New hard drive does not get recognized by OS X server 10.6

Xserve disk utility does no see the new HD. It is not HD issue as I have tested drive in other carrier, switched drive in different bays, booted from Xserve 10.6 dvd and 10.6 Server image in our net boot. Drive is not seen by disk utility. Even put in an Apple original (Mac Pro) HD. We have verified that. memory, HDD carrier and HD Bay are not defective.

Thanks John for the reply. I tried different new hard drives as well as a HD from Mac Pro server.I did try drive in different bays. Other 2 drives in the Xserve are recognized in all bays.I even switced HD carrier. Nothing seems to work. I found the following notes in the Xserve manual. I could not fully understand that. May be you can help me understand this.
Xserve (Late 2006) includes three hard drive bays on the front panel. Hard drives come as
modules, known as Apple drive modules (ADMs), attached to carriers; they are removed from or
installed in the Xserve as a unit. ADMs have been available from Apple in various capacities for
all Xserve and Xserve RAID models, and in multiple interface types. Xserve G4 and Xserve RAID
use parallel ATA (PATA) ADMs, and Xserve G5 uses serial ATA (SATA) ADMs. Xserve (Late 2006) can
use SATA ADMs, and ADMs with a new, third interface type known as serial attached SCSI (SAS).
It is important to understand ADM forward compatibility and backward compatibility with older
Xserve models, since some combinations of ADM and Xserve or RAID work properly while other
combinations do not. The following table summarizes this compatibility.
Xserve G4 Xserve RAID Xserve G5 Xserve
(Late 2006)
Xserve (Early
2008)

Similar Messages

  • My new hard drive does not allow me to load programs on my IMac. It doesn't recognize my administrator password.  How can I correct it?

    my new hard drive does not allow me to load programs on my IMac. It doesn't recognize my administrator password.  How can I correct it?

    Wrong forums. Try http://answers.microsoft.com/en-us/mac

  • New Hard Drive Does not exist!

    Hello, 
    I have an HP DV6 -3142 Laptop and recently after owning it for around a year, my hard drive seems to have crashed. When I try to boot up the laptop, it asks me to use system repair to "repair" my problem or start windows normally. Booting normally causes the laptop to be stuck at windos and revert back to booting up again (it's like a closed loop!). If i choose to "repair" I get stuck at a blue screen where the HP system recovery is supposed to help me either reset to factory settings or do a system restore. I also did a hard disk test in the BIOS and got an error 303. I had done a bit of research and from what i heard, It was a hard drive problem. I got a new hard drive (Samsung) and now when I try to install windows 7, It says that there are no devices to load windows 7 onto. In other words, the Hard disk does not exist (also did a test in bios). I tried to reseat the hard drive and reset BIOS, it didn't work. Now, when I try booting the new hard drive, it shows me a message saying "Media test failure: check cable".
    Any ideas on how i could go about fixing this problem?

    Welcome Larg.
    Sorry but it sounds like your new hard drive is DOA.
    If you have a SATA to USB I would hook it up to another computer and  test it that way.
    Or you may try to install it in another computer and see if you can test it that way.
    Sorry.
    REO
    HP Expert Tester "Now testing HP Pavilion 15t i3-4030U Win8.1, 6GB RAM and 750GB HDD"
    Loaner Program”HP Split 13 x2 13r010dx i3-4012Y Win8.1, 4GB RAM and 500GB Hybrid HDD”
    Microsoft Registered Refurbisher
    Registered Microsoft Partner
    Apple Certified Macintosh Technician Certification in progress.

  • Ibook g3 hard drive does not show up after new installation

    I have an older ibook g3. I purchased a 20gb hard drive to replace the dead 10gb hard drive that came with the computer when I bought it new. The installation was fairly easy. After the hard drive was installed and everything was put back together I turned on the computer and loaded the install disk into the cd tray. The new hard drive does not show up in order to install the operating system. What do I need to do in order to get the hard drive to show up?
    Scott

    Hey Scott,
    The new hard drive does not show up in order to install the operating system. What do I need to do in order to get the hard drive to show up?
    When you're in the installer go up to the top menu bar under utilities? or tools? and start up disk utilities. See if you see the hard drive there. If so it might not be formatted correctly so erase it and format it for your install (usually Mac OS Extended (Journaled). That should make it show up.
    Richard

  • I have just installed a new hard drive in my imac intel 20" (2006) and now the hard drive does not show up in the 'select destinations' folder of the install program.

    I have just installed a new hard drive in my imac intel 20" (2006) and upgraded the memory and now the hard drive does not show up in the 'select destinations' folder of the install program. I can see the hard drive in the disk utilities window however it wont let me do anything.
    It is a seagate 1TB SATA II drive however it is displaying it as a 7.3 TB.
    If anyone has any suggestions I would be happy to hear them.
    I have tried to erase and partition and get the same error message each time, 'Input/Output error'.
    I have tried starting the thing with the install disk which is Mac OS X (Tiger?) which came with the computer. No good.
    Anyone?

    Thats correct. I can see it in the list however when I attempt to erase it or partition it it's like it's not being found or recognised and it throws up the input/output error message. I am pretty sure that the sensor it attached correctly and it is a SATA drive. I can see all the infor regarding the drive when disk utility is open and it all looks good but I cant access it or do anything with it. It's taunting me!
    The install disk is in the drive and the install program runs right up to the point where you have to select the location for the install and there is just nothing in the box where you have to select the hard drive icon.
    I have my suspiscions about the drive but any help would be appreciated.

  • New hard drive is not recognized by my MacBook Pro.

    New hard drive is not recognized by my MacBook Pro. The supplier says I need to update my BIOS. True? How do I do that?
    Hard drive: NN2-72-500-SSE Seagate Momentus 7200.4 (ST9500423AS) 500GB Laptop Hard Drive
    Mac OS: Mac OS X Lion 10.7.5

    I went through a similar issue with a Seagate Momentus 750GB HDD/8GB SSD with my late-2011 MBP.  No matter what I tried, the machine would not recognize the drive.
    To test it, I installed the drive in an old ThinkPad, and it worked fine.  Then I tried installing it in my PS3, and the drive worked fine there, too.  It was only the MBP which had issues.
    I don't *think* Macs have a BIOS to update.  But I know my MBP has issues with certain HDD's (including another external which works fine on other Macs and all Windows machines).
    You might be able to find my thread by searching under my username, perhaps something in there will offer a tip.  Otherwise, you might have to go the same route I did: install a WD Scorpio Black instead.  Or upgrade to an SSD.
    Good luck to you-

  • External Hard Drive does not mount

    My 2TB external hard drive does not mount and I cannot get it to.  Have tried turning the hard drive off and then back on.  No response.  Any thoughts as to how I can get it to be recognized?

    You can try doing a SMC reset, if it doesn't work the first time it's totally OK to reset the SMC several times.
    SMC RESET
    Shut down the computer.
    Unplug the computer's power cord and all peripherals.
    Press and hold the power button for 5 seconds.
    Release the power button.
    Attach the computers power cable.
    Press the power button to turn on the computer.
    PRAM RESET
    Shut down the computer.
    Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.

  • External hard drive does not shut down

    Hello, When my mini mac goes to sleep my samsung external hard drive does not shut down or dismount properly. when i wake computer i have a error message stating improperly ejected hard drive. It also does not reconize HD until I disconnect and reconnet??? PLEASE HELP Thank you

    My Mini was doing the same thing until I reset the PRAM. With four external drives. They would stop inadvertently with an "improperly ejected" error. Granted two of the drives went bad (6 and 7 years old) but a brand spanking new Seagate and a 3 year old Hitachi drive doing the same. Haven't seen the error since resetting the PRAM.
    If you don't know how to do that, Reboot while holding the Cmd+Opt+P+R keys until your hear the startup chime three times and then release the keys.

  • HT3275 Time Machine says my external hard drive does not have enough

    Time Machine says my external hard drive does not have enough space for the current backup.  It needs 34 G out of a 250G hard drive.  All that is on the drive is earlier backups.  I recently added memory, which may confuse Time Machine into thinking it is a new computer.  How can I erase old backups and complete this one?

    Walter Goodman wrote:
    Time Machine says my external hard drive does not have enough space for the current backup.  It needs 34 G out of a 250G hard drive.  All that is on the drive is earlier backups.
    See #C4 in Time Machine - Troubleshooting. 
    If that doesn't clear it up, how much data is on your Mac?  If TM is only trying to back-up 34 GB, it should be able to delete old backups to do that (assuming you're running Lion).
    It sounds like your backups may be corrupted.  Try to repair them, per #A5 in Time Machine - Troubleshooting.
    I recently added memory, which may confuse Time Machine into thinking it is a new computer.
    If that's all you did, no.  
    How can I erase old backups and complete this one?
    Just erase the drive per #1 or #2 of Using Disk Utility.

  • Finder & Dock do not work - Mac Hard Drive does not appear on Desktop

    Until yesterday, my powerbook was working properly.
    This morning, I wanted to use it and I had the following problems after login.
    1/ My Mac Hard drive does not appear on my dekstop
    2/ My dock appears but no icon works when I click on them. So, I can't open finder. I have no response.
    3/ Furthermore, my top bar (with clock, login name, Airport icon...) appears but it is frozed.
    I try several solutions as :
    - rebooting in safe mode,
    - rebooting, with in the same time, hold different keys (option, apple, p & R)...
    As of today, no solution works.
    Thanks for your help.

    A.CHAMP wrote:
    Nota: if i used my daugther login (she is not admin), I have the same issues.
    Ok, that's good enough. You may be able to repair this with the 10.5.8 Combo Update This is a fuller install, as opposed to an incremental "delta" update so it should overwrite any files that are damaged or missing. It does not matter if you have applied it before.
    Remember to Verify Disk before update and repair permissions after update from /Applications/Utilities/Disk Utility.
    EDIT:
    I have around 5 Go space left on my Mac
    Also, your getting very low on disk space. Try to copy some of the data off to other media. *Do it before you try applying the combo, you'll need the space.*
    -mj
    Message was edited by: macjack
    Message was edited by: macjack

  • Hard Drive does not have enough space/error message

    Hello: I am new to Mac but have been having trouble with my iMac for a while. I can no longer download my software updates. I have an error message that states "Your hard drive does not have enough space" - 5.7 GB is required.
    I only have a 1 GB machine. What am I doing wrong?
    When I go to my Macintosh HD icon on the desktop, it says at the bottom of that window that I have 495.9 MB available.
    The error message tells me to go to the Startup file to delete items. I go there, but there's only two files. I do have music/photos/but I do not understand what's going on with my computer.
    In addition, it turns itself off often, for no apparent reason. Any ideas?
    Thanks!
    J.Renee

    The error refers to space on your hard drive, not memory. Unless you've mis-typed, if you have only 495.9 MBs free on your hard drive then you are definitely out of space. If you continue operating with so little free space you are risking a catastrophic loss of data.
    To free up space you will either need to delete unneeded personal files or copy some of your bigger files off to an external hard drive then delete them from your internal drive. Alternatively you can replace the internal drive with a larger drive.
    You should maintain no less than 15 GBs or 15% of the hard drive's capacity as free space whichever is greater.
    If you meant to type 495.9 GBs then you may have a corrupted disk directory. Try the following:
    Repairing the Hard Drive and Permissions
    Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger and Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
    If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger, and 4.1 for Leopard) and/or TechTool Pro (4.6.1 for Leopard) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.

  • My backup hard drive does not have enough space for time machine to perform a back up even after erasing entire contents of bu hard drive

    My backup hard drive does not have enough space for time machine to perform a back up even after erasing entire contents of bu hard drive.  The hard drive has been in service for almost two years performing this function with no sign of failure.  How do I adjust time machine perameters?

    The only way to limit the size of the backup is to exclude data from the backup, which you can do in Time Machine preferences.
    If you use multiple browsers, have you tried clearing your browser caches? However, that's just a stop gap if it works. You either need to limit what you backup or get another drive.

  • Running Time Machine for the first time, how that I make sure that some information I have in the external drive does not get erase in the prosess

    Running Time Machine for the first time, how that I make sure that some information I have in the external drive does not get erase in the prosess

    1. Quit iPhoto
    2. Copy the iPhoto Library from your Pictures Folder to the External Disk.
    3. Hold down the option (or alt) key while launching iPhoto. From the resulting menu select 'Choose Library' and navigate to the new location. From that point on this will be the default location of your library.
    4. Test the library and when you're sure all is well, trash the one on your internal HD to free up space.
    Note: This is now your Library. It's not a Back Up, and you need another disk for backing up.
    Regards
    TD

  • Iphone 3GS no battery charging icon, does not show charging, does not get recognized by computer or Itunes.

    Iphone 3GS no battery charging icon, does not show charging, does not get recognized by computer or Itunes, have tried restore mode & DFU mode. Bad battery or port?

    iPhone not appearing in iTunes

  • External hard drive does not show up

    External hard drive does not show up in imovie.

    Hi,
    Welcome to the Discussions.
    The drive's directory is damaged and as you found Disk Utility isn't equipped to repair it. You need Disk Warrior or Tech Tool Pro.
    John

Maybe you are looking for