Network timouts

I have a location that randomly drops network packets.. Our Network crew says there is nothing wrong, but when running a continuous ping you can see it randomly drops a packet..
OBIEE 11.1.1.6.2 BP1 does not like this.. when on the BI web page, some computers error, some load text but not graphics, some just load half the page.
is there anyway I can tweak a keepalive or timeout setting so the pages retry after the packet loss and complete loading the full page.
browsers are IE8, (have tried http compression/cache.. same issue)
Server is Windows 2008 R2
Thanks..

this seems to have fixed it.. and made IE much faster..
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Internet Explorer\MAIN\FeatureControl\FEATURE_MAXCONNECTIONSPER1_0SERVER]
"iexplore.exe"=dword:0000000a
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Internet Explorer\MAIN\FeatureControl\FEATURE_MAXCONNECTIONSPERSERVER]
"iexplore.exe"=dword:0000000a
[HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Internet Settings]
"MaxConnectionsPerServer"=dword:00000032
"MaxConnectionsPer1_0Server"=dword:00000032
"KeepAliveTimeout"=dword:0002bf20
"ReceiveTimeout"=dword:0002bf20
"ServerInfoTimeout"=dword:0002bf20

Similar Messages

QMASTER hints 4 usual trouble (QM NOT running/CLUSTEREd nodes/Networks etc

All, I just posted this with some hints & workaround with very common issues people have on this forum and keep asking concerning the use of APPLE QMASTER with FCP, SHAKE, COMPRESSOR and MOTION. I've had many over the last 2 years and see them coming up frequently.
Perhaps these symptoms are fixed in FCS2 at MAY 2007 (now). However if not here's some ROTS that i used for FCP to compressor via QMASTER cluster for example. NO special order but might help someone get around the stuff with QMASTER V2.3, FCP V5.1.4, compressor.app V2.3
I saw the latest QMASTER UI and usage at NAB2007 and it looked a little more solid with some "EASY SETUP" stuff. I hope it has been reworked underneath.. I guess I will know soon if it has.
For most FCP/COMPRESSOR, SHAKE. MOTION and COMPRESSOR:
• provide access from ALL nodes to ALL the source and target objects (files) on their VOLUMES. Simply MOUNT those volumes through the APPLE file system (via NFS) using +k (cmd+k) or finder/go/connect to server. OR using an SSAFS such as XSAN™ where the file systems are all shared over FC not the network. YOu will notice the CPU's going very busy for a small while. THhis is the APPLE FILE SYSTEM task,,, I guess it's doing 'spotlight stuff". This goes away after a few minutes.
• set the COMPRESSOR preferences for "CLUSTER OPTIONS" to "Never copy source to Cluster". This means that all nodes can access your source and target objects (files) over NFS (as above). Failure to to this means LENGTHY times to COPY material back an forth, in some cases undermining the pleasure gained from initially using clustering (reduced job times)
• DONT mix the PHYSICAL or LOGICAL networks in your local cluster. I dont know why but I could never get this to work. Physical mean stick with eother ETHERNET or FIREWIRE or your other (airport etc whic will be generally way to slow and useless), Logical measn leepin all nodes on the SAME subnet. You can do this siply by setting theis up in the system preferences/QMASTER/advanced tab under "Use Network Interfaces". In my currnet QUAd I set this to use BUILT IN ETHERNET1 and in the MPBDC's I set this to their BUILTIN ETHERNET.
• LOGICAL NETWORKS (Subnet): simply HARDCODE an IP address on the ETHERNET (for eample) for your cluster nodes andthe service controller. FOr eample 3.1.1.x .... it will all connect fine.
• Physical Networks: As above (1) DONT MIX firewire (IPoFW) and Ethernet(IPoE). (2) if more than extra service node USE A HUB or SWITCH. I went and bought a 10 port GbE HUB for about $HK400 (€40) and it worked fine. I was NEVER able to get a stable system of QMASTER mixing FW and ETHERNET. (3) fwiw using IP of FW caused me a LOAD of DISK errors and timouts (I/O errors) on thosse DISKs that were FW400 (al gone now) but it showed this was not stable overall
• for the cluster controller node MAKE SURE you set the CLUSTER STORAGE (system preferences/QMASTER/shared cluster storage) for the CLUSTER CONTROLLER NODE IS ON A SHARED volume (See above). This seems essential for SHAKE to work. (if not check the Qmaster errors in the console.app [see below] ). IF you have an SSAFS like XSAN™ then just add this cluster storage on a share file path. NOte that QMASTER does not permit the cluster storage to be on a NETWORK NODE for some reason. So in short just MOUNT the volume where the SHARED CLUSTER file is maintained for the CLUSTER controller.
• FCP - avoid EXPORT to COMPRESSOR from the TIMELINE - it never seems to work properly (see later). Instead EXPORT FROM SEQUENCE in the BROWSER - consistent results
• FCP - "media missing " messages on EXPORT to COMPRESSOR.. seems a defect in FCP 5.1 when you EXPORT using a sequence that is NOT in the "root" or primary trry in the FCP PROJECT BROWSER. Simply if you have browser/bin A contains(Bin B (contains Bin C (contains sequence X))) this will FAIL (wont work) for "EXPORT TO COMPRESSOR" if you use EXPORT to COMPRESSOR in a FCP browser PANE that is separately OPEN. To get around this, simply OPEN/EXPOSE the triangles/trees in the BROWSER PANE for the PROJECT and select the SEQUENCE you want and "EXPORT to COMPRESSOR" from there. This has been documented in a few places in this forum I think.
• FCP -> COMPRESSOR -> .M2V (for DVDSP3): some things here. EXPORTING from an FCP SEQUENCE with CHAPTER MARKERS to an MPEG2 .M2V encoding USING A CLUSTER causes errors in the placement of the chapter makers when it is imported to DVDSP3. In fact CONSISTENTLY, ALL the chapter markers are all PLACED AT THE END of the TRACK in DVD SP# - somewhat useless. This seems to happen ALSO when the source is an FCP reference movie, although inconsistent. A simple work around if you have the machines is TRUN OF SEGMENTING in the COMPRESSOR ENCODER inspector. let each .M2V transcode run on the same service node. FOr the jobs at hand just set up a CLUSTER and controller for each machine and then SELECT the cluster (myclusterA, hisclusterb, herclusterc) for each transcode job.. anyway for me.. the time spent resolving all this I could have TRANSCODED all this on my QUAD and it would all have ben done by sooner! (LOL)
• CONSOLE logs: IF QMASTER fails, I would suggest your fist port of diagnosis should be /Library/Logs/Qmaster in there you will see (on the controller node) compressor.log, jobcontroller.com.apple.qmaster.cluster.admin.log, and lots of others including service controller.com.apple.qmaster.executorX.log (for each cpu/core and node) andd qmasterca.log. All these are worth a look and for me helped me solve 90% of my qmaster errors and failures.
• MOTION 3 - fwiw.. EXPORT USING COMPRESSOR to a CLUSTER seems to fail EVERY TIME.. seems MOTION is writing stuff out to a /var/spool/qmaster
TROUBLESHOOTING QMASTER: IF QMASTER seems buggered up (hosed), then follow these steps PRIOR to restarting you machines.
go read the TROUBLE SHOOTING in the published APPLE docs for COMPRESSOR, SHAKE and "SET UP FOR DISTRIBUTED PROCESSING" and serach these forums CAREFULLY.. the answer is usually there somewhere.
ELSE THEN,, try these steps....
You'll feel that QMASTER is in trouble when you
• see that the QMASTER ICON at the top of the screen says 'NO SERVICES" even though that node is started and
• that the APPLE QMASTER ADMINSTRATOR is VERY SLOW after an 'APPLY" (like minutes with SPINNING BEACHBALL) or it WONT LET YOU DELETE a cluster or you see 'undefined' nodes in your cluster (meaning that one was shut down or had a network failure)..... all this means it's going to get worse and worse. SO DONT submit any more work to QAMSTER... best count you gains and follow this list next.
(a) in COMPRESSOR.app / RESET BACKGROUND PROCESSES (its under the COMPRESSOR name list box) see if things get kick started but you will lose all the work that has been done up to that point for COMPRESSOR.app
b) if no OK, then on EACH node in that cluster, STOP the QMASTER (system preferences/QMASTER/setup [set 0 minutes in the prompt and OK). Then when STOPPED, RESET the shared services my licking OPTION+CLICK on the "START" button to reveal the "RESET SERVICES". Then click "START" on each node to start the services. This has the actin of REMOVING or in the case where the CLUSTER CONTROLLER node is "RESET" f terminating the cluster that's under its control. IF so Simply go to APPLE QMASTER ADMINISTRATOR and REDFINE it. Go restart you cluster.
c) if step (b) is no help, consult the QMASTER logs in /Library/Logs/Qmaster (using the cosole.app) for any FILE MISSING or FILE not found or FILE ERROR . Look carefully for the NODENAME (the machine_name.local) where the error may have occured. Sometimes it's very chatty. Others it is not. ALso look in the BATCH MONITOR OUTPUT for errors messages. Often these are NEVER written (or I cant find them) in the /var/logs... try and resolve any issues you can see (mostly VOLUME or FILE path issues from my experience)
(d) if still no joy then - try removing all the 'dead' cluster files from /var/tmp/qmaster , /var/sppol/qmaster and also the file directory that you specified above for the controller to share the clustering. FOR shake issues, go do the same (note also where the shake shared cluster file path is - it can be also specified in the RENDER FILEOUT nodes prompt).
e) if all this WONT help you, its time to get the BIG hammer out. Simply, STOP all nodes of not stopped. (if status/mode is "STOPPING" then it [QMASTER] is truly buggered). DISMOUNT the network volumes you had mounted. and RESTART ALL YOUR NODES. Tis has the affect of RESTARTING all the QMASTERD tasks. YEs sure you can go in and SUDO restart them but it is dodgy at best because they never seem to terminate cleanly (Kill -9 etc) or FORCE QUIT.... is what one ends up doing and then STILL having to restart.
f) after restart perform steps from (B) again and it will be usually (but not always) right after that
LAstly - here's some posts I have made that may help others for QMASTER 2.3 .. and not for the NEW QMASTER as at MAy 2007...
Topic "qmasterd not running" - how this happened and what we did to fix it. - http://discussions.apple.com/message.jspa?messageID=4168064#4168064
Topic: IP over Firewire AND Ethernet connected cluster? http://discussions.apple.com/message.jspa?messageID=4171772#4171772
LAstly spend some DEDICATED time to using OBJECTIVE keywords to search the FINAL CUT PRO, SHAKE, COMPRESSOR , MOTION and QMASTER forums
hope thats helps.
G5 QUAD 8GB ram w/3.5TB + 2 x 15in MBPCore Mac OS X (10.4.9) FCS1, SHAKE 4.1

Warwick,
Thanks for joining the forum and for doing all this work and posting your results for our benefit.
As FCP2 arrives in our shop, we will try once again to make sense of it and to see if we can boost our efficiencies in rendering big projects and getting Compressor to embrace five or six idle Macs.
Nonetheless, I am still in "Major Disbelief Mode" that Apple has done so little to make this software actually useful.
bogiesan

Unable to check for available downloads. The network connection timed out.

I downloaded iTunes 10.1.2 last week, and attempted to upgrade some music to iTunes Plus. I'm showing 35 items in my download queue, but when I attempt to download I get a message "Unable to check for available downloads. Network connection timed out."
I e-mailed Apple Tech Support multiple times, and received their standard list of links for things to try. So far I have reinstalled iTunes, turned off my Norton Firewall, checked the program rules settings, flushed the dns cache, and unchecked the "allow simultaneous downloads" box. Still no luck.
Apple's last e-mail requested I send them my account info so they could reset my password, and check my system. I'm still waiting for that to happen.
I'd appreciate any user suggestions for this problem.

Fundamentally it is an apple itunes server issue - if you have a lot of downloads the "check for downloads" request can take longer than the default windows internet connection timeout setting - which is 30 seconds on more recent versions of windows.
You can work around it though - without requiring apple to "segment" your download list, by adding a windows registry setting.
Apple re-enabled my downloads after I was burgled and then I was stuck - my "check for downloads" was always timing out - and the support guy had no clue - so I went digging, and found a a microsoft article here http://support.microsoft.com/kb/181050 which tells you how to change change that default timout value by adding a registry setting. Besides adding the ReceiveTimeout setting detailed on that page - I also changed the KeepAliveTimeout - just in case.
HKEYCURRENTUSER\SOFTWARE\Microsoft\Windows\CurrentVersion\Internet Settings\ReceiveTimeout
which I set to 180000 milliseconds (3 mins)
HKEYCURRENTUSER\SOFTWARE\Microsoft\Windows\CurrentVersion\Internet Settings\KeepAliveTimeout
which I set to 181000 milliseconds (3 mins and 1 second)
Use regedit to make the change - both settings are DWORDS with decimal values. You'll need to restart your PC to apply the change.
After the change and restart and one initial failed attempt the request for downloads worked - when the apple itunes server responded after 2 minutes !!

Any kind of bandwith limiting or priority for specific network services ?

I tried IPQoS to limit the bandwith for a ftp-service. This is very well documented in the IPQoS Administration Guide, but it seems to have no effect at all in my lan. The ftp-transfer still consumes all
available bandwith and any other interactive traffic like ssh is slow as hell. I think this is due to the fact that i do not have a diffserv capable router. Is it correct that IPQoS in Solaris 9 only marks packages but don't do anything else ?
My kstat output says:
"kstat -m tokenmt"
module: tokenmt instance: 10
name: tokenmt statistics class: meterftp
crtime 171043.6888275
epackets 0
green_bits 369888
green_packets 196
red_bits 205079496
red_packets 18160
snaptime 174628.7017885
yellow_bits 0
yellow_packets 0
Nearly all packets are marked red and the target for red packets is markAF31 with dscp_map{0-63:26}.
Strange to see that "kstat -m dscpmk" shows no results at all. This is possible a bug or not well
documented in the IPQoS Administration Guide.
Is there any (other) way to priorize interactive traffic or limit/shape the bandwith for specific services without additional Hardware in my network ?

You may have already resolved your problem, but here is what I've been using -- I'm just recently (like two days ago) trying IPQoS.
As you can see from my code I really restricted bandwith so I could see the reaction, and tested with a specific machine so it wouldn't mess with other stuff. Turn on ftp hash and watch it crawl. I've only tested outgoing so far, but will also test incoming.
We are not using DiffServ on our routers, so I just drop 'red' packets. I'm using yellow just to play and get stats.
Am looking for tools to read the flowacct data when I came across your post.
good luck!
fmt_version 1.0
# TEST configuration
# Monitor and gather ftp statistics from pilasvp101 (only)
# this host: ssrv194bw (163.241.195.249)
# this host: pilasrp101 (163.241.205.147)
# remote hosts: pilasvp101 (163.241.195.240)
action {
module ipgpc
name ipgpc.classify
params {
global_stats TRUE
class {
name ftp_traffic
enable_stats TRUE
next_action meter_ftp
filter {
name ftp_in
sport ftp
saddr 163.241.195.240
direction LOCAL_IN
ip_version V4
class ftp_traffic
filter {
name ftp_data_in
sport ftp-data
saddr 163.241.195.240
direction LOCAL_IN
ip_version V4
class ftp_traffic
filter {
name ftp_out
dport ftp
daddr 163.241.195.240
direction LOCAL_OUT
ip_version V4
class ftp_traffic
filter {
name ftp_data_out
dport ftp-data
daddr 163.241.195.240
direction LOCAL_OUT
ip_version V4
class ftp_traffic
# 10 Mbps, or 10000000 bits per second.
# 100 Mbps, or 100000000 bits per second.
# 1000 Mbps, or 1000000000 bits per second.
# USED BELOW:
# committed_rate - 100000 bits per second = 0.10 Mbps.
# committed_burst - 100000 bits per second = 0.10 Mbps.
# peak_rate - 150000 bits per second = 0.15 Mbps.
# peak_burst - 150000 bits per second = 0.15 Mbps.
# committed_rate - allowable transmission rate
# committed_burst - allowable burst size. Defines how many outgoing packets
# of a particular class can pass onto the network at the
# committed rate.
# peak_rate - peak rate in bits per second
# peak_burst - peak or excess burst size in bits. The peak burst parameter
# grants to a traffic class a peak-burst size that exceeds
# the committed rate.
# color_aware - turns on color-aware mode for tokenmt, which expects the
# bits to have already been modified for DSCP
# color_map - defines an integer array that maps DSCP values to
# green, yellow, or red.
# red_action - action to take when traffic flow exceeds peak rate
# yellow_action - the packet causes the flow to exceed its committed_rate
# but not its peak rate (committed_burst). This must be used
# if 'peak_rate' is defined.
# green_action - action to take for conforming traffic flow
# global_stats - enable metering stats for the class
action {
module tokenmt
name meter_ftp
params {
global_stats TRUE
committed_rate 100000
committed_burst 100000
peak_rate 150000
peak_burst 150000
red_action_name red_accounting
yellow_action_name yellow_accounting
green_action_name green_accounting
color_aware FALSE
# timer - scanning interval in milliseconds (default 15 seconds)
# timout - a flow "times-out" when its packets are no longer seen
# by the IPQoS system in milliseconds (default 60 seconds)
# max_limit - maximum number of entries a flow table can contain
action {
module flowacct
name red_accounting
params {
global_stats TRUE
timer 10000
timeout 10000
max_limit 2048
next_action drop
action {
module flowacct
name yellow_accounting
params {
global_stats TRUE
timer 10000
timeout 10000
max_limit 2048
next_action continue
action {
module flowacct
name green_accounting
params {
global_stats TRUE
timer 10000
timeout 10000
max_limit 2048
next_action continue
}

IMac not connecting to wifi on startup/wakeup with only one preferred network

New (June 2012) imac. When it wakes from sleep/powers up, it searches for the only network that i have under preferred - can't find it. I open network prefs. Occasionally there is also a connection timout in there.... It says the computer has a self assigned IP. I turn Wifi off. On again. It (usually) connects.
I know a million other people have variations on this problem. But most of the recs involve clearing known networks. This computer has only ever connected to one and it's the only one on the list. ANy thoughts?
Recently upgraded to 10.8 but was having this issue with 10.7.4 out of the box.
Phones/laptops connect to same network with no issue.

Hi, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
Click OK.
Also, turn off IPv6:
System Preferences » Network » AirPort » TCP/IP tab » Configure IPv6
Or whatever Interface you use.

WLC 2504 sudden network instability

Hello,
we're running a WLC 2504 with two SSIDs on it. It is connected to to a small PoE switch. Standard untagged vlan. A handfull APs connected to it. No DHCP, the APs have all static IP addresses.
All of a sudden we're having a number of issues with the network connection:
APs restarting
The APs restart every now and then reporting that their IP is being used by another device. Looking through the logs there are two MAC addresses that are reported as using the APs IP address. These two MAC addresses have unknown vendor IDs.
Warning: AP with Base Radio MAC f8:72:ea:7c:9d:e3 has found its IP Address 0.2.146.0 being used by a machine with MAC
Address 04:c6:f8:40:00:00 (The other mac that is reported is 04:cc:90:40:00:00)
AP 'AP5', MAC: 0c:68:03:dd:1b:80 disassociated previously due to Link Failure. Uptime: 4 days, 00 h 48 m 50 s . Reason: Capwap WTP Event request.
So: There are two MACs that use the IP addresses of 7 APs?!?! And there is no vendor to be found for these MACs?
Ping timouts on the webGUI and CLI
I have a ping running on the IP for managing the device. This is running fine for ages. As soon as I connect via webGUI or CLI I lose packets. Get timeouts etc. some packets get through some don't. More of the latter. So ping is fine but any other traffic seems to be impacted heavily.
What we have done for troubleshooting
Checked duplex/speed settings of the interfaces. Everything ok.
Connected to another switchport. Same.
Changed the IP address of the management port. Same.
Swapped places with a laptop with the same IP address --> Worked fine.
Plugged in a completely new device, installed the latest firmware (7.6) and uploaded the config from the other one. Same.
Restarted the default gateway for the subnet the controler is on.
So now we're at the end of our knowledge. It seems to be a non-physical network issue, but we're a small team and no one has changed anything they say :-/
Any ideas what we could check next?
Kat

Hello,
thanks for your suggestions. It's hard to find those two MAC addresses. As they seem to be virtual I cannot get a hint from the vendor ID. A show mac-address table on the switch the WLC is connected to doesn't show those two
I found an error in the WLC AP config. AP1 had the same IP as AP5 and a wrong netmask. I changed that. Unfortunately that doesn't solve our problem.
Here are some more messages from the WLC's log:
AP 'AP3', MAC: 0c:68:03:dd:34:00 disassociated previously due to Link Failure. Uptime: 4 days, 15 h 04 m 15 s . Reason: Capwap WTP Event request.
AP Disassociated. Base Radio MAC:0c:68:03:dd:34:00
AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:0c:68:03:dd:34:00 Cause=Heartbeat Timeout Status:NA
AP 'AP3', MAC: 0c:68:03:dd:34:00 disassociated previously due to Link Failure. Uptime: 4 days, 15 h 00 m 45 s . Reason: Capwap WTP Event request.
RF Manager updated TxPower for Base Radio MAC: 0c:68:03:dd:34:00 and slotNo: 0. New Tx Power is: 2
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:0c:68:03:dd:16:e0 Cause=Max Retransmission Status:NA
IDS Signature attack detected. Signature Type: Standard, Name: Deauth flood, Description: Deauthentication flood, Track: per-signature, Detecting AP Name: AP7, Radio Type: 802.11b/g, Preced: 9, Hits: 500, Channel: 6, srcMac: C2:9F:DB:21:47:60
This is the sh run-config of our WLC including one AP:
>show run-config
System Inventory
NAME: "Chassis"    , DESCR: "Cisco 2500 Series Wireless LAN Controller"
PID: AIR-CT2504-K9, VID: V01, SN: PSZ17381EPZ
Burned-in MAC Address............................ 50:17:FF:27:12:80
Maximum number of APs supported.................. 15
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.18
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... UK-BRI-WFAPC
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 172.17.128.12
Last Reset....................................... Power on reset
System Up Time................................... 4 days 0 hrs 46 mins 6 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... GB - United Kingdom
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +20 C
External Temperature............................. +25 C
Fan Status....................................... 4000 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 3
Number of Active Clients......................... 6
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 50:17:FF:27:12:80
Maximum number of APs supported.................. 15
AP Bundle Information
Primary AP Image    Size
ap1g2            9568
ap3g1            11288
ap3g2            11196
ap801            7164
ap802            8568
c1130            5072
c1140            9416
c1250            6944
c1520            8044
c602i            3736
Secondary AP Image    Size
ap3g1            5792
ap801            5192
ap802            5232
c1100            3084
c1130            4964
c1140            4992
c1200            3364
c1240            4812
c1250            5504
c1310            3136
c1520            6404
c3201            4324
c602i            3716
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
     case-check ...........Enabled
     consecutive-check ....Enabled
     default-check .......Enabled
     username-check ......Enabled
Network Information
RF-Network Name............................. RFGROUP
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Disable
Secure Web Mode RC4 Cipher Preference....... Disable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Multicast   Address : 0.0.0.0
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
MLD snooping................................ Disabled
MLD timeout................................. 60 seconds
MLD query interval.......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Disable
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth CMCC Support ...................... Disabled
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Web Auth Captive-Bypass   .................. Disable
Web Auth Secure Web ....................... Enable
Fast SSID Change ........................... Disabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
CCX-lite status ............................ Disable
oeap-600 dual-rlan-ports ................... Disable
oeap-600 local-network ..................... Enable
mDNS snooping............................... Disabled
mDNS Query Interval......................... 15 minutes
Port Summary
           STP   Admin   Physical   Physical   Link   Link
Pr Type   Stat   Mode     Mode      Status   Status Trap     POE
1 Normal Forw Enable Auto       1000 Full Up     Enable N/A
2 Normal Forw Enable Auto       100 Full   Up     Enable N/A
3 Normal Forw Enable Auto       1000 Full Up     Enable Enable (Power Off)
4 Normal Disa Enable Auto       Auto       Down   Enable Enable (Power Off)
AP Summary
Number of APs.................................... 7
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name             Slots AP Model              Ethernet MAC       Location          Port Country Priority
AP7                  2     AIR-CAP1602I-E-K9     f8:72:ea:e4:9a:81 default location 1        GB       1
AP1                  2     AIR-CAP1602I-E-K9     f8:72:ea:7c:9d:e3 default location 1        GB       1
AP3                  2     AIR-CAP1602I-E-K9     f8:72:ea:e4:9c:57 default location 1        GB       1
AP6                  2     AIR-CAP1602I-E-K9     f8:72:ea:e4:9a:90 default location 1        GB       1
AP2                  2     AIR-CAP1602I-E-K9     f8:72:ea:7c:9b:63 default location 1        GB       1
AP4                  2     AIR-CAP1602I-E-K9     f8:72:ea:e4:9a:9b default location 1        GB       1
AP5                  2     AIR-CAP1602I-E-K9     f8:72:ea:e4:9a:cb default location 1        GB       1
AP Tcp-Mss-Adjust Info
AP Name              TCP State MSS Size
AP7                  disabled   -
AP1                  disabled   -
AP3                  disabled   -
AP6                  disabled   -
AP2                  disabled   -
AP4                  disabled   -
AP5                  disabled   -
AP Location
Total Number of AP Groups........................ 0
Site Name........................................ default-group
Site Description.................................
NAS-identifier................................... UK-BRI-WFAPC
AP Operating Class............................... Not-configured
RF Profile
2.4 GHz band.....................................
5 GHz band.......................................
WLAN ID          Interface          Network Admission Control          Radio Policy
1               corporate            Disabled                          None
2               dirtynetwork         Disabled                          None
3               dirtynetwork         Disabled                          None
AP Name             Slots AP Model             Ethernet MAC       Location          Port Country Priority
AP7                  2     AIR-CAP1602I-E-K9    f8:72:ea:e4:9a:81 default location 1     GB       1
AP1                  2     AIR-CAP1602I-E-K9    f8:72:ea:7c:9d:e3 default location 1     GB       1
AP3                  2     AIR-CAP1602I-E-K9    f8:72:ea:e4:9c:57 default location 1     GB       1
AP6                  2     AIR-CAP1602I-E-K9    f8:72:ea:e4:9a:90 default location 1     GB       1
AP2                  2     AIR-CAP1602I-E-K9    f8:72:ea:7c:9b:63 default location 1     GB       1
AP4                  2     AIR-CAP1602I-E-K9    f8:
RF Profile
Number of RF Profiles............................ 0
Out Of Box State................................. Disabled
RF Profile Name                    Band     Description                         11n-client-only
AP Config
Cisco AP Identifier.............................. 15
Cisco AP Name.................................... AP7
Country code..................................... GB - United Kingdom
Regulatory Domain allowed by Country............. 802.11bg:-E     802.11a:-E
AP Country code..................
................ GB - United Kingdom
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... f8:72:ea:e4:9a:81
IP Address Configuration......................... Static IP assigned
IP Address....................................... 172.17.128.24
IP NetMask....................................... 255.255.128.0
Gateway IP Addr.................................. 172.17.128.1
Domain...............
Name Server......................................
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Floor Label............................. 0
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ....
............................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ..
....................... kern
S/W Version .................................... 7.4.110.0
Boot Version ................................... 15.2.2.0
Mini IOS Version ................................ 7.4.1.37
Stats Reporting Period .......................... 180
Stats Collection Mode ........................... normal
LED State........................................
Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-CAP1602I-E-K9
AP Image...............................
.......... C1600-K9W8-M
IOS Version...................................... 15.2(2)JB2$
Reset Button..................................... Enabled
AP Serial Number................................. FGL1725W7F7
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system loggi
ng host..................... 255.255.255.255
AP Up Time....................................... 3 days, 23 h 26 m 50 s
AP LWAPP Up Time................................. 0 days, 00 h 14 m 12 s
Join Date and Time............................... Tue Jan 28 18:11:43 2014
Join Taken Time.................................. 0 days, 00 h 11 m 41 s
Attributes for Slot 0
    Radio Type................................... RADIO_TYPE_80211n-2.4
    Administrative State ........................ ADMIN_ENABLED
    Operation State ............................. UP
    Radio Role .................................. ACCESS
    Radio Mode .................................. Local
    CellId ...................................... 0
    Station Configuration
      Configuration ............................. AU
TOMATIC
      Number Of WLANs ........................... 3
      Medium Occupancy Limit .................... 100
      CFP Period ................................ 4
      CFP MaxDuration ........................... 60
      BSSID ..................................... 0c:68:03:dd:16:e0
      Operation Rate Set
        1000 Kilo Bits........................... MANDATORY
        2000 Kilo Bits........................... MANDATORY
        5500 Kilo Bits........................... MANDATORY
        11000 Kilo Bits.......................... MANDATORY
        6000 Kilo Bits........................... SUPPORTED
        9000 Kilo Bits........................... SUPPORTED
        12000 Kilo Bits.......................... SUPPORTED
        18000 Kilo Bits.......................... SUPPORTED
        24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
        48000 Kilo Bits.......................... SUPPORTED
        54000 Kilo Bits.......................... SUPPORTED
      MCS Set
        MCS 0.................................... SUPPORTED
        MCS 1.................................... SUPPORTED
        MCS 2.................................... SUPPORTED
        MCS 3.................................... SUPPORTED
        MCS 4.................................... SUPPORTED
        MCS 5.................................... SUPPORTED
        MCS 6.................................... SUPPORTED
        MCS 7.................................... SUPPORTED
        MCS 8.................................... SUPPORTED
        MCS 9.................................... SUPPORTED
        MCS 10................................... SUPPORTED
        MCS 11................................... SUPPORTED
        MCS 12..
................................. SUPPORTED
        MCS 13................................... SUPPORTED
        MCS 14................................... SUPPORTED
        MCS 15................................... SUPPORTED
        MCS 16................................... DISABLED
        MCS 17................................... DISABLED
        MCS 18................................... DISABLED
        MCS 19................................... DISABLED
        MCS 20................................... DISABLED
        MCS 21................................... DISABLED
        MCS 22................................... DISABLED
        MCS 23................................... DISABLED
      Beacon Period ............................. 100
      Fragmentation Threshold ................... 2346
      Multi Domain Capability Implemented ....... TRUE
      Multi Domain Capability Enabled ........... TRUE
      Country String ............................ GB
    Multi Domain Capability
      Configuration ............................. AUTOMATIC
      First Chan Num ............................ 1
      Number Of Channels ........................ 13
    MAC Operation Parameters
      Configuration ............................. AUTOMATIC
      Fragmentation Threshold ................... 2346
      Packet Retry Limit ........................ 64
    Tx Power
      Num Of Supported Power Levels ............. 4
      Tx Power Level 1 .......................... 16 dBm
      Tx Power Level 2 .......................... 13 dBm
      Tx Power Level 3 .......................... 10 dBm
      Tx Power Level 4 .......................... 7 dBm
      Tx Power Configuration .................... AUTOMATIC
      Current Tx Power Level .................... 3
      Tx Power Assigned By ...................... DTPC
    Phy OFDM parameters
      Configuration ............................. AUTOMATIC
      Current Channel ........................... 6
      Channel Assigned By ....................... DCA
      Extension Channel ......................... NONE
      Channel Width.............................. 20 Mhz
      Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11,12,
        ......................................... 13
      TI Threshold .............................. -50
      Legacy Tx Beamforming Configuration ....... CUSTOMIZED
      Legacy Tx Beamforming ..................... ENABLED
      Antenna Type............................... INTERNAL_ANTENNA
      Internal Antenna Gain (in .5 dBi units).... 8
      Diversity.................................. DIVERSITY_ENABLED
      802.11n Antennas
         A....................................... ENABLED
         B....................................... ENABLED
         C....................................... ENABLED
    Performance Profile Parameters
      Configuration ............................. AUTOMATIC
      Interference threshold..................... 10 %
      Noise threshold............................ -70 dBm
      RF utilization threshold................... 80 %
      Data-rate threshold........................ 1000000 bps
      Client threshold........................... 12 clients
      Coverage SNR threshold..................... 12 dB
      Coverage exception level................... 25 %
      Client minimum exception level............. 3 clients
    Rogue Containment Information
    Containment Count............................
    CleanAir Management Information
        CleanAir Capable......................... No
    Radio Extended Configurations
      Beacon period.............................. 100 milliseconds
      Beacon range............................... AUTO
      Multicast buffer........................... AUTO
      Multicast data-rate........................ AUTO
      RX SOP threshold........................... AUTO
      CCA threshold.............................. AUTO

Small office network

Hi there,
I want to install/move our office over the weekend and have some lose ends, which i hope can be answered in this forum.
First, let me start off mentioning what i intend to do:
we have three (airport enabled) iMacs sitting in the middle of our office.
At the far end of the office we have the DSL modem, a Gigabit Ethernet Switch, the airport extreme station.
At the other end of the office, I have a HP Color LaserJet (networkable) and a PowerMac G5 1.8GhZ DP (has an airport card installed).
I would like to have the three iMacs connected to the Internet, the Printer and the G5 PowerMac (which will serve as a server). I go about that by connecting the Modem with a jumper cable to the Gigabit switch, as well as the Ethernet cable (regular ONE-WAY) from the printer and the G5 into the Gigabit Switch, I assume. Then I lead one Ethernet Cable from the Gigabit Switch into the airport station, so that an (optional) laptop could access all of teh attached goodies.
Eeventhough the iMacs are airport enabled, I would rather have the option of having them hardwired as well (for speed reasons). I just plug those ethernet cables inside the Gigabit Switch as well?
Thats the technical part.
Now a question about the PowerMac G5. Everyone on the network needs to access files which I will store on the G5, such as photo library and some word and xls documents. Can i just make everything shareable?
Thank you in advance for any suggestions/input you might have.
G5 imac, powermac, etc Mac OS X (10.4.6)

It sounds like you have it right - if you're using wired ethernet connections just connect everything back to the switch.
For the base station, make sure it's running in bridge rather than route mode - using AirPort Admin Utility, turn off the 'distribute IP addresses' option.
As for the file sharing, I wouldn't share the entire drive, but designate one folder (or folders) as being shared. If this is running Mac OS X client (vs. Server) get a copy of SharePoints which will make it easy to select which folders are available for sharing.
Unless you're also running as a directory server you'll also need to make sure that the G5 has an account for everyone that is going to log onto it to access the shared folders. You could use one common account, but that's not recommended.

Cannot send email from outlook 2011 (Mac) on public networks but can send via Mac Mail

I cannot send mail with Outlook from anywhere other than my work or home network, will not work even when accessing 4g with my phone hotspot; very frustrating. I am using Yosemite & Macbook Pro (2012). if i use the Apple Mail everything works fine so I can only assume it is a setting on Outlook?

Update - I now have it working.
am not really sure what exactly fixed it.
I changed a lot of things but my setup now has the following which I think fixed.
outgoing server - p06-smtp.mail.me.com
override default port checked - port now 587
on more options button changed it to "use incoming server info".

Network Cable unplugged

I have BT Total Broadband Anywhere Home Hub 2. I have used it successfully on my desktop pc and wirelessly with my laptop. However I went away for 2 months and was unable to use either (everything was switched off whilst away). On my return the laptop can't connect at all, I just get two grey monitors with a red X and the information 'A Network Cable is unplugged'. I bought a netbook when away and am having the same problem with that now.
On the laptop that worked before, on my Network Connections it is showing as follows:
Local Area Connection 2
Network cable unplugged
Broadcom 440 x 10/100 Integrated Controller
1394 Connection 2
Connected
1394 Net Adapter #2
I have tried connecting to the Hub with an ethernet cable without success and when I run the Hub Manager on the laptop it just says it can't connect with the hub. When I run the Hub Manager on my desktop it says there is no wireless device detected.
A check on the laptops device manager hardware shows everything as working properly, but when I try the Wireless WLAN configuration utility in Control Panel it tells me there are currently no wireless adapters available and enabled.
I am getting desperate as I cannot sit at the desktop for any length of time and need the laptop, please can anyone help?

chunkleberry wrote:
I have BT Total Broadband Anywhere Home Hub 2. I have used it successfully on my desktop pc and wirelessly with my laptop. However I went away for 2 months and was unable to use either (everything was switched off whilst away). On my return the laptop can't connect at all, I just get two grey monitors with a red X and the information 'A Network Cable is unplugged'. I bought a netbook when away and am having the same problem with that now.
On the laptop that worked before, on my Network Connections it is showing as follows:
Local Area Connection 2
Network cable unplugged
Broadcom 440 x 10/100 Integrated Controller
1394 Connection 2
Connected
1394 Net Adapter #2
I have tried connecting to the Hub with an ethernet cable without success and when I run the Hub Manager on the laptop it just says it can't connect with the hub. When I run the Hub Manager on my desktop it says there is no wireless device detected.
A check on the laptops device manager hardware shows everything as working properly, but when I try the Wireless WLAN configuration utility in Control Panel it tells me there are currently no wireless adapters available and enabled.
I am getting desperate as I cannot sit at the desktop for any length of time and need the laptop, please can anyone help?
Hi, the devices you have mentioned are the 'wired' connections. On most laptops, there are switched you can press to turn on and off wireless, is it posisble this has been done?
You can check to see if 'wireless network' appears by selecting the Start Button, then click on Control Panel and open, you should see 'Network' (doing this by memory) and open that up, you will see Wired Lan and Wireless Lan.
If Wireless Lan is disabled, you can right click on wireless lan and enable it, that should work.
CG
CG Over An Out

AIO Remote wont recognize my network printer deskjet 3050

AIO remote app (IOS) did not recognize my network printer (Deskjet 3050), other apps (printer pro lite) did recognize the printer flawlessly, both the printer and the iphone are in the same network, I can print from my PC and my mac but not from AIO remote app (not even recognize the printer).
Can you help me?

Hello MrCrysis,
With the Printer Pro Lite app working to printer, this is excellent to hear. Although this is not an HP app. So to explain as to why the AiO Remote app is not recognizing your printer, and not being able to scan. Your printer does not have AirPrint capabilities according to the 'HP Deskjet 3050 (J610) and 3050A (J611) All-in-One Printer Series Product Specifications'. AirPrint is a requirement for the HP AiO Remote app to work, and because the printer does not have AirPrint the app can not see the printer.
Regards .
I worked on behalf of HP

AIO Remote app cant find HP 3050 printer on my network

Well thats my problem, I tried Fing and it sees the printer, tried ePrint free and it prints like a charm, but AIO does not even see my printer on my network (and yes my printer is in the same network as my mobile device is) I can print from my PC (windows 7) and my MAC (leopard) but I cant print from my iphone 4 using your app. I did the direct connect and it works but I need the network connect instead.
Am I missing something here?
THX for supporting me.

Hi MrCrysis,
Your question has been answered on http://h30434.www3.hp.com/t5/ePrint-Print-Apps-Mobile-Printing-and-ePrintCenter/AIO-Remote-wont-reco...
Regards
I worked on behalf of HP

AIO Remote app cant find HP 7150 aio printer on my wifi network, on Windows Phone 8

HI,
Yesterday I install You App AIO Remote on Windows Phone 8. I have connected to wifi HP 7150 aio printer, but phone cant find this printer... I have Lumia 1520 and Lumia 920 smartphones both is connect to this same wifi network like printer, but You app on both Lumias cant find printer, again but no problem is to connect to printer WEB interface from this both Lumias, so wifi network is correct configured.
I have two tablet more in this same wifi network, both with windows 8.1 x64 systems, on this, You Windows 8 modern App AIO Remote find this same printer without problem...
So what is wrong ? printer config ? eprint is on, ipp is on, bonjur is on, ip is static.
Please help Me becease I wait for this app and now i cant use them
Thanx
Peter

Hi Peter,
Welcome to the HP Support Forums. I understand that you are trying to use the new HP AiO Remote app for Windows phones to print to your Photosmart 7150 printer.
The Photosmart 7150 printer only supports USB connectivity, I have include the Photosmart 7150 Printer Specifications for reference. To be able to use the HP AiO Remote app the printer needs to be connected to a wireless network.
If you accidentally typed the incorrect printer model, please let me know which make/model/product number of HP printer that you have. How Do I Find My Model Number or Product Number?
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Google Play on Tablet works on WIFI not Verizon network.

I have an Motorola Ellipsis Tablet. I am unable to use Google Player. When I open the app, I get "Background data disable. Google play store needs background data to be enabled." I hit enable and It asks me to choose either Facebook or Gmail. I choose my email account and it tries to sync and I get the message "Sync is currently experiencing problems. It will be back shortly." Everything works fine when I am on WIFI at home but when I get to work and I'm on the Verizon network it won't work. I can't use Pandora or look at video. Can someone help me figure out why it is not working on the Verizon network? Thanks.

Hi Mollie88,
Oh my! Let's get you back to enjoying your device. Some applications depend upon background data (transferring data when not directly in use). Restricting background data may cause those apps to stop functioning unless a Wi-Fi connection is available. To uncheck Restrict background data in the Google Play application, follow the directions in the link http://vz.to/1f5KM7b .
Thanks,
PamelaF_VZW
Tweet us @vzwsupport

X201 Tablet: Drivers not working for Network controller on Windows 7 Pro x64

Hello,
After downloading and installing all LAN and WLAN drivers for X201 Tablet, I couldn't find one that works on Windows 7 x64.
How can I proceed?
Thank you in advance
Solved!
Go to Solution.

I fixed it by downloading this drivers:
https://downloadcenter.intel.com/download/18713/Network-Adapter-Driver-for-Windows-7-
And after installing them and restarting, searching for them manually from the Device Manager.
Cheers

IPad iOS 8.1 Mail constant network use draining battery

Since updating to iOS 8.1, iPad Mail is rapidly draining my battery. When I go into Mail the network usage indicator (spinning wheel) runs constantly. I left it this way by mistake while traveling and it drained the whole battery with minimal actual usage in one day -- I usually only have to recharge every 2-3 days.
I have checked the battery usage indicator in Settings and it shows that in the last 24 hours Mail used 54% of the battery. I had changed no settings, but went into Mail & Calendar settings and double-checked them, and they were as they had always been. I have three email accounts: Gmail, Verizon, and a company account on an Exchange server. It's the only one that was set to Push, but now I've set it to Fetch like the others and it still continuously accesses the network when I'm in Mail.
This must be a bug of some kind introduced by a recent OS or app update, right? This never happened before, and nothing else has changed in my usage of the iPad or Mail.
One other issue: Mail is not actually fetching new mail when it should. I see new mail show up on Mac Mail hours before it appears on the iPad. Normally email would arrive almost simultaneously on my iPhone and iPad, then a moment later on the Mac. Now the phone is still first, but the iPad lags. The only way I can get the iPad to refresh in real time is to close the app and restart it.
Is anyone else seeing this behavior with the recent update? Any idea how to fix it?

Found a solution at: http://webcamsocialshopper.com/iphone-battery-suddenly-draining-try-this-non-res tore-method
Short version, remove your Exchange account, shut down phone, restart, add the Exchange account back. Problem solved.

Network timouts

Similar Messages

Maybe you are looking for