set. After that it ran the way it should.
I was pretty surprised because when I repair permissions on my Mac Pro tower practically nothing gets changed.
http://support.apple.com/kb/TS1448 -
My Macbook Pro started running really slow
This week my Macbook Pro started running super slow, taking ages to open programs and giving me the color wheel alllll the time. I've never had problems like this before! I'm not running many applications or doing anything unusual but it's just running extra slow. Once or twice it has also totally gone to sleep while I was in the middle of using it, and I had to wake it back up. It has also been getting really hot and the battery life seems worse...! This is all new, I'm using my computer just as I always have but it suddenly has issues.
The only thing it has been doing for a while is sometimes the screen will go blue - this either corrects itself within a few seconds or if I close my Macbook and then reopen it, the screen is back to normal. This is very rare though and I don't know if it's related to the slowness problem.
What can I do to fix this??
Mac OS X 10.6.8
2 GHz Intel Core i7
4 GB 133 MHz DDR3
I just ran EtreCheck -
Hardware Information:
MacBook Pro (15-inch, Early 2011)
MacBook Pro - model: MacBookPro8,2
1 2 GHz Intel Core i7 CPU: 4 cores
4 GB RAM
Video Information:
AMD Radeon HD 6490M - VRAM: 256 MB
Intel HD Graphics 3000 - VRAM: 384 MB
System Software:
Mac OS X 10.6.8 (10K549) - Uptime: 1 day 3:59:13
Disk Information:
Hitachi HTS725050A9A362 disk0 : (465.76 GB)
(null) (disk0s1) <not mounted>: 200 MB
Macintosh HD (disk0s2) / [Startup]: 465.44 GB (235.1 GB free)
MATSHITADVD-R UJ-898
USB Information:
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. FaceTime HD Camera (Built-in)
Apple Computer, Inc. IR Receiver
FireWire Information:
Thunderbolt Information:
Apple, Inc. MacBook Pro
Kernel Extensions:
com.digidesign.iokit.DigiDal (8.0.3f1)
com.paceap.kext.pacesupport.snowleopard (5.7.2)
Startup Items:
DigidesignLoader: Path: /Library/StartupItems/DigidesignLoader
M-AudioFastTrack: Path: /Library/StartupItems/M-AudioFastTrack
PACESupport: Path: /Library/StartupItems/PACESupport
Problem System Launch Daemons:
[System] org.samba.winbindd.plist 3rd-Party support link
Launch Daemons:
[System] com.adobe.fpsaud.plist 3rd-Party support link
[System] com.google.keystone.daemon.plist 3rd-Party support link
[System] com.microsoft.office.licensing.helper.plist 3rd-Party support link
[System] org.eyebeam.SelfControl.plist 3rd-Party support link
[System] PACESupport.plist 3rd-Party support link
Launch Agents:
[System] com.google.keystone.agent.plist 3rd-Party support link
[System] com.hp.help.tocgenerator.plist 3rd-Party support link
[System] com.m-audio.mobilepremkii.helper.plist 3rd-Party support link
User Launch Agents:
[not loaded] com.apple.CSConfigDotMacCert-[...]@me.com-SharedServices.Agent.plist
[not loaded] com.facebook.videochat.[redacted].plist 3rd-Party support link
[not loaded] com.spotify.webhelper.plist 3rd-Party support link
User Login Items:
Flux
iTunesHelper
RescueTime
Internet Plug-ins:
o1dbrowserplugin: Version: 5.2.4.18058 3rd-Party support link
Unity Web Player: Version: UnityPlayer version 3.5.2f2 - SDK 10.6 3rd-Party support link
RealPlayer Plugin: Version: Unknown
Silverlight: Version: 5.1.20913.0 - SDK 10.6 3rd-Party support link
FlashPlayer-10.6: Version: 12.0.0.77 - SDK 10.6 3rd-Party support link
QuickTime Plugin: Version: 7.6.6
Flash Player: Version: 12.0.0.77 - SDK 10.6 3rd-Party support link
googletalkbrowserplugin: Version: 5.2.4.18058 3rd-Party support link
SharePointBrowserPlugin: Version: 14.3.9 - SDK 10.6 3rd-Party support link
AdobePDFViewer: Version: 10.1.1 3rd-Party support link
iPhotoPhotocast: Version: 7.0 - SDK 10.7
JavaAppletPlugin: Version: 13.9.8 - SDK 10.6 Outdated! Update
iTunes Plug-ins:
Quartz Composer Visualizer: Version: 1.2
3rd Party Preference Panes:
Flash Player 3rd-Party support link
Growl 3rd-Party support link
M-AudioFastTrack 3rd-Party support link
M-Audio MobilePre 3rd-Party support link
Old Applications:
None
Time Machine:
Time Machine information requires OS X 10.7 "Lion" or later.
Top Processes by CPU:
7% firefox
3% WindowServer
3% EtreCheck
2% hidd
0% coreservicesd
Top Processes by Memory:
397 MB firefox
106 MB mds
82 MB WindowServer
82 MB Mail
49 MB quicklookd
Virtual Memory Information:
1.04 GB Free RAM
1.04 GB Active RAM
1.03 GB Inactive RAM
907 MB Wired RAM
467 MB Page-ins
0 B Page-outsThe startup drive is failing, or there is some other internal hardware fault. The "etrecheck" output is irrelevant.
Back up all data on the drive immediately if you don't already have a current backup. There are ways to back up a computer that isn't fully functional — ask if you need guidance.
Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.
If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
Keeping your confidential data secure during hardware repair
Apple also recommends that you deauthorize a device in the iTunes Store before having it serviced.
*An SSD doesn't need to be zeroed. -
My Macbook pro suddenly running very slow
I have a 13" mid 2012 Macbook pro running OS X Mavericks v 10.9.4. About two weeks ago it suddenly became very slow and unresponsive. Startup and shut down takes much longer than usual, file transfers are slow and apps are taking forever to launch. The rainbow wheel would show up almost anytime and trivial tasks like opening a new tab in browser or opening finder. More recently, a new problem has also cropped up: my mac is not going to sleep on closing the lid.
Over last two weeks I have tried the following:
- Repair disk and disk permissions.
- Reset SMC
- Reset PRAM
- Start in safe mode.
- Clean install of OS X (after erasing the hard drive).
but none of this has helped. I also ran Apple Hardware Test but got nothing. I fear my hard drive may be failing. Is there anything else I can try before I have to take it to the apple store. Any help would be sppreciated. Thanks.
Here is some information on my macbook:
MacBook Pro 13-inch Mid 2012
Processor 2.5 GHz Intel Core i5
Memory 4 GB 1600 MHz DDR3
Graphics Intel HD Graphics 4000
Software OS X 10.9.4 (13E28)1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can read it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB com.apple.AirPortBaseStationAgent 464843899 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { print "'${p[41]}'";if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$|'${p[41]}'/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { print "'${p[41]}'.plist\t'${p[42]}'";if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\\([0-9]+\\)\\(.+\\)/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p);if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|(Bo|PO).+ sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" ' BEGIN{FS="= "} /Path/{print $2} ' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test osascript\ -e );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'|tr , \\\n" 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'bad |Beac|caug|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA\(|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:| VALI|xpma' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Co{mpon,reM},Ex,Inter,iTu*/*P,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -path \\*s/Resources -prune -o -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t /S*/L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 35 49 61 51;D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D23 14 1 62 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 37 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 26 48 49 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
Why is my MacBook Pro suddenly running as slow as syrup?
Hello,
I read some of the replies to the other posts about MacBook pro suddenly running slowly, and I am about to try a repair and do a few other things, but I was wondering if anyone could tell me if my etrecheck.com details offer a hint as to why it's running so slowly. I have pasted them below.
A few things to note:
1. I have since turned off Time Machine backup on this computer, and I am just about to uninstall the app BackTrack and all the LogMeIn crap.
2. I repair permissions on this machine at least twice a month, sometimes more often.
2. For the past month or so, my computer has been making this desperate sounding single beep after I log into my user account and after all the startup stuff is done. I read somewhere that it means my computer is about to die, but figured I would throw it out there.
I appreciate any insight.
Thanks,
Jen
Hardware Information:
MacBook Pro (13-inch, Early 2011)
MacBook Pro - model: MacBookPro8,1
1 2.3 GHz Intel Core i5 CPU: 2 cores
4 GB RAM
Video Information:
Intel HD Graphics 3000 - VRAM: 384 MB
System Software:
OS X 10.9.2 (13C64) - Uptime: 0 days 17:10:27
Disk Information:
ST9320325ASG disk0 : (320.07 GB)
EFI (disk0s1) <not mounted>: 209.7 MB
Macintosh HD (disk0s2) / [Startup]: 319.21 GB (168.57 GB free)
Recovery HD (disk0s3) <not mounted>: 650 MB
HL-DT-ST DVDRW GS31N
USB Information:
Apple Computer, Inc. IR Receiver
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
FireWire Information:
Thunderbolt Information:
Apple Inc. thunderbolt_bus
Kernel Extensions:
com.logmein.driver.LogMeInSoundDriver (1.0.3 - SDK 10.5)
Launch Daemons:
[System] com.adobe.fpsaud.plist 3rd-Party support link
[System] com.google.keystone.daemon.plist 3rd-Party support link
[System] com.logmein.logmeinblanker.plist 3rd-Party support link
[System] com.logmein.logmeinserver.plist 3rd-Party support link
[System] com.logmein.raupdate.plist 3rd-Party support link
[System] com.microsoft.office.licensing.helper.plist 3rd-Party support link
[System] com.oracle.java.Helper-Tool.plist 3rd-Party support link
Launch Agents:
[System] com.logmein.LMILaunchAgentFixer.plist 3rd-Party support link
[System] com.logmein.logmeingui.plist 3rd-Party support link
[System] com.logmein.logmeinguiagent.plist 3rd-Party support link
[System] com.logmein.logmeinguiagentatlogin.plist 3rd-Party support link
[System] com.oracle.java.Java-Updater.plist 3rd-Party support link
User Launch Agents:
[not loaded] com.adobe.ARM.[...].plist 3rd-Party support link
[not loaded] com.nds.pcshow.plist 3rd-Party support link
[not loaded] com.nds.pcshow.uninstall.plist 3rd-Party support link
User Login Items:
BackTrackBA
AdobeResourceSynchronizer
Internet Plug-ins:
Default Browser: Version: 537 - SDK 10.9
AdobePDFViewerNPAPI: Version: 11.0.06 - SDK 10.6 3rd-Party support link
FlashPlayer-10.6: Version: 12.0.0.77 - SDK 10.6 3rd-Party support link
LogMeIn: Version: 1.0.935 - SDK 10.7 3rd-Party support link
Silverlight: Version: 5.1.20913.0 - SDK 10.6 3rd-Party support link
Flash Player: Version: 12.0.0.77 - SDK 10.6 Outdated! Update
LogMeInSafari32: Version: 1.0.935 - SDK 10.7 3rd-Party support link
googletalkbrowserplugin: Version: 3.8.1.9672 3rd-Party support link
npgtpo3dautoplugin: Version: 0.1.44.21 - SDK 10.5 3rd-Party support link
AdobePDFViewer: Version: 11.0.06 - SDK 10.6 3rd-Party support link
QuickTime Plugin: Version: 7.7.3
SharePointBrowserPlugin: Version: 14.3.9 - SDK 10.6 3rd-Party support link
WidevineMediaOptimizer: Version: (null) 3rd-Party support link
JavaAppletPlugin: Version: Java 7 Update 51 3rd-Party support link
Audio Plug-ins:
BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
AirPlay: Version: 2.0 - SDK 10.9
AppleAVBAudio: Version: 203.2 - SDK 10.9
iSightAudio: Version: 7.7.3 - SDK 10.9
iTunes Plug-ins:
Quartz Composer Visualizer: Version: 1.4 - SDK 10.9
User Internet Plug-ins:
Picasa: Version: 1.0 3rd-Party support link
3rd Party Preference Panes:
Flash Player 3rd-Party support link
Java 3rd-Party support link
Old Applications:
/Library/Application Support/Microsoft/MERP2.0
Microsoft Error Reporting: Version: 2.2.9 - SDK 10.4 3rd-Party support link
Microsoft Ship Asserts: Version: 1.1.4 - SDK 10.4 3rd-Party support link
Solver: Version: 1.0 - SDK 10.5 3rd-Party support link
/Applications/Microsoft Office 2011/Office/Add-Ins/Solver.app
SLLauncher: Version: 1.0 - SDK 10.5 3rd-Party support link
/Library/Application Support/Microsoft/Silverlight/OutOfBrowser/SLLauncher.app
/Applications/Microsoft Office 2011/Office
Open XML for Excel: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Office Setup Assistant: Version: 14.3.3 - SDK 10.5 3rd-Party support link
Microsoft Alerts Daemon: Version: 14.3.9 - SDK 10.5 3rd-Party support link
SyncServicesAgent: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Database Daemon: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Graph: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Database Utility: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Office Reminders: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Upload Center: Version: 14.3.9 - SDK 10.5 3rd-Party support link
My Day: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Chart Converter: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Clip Gallery: Version: 14.3.9 - SDK 10.5 3rd-Party support link
/Applications/Microsoft Office 2011
Microsoft PowerPoint: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Excel: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Outlook: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Word: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Document Connection: Version: 14.3.9 - SDK 10.5 3rd-Party support link
Microsoft Language Register: Version: 14.3.9 - SDK 10.5 3rd-Party support link
/Applications/Microsoft Office 2011/Additional Tools/Microsoft Language Register/Microsoft Language Register.app
Aimersoft Helper Compact: Version: 2.2.5.6 - SDK 10.5 3rd-Party support link
/Users/[redacted]/Library/Application Support/Helper/Aimersoft Helper Compact.app
Microsoft AutoUpdate: Version: 2.3.6 - SDK 10.4 3rd-Party support link
/Library/Application Support/Microsoft/MAU2.0/Microsoft AutoUpdate.app
Aimersoft DVD Ripper: Version: 2.6.2 - SDK 10.5 3rd-Party support link
Spotify: Version: 0.8.5.1333.g822e0de8 - SDK 10.5 3rd-Party support link
Time Machine:
Skip System Files: NO
Mobile backups: ON
Auto backup: YES
Volumes being backed up:
Macintosh HD: Disk size: 297.29 GB Disk used: 140.30 GB
Destinations:
kathmere [Network] (Last used)
Total size: 2
Total number of backups: 43
Oldest backup: 2014-02-28 23:49:13 +0000
Last backup: 2014-04-12 04:35:47 +0000
Size of backup disk: Excellent
Backup size 2 > (Disk size 297.29 GB X 3)
Time Machine details may not be accurate.
All volumes being backed up may not be listed.
Top Processes by CPU:
4% WindowServer
2% EtreCheck
1% hidd
1% systemstatsd
0% configd
Top Processes by Memory:
266 MB firefox
143 MB com.apple.IconServicesAgent
127 MB softwareupdated
102 MB mds_stores
74 MB mds
Virtual Memory Information:
1.22 GB Free RAM
1.44 GB Active RAM
332 MB Inactive RAM
1.02 GB Wired RAM
795 MB Page-ins
288 KB Page-outsOS X Mavericks: If your Mac runs slowly?
Startup in Safe Mode
http://support.apple.com/kb/PH14204
Repair Disk
Steps 1 through 7
http://support.apple.com/kb/PH5836
Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own". -
My MacBook Pro suddenly started running slow
Hi,
My MacBook Pro started running extremely slow a couple of days ago. I tried to search for help and found this forum where people had the same problem. I see that people are advised to check with etrecheck software and post it here to have further instructions. So I did mine and below are my results. I have opened the back of my laptop, cleaned up everything including the dirty fan and reseated the hard drive (which I had problem with loose cable in the past). It seems to fix the slow problem at the moment but the problem keeps appearing once in a while. So I hope someone could help me out. Thanks a lot in advance.
Hardware Information:
MacBook Pro (13-inch, Mid 2009)
MacBook Pro - model: MacBookPro5,5
1 2.53 GHz Intel Core 2 Duo CPU: 2 cores
4 GB RAM
Video Information:
NVIDIA GeForce 9400M - VRAM: 256 MB
System Software:
Mac OS X 10.6.8 (10K549) - Uptime: 0 days 0:10:41
Disk Information:
Hitachi HTS545025B9SA02 disk0 : (232.89 GB)
(null) (disk0s1) <not mounted>: 200 MB
Macintosh HD (disk0s2) / [Startup]: 232.57 GB (67.16 GB free)
HL-DT-ST DVDRW GS23N
USB Information:
Apple Inc. Built-in iSight
Apple Internal Memory Card Reader
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
Thunderbolt Information:
Kernel Extensions:
[not loaded] com.Immersion.driver.ImmersionForceFeedback (1.0.7) Support
[not loaded] com.acard.driver.ACard6280ATA (1.0.5) Support
[not loaded] com.acard.driver.ACard62xxM (2.0.6) Support
[not loaded] com.acard.driver.ACard67162 (2.0.3) Support
[not loaded] com.acard.driver.ACard671xSCSI (2.0.1) Support
[not loaded] com.acard.driver.ACard6885M (2.0.6) Support
[not loaded] com.acard.driver.ACard68xxM (2.0.5) Support
[kext loaded] com.cisco.nke.ipsec (2.0.1) Support
[not loaded] com.logitech.driver.LogitechForceFeedback (1.0.3) Support
Startup Items:
CiscoVPN: Path: /System/Library/StartupItems/CiscoVPN
MATLABLmgr: Path: /Library/StartupItems/MATLABLmgr
Problem System Launch Daemons:
[not loaded] org.samba.winbindd.plist Support
Problem System Launch Agents:
[failed] com.apple.Kerberos.renew.plist
Launch Daemons:
[loaded] com.adobe.fpsaud.plist Support
[loaded] com.bombich.ccc.plist Support
[loaded] com.google.keystone.daemon.plist Support
Launch Agents:
[loaded] com.adobe.CS4ServiceManager.plist Support
[loaded] com.google.keystone.agent.plist Support
User Launch Agents:
[loaded] com.adobe.ARM.[...].plist Support
[running] com.spotify.webhelper.plist Support
[failed] com.zeobit.MacKeeper.Helper Support
User Login Items:
MacShield
iTunesHelper
QuickTime Player 7
Mail
Dropbox
ExpanderDaemon
Internet Plug-ins:
Flip4Mac WMV Plugin: Version: 2.3.6.5 Support
FlashPlayer-10.6: Version: 13.0.0.206 - SDK 10.6 Support
QuickTime Plugin: Version: 7.6.6
Flash Player: Version: 13.0.0.206 - SDK 10.6 Support
AdobePDFViewer: Version: 9.5.5 Support
DivXBrowserPlugin: Version: 2.0 Support
o1dbrowserplugin: Version: 5.3.1.18536 Support
Google Earth Web Plug-in: Version: 7.1 Support
googletalkbrowserplugin: Version: 5.3.1.18536 Support
Silverlight: Version: 5.1.10411.0 - SDK 10.6 Support
JavaAppletPlugin: Version: 13.9.8 - SDK 10.6 Check version
iTunes Plug-ins:
Quartz Composer Visualizer: Version: 1.2
User Internet Plug-ins:
WebEx64: Version: 1.0 - SDK 10.5 Support
WebEx: Version: 1.0 Support
3rd Party Preference Panes:
DivX Support
Flash Player Support
Flip4Mac WMV Support
TeXDistPrefPane Support
Top Processes by CPU:
65% mdworker
1% hidd
1% WindowServer
1% Safari
0% fontd
Top Processes by Memory:
184 MB Safari
111 MB WebProcess
82 MB Dropbox
66 MB Mail
41 MB PubSubAgent
Virtual Memory Information:
2.40 GB Free RAM
776 MB Active RAM
219 MB Inactive RAM
391 MB Wired RAM
177 MB Page-ins
0 B Page-outsHi dippypants and dominic23,
Thanks for your help. I followed dippypants' advice and checked the Activity Monitor. Most of the processess that occupy my CPU and memory are Safari and Safari Web Content. Sometimes when these go down to low, I still have the same problem with computer running super slow.
I then followed dominic23's advice to look for MacKeeper not only in Applications but my whole laptop but I could not find it any where. Yet it still shows when I do the etrecheck. Do you guys think I might have some malware problem?
Thanks! Any help is much appreciated.
Below is the latest check using etrecheck software.
Hardware Information:
MacBook Pro (13-inch, Mid 2009)
MacBook Pro - model: MacBookPro5,5
1 2.53 GHz Intel Core 2 Duo CPU: 2 cores
4 GB RAM
Video Information:
NVIDIA GeForce 9400M - VRAM: 256 MB
System Software:
Mac OS X 10.6.8 (10K549) - Uptime: 0 days 0:12:7
Disk Information:
Hitachi HTS545025B9SA02 disk0 : (232.89 GB)
(null) (disk0s1) <not mounted>: 200 MB
Macintosh HD (disk0s2) / [Startup]: 232.57 GB (67.07 GB free)
HL-DT-ST DVDRW GS23N
USB Information:
Apple Internal Memory Card Reader
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Built-in iSight
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Thunderbolt Information:
Kernel Extensions:
[not loaded] com.Immersion.driver.ImmersionForceFeedback (1.0.7) Support
[not loaded] com.acard.driver.ACard6280ATA (1.0.5) Support
[not loaded] com.acard.driver.ACard62xxM (2.0.6) Support
[not loaded] com.acard.driver.ACard67162 (2.0.3) Support
[not loaded] com.acard.driver.ACard671xSCSI (2.0.1) Support
[not loaded] com.acard.driver.ACard6885M (2.0.6) Support
[not loaded] com.acard.driver.ACard68xxM (2.0.5) Support
[kext loaded] com.cisco.nke.ipsec (2.0.1) Support
[not loaded] com.logitech.driver.LogitechForceFeedback (1.0.3) Support
Startup Items:
CiscoVPN: Path: /System/Library/StartupItems/CiscoVPN
MATLABLmgr: Path: /Library/StartupItems/MATLABLmgr
Problem System Launch Daemons:
[not loaded] org.samba.winbindd.plist Support
Problem System Launch Agents:
[failed] com.apple.Kerberos.renew.plist
Launch Daemons:
[loaded] com.adobe.fpsaud.plist Support
[loaded] com.bombich.ccc.plist Support
[loaded] com.google.keystone.daemon.plist Support
Launch Agents:
[loaded] com.adobe.CS4ServiceManager.plist Support
[loaded] com.google.keystone.agent.plist Support
User Launch Agents:
[loaded] com.adobe.ARM.[...].plist Support
[running] com.spotify.webhelper.plist Support
[failed] com.zeobit.MacKeeper.Helper Support
User Login Items:
MacShield
iTunesHelper
QuickTime Player 7
Mail
Dropbox
ExpanderDaemon
Internet Plug-ins:
Flip4Mac WMV Plugin: Version: 2.3.6.5 Support
FlashPlayer-10.6: Version: 13.0.0.206 - SDK 10.6 Support
QuickTime Plugin: Version: 7.6.6
Flash Player: Version: 13.0.0.206 - SDK 10.6 Support
AdobePDFViewer: Version: 9.5.5 Support
DivXBrowserPlugin: Version: 2.0 Support
o1dbrowserplugin: Version: 5.3.1.18536 Support
Google Earth Web Plug-in: Version: 7.1 Support
googletalkbrowserplugin: Version: 5.3.1.18536 Support
Silverlight: Version: 5.1.10411.0 - SDK 10.6 Support
JavaAppletPlugin: Version: 13.9.8 - SDK 10.6 Check version
iTunes Plug-ins:
Quartz Composer Visualizer: Version: 1.2
User Internet Plug-ins:
WebEx64: Version: 1.0 - SDK 10.5 Support
WebEx: Version: 1.0 Support
3rd Party Preference Panes:
DivX Support
Flash Player Support
Flip4Mac WMV Support
TeXDistPrefPane Support
Top Processes by CPU:
44% Finder
22% Mail
2% WindowServer
2% hidd
0% Activity Monitor
Top Processes by Memory:
246 MB Safari
147 MB Microsoft Word
115 MB WebProcess
98 MB Mail
82 MB Dropbox
Virtual Memory Information:
2.26 GB Free RAM
999 MB Active RAM
124 MB Inactive RAM
403 MB Wired RAM
238 MB Page-ins
0 B Page-outs -
Why does my MacBook Pro suddenly turn really really slow and make a really loud fan noise?
Whenever I turn on my MacBook is runs perfectly fine for 2 minutes but then it turns really slow (to the point that it takes ages to move the mouse cursor and to type) and make a really loud fan noise. What should I do to fix this?
Welcome to Apple Support Communities
There's a process that is taking up the RAM and CPU. Open Activity Monitor (in /Applications/Utilities), and select "All Processes" above "Show" in the toolbar. Then, order processes by CPU, and tell me which processes you see that are consuming more CPU -
MacBook Pro suddenly running very slow
I own a MacBook Pro 13-inch (late 2012).
I have always taken very good care of my Mac, and up until 2 weeks ago, it was running at a beautiful speed and performing really well.
Suddenly, one morning when I turned it on, it took ages to boot up and then performed extremely slow. And it has been that way ever since.
I have tried cleaning the hard drive and making a clean install of Yosemite but with no improvement. It has been really frustrating, especially now that I can't even book an Apple Genius appointment to get it checked. I have run the EtreCheck and copied the results below. Any help will be much appreciated!
Problem description:
System running much slower than expected.
EtreCheck version: 2.1.8 (121)
Report generated 21 February 2015 12:37:32 GMT
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Hardware Information: ℹ️
MacBook Pro (13-inch, Mid 2012) (Technical Specifications)
MacBook Pro - model: MacBookPro9,2
1 2.9 GHz Intel Core i7 CPU: 2-core
8 GB RAM Upgradeable
BANK 0/DIMM0
4 GB DDR3 1600 MHz ok
BANK 1/DIMM0
4 GB DDR3 1600 MHz ok
Bluetooth: Good - Handoff/Airdrop2 supported
Wireless: en1: 802.11 a/b/g/n
Battery Health: Normal - Cycle count 909
Video Information: ℹ️
Intel HD Graphics 4000
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.2 (14C109) - Time since boot: 0:8:56
Disk Information: ℹ️
TOSHIBA MK7559GSXF disk0 : (750.16 GB)
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
Macintosh HD (disk1) / : 748.93 GB (707.12 GB free)
Encrypted AES-XTS Unlocked
Core Storage: disk0s2 749.30 GB Online
MATSHITADVD-R UJ-8A8
USB Information: ℹ️
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Computer, Inc. IR Receiver
Apple Inc. FaceTime HD Camera (Built-in)
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Launch Agents: ℹ️
[loaded] com.oracle.java.Java-Updater.plist [Click for support]
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Click for support]
[loaded] com.microsoft.office.licensing.helper.plist [Click for support]
[loaded] com.oracle.java.Helper-Tool.plist [Click for support]
User Launch Agents: ℹ️
[loaded] com.google.keystone.agent.plist [Click for support]
User Login Items: ℹ️
Dropbox Application (/Applications/Dropbox.app)
Internet Plug-ins: ℹ️
FlashPlayer-10.6: Version: 16.0.0.305 - SDK 10.6 [Click for support]
QuickTime Plugin: Version: 7.7.3
Flash Player: Version: 16.0.0.305 - SDK 10.6 [Click for support]
Default Browser: Version: 600 - SDK 10.10
SharePointBrowserPlugin: Version: 14.4.7 - SDK 10.6 [Click for support]
Unity Web Player: Version: UnityPlayer version 4.6.2f1 - SDK 10.6 [Click for support]
JavaAppletPlugin: Version: Java 8 Update 31 Check version
Safari Extensions: ℹ️
AdBlock
Save to Pocket
3rd Party Preference Panes: ℹ️
Flash Player [Click for support]
Java [Click for support]
Time Machine: ℹ️
Auto backup: YES
Volumes being backed up:
Macintosh HD: Disk size: 748.93 GB Disk used: 41.81 GB
Destinations:
Install OS X Yosemite [Local]
Total size: 999.86 GB
Total number of backups: 0
Oldest backup: -
Last backup: -
Size of backup disk: Adequate
Backup size 999.86 GB > (Disk used 41.81 GB X 3)
Top Processes by CPU: ℹ️
4% WindowServer
0% com.apple.WebKit.Networking
0% SystemUIServer
0% SpotlightNetHelper
Top Processes by Memory: ℹ️
223 MB Safari
103 MB com.apple.WebKit.WebContent
77 MB Dropbox
69 MB WindowServer
52 MB CalendarAgent
Virtual Memory Information: ℹ️
5.07 GB Free RAM
2.27 GB Active RAM
422 MB Inactive RAM
821 MB Wired RAM
990 MB Page-ins
0 B Page-outs
Diagnostics Information: ℹ️
Feb 21, 2015, 12:18:33 PM Self test - passedFurthermore, I tried testing my RAM using Memtest twice, and it seemed to have passed all tests.
I also used Disk Utility to verify my hard drive and that seemed to have passed all tests too.
Anything else I can test?
Maybe you are looking for
-
How can I reinstall my mail accounts and get all my mails back?
My internal HD died a few days ago . Fortunately I did a Time Machine backup a couple of hours before it happened . Now my MacBook Pro is back from the repair center, with a brand new HD and Mac OS 10.6.8 installed (the system I had) . But how can I
-
I have had itunes library to go away and itunes create a new one. how do I get my old one back?
I have had itunes library to go away and itunes create a new one. how do I get my old one back?
-
How to create adf columns at runtime
Hello I want to crete a component which will display results of arbitrary sql command. for that purpose I created 'declared component' with custom component class which obtains SQL query from passed attibute and executes it. so in my component I have
-
Configuration on domain name inside Business Catalyst
I created a web site in Muse and using Business Catalyst to upload this site. I purchased the url (domain name) from godaddy.com. Currently, the domain is parked at godaddy.com and I need a DNS to re-route the site back to Adobe Business Catalyst.. h
-
Hi, There is one messageTextInput in which date is being entered. I want to compare this date with system date and according to go in next page or throw an error. But when I do OAMessageDateFieldBean endDate = (OAMessageDateFieldBean)oawebbean.findCh