Nexus 5548UP Downgrade from 5.1.3.N1.1 to 5.0.3.N2.2b fails -- SRG file not present/cannot be opened

I am attempting to downgrade from 5.1.3.N1.1 to 5.0.3.N2.2b for standards compliance.
When following the ISSU steps for validation of the install all command I receive the following error on the following command:
sh install all impact kickstart bootflash:n5000-uk9-kickstart.5.0.3.N2.2b.bin system bootflash:n5000-uk9.5.0.3.N2.2b.bin
Verifying image bootflash:/n5000-uk9-kickstart.5.0.3.N2.2b.bin for boot variable "kickstart".
[####################] 100% -- SUCCESS
Verifying image bootflash:/n5000-uk9.5.0.3.N2.2b.bin for boot variable "system".
[####################] 100% -- SUCCESS
Verifying image type.
[####################] 100% -- SUCCESS
Extracting "system" version from image bootflash:/n5000-uk9.5.0.3.N2.2b.bin.
[# ] 0% -- FAIL. Return code 0x404F0003 (SRG file not present/cannot be opened).
I followed some recommendations from this post https://supportforums.cisco.com/thread/2108814
reload to clear temp and cache
show system internal flash
checked md5sum of image
I found this information http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/deferral/Deferral_Advisory_Notice_N5K.html
I am unsure of how to upgrade when the steps to validate indicate a problem with the upgrade/downgrade.
I still receive the error.
Any help would be greatly appreciated.
Attached are the steps done so far and outputs.

I had already created a case with our reseller. The engineer there had me reload the 5ks and attempt the show install all impact again. When I did it was successful.
I was able to then downgrade to 5.0.3.N2.2b. I am currently working to duplicate the issue by going back to 5.1.3.N1.1.
The engineer also stated that I was probably running into this bug:
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsw25835
Here is the contents of the sh system internal flash and show system internal dir /var/tmp:
Mount-on                  1K-blocks      Used   Available   Use% Filesystem
/                            409600     72564      337036     18   /dev/root
/proc                             0         0           0      0   proc
/post                          2048         4        2044      1   none
/var                         409600     72564      337036     18   none
/sys                              0         0           0      0   none
/isan                       1536000    409628     1126372     27   none
/var/tmp                     307200        72      307128      1   none
/var/sysmgr                 1024000         0     1024000      0   none
/var/sysmgr/ftp              409600        68      409532      1   none
/var/sysmgr/ftp/cores        102400         0      102400      0   none
/callhome                     61440         0       61440      0   none
/dev/shm                     524288    126552      397736     25   none
/volatile                    153600         0      153600      0   none
/debug                        20480         0       20480      0   none
/dev/mqueue                       0         0           0      0   none
/debugfs                          0         0           0      0   nodev
/mnt/plog                     49024      1300       47724      3   /dev/mtdblock2
/mnt/cfg/0                   114909      4274      104702      4   /dev/sda5
/mnt/cfg/1                   112920      4274      102816      4   /dev/sda6
/var/sysmgr/startup-cfg      409600      2104      407496      1   none
/dev/pts                          0         0           0      0   devpts
/mnt/pss                     114917      5923      103060      6   /dev/sda4
/bootflash                  1609984    779460      748740     52   /dev/sda3
                                                                ./         640
                                                               ../         240
                                                   bootloader_ver            0
                                           util_cli_history_admin           48
                                                            mysrg         1664
                                                    mcm_ascii.log         1019
                                                 m2rib_ascii.3248           68
                                                           arping          101
                                                        stp.log.1         3836
                                                         fwm1.out            0
                                                    cmp_slot_id.1            0
                                                           ntpd_1            0
                                                     ntp_client_1            0
                                                 ntp__libdapi.log            0
                                                 igmp_restart.log            0
                                                 radius_debug.log          232
                                                      cfs_mac.log          166
                                                       climib.log         1416
                                                          lcc.log          694
                                                  security_stderr           77
                                                  security_stdout            0
                                                    aaa_debug.log          519
                                               security_debug.log          647
                                                        evmc.3005           31
                                                       idehsd.log          602
                                                        mvsh.3000            0
                                                        lockcisco            0
                                                          .flexlm/          60
                                                             logs@          20
                                                  first_setup.log         2981
                                                  boot_uptime.log           56
                                                              vsh/          40

Similar Messages

Nexus 7009: Downgrading from 6.2.1 to 5.2.9

Hello!
When i try to downgrade a N7009 from 6.2.1 to 5.2.9, i got htis error
switch# show install all impact kickstart n7000-s1-kickstart.5.2.9.bin system n7000-s1-dk9.5.2.9.bin
Installer will perform impact only check. Please wait.
Verifying image bootflash:/n7000-s1-kickstart.5.2.9.bin for boot variable "kickstart".
[# ] 0% -- FAIL.
Return code 0x40450030 (Digital signature verification failed).
Pre-upgrade check failed. Return code 0x40930011 (Image verification failed).
Still the MD5 checksum from both files are absolutely identical! Need you help.
David

Hi David,
Is NX-OS 6.2(1) the correct version? The reason I ask this is because as far as I'm aware this release is not officially available at this time. I've just checked again and there are no release notes or download option for NX-OS 6.2 on CCO currently.
Assuming you've not made a typo in the release you're trying to downgrade from, the best advice I can offer at this point would be to attempt a multistep downgrade to either NX-OS 6.1 or 6.0 first. It may be that a single step downgrade from NX-OS 6.2 to 5.2 is not a supported option, but as there's no documentation for NX-OS 6.2 at this time we don't know.
At least if you can get to either a 6.1 or 6.0 release, then when you attempt the downgrade to NX-OS 5.2 it'll be one shown as supported.
Regards

I tried to download my photos from the memory card to my computer but I got an error message of " file not found ". What would cause this ?

When I inserted my memory card from the camera into the computer it opened the Adobe window. I clicked on the get photos icon and the process of downloading to the computer began as usual. But when it was complete an error message came up No file found. Now I cannot open anything to view any of my previous photos. How do I fix this ?

The Camera Connection Kit works with SD cards, not Memory Sticks.
Maybe you can find an MS to SD adapter, or use the USB connection with the USB cable that came with the camera.

Downgrading from win 8 to win 7 a lenovo x240

or a link

diallooumar wrote:
downgrading from win 8 to win 7 a lenovo x240
I'm - downgrading from win 8 to win 7 a lenovo x240
downgrading from win 8 to win 7 a lenovo x240 - Is it possible?
I'm not sure if you are asking if you can or telling us you are doing it, either way if you can you may need to get the media from Lenovo, or stick with 8 and wait a month then get yourself Windows 10

How to downgrade from iOS 6 to iOS 5.1.1

How to Downgrade from iOS 6 to iOS 5.1.1?

I'm sorry, but Apple does not provide a downgrade path for iOS. Because downgrading is unsupported by Apple we cannot discuss it on these forums, but you can use Google to find information on how to install an older version of iOS on any iDevice.

How do I downgrade from ios6

I don't like apple maps. How do I downgrade from ios6 so I can get google maps and streetview again?

It's a pity one cannot downgrade, google maps streetview was really good.
My local underground station has a sign explaining "iphone ios6 users can get a paper map from the information stand". I believe someone wrote it on there. Did make me laugh. I hope Apple get to grips with their maps version, perhaps they could have waited until it was somewhat better. Anyway, thanks for the reply.

My latest attempt to import photos from my slr resulted in an error. Something to thew effect of file not compatible. never had this problem before.

My latest attempt at moving photos from my slr to iphoto resulted in an error, something to the effect of file not compatible. Never happened before. Made about six attempts...no change. any ideas?
Thanks

What system and iPhoto versions are you using? What camera model and are you shooting just jpegs or RAW or both?
See if you can launch Image Capture and get it to recognize your camera. If it does then download the photos to a folder on the Desktop to get them safely on the hard drive.
See if the files can be imported into iPhoto from that folder.
Reformat the memory card with your camera, take some test shots and try to import into iPhoto directly.
OT

Nexus 5548UP snmp gathering information from FC is not working

Hi all,
We have a couple of Nexus 5548UP.
Nx-OS = n5000-uk9.7.0.5.N1.1.bin
monitoring traffic of FC interfaces was working fine until we upgraded to 7.0.5.N1.1 from 6.0.2.N2.1.
We didn't change anything on our Nexus config and on our Centreon monitoring engine.
I also can't see Fc interface while browsing MIBs from the Nexus.
Is there any issue or something to do to recover the monitoring of The FC interface of the Nexus ?
Best Regards
Cyril

Hi,
It might be this bug.
FC interfaces are not listed in IF-MIB snmp walk
CSCup75270
-->Fixed in NX-OS 7.0(6) and above.

LMS User Tracking for NEXUS 5548UP

Dear,
A while ago I received a ticket from one of our customers because User Tracking was not working for NEXUS 5548UP on LMS 3.2. I opened a TAC case for this but this was normal since it is a Datacenter switch. Now the customer came back on this because they really want to see which server is connected to which switch port. I understood from the TAC engineer this is not on the roadmap to integrate in LMS 4.x. They want to know if there exists another product (they thought about DCNM) and wanted to know how this integrates or works together with LMS...
Kind regards,
Sven Laureyssens

My latest understanding of User Tracking and Nexus 5K series is that it is not supported due to a limitation of the MIB support in the NX-OS.
The current DCNM (release 5.2) is distinct from the LMS and Cisco Prime umbrella but that wil be changing a bit moving forwad as DCNM is enhanced and rolled into the Cisco Prime family. Last I heard there should be some information coming out of Cisco Live this week and a new release will have some additional functionality and better integration. Still, I doubt we'll see UT for the 5K due to the NX-OS limitation.
One way to do what you're asking apart from use of any of the Cisco products is to enable LLDP on your Nexus and servers. That will at least give you the ability to pull the information from the NX-OS command line ("show lldp neighbor")

C-200 M2 with P81E to Nexus 5548UP

Hi all,
I'm working on a project which is about to set up a Cisco UCS Lab.
Actually the topology looks simple and easy but there must be some missconfiguration on my side because i can't see any of IDs (P81E's wwpn and mac address info) from the Nexus 5548UP.
I connected my 5548UP to MDS 9124 for providing the FCoE traffic to the C-200 Farm.
Then i configured the MDS with NPIV and converted couple of ethernet ports to the FC ports on 5548UP (which i'm using to connect to the MDS)
Finally i connected my C-200M2's VIC to the 5548UP but i couldn't see any information about server. The ports actually are up. But can't see nothing.
Some help and advises will be appreciated.

Padma,
Right now i connected the N5548 directly to the storage for that reason you can not see the fc uplink connections on running-configuration.
On Nexus 5548 ;
     Ethernet 1/1 and Ethernet 1/2 are the server ports (P81E)
     Ethernet 1/15 is the Uplink Ethernet port
     Fc 1/31 1/32 is the Storage Ports
     Storage has been configured for the wwpns and LUNs.
And here is the configuration :
N5548(config-if)# show running-config
!Command: show running-config
!Time: Tue Jan 24 13:32:53 2012
version 5.0(3)N2(1)
feature fcoe
feature telnet
feature lldp
username admin password 5 $1$XCMHODt3$yEItwOs0Vl.LLYyXBPjZu0 role network-admin
no password strength-check
ip domain-lookup
hostname N5548
class-map type qos class-fcoe
class-map type queuing class-fcoe
match qos-group 1
class-map type queuing class-all-flood
match qos-group 2
class-map type queuing class-ip-multicast
match qos-group 2
class-map type network-qos class-fcoe
match qos-group 1
class-map type network-qos class-all-flood
match qos-group 2
class-map type network-qos class-ip-multicast
match qos-group 2
slot 1
port 1-24 type ethernet
port 25-32 type fc
snmp-server user admin network-admin auth md5 0x29cde3d41c6724dcbec14cf28387824d
priv 0x29cde3d41c6724dcbec14cf28387824d localizedkey
snmp-server enable traps entity fru
vrf context management
vlan 1
fcoe vsan 1
fcdomain fcid database
vsan 1 wwn 50:06:0e:80:10:4d:03:60 fcid 0xa10000 dynamic
vsan 1 wwn 50:06:0e:80:10:4d:03:62 fcid 0xa10001 dynamic
interface vfc1
bind interface Ethernet1/1
no shutdown
interface vfc2
bind interface Ethernet1/2
no shutdown
interface fc1/25
interface fc1/26
interface fc1/27
interface fc1/28
interface fc1/29
interface fc1/30
interface fc1/31
no shutdown
interface fc1/32
no shutdown
interface Ethernet1/1
interface Ethernet1/2
interface Ethernet1/3
interface Ethernet1/4
interface Ethernet1/5
interface Ethernet1/6
interface Ethernet1/7
interface Ethernet1/8
interface Ethernet1/9
interface Ethernet1/10
interface Ethernet1/11
interface Ethernet1/12
interface Ethernet1/13
interface Ethernet1/14
interface Ethernet1/15
switchport mode trunk
speed 1000
interface Ethernet1/16
interface Ethernet1/17
interface Ethernet1/18
interface Ethernet1/19
interface Ethernet1/20
interface Ethernet1/21
interface Ethernet1/22
interface Ethernet1/23
interface Ethernet1/24
interface mgmt0
ip address 192.168.10.210/24
line console
line vty
boot kickstart bootflash:/n5000-uk9-kickstart.5.0.3.N2.1.bin
boot system bootflash:/n5000-uk9.5.0.3.N2.1.bin
interface fc1/25
interface fc1/26
interface fc1/27
interface fc1/28
interface fc1/29
interface fc1/30
interface fc1/31
interface fc1/32
N5548(config-if)#

Nexus 5548UP L3 card swap out for L2 cards

Hi everyone,
I have two Nexus 5548UPs and I am going to swap out the L3 cards and put in L2 cards.
I can't seem to get a straight answer out of TAC so I thought I'd try here.
How will this affect the current configuration (apart of course from removing the L3 capability)?
Will swapping the cards clear the config?
Will swapping the cards clear the licenses?
It's a very simple config so that doesn't worry me that much .. but if it will clear the licenses installed than I need to take action on that.
Thanks,
BR

no, no secret aukhadiev
I made a mistake without realising and the interface e1/3 was showing "Interface Ethernet1/3 is down (Inactive)". After spending sometime trying to figure out what was wrong with that interface or switch, it turned out to be that i forgot to add the vlan 40. Now the config looks like this:
N5K-C5548UP Switch
feature interface-vlan
feature lacp
feature dhcp
feature lldp
vrf context management
ip route 0.0.0.0/0 172.16.0.1
vlan 1
vlan 40
vlan 100
service dhcp
ip dhcp relay
interface Vlan1
no shutdown
interface Vlan40
description ** Server VLAN **
no shutdown
ip address 10.144.40.3/25
ip dhcp relay address 10.144.40.39
ip dhcp relay address 10.144.40.40
interface port-channel1
description ** Trunk Link to Switch A g1/0/23-24 **
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,122
speed 1000
interface Ethernet1/1
description ** Trunk Link to Switch A g1/0/23**
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,12
speed 1000
channel-group 1 mode active
interface Ethernet1/2
description ** Trunk Link to Switch A g1/0/24**
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,122
speed 1000
channel-group 1 mode active
interface Ethernet1/3
description **Connected to server B**
switchport access vlan 40
speed 1000
interface mgmt0
description connection to Switch A g2/0/20
no ip redirects
ip address 172.16.0.2/25
Thank you,
JN

Fc ports on nexus 5548up.

Hi Guyz,
I have a pair of nexus 5548UP with expansion module N55-M16UP. both switches have below licensing.
Feature Ins Lic Status Expiry Date Comments
Count
FCOE_NPV_PKG No - Unused -
FM_SERVER_PKG No - Unused -
ENTERPRISE_PKG Yes - Unused Never -
FC_FEATURES_PKG Yes - In use Never -
VMFEX_FEATURE_PKG Yes - Unused Never -
ENHANCED_LAYER2_PKG No - Unused -
LAN_BASE_SERVICES_PKG Yes - In use Never -
LAN_ENTERPRISE_SERVICES_PKG Yes - Unused Never -
on first switch i made slot 2 as fc ports & after reload i can see fc ports.
slot 2
port 1-16 type fc
However with same procedure on switch 2 , i cant see any FC ports nor module 2 ports.
if i turn module 2 ports to ethernet i can see E2/1 - E2/16 , but no ports when they are configures as FC.
any idea ???
Confused as both switches have same lic installed.
Thanks in Advance.

After the port type has been changed from Ethernet to FC, the FC port will not be enabled on the switch until FCOE feature is enabled:
N5K(config)#feature FCOE
C license checked out successfully
fc_plugin extracted successfully
FC plugin loaded successfully
FCoE manager enabled successfully
FC enabled on all modules successfully
Enabled FCoE QoS policies successfully
After that, we verify that the port type is changed successfully and the FC ports appear on the switch:
N5K# show interface brief

Nexus 5548P vs Nexus 5548UP

I have a question regarding Nexus 5548UP which is supported from NXOS 5.0.3 on.
I assume thats the absolute indentical hardware as the Nexus5548P which was available a little bit
earlier and had also the HW ready for support Unified Ports on all Ports (but was just enabled on expansion-module).
Is it possible by SW upgrade to 5.0.3 to make a 5548UP from a 5548P ?
Thx
hubert

Thx Lucien,
then there is absolutely no reason to buy the 5548P, because 5548UP has same price, and no reason to buy another expansion-module than the UP(has the same price as well compared to the other expansion Module ?
So I assume 5548P and the pure Eth-uplink Modul, and the mixed FC and Eth-uplink Modul will have very limited lifetime ?!
One additional Question: I read that in case a 5596 has L3-Modul built in , it no longer supports the maximum numbers of FEXes it supports only 8 then.
Is this a limitation which will remain, or is there a chance new NX-OS Versions will break thhis limit
KR
Hubert

Connecting many Brocade switches to Nexus 5548UP

Hello,
I have a SAN network composed of few separate PODs. Each POD is divided into SAN-A and SAN-B. Most of those PODs are Brocade switches (FOS 6.1). There are also few Nexus 5520s. Now, we have built new core infrastructure with Nexus 5548UPs and many MDS 9148s. We would like to move all servers and sotrage from old Brocades to the new SAN. As we cannot move all devices at the same time, all segments must be connected to the core for some time. Each POD has different zoning. Some zonings on Brocade switches are based on PWWN, some on Domain ID and Port ID. In my opinion, the only way of successfuly connecting all PODs together is to merge zones manualy (in excel, etc). and paste them on all switches. However, maybe there is some other way of merging all zones? What if I leave Nexus 5548UP in native mode (so zones from Brocade will not get merged), and only implement that manually merged zoneset on Nexus 5548UP? Will the ISL links get isolated due to zoning merge failure? Or they will maintain operational state even if zones are different on each POD? I do not have any lab boxes, so I cannot test it. Any advidse will be appreciated.
Best regards,
Krzyszof

well since you can not cluster the 45K as a virtual switch ( Cisco with new sup will start support VSS in the 4500 try to check which sup exactly and if you can upgrade as this will make a significant improvement to your design )
anyway the only method that you can use currently is the traditional way which is depending on STP ( use rapid-PVST)
from each N5K use one separate link to each 45K and STP will put on of the links in blocking mode
however you might do some STP and vlan design for load sharing where you can send vlan x over link1 and vlan y over link b to the 45K using STP cost
HTH

Nexus 5548UP with 1Gb ether to 10Gb ether on same switch

I have a Nexus 5548UP switch with a couple of systems some of which have been configured with 1Gb nic's running various OS's and other that have 10Gb nic's. When I try to SSH from 1Gb box to a 1Gb box everything is fine, when I SSH from 1Gb to 10Gb box it does not work but 10Gb to 10Gb boxes will work. The switch is a fresh install and has one VLAN 51 the first 2 ports are setup with LACP and the only differences is speed of 1000 and 10000 for the boxes attached. Is there some trick or additional configuration that is needed to make 1Gb to 10Gb work for SSH and other applications? I trying to setup some test boxes now to have a repeatable environment and will update when completed.
!Command: show running-config
!Time: Fri Jan 9 18:30:44 2009
version 5.2(1)N1(4)
hostname ISC5548B
no feature telnet
feature lacp
feature lldp
...... account info removed
ssh key rsa 2048
ip domain-lookup
class-map type qos class-fcoe
class-map type queuing class-fcoe
match qos-group 1
class-map type queuing class-all-flood
match qos-group 2
class-map type queuing class-ip-multicast
match qos-group 2
class-map type network-qos class-fcoe
match qos-group 1
class-map type network-qos class-all-flood
match qos-group 2
class-map type network-qos class-ip-multicast
match qos-group 2
vrf context management
ip route 0.0.0.0/0 192.168.52.1
vlan 1
vlan 51
name InfoSec
port-profile default max-ports 512
interface port-channel1
switchport access vlan 51
speed 1000
interface Ethernet1/1
lacp port-priority 500
switchport access vlan 51
speed 1000
channel-group 1 mode active
interface Ethernet1/2
switchport access vlan 51
speed 1000
channel-group 1 mode active
interface Ethernet1/3
switchport access vlan 51
speed 1000
interface Ethernet1/4
switchport access vlan 51
speed 1000
interface Ethernet1/5
switchport access vlan 51
speed 1000
interface Ethernet1/6
switchport access vlan 51
speed 1000
interface Ethernet1/7
switchport access vlan 51
speed 1000
interface Ethernet1/8
switchport access vlan 51
speed 1000
interface Ethernet1/9
switchport access vlan 51
speed 1000
interface Ethernet1/32
switchport access vlan 51
speed 1000
interface Ethernet2/1
switchport access vlan 51
interface Ethernet2/2
switchport access vlan 51
interface Ethernet2/3
switchport access vlan 51
interface Ethernet2/4
switchport access vlan 51
interface Ethernet2/5
switchport access vlan 51
interface Ethernet2/6
switchport access vlan 51
interface Ethernet2/7
switchport access vlan 51
interface Ethernet2/8
switchport access vlan 51
interface Ethernet2/14
switchport access vlan 51
interface Ethernet2/15
switchport access vlan 51
interface Ethernet2/16
switchport access vlan 51
interface mgmt0
ip address 192.168.52.4/24
line console
line vty
boot kickstart bootflash:/n5000-uk9-kickstart.5.2.1.N1.4.bin
boot system bootflash:/n5000-uk9.5.2.1.N1.4.bin
ISC5548B# show int brief
Ethernet      VLAN    Type Mode   Status Reason                   Speed     Port
Interface                                                                    Ch #
Eth1/1        51      eth access up      none                       1000(D) 1
Eth1/2        51      eth access up      none                       1000(D) 1
Eth1/3        51      eth access up      none                       1000(D) --
Eth1/4        51      eth access up      none                       1000(D) --
Eth1/5        51      eth access up      none                       1000(D) --
Eth1/6        51      eth access up      none                       1000(D) --
Eth1/7        51      eth access up      none                       1000(D) --
Eth1/8        51      eth access up      none                       1000(D) --
Eth1/9        51      eth access up      none                       1000(D) --
Eth1/10       51      eth access up      none                       1000(D) --
Eth1/11       51      eth access up      none                       1000(D) --
Eth1/12       51      eth access up      none                       1000(D) --
Eth1/13       51      eth access down    Link not connected         1000(D) --
Eth1/14       51      eth access down    Link not connected         1000(D) --
Eth1/15       51      eth access up      none                       1000(D) --
Eth1/16       51      eth access down    Link not connected         1000(D) --
Eth1/17       51      eth access down    SFP not inserted           1000(D) --
Eth1/18       51      eth access down    SFP not inserted           1000(D) --
Eth1/28       51      eth access down    SFP not inserted           1000(D) --
Eth1/29       51      eth access down    SFP not inserted           1000(D) --
Eth1/30       51      eth access down    SFP not inserted           1000(D) --
Eth1/31       51      eth access down    SFP not inserted           1000(D) --
Eth1/32       51      eth access down    SFP not inserted           1000(D) --
Eth2/1        51      eth access up      none                        10G(D) --
Eth2/2        51      eth access up      none                        10G(D) --
Eth2/3        51      eth access up      none                        10G(D) --
Eth2/4        51      eth access up      none                        10G(D) --
Eth2/5        51      eth access up      none                        10G(D) --
Eth2/6        51      eth access up      none                        10G(D) --
Eth2/7        51      eth access down    SFP not inserted            10G(D) --
Eth2/8        51      eth access down    SFP not inserted            10G(D) --
Eth2/9        51      eth access down    SFP not inserted            10G(D) --
Eth2/10       51      eth access down    SFP not inserted            10G(D) --
Eth2/11       51      eth access down    SFP not inserted            10G(D) --
Eth2/12       51      eth access down    SFP not inserted            10G(D) --
Eth2/13       51      eth access down    Link not connected          10G(D) --
Eth2/14       51      eth access down    SFP not inserted            10G(D) --
Eth2/15       51      eth access down    Link not connected          10G(D) --
Eth2/16       51      eth access down    Link not connected          10G(D) --
Port-channel VLAN    Type Mode   Status Reason                    Speed   Protocol
Interface
Po1          51      eth access up      none                      a-1000(D) lacp
Port   VRF          Status IP Address                              Speed    MTU
mgmt0 --           up     192.168.52.4                            100      1500
ISC5548B# show interface ethernet 1/3
Ethernet1/3 is up
Dedicated Interface
Hardware: 1000/10000 Ethernet, address: 8c60.4f49.818a (bia 8c60.4f49.818a)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
full-duplex, 1000 Mb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 1d02h
Last clearing of "show interface" counters 1d20h
30 seconds input rate 0 bits/sec, 0 packets/sec
30 seconds output rate 304 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 0 bps, 0 pps; output rate 200 bps, 0 pps
RX
    0 unicast packets 0 multicast packets 0 broadcast packets
    0 input packets 0 bytes
    0 jumbo packets 0 storm suppression bytes
    0 runts 0 giants 0 CRC 0 no buffer
    0 input error 0 short frame 0 overrun   0 underrun 0 ignored
    0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    202 unicast packets 87027 multicast packets 1077 broadcast packets
    88306 output packets 7601016 bytes
    0 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble 0 output discard
    0 Tx pause
4 interface resets
ISC5548B# show interface ethernet 2/1
Ethernet2/1 is up
Dedicated Interface
Hardware: 1000/10000 Ethernet, address: 8c60.4f23.5de0 (bia 8c60.4f23.5de0)
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
full-duplex, 10 Gb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 1d20h
Last clearing of "show interface" counters never
30 seconds input rate 0 bits/sec, 0 packets/sec
30 seconds output rate 312 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 0 bps, 0 pps; output rate 200 bps, 0 pps
RX
    285 unicast packets 0 multicast packets 218 broadcast packets
    503 input packets 32724 bytes
    0 jumbo packets 0 storm suppression bytes
    0 runts 0 giants 0 CRC 0 no buffer
    0 input error 0 short frame 0 overrun   0 underrun 0 ignored
    0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    406 unicast packets 89109 multicast packets 1077 broadcast packets
    90592 output packets 7827146 bytes
    0 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble 0 output discard
    0 Tx pause
1 interface resets

I have a laptop connected to a port on the switch and I am currently adding a SUSE 11 SP2 to another port that has a 10G card for a NIC. Once I finished the install I will post more specific tests using ping and SSH to illustrate.
Here is the output you requested.
ISC5548B# show port-channel summary
Flags: D - Down        P - Up in port-channel (members)
        I - Individual H - Hot-standby (LACP only)
        s - Suspended   r - Module-removed
        S - Switched    R - Routed
        U - Up (port-channel)
        M - Not in use. Min-links not met
Group Port-       Type     Protocol Member Ports
      Channel
1     Po1(SU)     Eth      LACP      Eth1/1(P)    Eth1/2(P)
ISC5548B# sh int po1
port-channel1 is up
Hardware: Port-Channel, address: 8c60.4f49.8188 (bia 8c60.4f49.8188)
MTU 1500 bytes, BW 2000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
full-duplex, 1000 Mb/s
Input flow-control is off, output flow-control is off
Switchport monitor is off
EtherType is 0x8100
Members in this channel: Eth1/1, Eth1/2
Last clearing of "show interface" counters never
30 seconds input rate 560 bits/sec, 0 packets/sec
30 seconds output rate 3064 bits/sec, 2 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 128 bps, 0 pps; output rate 2.74 Kbps, 2 pps
RX
    578695 unicast packets 11167 multicast packets 1056 broadcast packets
    590918 input packets 760063851 bytes
    0 jumbo packets 0 storm suppression bytes
    0 runts 0 giants 0 CRC 0 no buffer
    0 input error 0 short frame 0 overrun   0 underrun 0 ignored
    0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    392417 unicast packets 434693 multicast packets 2984 broadcast packets
    830094 output packets 320257324 bytes
    0 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble 0 output discard
    0 Tx pause
1 interface resets

Nexus 5548UP Downgrade from 5.1.3.N1.1 to 5.0.3.N2.2b fails -- SRG file not present/cannot be opened

Similar Messages

Maybe you are looking for