Need Help in Basic Configuration Steps

Hi,
I am trying with the scenerio for File To SAP , Please do help me in setting the Configuration step. I have completed the SLD and DESIGN section where I have done with the mappings and other required . Now when I start configuration What steps should I follow.Please do guide me for this..
I was Trying to import the Intergration scenerion from the Integration Repository for which I was exporting first the whole design for which I am getting the error
"Workspace was not defined for software component version......"
Appreciate your Help !! In Advance.
Thanks

Hey
u dont have to import anything from IR
just do the following steps in ID
>>sender communication channel(using FIle adapter)
>>receiver communication channel (using IDOC adapter)
>>sender agreement
>>receiver agreement
>>interface determination
>>Receiver determination.
thanx
ahmad
Message was edited by:
        Ahmad

Similar Messages

  • Need help on struts configuration with ColdFusion 10 using IIS

    We need help on struts configuration with ColdFusion 10 using IIS.
    Earlier we were using ColdFusion 8 with IIS 6 for one of our application.  This application internally calls struts. After upgrading to ColdFusion 10 struts calls are not loading. We get 404 error.
    In ColdFusion 8 struts were configured using  actions extension .do in IIS from this file-
    C:\ColdFusion8\runtime\lib\wsconfig\jrun_iis6.dll.
    But in ColdFusion 10 this file is not present as ColdFusion 10 uses Tomcat in place of Jrun.
    Also there is no information in ColdFusion log file.

    Duane wrote:
    doctormirabilis, Welcome to the discussion area!
    1) how can i configure the time capsule in order to operate as a remote base station synchronizing with the relay using the ethernet port?
    Configure the Time Capsule to act as a bridge (not distributing IP addresses). Also configure the Time Capsule to create an 802.11n wireless network with a unique network name (SSID). That's it.
    2) how can i avoid that my powerbook while accessing my wireless network does connect through the relay station instead of using the time capsule?
    Configure the Time Capsule to use a different network name than the WDS link between the 2 AirPort Express (AX). Configure the PowerBook to use the Time Capsule network.
    There are 2 pieces of information that you should be aware of...
    (1) None of the PowerBooks are capable of 802.11n.
    (2) The WDS link cuts your available bandwidth in half. So the wireless link to your neighbor's has a maximum potential of 27 Mbps.
    Let's for a minute assume that you have a Mac compatible with 802.11n. In your configuration the time you could take advantage of the 802.11n speed is when the Mac is sending/recieving data directly from/to the Time Capsule.
    There would be NO speed increase in Internet access. The speed of Internet access is going to be controlled by the slowest link in the path to the Internet. That is probably the connection to the ISP. The next slowest path is the WDS link to your neighbor's.
    Duane,
    I am in a similar situation, sharing internet with my neighbor. Do you think it would be plausible to hook up a vonage phone adapter to time capsule's ethernet port if time capsule is bridging from my neighbor's router in the configuration you have described? A check of my upload speed shows 1.67Mbps (powerbookG4 w/ airport extreme). Vonage reccommends 90kbps minimum upload speed. Am I going to lose some speed putting the Vonag adapter behind time capsule?
    Thank you

  • I am needing help with the final steps in restoring my iPod Touch 5

    I need help with the final steps in restoring my iPod

    I was told that the iPod would automatically go to restore mode when connected to wifi. It did not do that

  • FREE TRIAL ON PAGEMAKER INSTALLED, BUT REQUIRES STUFFIT FOR FINAL STEP.  CAN'T SEEM TO MANAGE THIS STEP. NEED HELP MANAGING THE FINAL STEPS BEFORE PAGEMAKER IS USEABLE.  THANK YOU

    HAVE INSTALLED PAGEMAKER, BUT BECAME CONFUSED WHEN "STUFFIT" SEEMED TO BE REQUIRED FOR NEXT STEP.  NEED HELP IN FINAL STEPS IN DOWNLOADING PAGEMAKER FOR USE.

    >I would like to purchase a new mac with the appropriate operating system that will
    run pagemaker 7.  If not, I understand that my current mac, Mac OS X, version
    10.6.8, processor 2.8 GHz Intel Core i7, Memory 4GB 1067 MHz DDR3 will not support
    either Pagemaker 7 or InDesign.  My question is what package can I purchase that
    will satisfy one or both of these needs?  Thank you for any guidance.
    R_Kelly  created the discussion
    "FREE TRIAL ON PAGEMAKER INSTALLED, BUT REQUIRES STUFFIT FOR FINAL STEP. 
    CAN'T SEEM TO MANAGE THIS STEP. NEED HELP MANAGING THE FINAL STEPS BEFORE PAGEMAKER
    IS USEABLE.  THANK YOU"
    To view the discussion, visit: https://forums.adobe.com/message/6607524#6607524
    >

  • Need help on variant configuration

    Hi Guru,
    Here we need to use variant configuration.But i am new in variant configuration.Can somebody tell me the different steps of variant configuration from PP side.I have gone through standard document. But still i need this information. The Industry in which I am going to implement this,is  producing Colored, profiled sheet to provide roofing solution.The metal roofing sheet can have different profile, different colour, different thickness, different width and so on.They have nearly three thousand  of different combination.
    Please respond.
    Regards
    Rajib

    Hi,
    Pls. find herewith Variant Configuration Procedure steps as below
    VARIANT CONFIGURATION:
    1.Create a Material - KMAT type with Item category (002)
    2.Create Charateristics in CT04 - Zbike, where in values mention the Color of the bile like Red, Blue etc
    Create another characteristics in CT04 - ZPrice, where directly go the additional data tab and maintain the table SDCOM and field VKOND (ABAP Dictionary it will ask for).
    3.Assign these two characteristics to a Class in CL01 - ZBikeclass ( Type 300) in characteristics tab page.
    4Then go to CU41 Configuration profile select the material and enter the description click on the class assignment ie assign Zbikclass.
    5Now go back to CT04 - enter Zbike -go to values- select Red- go to extras - Other Dependencies - Select Procedure enter in front 10 write - $self.ZPrice='Red' and save.
    6.Now go back go to extras - Other Dependencies - assignments and assign relationship ( by default it will come just save).
    7.Now select Blue- go to extras - Other Dependencies - Editor - Select Procedure enter in front of 10 write - $self.ZPrice='Blue' and save.
    8.Now go back go to extras - Other Dependencies - assignments and assign relationship ( by default it will come just save).
    9.Now go to VK11 - Enter VA00 (Condition)(For Std RVA001 Pricing Procedure) - enter variant Red and Blue give the rates accordingly and create the sales order.
    Variant Configuration: Complete Maintenance:
    Technical name: SAP_LO_VC_MAINTAIN
    Tasks
    The variant configuration processor sets up the rules for multi-variant products and maintains them in the database. He or she simulates and executes the configuration. This role is required wherever variant configuration is used.
    The complete model also contains sales order processing (VA01/VA02), and the connection to SCE/Internet Sales and Mobile Sales.
    Activities in Variant Configuration;
    Transaction
    Activity
    CC04
    Display product structure
    CWBPP
    Engineering Workbench
    Variant Configuration
    VA01
    Create sales order
    VA02
    Change sales order
    VA03
    Display sales order
    CU51
    Maintain configurable order BOM (multilevel)
    CU52
    Maintain configurable order BOM (single level)
    CU50
    Configuration simulation
    CU80
    Reporting functions for characteristics and values
    Configured Objects
    CU44
    Material
    CU45
    Standard network
    Assignment of Configured Materials
    CS40
    Create assignment for configured material
    CS41
    Change assignment for configured material
    CS42
    Display assignment for configured material
    Configuration Profile
    CU41
    Create configuration profile
    CU42
    Change configuration profile
    CU43
    Display configuration profile
    Dependencies: Single Dependency
    CU01
    Create single dependency
    CU02
    Change single dependency
    CU03
    Display single dependency
    Dependencies: Dependency Net
    CU21
    Create dependency net
    CU22
    Change dependency net
    CU23
    Display dependency net
    Dependencies: General
    CU05
    Dependency where-used list
    CU04
    Dependency list
    Tools: Variant Function
    CU65
    Create function
    CU66
    Change function
    CU67
    Display function
    CU68
    List functions
    Variant Table Structure
    CU61
    Create variant table
    CU62
    Change variant table
    CU63
    Display variant table
    CU64
    List variant tables
    Variant Table Contents
    CU60
    Maintain variant table contents
    CU59
    Transfer variant table contents to database table
    Knowledge Base for SCE: Knowledge-Base Object
    CU31
    Create knowledge-base object
    CU32
    Change knowledge-base object
    CU33
    Display knowledge-base object
    Runtime Version
    CU34
    Create runtime version
    CU35
    Change runtime version
    CU36
    Display/export runtime version
    CU37
    Create SCE database schema on PC
    For complete details of Variant Configuration go to the following link :
    http://help.sap.com/erp2005_ehp_03/helpdata/EN/96/468f38721f9977e10000009b38f842/frameset.htm
    Hope this helps.
    Regards,
    Prakash

  • SolMan 7.1 Configuration:Basic Configuration -Step 2

    Hi All,
    I completed the upgradation of SolMan 7.1 with SPS04 and did the System preperation and Basic Configuration.(txn:solman_setup)
    In the Basic Configuration at the step #2 - Specify User & Connectivity Data I'm still seeing the yellow simbol(Activity Warnings), but within this step all the sub steps( 2.1 to 2.5) are in Green mode.
    Do you guys know how to remove this yellow symbol on the step#2?
    Thanks,
    Allam

    Hi,
    please follow the sap note
    [Note 1498701 - Yelow status for Create Users when a local BW system is set|https://websmp130.sap-ag.de/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/sapnotes/index2.htm?numm=1498701] to fix this
    Thanks,
    Jansi

  • Need Help W/ Raid Configuration

    I NEED HELP W/ MY RAID CONFIGURATION.
    I HAVE THE K7N2 DELTA-ILSR MOBO W/ A XP2600+, I HAVE TWO 40 GIG HARDDRIVES THAT I WANT TO RAID 0 TOGHTER.
    I HAVEN'T FOUND IN THE MANUALL HOW TO SET UP THE RAID ARREY, I DONT NO HOW TO SET THE DRIVER AS FAR AS SLAVE/MASTER SETTINGS, WITCH ONE NEEDS TO GO TO WITCH CHANNEL ( PRIMARY/SECONDARY/CS).
    - EVERY TIME THAT I SET IT UP THE ARREY IS SHOWING ONLY 1 DRIVE, I BELIVE THAT RAID 0 SHOULD HAVE BOTH OF THE DRIVES AS 1 BIG DRIVE, CAN SOME ONE HELP ME W/ INSTARUCTIONS HOW TO CREATE THIS ARREY?
    thanks guys

    I had RAID 0 set on my system. I used the MSI Live Update software to update my RAID controller because it said it needed it. It hung up in the middle of the update, so I let it sit for 24 hours. Finally I rebooted, & now it won't even see the drives. If you go with RAID 0, back up your data, and keep it backed up!!! I will say this, while it worked, it was really really fast!!! In order to make my RAID work (while it lasted) I used two SATA drives. I believe you can also use one ATA & 1 SATA instead of two SATA drives. If you use 1 ATA drive, set it to master & connect to IDE 3. This will be the only drive on that cable. During the boot up, you have to follow the prompt & press to enter the FastBuild (tm) Utility. Once there, you can choose Auto Setup & it will do the work for you. I must re-iterate, KEEP YOUR DATA BACKED UP!!!!!! I hope this helps. Good luck!
    K7N2G-ISLR, AMD 2600+, Twin rapter 37gb hard drives, 1gb DDR-400, G-Force FX
    5600 256mb AGP etc.

  • NEED HELP WITH WORKFLOW CONFIGURATION

    I need help with 3 situations below. Please help me with these. How do I configure these. I also haveto provide specs to the Abaper. What exactly do I need to include in the specs. I anyone has the specs similar to these please send me over. Also tell me what I need to do to get these requirements fulfilled.
    1)  Description:
    This is a workflow requirement to serve as a reminder of upcoming investment
    maturities.
    Requirements Details:
    Create a workflow to serve as a reminder of upcoming investment maturities.
    Donor System Processing Narrative:
    Read the maturity dates on investments.
    Target System Processing Narrative:
    Send a notice to the parties that an investment will be maturing soon.
    2)  Description:
    Implement workflow to route invoice receipts using a one time vendor for management
    review and posting
    Desired Functionality:
    If a one time vendor is entered by the AP Voucher Clerk the invoice will be automatically
    parked by the program and a workflow notification triggered to the Accounting
    Supervisor and Accounting Manager (backup). The Accounting Supervisor will review
    the parked document and imaged copy of the actual invoice and post the parked
    document.
    3)  Description:
    An approval workflow is needed for credit memos posted to SAP customer accounts.
    Desired Functionality:
    The Cash Journal Clerk will post a credit memo to the customer account using transaction
    FV75 Park Customer Invoice. This transaction will automatically trigger a workflow to
    the Accounting Manager for approval and then to the CFO who will approve and post the
    parked document. (In order for this transaction to automatically trigger what configuration needs to be done).

    Bob;
    You can borrow the example code that ships with both NI-DAQ (in case you are doing NI-DAQ function calls) and Labview. The best examples to start with are the ones that have the prefix STC.
    Hope this helps.
    Filipe A.
    Applications Engineer
    National Instruments

  • Need help with AS8 configuration

    Our present situation is like this:
    AS7 with single domain and multiple server instances
    instance A running on port xxx containing app1
    instance B running on port yyy containing app2
    instance C running on port zzz containing app3
    Now, when I move to AS8.1 PE, I dont see the option to create a server instance inside a domain. I need to create 3 domains in order to accomplish the same task as above. Not only that, now I need to login to 3 different admin servers to manage the 3 apps on 3 ports
    I need help with some options I can use
    thanks

    I'm not sure but i think that on 8.1 pe you can have only one server instance by default...
    But you can olso try by command line tool asadminin [installdir soas]/binuse:
    asadmin --help for a list of commands available.
    In the list should be create-instance to create a stand alone instance.
    Hi
    Stefano

  • Need help with basic steps in creating ebook

    I have a confession: I constantly use workarounds instead of stopping and learning the proper way of using Indesign to create ebooks. I wouldn't say I do it because I'm lazy, but rather because I'm simply inept lol. These are some of the basic steps I take:
    1. create new document: include master text frame (because I want page numbers to show)
    2. paste unformatted text into document
    3. adjust size of master frame to give text suitable margins (since its an ebook, right/left margins same on opposing pages.)
    4. highlight all text, adjust before- and after-paragraph spacing to half of the character leading (so bottom of text is at same point for each page)
    5. go to chapter titles; do page-break so title has its own page; highlight title, choose font, size; create new character style; apply style to other chapter titles (is it possible to create a ctrl + number shortcut to apply character styles?). Notice I didn't create a character style for body text. Should I do that first?
    6. insert page number markers on both master pages, then cover page number with white box on first page of chapters.
    7. drop pictures into textbox so that if more text is added, pictures move with the text.
    That's basically what I do when I create an ebook. Any suggestions as to better/proper way to do these things would be very appreciated.

    1. Master text frames have nothing to do with page numbers and in most cases are totally unnecessary. Set the margins appropriately and place your text.
    2. Without knowing what you're starting with it's impossible to tell if that's a good idea or not. My gut says is it's not. See number 1.
    3. See number 1.
    4. This is what paragraph styles are for.
    5. See number 4.
    6. This is what multiple master pages are for. Stop doing that.
    7. Well, you finally got one right. As my people would say...mazel tov.
    Now, it's time for you stop being inept (your word, not mine) and start learning the right way to do this. First thing you do is buy Sandee Cohen's Visual Quick Start Guide. It's the best InDesign book on the market for beginners. http://amzn.to/plsvxy
    Secondly, check out the video training on Lynda.com. This link will get you a free one week trial: http://bit.ly/fcGpiI
    Bob

  • 100% Noob - Need Help for basic setup of Cisco 2504 and 1600 AP

    Hello,
    I am completely noob in (cisco) networking.
    I have to setup a basic but secure wireless network.
    I have a cisco 2504 and 2 APs 1600 + a random switch
    I have 4 ports on the controller.
    I want to keep the 1st port on the network for the controller management, plug my internet box on the 3rd port, and my switch on the 4th port. Then the AP will be on the switch.
    I am able to make something working when everythings are plugged on the switch, plugged in the first port (default management port).But this is not what I want.
    First thing, Is that possible ?
    1st port : office network
    2nd port : empty
    3rd port : Internet Box
    4th port : Switch + all APs
    Then, if that is possible, how should i configure the controller to make that work ? I am completely lost in the menus.
    I dont need a perfect configuration, just something simple and working.
    1 SSID, 10 DHCP addresses, block wireless users trying  to go on the office network.
    If anyone could help my doing that, It would be very nice.
    Thank you.

    You basically need two SSIDs one for corporate users and second for guests .check the link with  step by step config and brief details .
    http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/70937-guest-internal-wlan.html

  • New to Photoshop (CS4Ext) and need help with basic loading of images to new folder.

    Just purchased CS4Ext and installed it. It's not showing up on my desktop as a quick entry icon. I want to simply load images from a portable hard drive (USB) to a new folder in photoshop so I can review them and begin to select  and separate out some of interest to manipulate  and share or get ready to print. It 's the most basic help one can need butI'm jut not clear on the workflow steps . Would appreciate someone walking me through the steps .
    Thanks much

    drmjp2 wrote:
    Just purchased CS4Ext and installed it. It's not showing up on my desktop as a quick entry icon.
    Let's see…   First of all, this is the Photoshop Macintosh forum.  Installed applications never, ever show up on your desktop as a "quick entry" icon on a Mac.  Are you on a Windows PC maybe?
    drmjp2 wrote:
    I want to simply load images from a portable hard drive (USB) to a new folder in photoshop so I can review them and begin to select  and separate out some of interest to manipulate  and share or get ready to print.
    Just select them with your mouse in the Finder and drag-copy them into the new folder.  Done.

  • Need help in post-installation steps of the PDK

    Hello,
    I have installed Java PDK 6.9 instead of 6.2.
    At the post-installation steps I need to:
    <i>The example iViews in the Portal Development Kit connect to a SAP System with the system alias PDK_R3_BACKEND.
    To run these examples you must define a system object for a test SAP System in your system landscape and assign the following aliases:
    1. PDK_R3_BACKEND Reference to a R/3 system of your custom landscape.
    2. PDKDummySystem Reference to provided system OBN-3. PDKDummySystem.
    WebDynpro Reference to provided system WebDynpro.</i>
    My question is: When I create this System, which type template should it be and which configuration besides the above aliases should it have?
    Roy

    Hey Aviad,
    Yes I did, in my case I've installed PDK SP 9 over SP2 which is prohibited. If this is your case as well do the following:
    1) From the Undeployment tab of the SDM select the com.sap.pct.pdk..
    components.
    2) Using the Archive remover tool which can be accessed from
    System Administration > Support > Portal Runtime > Administration
    Console > Archive Remover --> Remove the portal applications with prefixcom.sap.pct.pdk...
    3) Navigate to Content Administration > Portal content > Content
    Provided by SAP > Platform Add-Ons > Developer Content
    and remove all the contents below this folder.
    4) Restart the server
    After this you can deploy the SP9 business package using the SDM.
    Hope it helps,
    Roy

  • Large processing in ADF BC 10.1.3.4 - need help on AM configuration

    I working in Jdeveloper 10.1.3.4 and ADF BC. I have some large processing and processing is getting slower over the time. For example:
    I procces tens of thounsend records over ADF BC. I get one record, do some preocessing, update that record and create new one. At begin speed is 100 records per seconds, but it slowing and on 10000 record is 10 records per second. Xms param is set to 1024M and AM configuration is not changed. Do you have some advice? Do I need some adjustments of AM configuration? Any help?
    Also I’m working on some billing system and I have similar problem. I start processing in separate thread and that work corectly, but after some time (say 1 hour and ten thousend custumers) I catch error say ‘invalid operation with view object’. I catch that error, but can’t continue proccesing. I guess that is also some problem with resources. If anyone have similar problems, please HELP :)

    Dragan,
    If you are talking about iterating over VO records - have a look at the VO tuning parameters, especially if you are using range paging mode. In range paging mode, the performance of getting the next set of rows degrades as you proceed through the result set.
    John

  • Need help with AAA configuration

    I am trying to configure AAA on my network devices. I am using TACACS+ with an ACS (3.2) server. I have setup two user groups in the ACS server, one with enable priviledges and one without. I am able to get the AAA configuration to work when telnetting into the devices. However, when logging into the console port, the user group with enable priviledges do not go directly into enable mode as the telnetted users do. How to fix this?

    Hi,
    You will need to use the following command :-
    aaa authorization console
    This command will not show up on the help.
    Regards,
    Vivek

Maybe you are looking for