NaN output - Urgent

I am using DAQc 9172 Chassis and obtaining temperature using NI 9217 and Pressure from NI 9205. I get the output properly from the vi file. I am using Lab view 8.2.1 version. But when I build the executable (Application.exe) and use it for execution at the standalone PC which already has been installed with only (LV version 8.5)Ni DAQmx and runtime Engine , I get the pressure and temperature values as NaN.
However the application.exe file runs fine in the main PC which has been installed with Labview 8.2.1.
Can anyone help me in fixing this problem?
Solved!
Go to Solution.

If your target computer have LV8.5 You may do some debugging on this computer. Check with MAX to sort out naming problems with the daq unit
Message Edited by t06afre on 02-09-2009 03:15 PM
Besides which, my opinion is that Express VIs Carthage must be destroyed deleted
(Sorry no Labview "brag list" so far)

Similar Messages

Why does SCXI 1325 give a NaN output at all channels?

Till yesterday SCXI 1125 was working fine. But today the values that I am getting from all its channels is "NaN". No error is given.
When I tried running the Test Panels thru NI-MAX, SCXI 1125 still gave a NaN output, while 6040E, 6251 and SCXI 1142 did not.
Can someone tell me what is the problem and how it can be rectified?
Setup :
PXI chasis consisting of PXI 6040E and 6251
SCXI 1000 chasis consisting SCXI 1142 and 1125
Connection to SCXI 1000 chassis is thru PXI 6040E
PXI 6040E connected to SCXI 1142 (accessory SCXI 1304)
PXI 6251 connected to SCXI 1125 (accessory SCXI 1313)
Data collection thru Parallel mode
Thanks
Jag

Thanks Kodee for your reply.
Well this is what I have done so far :
a) Removed all the SCXI modules and reconnected them. Checked the wiring.
But still get the same result "NaN" for SCXI 1125
b) Reinstalled DaQmx drivers
Still the same NaN result for SCXI 1125
Also I have now realised that when I try to measure an analog signal thru the module SCXI 1142, I get some varying signal initially followed by a steady 5V signal.
I am not sure whether this fault was present yesterday when I first came across the NaN problem with SCXI 1125.
So right now, SCXI 1142 gives a steady 5V output while SCXI 1125 gives a NaN output.
Could you suggest what I should do next?
Also in your reply you had asked me to check whether any printer drivers are interuppting NI drivers. How can I check that out?
Thanks
Jag

Extra Page coming in the PDF output -- Urgent

Hi All,
I have created an AR Invoice Print report (pre-printed).
size of the stationary is half of A4.
In a single A4 page two invocies will be accommodated.
Here i have not used page break concept. I have adjusted the template with spaces.
But when are invoices are given in a range lets say 1 to 10.
The PDF output should have 5 pages accommodating 2 invoice in each page (this is working perfectly), but with this an extra black page is also getting generated. (The PDF is having 6 pages).
If the range is given between 1 to 9 the extra blank page will not get generated.
Is there any way to solve this issue???
It little bit urgent.. :)
Regards,
Jana

Jana,
http://blogs.oracle.com/xmlpublisher/2007/03/
Check on the "Anatomy of a Template I & II"... should work on your case. Also, make sure extra carriage returns and unnecessary spaces between tables are removed. If you use fillers, be sure to have the same height attribute as the field being filled.
regards,
Rownald

Embedding Flash swf in Google Site displays NaN output but works in Debug mode

Hello,
I am loading a text file with three variables into a flash file (CS5). The flash file then calculates and prints the three values based on some calculations. I am storing the text file as an attachment on the google page in which I am embedding the swf file. What's weird is that the flash file plays correctly in debugging mode (i.e., prints the 3 variables correctly), but as soon as I upload the swf to the Google site page (as an attachment in the same location as the text file), the flash file outputs NaN. I am stuck as to why the file works in debug mode in Flash, but not when it's uploaded to the google site page. I have tried storing the text file on SharePoint and referencing it from there, but I get the same results when viewing the swf on the Google site page.
Is it because the google site page is using SSL?
I am fairly new to flash, so any help would be appreciated.
Thanks!
Lori
Variables.txt stores this: "current=6950&goal=7175&low=6950"
Here is the code in my flash file:
_global.getPercent = "";
myvars = new LoadVars();
myvars.load("variables.txt");
myvars.onLoad = function(success){
          l = Number(myvars.low);
          c = Number(myvars.current);
          g = Number(myvars.goal);
          getPercent = (c-l)/(g-l);
          if (getPercent > 0) {
                    colorshow._height = (getPercent*colorshow._height);
          } else {
                    colorshow._height = 0;

I have this in front of the trace:
myvars.onLoad = function(success){
When I put in the full URL to the attachment on the Google page (i.e., something similar to "myvars.load("https://sites.google.com/a/..../home/department-sites/sales/variables.txt,");" - instead of just "myvars.load("variables.txt");", it doesn't work. So right now its set to just "variables.txt" and the swf file is in the same root location as the variables.txt file on the Google page. I also have a copy of the variables.txt file in the same local directly in which I am running the flash file for testing. So I think when I run it in debug mode, its referencing the variables.txt file in the local directory, rather than the one stored as an attachment on the Google page.
That's what seems so weird...it runs locally in debug mode...but not when I embed it on the Google page. I can also get it to work if I explicity define the variables in the flash file, rather than rely on the external text file. That's the only time I can get it to work on the Google page.
Thank you for your help!

How to find a report output - URGENT

Hi all,
We have an ABAP program and its basically a report, how can I see the output of the report ie the list.
Please let me know
thanks
Sabrina.

thanks Priyank for your reply.
Well we have an ABAP program in BW that outputs a flat file of data. It is basically a report, it runs every morning and I need to find out the output of the report. In SM37 when I select the job and click the button SPOOL, I get the following message that I don't have authorization to view the list.
No authorization to select from spool request 24,323 in system CBP
and then it says list contains no data.
What should I do? Please let me know.
thanks
Sabrina.

Display empty fields in between the output, urgent

hi
i need to display some empty fields in the output txt file, in between teh normal database fields i am displaying
for eg if first field is f1 (1-10)
second is f2 (11-35)
third field is empty i need todisplay as (12-45)
and again f4 as (13-60) so on
such there are multiple fields in between dattabase field which just needs to be displayed as empty only and all fields should be seperated by space as showni above eg
regards
arora

closed got solution

Graph for a query output---urgent

Hi,
My requirment is to have a report which shows top 3 cubes based on number of records for each week.I also have to plot this in a graph
the graph should be as follows
Y axis : No of records
X axis : Cubes which are grouped based on week.ie Suppose top 3 cubes for
Week 1 is c11,c12,c13
and
Week 2 is c21,c22,c23
then graph should show
no of records on Yaxis
and
C11,c12,c13 as one series and
c21,c22,c23 as second series.
I tries this but Xaxis is showing either C11,c12,c13 or
c21,c22,c23
since we cannot give values to X axias on a series basis.
Please suggest a way to solve it or a different approch for th above requirment
Please help this urgent....

Hi,
I think you need to develop multiprovider over 3 cubes. Build a single query on this multiprovider and then plot the graph.
Other way you can try Excel Macro to plot the graph.
Hope it helps.
Regards,
Aditya

ME2N -Customized output -Urgent!!!

I have customized ME2N transaction, my output is ALV format , Here I just changed to logic of 2 performs where I can add the my own flds into the output list.
for the GUI status which is not working like PO changes,scheduled...buttons (also there in the standard transaction).
Please help me

Hi,
You can create your own local strcutureby inlcuding this strucutre as follows.
TYPES: begin of new_struct.
INCLUDE STRUCUTRE MEREP_OUTTAB_PURCHDOC.
TYPES: new_filed type <give your type here>,
end of new_Struct.
then create table type and work area for the new type.
DATA: itab type table of new_Struct,
wa_area like line of itab.
now copy data as followows.
LOOP at original_ta into origianl_workarea.
move-corresponding original_workarea to wa_area.
wa_area-new_filed = <assign your value using some code READ TABLE etc>.
append wa_area to itab.
endloop.
then create list using ITAB instead of original table.
Regards,
Sesh

XML Output(Urgent)

Hi,
I want to build XML file like this(below one) in .NET.I am
getting one sub element i.e Year .But I am not getting Item and its
attributes within the Year element.Its very Urgent.I am using XML
serializer for this.
<energyrecap>
<year id="2006">
<item type="usage" value="4.666" month="Jan" />
<item type="usage" value="4.666" month="Feb" />
<item type="usage" value="4.666" month="Mar" />
<item type="usage" value="4.666" month="Apr" />
</year>
<year id="2007">
<item type="usage" value="5.666" month="Sep" />
<item type="usage" value="4.666" month="Oct" />
<item type="usage" value="3.666" month="Nov" />
<item type="usage" value="5.666" month="Dec" />
</year>
</energyrecap>

You'll have a lot more luck with this question on dot.net
forum than here.
I use dot.net to return xml, but I have never used
XMLSerializer.
Tracy

BA00 Output Urgent

Hi all,
I created a new payment terms but the invoice output shows
the one thats in the order i.e. the correct one.
but the order output shows the diffrent payment terms the one that is not in the order or the customer master.
all partner functions are same.
Rgds

hi,
check your layout program with help of your abaper. It seems that part of text is either hardcoded or you would then need to check the print program whcih is fetching the values from VBKD table.
Your abaper can simply debug the output program and can fix it.
regards
sadhu kishore

PO output -Urgent

Experts,
I am facing a strange problem. This is related E-mail output
Email id is maintained in vendor master.
PO has been created without Message Output (vendor or Partner not selected in messages)
So it is not supposed to send email to any vendor. But systems sends an email to a different vendor other than vendor on PO.
I do not understand the relation between the Vendor on PO and the second vendor who received the E-mail.
Please help me out.

Please check your print program. If you are processing multiple PO outputs at the same time, then some variable is not getting cleared.
For eg. If in the print program, you processed PO 1,2 and 3 at the same time (via select options). 1 was email, 2 had nothing. Then if the variables are not cleared properly, the output definitions of 1 will remain until you exit the program. Please debug it with an ABAP person.
Best of luck
Lakshman

Packaging output.-URGENT

Hi Guru,
When user creating delivery and changing PGI date e.g 27/09 to 26/09 he is unable to view the output of packaging material. When he is not changing PGI date it is coming.
The same scenario I run it's working properly. I checked configuration as well as condition record are maintained properly.
I created one document and told to verify the user he told that it's coming. Then user changed PGI date of document which I created and told that out-put is not coming.Where could be the problem.
Please help.

If this is the case take help of Basis consultant.
Best Regards
Sainath

Report output - - - Urgent

I have an existing report. The first data field is concatenation of three fields and this fields data is like the following
ABCD ( X12 )
DEFF ( Y34 )
GSSD ( TST )
Here I need to get the data output in the order of values within the parentheses instead of starting values of the fields data. Desired output should be like
GSSD ( TST )
ABCD ( X12 )
DEFF ( Y34 )
To get these values I have added an order by clause to the existing query like
ORDER BY SUBSTR (field_name, INSTR (field_name, ( ) )
But I havent got the report output in required order. (ButIf I check this query in SQL I am getting the values in desired order).
Please tell me a solution to resolve this issue (because existing report is quite complex and I dont want to create this report from scratch).
Thank you in advance
Prasad
null

<BLOCKQUOTE>quote:<HR>Originally posted by Ileana Bblcu ([email protected]):
I suppose this is the master group of a query and you also have a detail group. The detail group is ordered by the order by in aselect, but the master group is ordered by the break order. Add the substr... as a column to the query. In the Data model move this new column as the first one in the group, so the break order will be dictated by it.<HR></BLOCKQUOTE>
Thank you for response... i did try that scenario before but it wasn't work.
null

Weird Issue : Difference in HTML/excel output and pdf/rtf output--Urgent

Hi There,
I am facing a weird issue. I created one rtf template. When I preview the o/p in rtf or pdf, everything comes up as expected. When I preview the same in html or excel, few rows come up as bold though they were not supposed to. What could be the problem ?
This is extremly urgent as the users primarily use the excel or html as o/p.
Thanks in advance.
Regards,
Saurabh

Hi Brett,
I am using Oracle XML Publisher standalone (not with oracle apps). The version is 10.1.3.2 . The issue comes up while previewing as well as when the report is run from the XMLP server.
Regards,
Saurabh

ME32 Outline agreement problem(when saving it issuing message output)urgent

Hi ALL,
I executing Tcode me32 and make changes on this. It will issuing output message.My need is to suppress output message while executing this in Background.Because me32 uses more than 500 PO orders.This will posted data to IDOC(For LSMW processing).IDOC uses message type BLOACH.IDOC type is basic(BLAORD03).

Hi
If the requirement is for one time data transfer then it is better to delete the condition records before the transfer and then add it again after the transfer.
( This is the way we normally do for initial data transfer ).
If its an ongoing process then you will have to use routines as IDOC will only create the document . Output processing is done by the Contract Create program itself and not by IDOC Function Module . The only thing is intead of SY-BATCH you can use some other way to distinguish whether the contract is being created by IDOC .
Now you have not mentioned whether you will use standard FM IDOC_INPUT_BLAORD or write your own Z Function for IDOC processing.
I am giving a sloution for both.
In IDOC_INPUT_BLAORD there is a user exit
EXIT_SAPLEINN_002 ( ZXM06U10 ). You can just write one line here
DATA FLAG VALUE 'X'.
EXPORT FLAG TO MEMORY ID 'BLAORD'
Or In you custom FM you can write
DATA FLAG VALUE 'X'.
EXPORT FLAG TO MEMORY ID 'BLAORD'
In the requirement routine as suggested in previous post
use
DATA FLAG.
SY-SUBRC = 0 .
IMPORT FLAG TO MEMORY ID 'BLAORD'.
IF SY-SUBRC EQ 0 AND FLAG = 'X'.
>>> C0de will branch here only when executed thru IDOCs
SY-SUBRC = 4 .
ENDIF.
With above method only when contract created thru IDOCs messages will be suppressed.
Cheers

NaN output - Urgent

Similar Messages

Maybe you are looking for