New to DMVPN - Getting internet from Hub to Spoke

Currently setting up DMVPN Between one hub and spoke. We use all static routing. I successfully created the tunnel and am able to get into our internal network from the spoke lan. However, I am unable to get any internet access.
Here's the static routing on the spoke:
ip route 0.0.0.0 0.0.0.0 <ISP Gateway of spoke>
ip route 192.168.48.0 255.255.240.0 <Hub Tunnel IP>
In our old site-2-site scenario, we would simply point the default route to the Tunnel interface and then the traffic would flow that way and then statically route any other data we want to go elsewhere. However, I've noticed in this scenario that is not the case. Also, when I go to point the default route somewhere else than the ISP Gateway (even to the Hub tunnel ip), I lose all connectivity to the Hub lan.
Basically, I just need all traffic from the spoke to traverse the tunnel to the hub, where all resources and internet access will come from. Any advice would be appreciated!

Hi Ken,
Not a typical requirement to route 0/0 to dmvpn hub. For that you need:
1. correct routing on spoke which will point to tunnel for 0.0.0.0/0
You can achieve that via static or dynamic routing, example:
ip route (this to have tunnel connectivity)
ip route 0.0.0.0 0.0.0.0 (all traffic send thru tunnel)
I have never tested that scenario - but that would be my try.
Michal

Similar Messages

Why can't I get internet from my AirPort Express?

I have an AirPort Express. I have three iPhones, two MacBooks, one iMac, one iPad, two Xbox 360's, a Wii and an HP printer connected to it. My dad has a toshiba laptop running windows vista and I can't get internet from it. I can connect to the AirPort Express just fine. I have exelent signal and all. But when I try to go online it says I dont have any internet. I ran the diogostics and it said theres no internet connection when clearly there is when I have all these devises connected to it without any problem at all. Can someone please help me out and tell me why and how I can fix it?

Hi - I just upgraded from an Airport Extreme to Time Capsule. The MacBook Pros and old iBook went on the new network fine, but my Toshiba did the same thing as yours. After hours of trying to figure out the settings myself (including reading this forum), a couple of calls to Apple and lots of troubleshooting they referred to me Toshiba. It took two calls to Toshiba (and a $49 troubleshooting fee), but it's now working. The second tech took over my computer remotely, deleted the old Atheros network software and did an upgrade. It's working great now! Good luck.

How do I create a new account and get stuff from the old account to the new account

How do I create a new account and get stuff from the old account to the new account

There are instructions on this page for creating a new account : Set up an Apple ID in iTunes
Or if you don't want to give credit card details : Create an iTunes Store, App Store, or iBooks Store account without a credit card or other payment method
But you won't be able to transfer purchases from your old account to it, all content that you download from the store will remain tied to the account that downloaded it.

Arch can't get internet from router [SOLVED *knocks on wood*]

I setup a linksys router, and it doesn't work properly with arch. I can connect to it, but there's no internet.
Other computers on the router can get internet, and windows vista on the same computer as arch can.
There is another router upstream from this one.
The new router uses a static IP, and arch uses DHCP.
Last edited by Raccoon1400 (2009-04-13 22:07:31)

I can't ping any of the IP addresses for Google.
I can ping the router.
I can' ping a URL.
duncan@duncan-arch ~]$cat /etc/rc.conf
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="localtime"
USEDIRECTISA="yes"
TIMEZONE="Canada/Eastern"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=(bcm43xx b43 ssb) #deprecated
MODULES=(mii ndiswrapper b44 snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel acpi-cpufreq cpufreq_ondemand cpufreq_powersave soundcore vboxdrv usblp fuse iwl3945)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="duncan-arch"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
eth0="dhcp"
wlan0="dhcp"
INTERFACES=(eth0 wlan0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
#gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng dbus @cpufreq @hal alsa @dhcdbd @networkmanager @crond @cups)
duncan@duncan-arch ~]$
duncan@duncan-arch ~]$cat /etc/resolv.conf
# Generated by NetworkManager
nameserver 67.69.235.1
nameserver 207.164.234.193
duncan@duncan-arch ~]$

HT1515 do you have to do to get internet from the airport express?

what do you have to do to get internet fron the airport express?

Plug in your Cable or DSL modem into the Airport and setup the Airport for wireless Internet.

Getting new computer - how get itunes from old computer to new one?

Hello: I am in the process of getting a new desktop computer. Currently in itunes I have about 100 songs (I just got the ipod the other day). My current computer only has USB 1.1 so I am excited to be able to use USB 2.0 with the new machine. So, how do I get all of my songs on itunes from my current computer to the new one? Sorry if this is a stupid question, however I am very new to ipods. Thanks

For me, using a computer network is the easiest, and fastest.
Next would be using DVDs
then CDs
then the iPod.
Sounds like you have never burned a CD/DVD or backed up any of your music. You do know you only get the one-time download per track from the iTMS, don't you?

Syncing music from your ipod to a new computer and getting music from the new computer

I have an old ipod nano and I recently go a new mac book pro. I want to sync the music from the nano onto my mac book and then sync the music from my mac book on to my ipod. Please help

Do you have any ripped, non-purchased music? That is, music that you ripped off of CD's and imported into your iTunes library as opposed to buying from the iTunes Store. If you do not have any of this music, your solution is simple: connect your iPod to iTunes, then go to File>Devices>Transfer Purchases from "[iPod name]". All of the music from your iPod will be transferred onto your MacBook. After that, sync your iPod to get the music that is on your MacBook and not on your iPod, on your iPod.
If you do have ripped music, however, you will have a much more difficult time. Is this the case?

New on POO : get items from purchase order

Hi,
i'm new in OO, i must implement the BADI IF_EX_ME_PROCESS_PO_CUST~CHECK. In this method i would like to get items of my current purchase order, how can i do that ?
Thanks a lot.
Cheers

Hello
Please note that if you have understood this BAdI then you have understood the basics of ALL BAdIs dealing with business objects that have a header and one or more items.
Example: BAdI ME_PROCESS_REQ_CUST (purchase requisition)
METHOD if_ex_me_process_REQ_cust~check.
* define local data
DATA:
    lt_items      TYPE mmpur_requisition_items,
*    ls_item       LIKE LINE OF lt_items, " alternatively
    ls_item       TYPE mmpur_requisition_item,
    ls_header     TYPE mereq_header.
" Change data types of local variables (compared to if_ex_me_process_PO_cust~check)
" but use the very same coding to retrieve the items.
* (1) Get the order items
* CALL METHOD im_header->get_items
*    receiving
*      re_items = lt_items.
* Short version:
lt_items = im_header->get_items( ).
LOOP AT lt_items INTO ls_item.
    ls_detail = ls_item-item->get_data( ).
*   do something ...
ENDLOOP.
* (2) Get header data
* CALL METHOD im_header->get_data
*    receiving
*      re_data = ls_header.
* Short version:
ls_header = im_header->get_data( ).
ENDMETHOD.
Regards
Uwe

Get internet from my blackberry bold to my tungsten E2

Could somebody tell me if there is any way to pair my blackberry bold with my tungsten E2 to get on the web... send e-mails etc.... Palm does not have a phone link for blackberry .
Thanks a lot
Post relates to: Tungsten E2

Hello Coaxial, Welcome to the Palm Community Forums!
AFAIK, there is no way to tether your E2 to a RIM device... I've tried many times to use my wife's Pearl as a connection for my TX's (using AT&T). The SonyEricssons I've had, Motorolas, and my Centro all work fine.
BlackBerry and LG are two phones that have little cooperation with PalmOS devices.
WyreNut
I am a Volunteer here, not employed by HP.
You too can become an HP Expert! Details HERE!
If my post has helped you, click the Kudos Thumbs up!
If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

New client cant get ip from dhcp server (web authentication)

We have WLC 5508 with two SSID staff (vlan 58, PSK auth) and customer (vlan 48, web auth)
Recently, new client can connect to SSID staff without problem but It cant get IP when it connect to Customer SSID.
many other client ( smart phone, laptop) which connect for few week still connect to Customer normally.
DHCP server still have a lot of IP for wireless client.
We want to use firewall to make policy for Customer so we put gateway of vlan 48 on the firewall.
Please check the dubug client file.
Thanks.

The debug just shows a single DHCP Discover attempt when attaching to WLAN with VLAN 48 interface. It appears the client is simply not pulling an IP (not the WLCs responsibility), although you are using DHCP-Proxy.
Can you put a wired client in VLAN 48 on the same switch as the WLC and have a client pull an IP?

Connecting a WRT54G v2 to BEFSR41. How do I do it to get internet access with both?

So recently I just bought a BEFSR41 to split the internet coming from a cat5e cable from the WRT54G so I can get internet on both my xbox 360 and computer, but I've run into a bunch of issues. First off, I've tried turning my BEF into an access point by creating a new IP, disabling DHCP and connecting it to a numbered port, but I can't get internet from that solution. I've called tech support to see if they could help but I just wasted 2 hours of their time because all the solutions they tried didn't work either. So I'm wondering if its my cable thats the problem. Its a CAT5e cable branched through my room to the office room I say about 50 to 100 feet away. I receive internet through this cable when i connect it to the computer but when i connect it to the xbox it doesnt even register an ip. Also when i connect this cable to my very old netgear router RT314, it can receive internet but it has trouble with connecting to different users. Any help will be much appreciated. Cable Modem----(internet port)WRT54Gport4-----BEFSR41 port4---computer.

Read through this page and see if you find some help......
http://www3.nohold.net/noHoldCust56/Prod_6/KnowledgePortal/KPScripts/amsviewer.asp?docid=1a47dca0dd6...

MDB messages dont get processed from Queues when involving a remote Topic in transaction

Using WLS 6.1 SP4 on winXP Pro boxes, I have come across a peculiar problem:
          I have several MDBs that process ObjectMessages from queues and forward their payload (wrapped in another new ObjectMessage) to other queues, all of which are located within the same WLS server.
          Right now I'm adding a new MDB that gets messages from a remote Topic with a durable subscription, and forwards the payload to local queues after some processing.
          When the Topic is local as well, there is no problem. But when the Topic is set up in a remote machine, only the MDB that has the remote durable subscription works the way it should. It receives the remote message and forwards it to the corresponding local queue. But then the messages in those local queues dont get processed. The 'Messages Received' count rises and the 'Messages' count stays at 0, as if the messages had been correctly processed and acknowledged, but no onMessage() method is called besides the one from the MDB that has the durable subscription to the remote Topic (I can tell because there's no further processing from the queue those messages get put in). It's as if those messages were simply received and acknowledged without being passed to other MDBs by WLS.
          * All queue MDBs use Required container-managed transaction management and auto-acknowledge
          * All queue MDBs have default durability for their queue subscriptions
          * The topic MDB has a durable subscription stored in a filestore
          * Lookup of the remote Topic is done via JNDI
          Since the processing and forwarding of messages occurs the way it should when everything is local, I am inclined to believe one of two things:
          a) There's some issue with the way WLS treats messages (or even just payloads) when they come from a remote server
          b) WLS is doing something I'm not aware of when propagating a transaction that begins with the delivery of a message from a remote JMS Topic when it involves further forwarding of messages in local JMS Queues.
          Any help will be appreciated.
          regards,
          .munir estevane


Is the durable subscriber forwarder rolling back its transactions?
          That would cause the behavior you describe (eg the message gets
          placed in the queue, but is never made visible). What do
          the pending counts on the destination queue look like?
          Munir Estevane wrote:
          > Using WLS 6.1 SP4 on winXP Pro boxes, I have come across a peculiar problem:
          >
          > I have several MDBs that process ObjectMessages from queues and forward their payload (wrapped in another new ObjectMessage) to other queues, all of which are located within the same WLS server.
          > Right now I'm adding a new MDB that gets messages from a remote Topic with a durable subscription, and forwards the payload to local queues after some processing.
          >
          > When the Topic is local as well, there is no problem. But when the Topic is set up in a remote machine, only the MDB that has the remote durable subscription works the way it should. It receives the remote message and forwards it to the corresponding local queue. But then the messages in those local queues dont get processed. The 'Messages Received' count rises and the 'Messages' count stays at 0, as if the messages had been correctly processed and acknowledged, but no onMessage() method is called besides the one from the MDB that has the durable subscription to the remote Topic (I can tell because there's no further processing from the queue those messages get put in). It's as if those messages were simply received and acknowledged without being passed to other MDBs by WLS.
          >
          > * All queue MDBs use Required container-managed transaction management and auto-acknowledge
          > * All queue MDBs have default durability for their queue subscriptions
          > * The topic MDB has a durable subscription stored in a filestore
          > * Lookup of the remote Topic is done via JNDI
          >
          > Since the processing and forwarding of messages occurs the way it should when everything is local, I am inclined to believe one of two things:
          > a) There's some issue with the way WLS treats messages (or even just payloads) when they come from a remote server
          > b) WLS is doing something I'm not aware of when propagating a transaction that begins with the delivery of a message from a remote JMS Topic when it involves further forwarding of messages in local JMS Queues.
          >
          > Any help will be appreciated.
          >
          > regards,
          > .munir estevane

How do I get photos from aperture to iPhone?

so far, photostream seems to be working fine as far as moving pics from my iPhone to Aperture 3/iPhoto.
After the IOS5 update, I realized I have none of the pictures on my phone I originally had.
Is there a new process to get pictures from Aperture / iPhoto to my iPhone or is it the same plug and sync routine?
Thanks

I think the original poster may have the same issue I'm facing...
iTunes does not sync Aperture pictures to the iPhone if they originate from Photostream! That is, in Aperture I have events like "Jan 2012 Photostream", "Feb 2012 Photostream" and so on. But those events do not sync with the iPhone via iTunes! That's why the photos that originally used to be on the Photostream, but have since deleted because they have become more than 30 days old, are no longer on your iPhone.
I've been trying with AppleCare to sort out the issue, but so far they don't seem to know what's causing it. I think it's probably a bug in either Aperture or iTunes.

How Do I Get internet form other places

I have herd that you can get internet from a certain place for free from in your street of example. Someone had told me that there is a special place in streets where there is a open internet link? How do I find this Connection??
Please need help this is my first posted message
Hope you can help Thanks
*Keep It*

you can use the wi-fi on your ipod to access public wi-fi networks (or indeed unsecured private networks.) some public networks are free, others aren't. the best way to show this is to go for a walk around your neighbourhood, with your ipod wi-fi networks screen showing, refreshing every so often. you will no doubt come across numerous private wi-fi networks, most of them will be secure and will have a padlock next to them, you may strike lucky and find an unsecure one that you don't need a password to access.
google "wi-fi hotspots". this will enable you to find hotspots near you.

Internet from 7100 STB RJ45 jack?

The 7100-P1/P2 STB has an RJ45 jack on the back. Can I get internet from this port for u-tube / netflix viewing? Or do I need to run a separate CAT5/6 cable from the router to the TV ?

Search for Ethernet Jack has a few hits.
http://forums.verizon.com/t5/forums/searchpage/tab/message?filter=location&location=Board%3AFiOS_TV&...
STB Ethernet
http://forums.verizon.com/t5/FiOS-TV-Technical-Assistance/fios-stb-ethernet-jack/m-p/19763#M8706
I know some people that have relocated the router to the TV location. There are various options.

New to DMVPN - Getting internet from Hub to Spoke

Similar Messages

Maybe you are looking for