Netboot MAC Address filter settings do not hold

I was able to find this fix for getting the Model property settings to stick:
* Stop Netboot
* Uncheck Enable image
* Make the change
* DO NOT click "Save"
* Check Enable image
* Start Netboot
but the MAC Address filtering settings do not stay
Any ideas? My Xserve is running 10.5.5 with all of the latest updates.

Setting "per image" filtering does not work. This is a known issue. You can set filters for the entire server however.

Similar Messages

  • MAC address filter on router does not work for iOS8

    The MAC address randomization feature in iOS8 is great for privacy, but this being the case, I am not able to connect to a wi-fi router that employs a MAC address filter. Is there a way to turn off this MAC address randomization?

    I had this problem. I followed the directions to replace the netinfo db's. I rebooted, and started going through the initial OS X welcome stuff. When I tried to re-enter my user stuff, I got a "sorry, standard user cannot be added" error, and the machine went to a blue screen.
    This is odd, as I have completely restored the system from scratch (reformatted the hard drives, reinstalled). The first boot up it works fine. It seems that one of the updates must be screwing it up, because after it gets through updating, when it reboots, I can't log in.

  • WRT54GL MAC ADDRESS FILTER

    Hi I have a wireless access point WRT54GL and i configure it with mac address filter but it allow me to put only 40 mac and i need more? Is there any way to add more? Thanx

    Install 3rd party firmware like dd-wrt or hyperwrt+thibor. That should give you more. However, remember a bad flash may brick the router and is not covered by warranty.
    Also remember, that the wireless mac address filter does not provide you with any reasonable security. MAC addresses are quickly captured and quickly cloned. It only takes a few minutes to gather some mac addresses which are allowed into your wireless network and that's it.
    Set up wireless security with WPA2 or WPA and a strong passphrase. That's all you can do to really protect your wireless.
    If you want more detailed access control, consider installing a RADIUS server and using user/password authentication based on WPA2 or WPA (using the RADIUS or Enterprise variants).
    But the wireless mac address filter is widely overrated as security mean and only requires a lot of work and time to maintain the lists.

  • WRT610N: Cannot enter MAC address in MAC address filter list

    My WRT610N cannot accept a very specific MAC address in any position of the MAC address filter list.  It is a valid address and it was working fine in the filter list of my WRT54G but the 610N will just not take that specific address!  What is this all about?
    Solved!
    Go to Solution.

    gv wrote:
    There is nothing like a "non-critial setup". It's enough to drive by with a car and within a few minutes your network is hacked. Or it's the bored teenager next door...
    I recommend to replace the WEP only device instead of taking the risk of a hacked network.
    And just forget about the wireless mac address filter. Anyone, who wants to crack your WEP network will collect enough accepted MAC addresses during the cracking process. It's just not worth the trouble to set up the filter and keep the list current...
    Thanks for the diligent follow-up gv but I can't replace the WEP-only device for now.  (I need to go through a conversion process for that device to accept WAP and that will take a fair amount of time)  I understand your point about getting accepted MAC addresses but, at least, it requires a bit more effort... Maybe I will return the WRT610 and stick with my old WRT54 until the 610 gets fixed...

  • WRT54GS - MAC Address Filter & Firewall SPI

    Hi,
    I just purchased a WRT54GS V 6 wireless router.  I updated the firmware to the latest (May 30) and the set up seems to be OK.  Using the security recommendations in the manual as a guide, I implemented them - the turn off SSID, and the others. 
    IF I try to filter the MAC addresses (accept only those on the list) for my wife's Sony VAIO VGN - S260 laptop, it can see the network but will not connect. When I turn off the MAC filtering, it is fine.  I used the WPA2 personal encryption, and input the passphrase into both router and computer. 
    My other issue is the firewall Statefull Packet Inspection (SPI).  On the Security set up screen, firewall tab - I have the four radio button settings that I am supposed to (Block WAN request, filter Multicast, Filter NAT, & Filter IDENT), however, I do NOT have the option to turn on the firewall (SPI) above the 4 radio buttons - that setting is totally missing from the set up screen.  Reference Page 28 of the manual.
    I would appreciate any help or suggestions, as I could not find any ideas searching the forum.  Thanks for your help
    Message Edited by donh127 on 08-07-2006 07:00 PM

    Hi. Is your Mac mini loaded with the OSX server edition or OSX consumer edition? I am not 100% sure but I think you need a server edition to do that.

  • E 2500. Mac Address Filter. Improvement. Sugestion

    Hi, what brings me here is a suggestion for improvement in the product management software. Where you make any configuration and / or alteration.
    My suggestion concerns the application of the 'MAC Number filter'. This application allows you to add devices that may or may not access the Linksys E2500.
    It turns out that the current version of this management software, to insert into the list (restrictive or permissive) of ' MAC  Number filter'. This insert serves to both wifi networks generated (2.4 GHz and 5 GHz).
    In my case the core network for home use is the 5 GHZ. And the 2.4 GHz network was set to 'guests'.
    So, when someone comes to my house is either use the 'Network - Guest' can only be used if:
    1- If I'm applying MAC address filtering for my household devices - must have to individually enter the MAC address of each guest; or
    2- Do not use for my home devices MAC number Filtering
    I understand that this security feature (MAC number Filter) is very good and helpful. But the way it is designed is not practical.
    My suggestion is to update the management / configuration software to enable:
    A) The owner can set Allow List or Prohibition of the home devices in the MAC number filter separately. In the 5 GHz network (main). Leaving free the Guest Network;
    B) Provide the update mentioned in item 'A' (above) also in Cisco Connect application.
    Thank you for your time and attention.

    I think other manufacturers follows the same MAC address filtering protocol but I'm cool with your suggestion and it might be implemented in the future by Linksys. Enabling the Guest Access on the router's setup page (Wireless tab > Guest Access) will ease you out of the hassle of inputting the MAC addresses of your guests' wireless devices. Your visitors will still be able to connect to the guest network even if the MAC address filtering is enabled but those will have limited access to your network.

  • Is a MAC address filter incompatible on an extended network?

    Hello all,
    I've bought myself an Airport Express and an Airport Extreme.
    The Express serves two roles:
    1. Play music
    2. Extend my network (a real extension, not just a network join)
    On my Extreme, I've setup MAC address filtering with a time-based access (to avoid hacking of my network during the night -- don't worry, I have WPA2 security too...). Here's what I've done:
    - All devices: no access from 11 PM to 7 AM
    - Airport Express: always access
    - Macbook Pro: always access
    So far, so good.
    Now, the problem I see if the following: IF my Express has access anytime, then an unknown device CAN connect to my network at night (midnight for example) simply because it will connect on my Express instead of my Extreme! It's like an unlocked back door!
    So, from what I see, when I extend a network, the MAC filtering is not passed along to the "extending" devices. Also, on an extended network, I CAN'T set a MAC filter... So I'm stuck with an unsecure extending device.
    So, my question is the following: is this normal behavior or is this an oversight from Apple? In other words, how can I extend my network and "propagate" my security setting on all my devices?
    Thanks!
    P.-S. On another topic, but related, any idea how to apply a setting without rebooting the router everytime? This is very annoying.

    HI Yes this works fine. I have these  wifi base stations these configurations on the same subnet in my place *using MAC filtering (access control)* in two extended networks.. Here's how I do it.
    • AEBS 802.11n@5Ghz 9DHCP and WAN.. and MAC ADDRESSES. TimecapsuleTV = SSID="my5Gwifi" , closed network
    • 1 x AEBS 802.11g 2.4Ghz snow coloured dome base station (connected through ethernet to the main 802.11n AEBS) + 2 x 802.11g APx's + 802.11N APX; closed network; name | SSID ="my2.4Gnetwork"; all bridge mode. FOr WDS add all MAC addreses of all devices like iphones, ipods, macs, pea-seas, PS2's etc and the other APX base stations too!.
    Here's the deal:
    for the 802.11N base stations (AEBS . TC or APX gen 2), the extensible wifi stations are through '+extend this network+" in the + Airport Utility+.. There is no provision for the extension stations to addf any ACCESS control if you use BRIDGE MODE> (as I would you to do advise).
    • for the *802.11g or WDS* I have found that you must ADD all the MAC addresses in EACH of the base statsion. This is simple to do my exporting all teh mac address config lists and importing them as you need. THis works fine.
    My company registers world wide all laptop wireless nics. We have over 300,000 employees (3 x 10**5) all dynamically VPN'ed adn mac address filtered for windows , linux and unix. it works for them worldwide. Walk into any office and you are connected.
    As for me and others WEP, WPA2 and all that is a mess around for hours (with that awful redmond based software) with frustrating and a huge waste of time when some one tries to connect to your system with some of those ghastly microsoft opertating systems. They all have their quirks. Vista - well you mostly know.
    In any case the simplest and I beleive effective for most is MAC ADDRESS fitering.
    FWIW all ways can be infiltrated.. you just need to monitr your network or add a GBE hub and use cables where the cables are in a locked oom.
    hth
    w

  • Ipad contacts not displaying all fields from mac address book, ipad contacts not displaying all fields from mac address book

    After syncing mac address book to ipad contacts, the ipad does not display all the fields that were in Mac address book (in my case all the email addresses).  Anyone have a fix?

    I have a problem similar to DeeRun's.. I would like the IM fields to be synced.. I use them to send e-mails to when the e-mail field is empty or when i just want to use that specific address.. Very annoying, would take hours if not days to transfer all those IM adresses to e-mail fields in addressbook..
    EDIT: not to mention the mess it would make in my address book!
    Message was edited by: 1NStanley

  • Mac address filter

    Is it possible to identify the visitors mac address using PHP
    if yes is there anything to prevent you from limiting access to specific mac addresses (say by using an IF statement to redirect other users to a different site)

    You can identify the IP address, but that doesn't take you down to the level of the individual machine.
    Barry

  • Slide Show settings will not hold

    I can't get my slideshow to change from the dissolve transition mode to any thing else. I change the transition in three different places, but i still get the same results.
    What am I doing wrong?
    I'm using Iphoto 6.0.5. My slideshow has about 2000 pics if that might matter.
    Thanks!!!!!!!

    laturner66:
    Welcome to the Apple Discussions. Try deleting the iPhoto preference file, com.apple.iPhoto.plist and all of the contents of the User/Library/Caches/iPhoto folder. Then see if those changes will stick.
    Do you Twango?
    TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
    I've written an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.

  • Cannot get to the Mac address!

    Hi everyone,
    We used to be able to connect our Wii to our wireless connection with a few clicks, now after we haven't had the Wii plugged in for about a year it can't seem to connect anymore, all though nothing changed on my airport side, the WEP password is the same, I tried retyping it a few times and that did nothing.....anyways, we went to the Nintendo support site and they also recommend the following:
    1. If your WEP or WPA key is correct, then the problem might be related to MAC address filtering:
    1. From the router settings, locate the "MAC address filter" settings (also known as "access control", "access list", or "network filter" depending on your router model).
    2. If the Mac address filter is set to "enabled", then you must add the Wii's MAC address to the "allowed" list. You can locate the Wii's MAC address from the "console information" page (located under "Internet" in the Wii Settings).
    3. If the Mac address filter was disabled, then continue troubleshooting.
    now, I am not able to access my airport utility, I put in the WEP password its asking for and it keeps coming back for it............so , I cannot access that panel, but I can't find a place to add a Mac address in the network preferences for the airport!???
    Help?
    Thank you,
    Lucia

    Ok, here's the basic step-by-step to get your AX up-and-running to get Internet access from a cable modem ...
    Perform a "factory default" reset of the AX
    o (ref: http://docs.info.apple.com/article.html?artnum=108044)
    Modem/Router Power ReCycling
    o Power-off the Cable modem, AX, & computer(s); Wait at least 5 minutes.
    o Power-on the Cable modem; Wait at least 15 minutes.
    o Power-on the AX; Wait at least 10 minutes.
    o Power-on the computer(s)
    Setup the AX
    Connect to the AX's wireless network, and then, using the AirPort Admin Utility, try these settings:
    AirPort tab
    o Base Station Name: <whatever you wish or use the default>
    o AirPort Network Name: <whatever you wish or use the default>
    o Create a closed network (unchecked)
    o Wireless Security: Not enabled
    o Channel: Automatic
    o Mode: 802.11b/g Compatible
    Internet tab
    o Connect Using: Ethernet
    o Configure: Using DHCP
    o WAN Ethernet Port: Automatic
    Network tab
    o Distribute IP addresses (checked)
    o Share a single IP address (using DHCP & NAT) (enabled)
    Once you verified that you can get Internet access for all of your computers, you should secure your wireless network. To do so, I suggest that you make these changes:
    Change Wireless Security
    o Wireless Security: WPA Personal or WPA2 Personal
    o Encryption Type: WPA and WPA2
    Base Station Options - WAN Ethernet Port
    o Enable Ethernet Port (checked)
    o Enable SNMP Access (unchecked)
    o Enable Remote Configuration (unchecked)
    o Enable Remote Printer Access (unchecked)

  • ARP table not populating mac address for previously reachable IP address

    Router has been online and working fine with one BGP neighbor for almost 2 years and no downtime.  2 weeks ago, added a 2nd BGP peer.  Everything worked fine for 2 weeks, then all of a sudden yesterday the 2nd BGP peer is disconnected and does not come back.  ISP checks and sees everything looks fine on their end.  We cannot even ping each other now.
    Upon investigation, the ARP table is not even populating the MAC address for the BGP peer IP anymore (same local subnet).  Stays "incomplete" in the table no matter what we do, including clearing arp table, changing IP address, etc.
    Plug a laptop directly into the 2nd BGP peer FE port and replicate the IP addressing.  Laptop cannot ping Router, but Router CAN ping laptop.  Check ARP table, but STILL no mac address assigned and now not even the ARP table showing "incomplete".
    Thinking it could be the FE interface, switch to the 2nd FE interface and perform same laptop test, this time with arbitrary IP addressing.  Now cannot ping each other, no MAC in ARP table.
    End up rebooting the router and lo-and-behold, everything is working normally again.  2nd BGP peer peers up instantly.
    I should also mention that the 1st BGP peer worked flawlessly throughout, taking all the Internet load and having no issues throughout.
    Also, the FE ports for the 2nd BGP peer are on an HWIC FE card plugged into the router.  The 1st BGP peer is plugged into the built-in GE interface.  2901 running: c2900-universalk9-mz.SPA.151-4.M4.bin
    Lastly, no router resource issues, no error messages, no logs.  Just the BGP peer disconnecting.
    I have never, in 20 years working with Cisco routers seen something like this before.  This is the most fundamental aspect of IP and Ethernet that was not working.
    Has anyone ever seen this behavior before??
    Here is the router config (IP's changed):
    version 15.1
    service timestamps debug datetime msec localtime show-timezone
    service timestamps log datetime msec localtime show-timezone
    service password-encryption
    service internal
    service sequence-numbers
    boot-start-marker
    boot-end-marker
    logging buffered 150000
    aaa new-model
    aaa authentication login LAUTHEN local
    aaa authentication login TAUTHEN local group tacacs+ enable
    aaa authorization console
    aaa authorization exec LAUTHOR local if-authenticated
    aaa authorization exec TAUTHOR local group tacacs+ if-authenticated
    aaa session-id common
    clock timezone PST -8 0
    clock summer-time PDT recurring
    no ipv6 cef
    no ip source-route
    ip cef
    no ip domain lookup
    multilink bundle-name authenticated
    username ubiadmin privilege 15 secret 4 .JbeuWXuZvchrG0OL.5BftFtqrrEyxcnVHn5rIuCnTk
    username umitsnoc01 privilege 15 secret 4 cUmoRUjey9O1x.wk9S.kleX.iAAhCwihupr6Z98p6OA
    redundancy
    ip ssh version 2
    track 1 interface GigabitEthernet0/0 line-protocol
    class-map match-any AutoQoS-VoIP-RTP-Trust
     match access-group name SIP-Media-INBOUND
    class-map match-any AutoQoS-VoIP-Control-Trust
     match ip dscp cs3
     match ip dscp af31
    class-map match-any Customer-Voice
     match access-group name Customer-VPNs
    class-map match-any media
     match access-group name SIP-Media
    class-map match-any signaling
     match access-group name SIP-Signaling
    policy-map AutoQoS-Policy-Trust
     class AutoQoS-VoIP-RTP-Trust
      priority percent 70
     class AutoQoS-VoIP-Control-Trust
      bandwidth percent 5
     class class-default
      fair-queue
    policy-map queue
     class signaling
      bandwidth percent 5
     class media
      priority percent 50
     class Customer-Voice
      priority percent 40
     class class-default
      fair-queue
    policy-map shape
     class class-default
      shape average 10000000
      service-policy queue
    interface Embedded-Service-Engine0/0
     no ip address
     shutdown
    interface GigabitEthernet0/0
     description BGP Peer 1
     ip address 2.2.2.2 255.255.255.252
     no ip redirects
     ip flow ingress
     ip flow egress
     duplex auto
     speed auto
     service-policy output shape
    interface GigabitEthernet0/1
     description LAN
     ip address 1.2.3.4 255.255.255.0
     no ip redirects
     ip flow ingress
     ip flow egress
     standby 255 ip 1.2.3.1
     standby 255 priority 105
     standby 255 preempt
     standby 255 mac-address 1a2b.3c4d.5e6f
     standby 255 track 1 decrement 10
     duplex auto
     speed auto
     service-policy output AutoQoS-Policy-Trust
    interface FastEthernet0/0/0
     description BGP Peer 2
     ip address 1.1.1.1 255.255.255.252
     ip flow ingress
     ip flow egress
     duplex full
     speed 100
     service-policy output shape
    interface FastEthernet0/0/1
     no ip address
     shutdown
     duplex auto
     speed auto
    router bgp 7777
     bgp router-id 2.2.2.2
     bgp log-neighbor-changes
     network 1.2.3.0 mask 255.255.255.0
     neighbor 1.1.1.2 remote-as 5555
     neighbor 1.1.1.2 update-source FastEthernet0/0/0
     neighbor 1.1.1.2 prefix-list L3-DEFGW in
     neighbor 1.1.1.2 route-map L3-LPREF-IN in
     neighbor 2.2.2.1 remote-as 6666
     neighbor 2.2.2.1 ebgp-multihop 2
     neighbor 2.2.2.1 update-source GigabitEthernet0/0
     neighbor 2.2.2.1 send-community
     neighbor 2.2.2.1 prefix-list COLO-DEFGW in
     neighbor 2.2.2.1 route-map COLO-LPREF-IN in
     neighbor 2.2.2.1 route-map COLO-OUT out
    ip forward-protocol nd
    ip bgp-community new-format
    ip as-path access-list 5 permit _5555_
    ip as-path access-list 5 deny .*
    ip as-path access-list 10 permit ^6666$
    no ip http server
    no ip http secure-server
    ip flow-top-talkers
     top 50
     sort-by bytes
    ip route 0.0.0.0 0.0.0.0 1.1.1.2 254 name L3
    ip route 0.0.0.0 0.0.0.0 2.2.2.1 255 name COLO1
    ip route 10.0.0.0 255.0.0.0 10.10.10.10 name FW_OUTSIDE
    ip tacacs source-interface GigabitEthernet0/1
    ip access-list standard SNMP_SOURCES
     permit 12.12.12.0 0.0.0.255
     deny   any log
    ip prefix-list L3-DEFGW seq 5 permit 0.0.0.0/0
    ip prefix-list COLO-DEFGW seq 5 permit 0.0.0.0/0
    ip prefix-list COLO-LPREF-OUT seq 5 permit 1.2.3.0/24
    route-map COLO-LPREF-IN permit 5
     match as-path 5
     set local-preference 250
    route-map COLO-LPREF-IN permit 10
     set local-preference 150
    route-map COLO-LPREF-IN permit 20
    route-map COLO-OUT permit 10
     match ip address prefix-list COLO-LPREF-OUT
     set as-path prepend 7777 7777 7777
     set community 29795:1004
    route-map COLO-OUT permit 20
    route-map L3-LPREF-IN permit 10
     match as-path 10
     set local-preference 200
    route-map L3-LPREF-IN permit 20
     set local-preference 150
    snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
    snmp-server enable traps vrrp
    snmp-server enable traps flowmon
    snmp-server enable traps transceiver all
    snmp-server enable traps ds1
    snmp-server enable traps call-home message-send-fail server-fail
    snmp-server enable traps tty
    snmp-server enable traps license
    snmp-server enable traps envmon
    snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
    snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
    snmp-server enable traps flash insertion removal
    snmp-server enable traps mac-notification
    snmp-server enable traps aaa_server
    snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
    snmp-server enable traps memory bufferpeak
    snmp-server enable traps config-copy
    snmp-server enable traps config
    snmp-server enable traps config-ctid
    snmp-server enable traps event-manager
    snmp-server enable traps hsrp
    snmp-server enable traps cpu threshold
    snmp-server enable traps rsvp
    snmp-server enable traps syslog
    snmp-server enable traps vtp
    snmp-server enable traps ipsla

    When you were checking the ARP table was there an entry for Fast0/0/0?
    HTH
    Rick

  • Airport MAC address not set at factory?

    I just received my new MacBook Pro and was getting ready to set my router so that DHCP requests from the new Macbook Pro would receive the same IP address on my home LAN.
    The IP address for the Airport in my new machine is: 00:11:22:33:44:55 as determined by the following terminal command.
    macbookpro:~ pderby$ ifconfig en1 | grep ether
    ether 00:11:22:33:44:55
    I tried to "spoof" the address with this command:
    sudo ifconfig en1 lladdr 00:19:e3:d8:f5:07
    which does not throw an error, but does not work.
    Anyone else get a MacBook Pro where the MAC address for the airport was not set?
    Any ideas on what to do?
    I suppose I can just tell my router the MAC address is 00:11:22:33:44:55

    Of course the MAC address and the IP address are two different things. I'm not sure why, Kappy, you thought I had this confusion. And I beg to differ, but MAC addresses are by interface, not by machine. So the ethernet port has a different MAC address than the Airport. They HAVE to have different MAC addresses or using two IP connections at the same time will not work when both ports are active at the same time and have the same MAC address. Using both ports at the same time with two independent IP addresses is completely supported by BSD Unix as well as OS X.
    On my new machine the Ethernet Port EN0, has the MAC address 00:23:32:c8:27:4a
    On my new machine the Airport Port, EN1, has the MAC address 00:11:22:33:44:55
    I've had a lot of Macs, and this is the first time I've had an airport with this "default" MAC address.
    My question is 1) does anyone else have a MAC address of 00:11:22:33:44:55 on their new MacBook Pro for the Airport hardware? If so, is this correct? Usually the MAC address has a manufacturer's Id embedded followed by a unique ID. 2) If someone is in the same situation have you talked to Apple about this? What did they have to say?
    I can spoof the MAC address temporarily via the terminal, but it will reset to the hardware address on reboot.
    Message was edited by: Paul Derby

  • Printing From PSE12 - settings not holding/prints are inconsistent.

    Printing from PSE12, MacOS with PSE12 controlling color/appling profile.
    Color management does not appear to turn off or disengage within any given print driver.
    When selecting Color Matching, both ColorSync & given printer are active, both should be ghosted out.
    After printing one image/sheet & printing again & selecting Color Matching within the print window both are ghosted out.
    Saving a pre-set does not solve the issue.
    Currently prints are not matching when having PSE12 controlling color.
    what is causing this issue ?  Is it PSE12 ?  Is it the OS ?  WHAT !
    Please help.  THANKS

    This inability to disable color management is within the OS, right ?  Or is it PhotoShop Elements ?
    Yes I do have means of controlling color management from a driver stand point but the attempt here is to turn color management off from the OS & driver to allow the app to control color management.
    Problem is that when printing and setting/selecting settings to allow this, it appears management is getting miss managed.
    And if I set a pre-set within PSE, settings do not hold.
    I do not want ColorSync to control color management.
    I do not want print driver to control color management.
    And settings to not hold from print to print and a pre-set does not appear to hold as well.
    What is the fix for this ? Do not use PSE ?  Do not use MacOS, This does not happen on a WIN based system ?!?

  • WRT160N PS3 MAC Address Filtering

    Does anybody know how to set up the MAC address filtering for a PS3, or if the PS3 even recognizes it?  I find the MAC address for the PS3, enter it into the MAC address allow column and try to connect.  Doesn't work.  Take the MAC Address filter off and bingo back to working.  I am using WPA at the moment, and that is it.  Any suggestions or advice would be much appreciated!  Thanks.
    Solved!
    Go to Solution.

    Once you remove the Mac address...it is working fine...that means the Mac address you are using is probably not correct Mac address.Each and every device has its own Mac address...
    Follow the steps to get the wireless card Mac address for your PS3
    . Power up the PlayStation 3 without any disc in the drive.
    2. Once the PlayStation 3 operating system has loaded, select "Settings."
    3. Once you are in "Settings" select "Network Settings."
    4. When the "Network Settings" list appears, select the first option which is titled "Settings and Connection Status List."
    5. The physical address of the wireless card will be listed under "MAC Address." Write this number down...(this is Mac address).
    Now login into the setup page of your router and try this Mac address. 

Maybe you are looking for