NI 6534 fails resource test.

The 6534 fails the 'resources test' under MAX.
Nothing is connected to the board. Board otherwise
seems to be producing NT crashes when used.
Any clues?
Thanks,
Scott
Details:
Error Message: The device is not responding to the
selected base address.
NI 6534 PCI form factor
Measurement Explorer 2.0.3.6
Windows NT V 4.0 SP 6
SBC is a ROBO-678 from Portwell.

Hello;
This is pretty much looking like a hardware failure. One last test you can do before point the finger to the hardware is to do a fresh installation of NI-DAQ, on another machine (W98 or W2000 if possible), install the board and run MAX.
If the same behavior shows, the board is most likely bad, otherwise, you can try uninstall and reinstall the NI-DAQ driver on the machine which is presenting the problem.
Hope this helps.
Filipe A.
Applications Engineer
National Instruments

Similar Messages

PCI-6052E resource test fails at startup

Hello,
I am using a PCI-6052E board on an XP machine. The driver is 1.8.2.f0 and MAX version is 3.1.0.3021.
Every time I boot the system, the resource test in MAX fails: the DMA resources do not appear. The board must be reinitialized manually in MAX or through the DAQmxResetDevice function in any program. This works always well and the board can then be used properly.
I would appreciate very much any hint on how to have my board fully ready at startup.
Thanks a lot.
Pascal.

Hello PascalP,
I have first some questions :
What do you mean when you say : "The driver is 1.8.2.f0 "?
Do you receive code error? If yes, can you please send it?
Please do the following:
1) When you boot your PC, launch Measurement and Automation Explorer (MAX). Under devices and interfaces -> Traditional NI-DAQ Devices, right-click on your PCI-6052 and select Properties. Note how many DMA channels are assigned to your board (may have up to 3 channels). Click Test Resources. If the device fails, please continue with (2); otherwise, open up a Test Panel and verify that it works. Then close out of MAX and try running the examples that uses the device to see if you still have the error. If you still see the error, please let me know.
2) The device is not installed properly. Shutdown the computer, remove the card and reboot. Power down again, add the card, and power up the computer. If it still fails in MAX, continue to 3.
3) Try switching PCI slots. You may also need to uninstall and reinstall the driver. Be sure to remove the hardware anytime you remove the driver.
4) Try installing the driver and then adding the card on a different computer.
If after all of this you still have trouble, please let me know what has failed and what operating system you are using and give me more information about you PC.
Hope this helps.
Sanaa TAZI
National Instruments France
Sanaa T.
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
>> http://www.nidays.fr/images/081110_ban_nidays09_468X60.gif

Mprotect failed: Resource temporarily unavailable error while starting JVM

Hi All,
I am using JDK 1.6.0_21 in sunos on sparc server.
JDK_
java version "1.6.0_21"
Java(TM) SE Runtime Environment (build 1.6.0_21-b07)
Java HotSpot(TM) Server VM (build 17.0-b17, mixed mode)
OS and Hardware config_
SunOS 5.10 Generic_142900-11 sun4u sparc SUNW,SPARC-Enterprise.
while starting the JVM getting the mprotect error as shown below:
*# V [libjvm.so+0x16af10] int frame::interpreter_frame_bci()const+0x14*
*# An error report file with more information is saved as:*
*# /progs/spider/runtime/testtool/hs_err_pid11769.log*
*# If you would like to submit a bug report, please visit:*
*# http://java.sun.com/webapps/bugreport/crash.jsp*
*11769 Abort - core dumped*
dl failure on line 685Error: failed /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/server/libjvm.so, because ld.so.1: java: fatal: /usr/jdk/instanes/jdk1.6.0/jre/lib/sparc/server/libjvm.so: mprotect failed: Resource temporarily unavailable
Complete error written to */progs/spider/runtime/testtool/hs_err_pid11769.log*.
*# A fatal error has been detected by the Java Runtime Environment:*
*# SIGSEGV (0xb) at pc=0xfe56af10, pid=11769, tid=5*
*# JRE version: 6.0_35-b10*
*# Java VM: Java HotSpot(TM) Server VM (20.10-b01 mixed mode solaris-sparc )*
*# Problematic frame:*
*# V [libjvm.so+0x16af10] int frame::interpreter_frame_bci()const+0x14*
*# If you would like to submit a bug report, please visit:*
*# http://java.sun.com/webapps/bugreport/crash.jsp*
--------------- T H R E A D ---------------
*Current thread (0x000e1400): VMThread [stack: 0xd7500000,0xd7580000] [id=5]*
siginfo:si_signo=SIGSEGV: si_errno=0, si_code=1 (SEGV_MAPERR), si_addr=0xf24ff724
Registers:
G1=0x000504b8 G2=0xfc004fc0 G3=0xfc00d6ac G4=0xfc031fc0
G5=0x0002d000 G6=0x00000000 G7=0xfe3c1a00 Y=0x00000000
O0=0xd757f5f0 O1=0xf24ff720 O2=0xfee237bc O3=0x0000ffff
O4=0x0000fc00 O5=0xfc004f88 O6=0xd757f4b8 O7=0xfe8b978c
L0=0x00041400 L1=0xfee375e8 L2=0x04000000 L3=0x00041400
L4=0x000415f0 L5=0x00041400 L6=0x000415e8 L7=0x01000000
I0=0xd757f5f0 I1=0xfee2fa94 I2=0xfedf6000 I3=0x00039a94
I4=0x0053c690 I5=0xf24ff720 I6=0xd757f518 I7=0xfe5d6b58
PC=0xfe56af10 nPC=0xfe56af14
Top of Stack: (sp=0xd757f4b8)
*0xd757f4b8: 00041400 fee375e8 04000000 00041400*
*0xd757f4c8: 000415f0 00041400 000415e8 01000000*
*0xd757f4d8: d757f5f0 fee2fa94 fedf6000 00039a94*
*0xd757f4e8: 0053c690 f24ff720 d757f518 fe5d6b58*
*0xd757f4f8: 00000000 00000000 f1b78050 00000003*
*0xd757f508: 000d0374 fffffffd 00000000 000ad1f8*
*0xd757f518: 00000000 fc004f88 fc00d6ac f24ff720*
*0xd757f528: 00000000 00704518 00000003 d757f830*
Instructions: (pc=0xfe56af10)
*0xfe56aef0: e6 26 24 50 81 c7 e0 08 81 e8 20 00 9d e3 bf a0*
*0xfe56af00: fa 06 20 00 19 00 00 3f 90 10 00 18 96 03 23 ff*
*0xfe56af10: f2 07 60 04 9f 3e 60 00 94 22 c0 0f b9 33 f0 3f*
*0xfe56af20: b7 32 b0 3f b0 1f 20 01 b4 1e e0 01 ae 0e 00 1a*
Register to memory mapping:
G1=0x000504b8 is an unknown value
G2=0xfc004fc0 is pointing into interpreter code (not bytecode specific)
G3=0xfc00d6ac is an Interpreter codelet
method entry point (kind = native) [0xfc00d560, 0xfc00d8e0] 896 bytes
G4=0xfc031fc0 is an unknown value
G5=0x0002d000 is an unknown value
G6=0x00000000 is an unknown value
G7=0xfe3c1a00 is an unknown value
O0=0xd757f5f0 is an unknown value
O1=0xf24ff720 is an unallocated location in the heap
O2=0xfee237bc: +0x2cc3c in /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/server/libjvm.so at 0xfe400000
O3=0x0000ffff is an unknown value
O4=0x0000fc00 is an unknown value
*O5=0xfc004f88 [CodeBlob (0xfc004f88)]*
Framesize: 0
BufferBlob (0xfc004f88) used for Interpreter
O6=0xd757f4b8 is an unknown value
O7=0xfe8b978c: AsyncGetCallTrace+0x96fc in /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/server/libjvm.so at 0xfe400000
L0=0x00041400 is an unknown value
L1=0xfee375e8: +0x40a68 in /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/server/libjvm.so at 0xfe400000
L2=0x04000000 is an unknown value
L3=0x00041400 is an unknown value
L4=0x000415f0 is an unknown value
L5=0x00041400 is an unknown value
L6=0x000415e8 is an unknown value
L7=0x01000000 is an unknown value
I0=0xd757f5f0 is an unknown value
I1=0xfee2fa94: +0x38f14 in /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/server/libjvm.so at 0xfe400000
*I2=0xfedf6000: GLOBALOFFSET_TABLE_+0 in /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/server/libjvm.so at 0xfe400000*
I3=0x00039a94 is an unknown value
I4=0x0053c690 is an unknown value
I5=0xf24ff720 is an unallocated location in the heap
I6=0xd757f518 is an unknown value
I7=0xfe5d6b58: JVM_GetClassLoader+0x3ec0 in /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/server/libjvm.so at 0xfe400000
Stack: [0xd7500000,0xd7580000], sp=0xd757f4b8, free space=509k
Native frames: (J=compiled Java code, j=interpreted, Vv=VM code, C=native code)
*V [libjvm.so+0x16af10] int frame::interpreter_frame_bci()const+0x14*
*V [libjvm.so+0x1d6b60] void frame::gc_prologue()+0x20*
*V [libjvm.so+0x2241e4] void Threads::gc_prologue()+0xd0*
*V [libjvm.so+0x7c62c8] void PSMarkSweep::invoke_no_policy(bool)+0x52c*
*V [libjvm.so+0x7c5d78] void PSMarkSweep::invoke(bool)+0x8c*
*V [libjvm.so+0x225264] void VM_ParallelGCSystemGC::doit()+0xc4*
*V [libjvm.so+0x1f0018] void VM_Operation::evaluate()+0x88*
*V [libjvm.so+0x8ce23c] void VMThread::evaluate_operation(VM_Operation*)+0xd4*
*V [libjvm.so+0x8ce784] void VMThread::loop()+0x414*
*V [libjvm.so+0x267010] void VMThread::run()+0xa0*
*V [libjvm.so+0x791a18] java_start+0x158*
VM_Operation (0xf24ff5b0):
*[error occurred during error reporting (printing VM operation), id 0xb]*
--------------- P R O C E S S ---------------
Java Threads: ( => current thread )
*0x00704400 JavaThread "GC Daemon" daemon [_thread_blocked, id=20, stack(0xf2480000,0xf2500000)]*
*0x00716400 JavaThread "RMI Reaper" [_thread_blocked, id=19, stack(0xf2580000,0xf2600000)]*
*0x0070fc00 JavaThread "RMI TCP Accept-0" daemon [_thread_in_native, id=18, stack(0xf2680000,0xf2700000)]*
*0x00100800 JavaThread "Low Memory Detector" daemon [_thread_blocked, id=11, stack(0xd6f00000,0xd6f80000)]*
*0x000fe000 JavaThread "C2 CompilerThread1" daemon [_thread_blocked, id=10, stack(0xd7000000,0xd7080000)]*
*0x000fb800 JavaThread "C2 CompilerThread0" daemon [_thread_blocked, id=9, stack(0xd7100000,0xd7180000)]*
*0x000fa000 JavaThread "Signal Dispatcher" daemon [_thread_blocked, id=8, stack(0xd7200000,0xd7280000)]*
*0x000e6c00 JavaThread "Finalizer" daemon [_thread_blocked, id=7, stack(0xd7300000,0xd7380000)]*
*0x000e5400 JavaThread "Reference Handler" daemon [_thread_blocked, id=6, stack(0xd7400000,0xd7480000)]*
*0x00032000 JavaThread "main" [_thread_blocked, id=2, stack(0xfe300000,0xfe380000)]*
Other Threads:
*=>0x000e1400 VMThread [stack: 0xd7500000,0xd7580000] [id=5]*
*0x00113400 WatcherThread [stack: 0xd6e00000,0xd6e80000] [id=12]*
VM state:at safepoint (normal execution)
*VM Mutex/Monitor currently owned by a thread: ([mutex/lock_event])*
*[0x00031330] Threads_lock - owner thread: 0x000e1400*
*[0x00031740] Heap_lock - owner thread: 0x00704400*
Heap
PSYoungGen      total 10752K, used 1008K [0xf1000000, 0xf1c00000, 0xfbc00000)
eden space 9216K, 0% used [0xf1000000,0xf1000000,0xf1900000)
from space 1536K, 65% used [0xf1a80000,0xf1b7c050,0xf1c00000)
to   space 1536K, 0% used [0xf1900000,0xf1900000,0xf1a80000)
PSOldGen        total 24576K, used 0K [0xdb800000, 0xdd000000, 0xf1000000)
object space 24576K, 0% used [0xdb800000,0xdb800000,0xdd000000)
PSPermGen       total 16384K, used 7578K [0xd7800000, 0xd8800000, 0xdb800000)
object space 16384K, 46% used [0xd7800000,0xd7f669c8,0xd8800000)
Code Cache [0xfc000000, 0xfc400000, 0xfe000000)
total_blobs=188 nmethods=49 adapters=95 free_code_cache=33095232 largest_free_block=26368
Dynamic libraries:
*0x00010000 /usr/jdk/instances/jdk1.6.0/jre/bin/java*
*0xff3a0000 /usr/lib/lwp/libthread.so.1*
*0xff370000 /usr/jdk/instances/jdk1.6.0/jre/bin/../lib/sparc/jli/libjli.so*
*0xff350000 /lib/libdl.so.1*
*0xff200000 /lib/libc.so.1*
*0xff390000 /platform/SUNW,SPARC-Enterprise/lib/libc_psr.so.1*
*0xfe400000 /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/server/libjvm.so*
*0xff1d0000 /lib/libsocket.so.1*
*0xff1f0000 /usr/lib/libsched.so.1*
*0xff1b0000 /lib/libm.so.1*
*0xff180000 /usr/lib/libCrun.so.1*
*0xff160000 /lib/libdoor.so.1*
*0xff120000 /usr/lib/libdemangle.so.1*
*0xff100000 /lib/libkstat.so.1*
*0xff000000 /lib/libnsl.so.1*
*0xfef00000 /lib/libm.so.2*
*0xff0c0000 /lib/libscf.so.1*
*0xfefe0000 /lib/libuutil.so.1*
*0xfeee0000 /lib/libgen.so.1*
*0xfeeb0000 /lib/libmd.so.1*
*0xfee90000 /lib/libmp.so.2*
*0xfe390000 /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/libverify.so*
*0xfe2c0000 /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/libjava.so*
*0xfe280000 /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/libzip.so*
*0xfe260000 /usr/lib/locale/no_NO.ISO8859-1@bokmal/[email protected]*
*0xfbfc0000 /progs/spider/TIBCO/tibrv/8.3/lib/libtibrvj.so*
*0xfbe60000 /progs/spider/TIBCO/tibrv/8.3/lib/libtibrvcmq.so*
*0xfbe30000 /progs/spider/TIBCO/tibrv/8.3/lib/libtibrvcm.so*
*0xfbe10000 /progs/spider/TIBCO/tibrv/8.3/lib/libtibrvft.so*
*0xd6d80000 /progs/spider/TIBCO/tibrv/8.3/lib/libtibrv.so*
*0xfbfe0000 /lib/libpthread.so.1*
*0xfbd40000 /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/libmanagement.so*
*0xfbd10000 /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/libj2pkcs11.so*
*0xfbc40000 /usr/lib/libpkcs11.so*
*0xfbc20000 /usr/lib/libcryptoutil.so.1*
*0xf27a0000 /usr/lib/security/pkcs11_softtoken.so*
*0xf2770000 /usr/jdk/instances/jdk1.6.0/jre/lib/sparc/libnet.so*
VM Arguments:
jvm_args: -Dlog.dir=/data/flowlogs/testtool -Djava.rmi.server.codebase=file:///progs/spider/flow_home/Output/java/classes/ -Djava.security.policy=/progs/spider/flow_home/config/flow2/props/java.policy -Dproperty_file=testtool.properties -Dtestdata=/progs/spider/flow_home/test/framework/testtool
java_command: flow.framework.componentserver.Server
Launcher Type: SUN_STANDARD
Environment Variables:
JAVA_HOME=/usr/jdk/jdk1.6.0_35
PATH=/progs/spider/flow_home/bin:/progs/spider/flow_home/ant/bin:/usr/jdk/jdk1.6.0_35/bin:/usr/jdk/jdk1.6.0_35/jre/bin:/usr/bin:/usr/local/bin:/progs/spider/TIBCO/tibrv/8.3/bin:/progs/spider/TIBCO/inconcert/server/ICFLOWNEWUTV/bin
LD_LIBRARY_PATH=/usr/jdk/instances/jdk1.6.0/jre/lib/sparc/server:/usr/jdk/instances/jdk1.6.0/jre/lib/sparc:/usr/jdk/instances/jdk1.6.0/jre/../lib/sparc::/usr/lib/lwp:/progs/spider/TIBCO/inconcert/icapps/shared/native/lib:/progs/spider/TIBCO/tibrv/8.3/lib:/progs/spider/flow_home/lib/tibco:/progs/spider/TIBCO/inconcert/icapps/icjava/lib:/progs/spider/TIBCO/inconcert/server/ICFLOWNEWUTV/lib:/progs/spider/TIBCO/tibrv/8.3/lib
SHELL=/bin/bash
Signal Handlers:
*SIGSEGV: [libjvm.so+0x8ca71c], sa_mask[0]=0xffbffeff, sa_flags=0x0000000c*
*SIGBUS: [libjvm.so+0x8ca71c], sa_mask[0]=0xffbffeff, sa_flags=0x0000000c*
*SIGFPE: [libjvm.so+0x1d0f7c], sa_mask[0]=0xffbffeff, sa_flags=0x0000000c*
SIGPIPE: SIG_IGN, sa_mask[0]=0x00000000, sa_flags=0x00000000
*SIGXFSZ: [libjvm.so+0x1d0f7c], sa_mask[0]=0xffbffeff, sa_flags=0x0000000c*
*SIGILL: [libjvm.so+0x1d0f7c], sa_mask[0]=0xffbffeff, sa_flags=0x0000000c*
SIGUSR1: SIG_DFL, sa_mask[0]=0x00000000, sa_flags=0x00000000
SIGUSR2: SIG_DFL, sa_mask[0]=0x00000000, sa_flags=0x00000000
*SIGQUIT: [libjvm.so+0x794044], sa_mask[0]=0xffbffeff, sa_flags=0x00000004*
*SIGHUP: [libjvm.so+0x794044], sa_mask[0]=0xffbffeff, sa_flags=0x00000004*
SIGINT: SIG_IGN, sa_mask[0]=0x00000000, sa_flags=0x00000000
*SIGTERM: [libjvm.so+0x794044], sa_mask[0]=0xffbffeff, sa_flags=0x00000004*
*SIG39: [libjvm.so+0x7976b8], sa_mask[0]=0x00000000, sa_flags=0x00000008*
*SIG40: [libjvm.so+0x1d0f7c], sa_mask[0]=0xffbffeff, sa_flags=0x0000000c*
--------------- S Y S T E M ---------------
OS:                      Solaris 10 10/09 s10s_u8wos_08a SPARC
Copyright 2009 Sun Microsystems, Inc. All Rights Reserved.
Use is subject to license terms.
Assembled 16 September 2009
uname:SunOS 5.10 Generic_142900-11 sun4u (T2 libthread)
rlimit: STACK 8192k, CORE 0k, NOFILE 65536, AS infinity
load average:0,82 0,83 0,60
CPU:total 2 has_v8, has_v9, popc, has_vis1, has_vis2, is_ultra3, is_sparc64
Memory: 8k page, physical 2097152k(0k free)
vm_info: Java HotSpot(TM) Server VM (20.10-b01) for solaris-sparc JRE (1.6.0_35-b10), built on Aug 28 2012 15:42:48 by "" with Workshop 5.8
time: Thu Jun 6 07:45:16 2013
elapsed time: 6 seconds
Can any one help me what is happening.
Regards,
Satya Krishna Y
Edited by: 1010262 on 06.jun.2013 07:55
Edited by: 1010262 on 06.jun.2013 07:56

> *# SIGSEGV
Common cause is JNI
> /progs/spider/TIBCO/tibrv/8.3/lib/libtibrvj.so
Looks like a non-standard library so it suggests JNI is in use

System failed memory test

I am really new to Solaris so please forgive me if I sound really dumb. I was able to install Solaris 10, turned off my computer and now all I recieve is System failed memory test. Please help have tried different memory sticks and still recieve the same message.

is this a bios message? id suggest running a mem test if this is coming before the os starts up [http://www.memtest.org/]
if you have the mother board diag tools on cd, run those as well. unless this is a sparc system?

Photoshop CC White Window Workaround Plugin Fails Version Test?

I'm sure everyone with a Wacom tablet on a Mac is aware of the "White window" issue. See the original discussion thread at: Drop Down Menus in Photoshop CS 6 Goes Blank In Mavericks
Photoshop developers partook in the discussion on the thread, and a plugin that fixed the issue was released. Plugin works great, and even in CC/CS6
With the latest update to the Photoshop CC application, the white window issue is back. Looking in the console reveals the following:
8/7/14 1:31:03.798 PM Adobe Photoshop CC 2014[11038]: WhiteWindowWorkaround failed version test (<= 14) and it will not install. Version is 15
8/7/14 1:31:03.798 PM Adobe Photoshop CC 2014[11038]: WhiteWindowWorkaround did *not* initialize
Is there an updated version/fix that anyone is aware of? I searched, but maybe I missed something.
Many thanks.
Andrew.

Photoshop CC 2014 does not need that plugin, because the workarounds are already built into the app.

865PE NEO2 FSIR fails memory tests

This is the second MB that I've had this problem with, so something is causing them to fail. Here's the story:
New install, 865PE Neo2 FSIR + P4 2.6GHz 800MHz FSB, 2 x Crucial PC3200 256MB DDR, everything seems ok, XP installs with no problems.
About a month down the road I'm plagued by sudden reboots, Microsoft Error Reporting says RAM, says to DL and run it's DOS memory check utility. I get the utility, create bootable CD and run the utility, computer fails all RAM checks. I pull each RAM stick in turn and re-run the check with each stick separately, still fails all tests. Shortly after this, the board refuses to POST. Ship the board back to New Egg for replacement.
Installed replacement MB with 4 x 256MB Crucial PC3200, Microsoft DOS memory check program passes, no problems. About 2 weeks later I run into minor instability so I run the same memory check again, the board fails all tests????? I pull all Crucial memory sticks and put in a test stick of Corsair XMS 3200; same result, failure of all memory tests.
At this point, WinXP still runs, but this is the same pattern that the other board showed, right until it quit altogether.
It occurs to me that I DID flash BIOS to 1.9 between the time I first tested the RAM and got a pass and the time I tested and got a failure, could this be a coincidence? I can't remember if I updated the BIOS on the first board or not, so this may mean nothing.
System Specs:
MSI 865PE NEO2 FSIR
P4 2.6GHz, 800MHz FSB (all defaults, no overclock, Vantec HS)
Crucial CT3264Z40B.8T PC3200, CL3 256MB (2 Modules)
Crucial CT3264Z40B.8T2 PC 3200, CL3 256MB (2 Modules)
(Tested with same results with single Corsair CMX512-3200C2PT 512MB)
Antex True Power 430W PS
ATI Radeon 9600 Pro
All PCI slots open
Seagate 120GB System drive, 7,200RPM primary master
IBM 30GB drive, 7,200RPM primary slave
LiteOn DVD ROM secondary master
Sony CDRW secondary slave
2 x IBM 30GB drives on Promise PATA.
I know I'm probably gonna have to RMA this board, but I'd really like to know what is causing this so I can avoid it next time.
If anyone has any ideas I'd sure appreciate it.
Scott

Quote
Originally posted by jwspicer
As they say - been there, done that. Always flash using DOS, and always keep backup, so I went back to the original BIOS for the board. No luck. Apparently once the screwup is done - it stays that way.
--BUT--
Suspect it is the reallocation for the P4 EE that is the issue. Reason is that Memtest86 has been running on that box for 9 hours now with NO error. However, it also shows only 104K of reserved memory. My other 865 board with onboard RAID (an ASUS P4P800 Deluxe) shows 687K reserved. So either the ASUS is wasting a lot of space, or the MIS is no longer correctly indicating the amount of memory reserved by the BIOS (including the Promise BIOS) at startup. Then Microsoft's utility is not correctly scanning. But Memtest, which probes for the "correct" setting, is. (The Memtest86 version is 3.0, and the test was done with the Promise enabled and drives attached (so the BIOS loads) and all the other setup was as it would be normally (standard IBOS options, etc.)
So who's right? And if MS' tool has the problem, does that indicate Windows XP reads memory the same way? Hmmm...
Hmm, I haven't tried reverting BIOS, but I'm typing this on the affected machine (which Memtest 86 says is fine) with only the two RAM chips it likes and so far no problems; I've run PCMark4 and 3DMark4 benchmarks all night and no problems, it was still happily churning away on 3DMark this morning. I guess either one of the Crucial sticks it doesn't like is bad or Crucial changed something in a revision to the chips it doesn't like.
Just a FYI, the Crucial sticks it DOESN'T like are CT3264Z40B.8T2
The sticks it DOES like (at slow or fast performance, forget about turbo or ultra turbo) are CT3264Z40B.8T
Both pairs are PC3200, CL3, 256MB DIMM's, single sided.
I think you're right about Microsoft's RAM tester being buggy, I can't believe ANYTHING could run if the RAM was actually giving the errors it shows, EVERY test shows things like "expected result 11111111 actual result ff1e0001" The Microsoft tester does run fine on the other 5 computers here; a mix of laptops and desktops; none using this board. It also ran on this board when it was installed, I guess the BIOS upgrade must be the cause.
Scott

Can't Create a Data Source - Failed to test connection. [DBNETLIB][ConnectionOpen (Connect()).]SQL Server does not exist or access denied

Hi there,
I am having a serious issue with The Power BI Data Management Gateway which I am hoping that someone can help me with.
Basically I am setting a connection between a Power BI demo site and a SQL 2012 Database based on Azure. The Data Management Gateway and is up and running, and Power BI has managed to connect to it successfuly.
By following the tutorials at
here I was able to successful create my Data Connection Gateway with a self-signed certificate.
However, when trying to create the data source I come into problems. The Data Source Manager manages to successfully resolve the hostname, as per the screenshot below:
Bear in mind that I exposed the require ports in Azure as endpoints and I managed to modify my hosts file on my local machine so I could access the SQL server hosted in Azure using its internal name -- otherwise I would not be able to get this far.
However the creation of the data source also fails when trying to created it whilst logged in the SQL server in question:
The Data Source Manager returns the error when using the Microsoft OLE DB Provider for SQL Server:
Failed to test connection. [DBNETLIB][ConnectionOpen (Connect()).]SQL Server does not exist or access denied
I tried using the SQL Server Native Client 11.0 instead but I also get an error. This time the error is:
Failed to test connection. Login timeout expiredA network-related or instance-specific error has occurred while establishing a connection to SQL Server. Server is not found or not accessible. Check if instance name is correct and if SQL Server is configured to allow remote connections. For more information see SQL Server Books Online.Named Pipes Provider: Could not open a connection to SQL Server [53].
Some considerations
If I provide an invalid username/password, the Data Source Manager does say that the username and password is incorrect.
Firewall is turned off in the SQL Server (either way, this error also happens if I try top use the Data Source Manager whilst logged in the SQL Server itself).
SQL Profiler does not show any attempt of connection.
The SQL server instance in question is the default one.
The error happens regardless if I select the option to encrypt connection or not.
In SQL Configuration manager I can see that all protocols are enabled (TCP/IP, Named Pipes and Shared Memory.
The Event Viewer does not provide any further errors than the one I have copied in this post.
I'm at a loss here. Could someone please advise what might I be doing wrong?
Regards,
P.

Here is what I had to do to solve this issue:
Basically I had to add the MSSQL TCP/IP port as an end-point in Azure. After I did that, then I was able to create the data-source. However, I was only able to authenticate with a SQL account, as any domain account would return me an error saying that the
domain isn't trusted.
What puzzles me here is how come the Data Source Manager would inform me that an account username/password was invalid, but it would fail/timeout if I provided valid credentials (!?!?!!?)

The requested resource (/test/) is not available. Tomcat. Myfaces.

Hi, i use Myfaces and Tomcat. Sometimes there is error : The requested resource (/test/) is not available. This is regarding war file. How can i check where there is the error? Sometimes the files are allmost same, i think. But in one time it works, in other no. I use Eclipse to edit and create files. Is it possible to check the errors before creating of war file? Thanks in advance!!!!!!!!!!

Hi, i use Myfaces and Tomcat. Sometimes there is error : The requested resource (/test/) is not available. This is regarding war file. How can i check where there is the error? Sometimes the files are allmost same, i think. But in one time it works, in other no. I use Eclipse to edit and create files. Is it possible to check the errors before creating of war file? Thanks in advance!!!!!!!!!!

Error "fork failed: Resource temporarily unavailable" when trying to login

I have a problem with a PPC-based server running OS X Server 10.4.11. Suddenly I'm unable to log in via SSH or use ARD (remote desktop) via the admin user account.
In SSH it shows "Received disconnect from 1.2.3.4: 2: fork failed: Resource temporarily unavailable" as error message.
Interestingly I can login directly via root. I wonder how to solve this, just waiting some time, rebooting server, any deeper insight would be welcome ?
Here is what "top" says:
Processes: 83 total, 2 running, 81 sleeping... 188 threads 17:07:16
Load Avg: 0.12, 0.19, 0.15 CPU usage: 0.9% user, 13.6% sys, 85.5% idle
SharedLibs: num = 173, resident = 40.6M code, 4.59M data, 6.96M LinkEdit
MemRegions: num = 6812, resident = 89.3M + 8.34M private, 70.7M shared
PhysMem: 98.0M wired, 123M active, 637M inactive, 858M used, 165M free
VM: 3.41G + 113M 5641936(0) pageins, 33735(0) pageouts
PID COMMAND %CPU TIME #TH #PRTS #MREGS RPRVT RSHRD RSIZE VSIZE
20343 AppleVNCSe 0.0% 0:00.06 4 64 51 532K 3.84M 1.76M 33.4M
20338 ARDAgent 0.0% 0:00.36 6 96 76 1.03M 4.34M 2.51M 52.5M
20334 SecurityAg 0.1% 1:21.31 1 68 102 1.63M 16.4M 8.77M 76.9M
20333 authorizat 0.0% 0:00.04 1 31 28 364K 708K 1.20M 27.4M
20332 mcxd 0.0% 0:02.61 1 40 40 604K 7.01M 2.24M 40.3M
20326 WindowServ 0.0% 0:31.07 2 66 45 468K 7.70M 8.21M 63.2M
20321 loginwindo 0.0% 0:00.19 3 94 99 972K 7.72M 3.22M 61.0M
20010 upsd 0.0% 0:23.23 1 36 36 3.80M 732K 3.96M 30.9M
18075 top 8.8% 0:00.44 1 19 22 824K 316K 1.23M 27.0M
18070 perl 4.0% 0:00.91 1 10 155 15.4M+ 38.5M 27.1M+ 63.9M-
18058 perl 0.0% 0:01.40 1 10 155 15.7M 38.5M 27.2M 63.9M
18045 bounce 0.0% 0:00.01 1 16 20 192K 392K 740K 26.8M
18021 smtp 0.0% 0:00.01 1 16 20 208K 452K 804K 26.8M
18020 smtp 0.0% 0:00.01 1 16 20 212K 452K 812K 26.8M
18004 smtp 0.0% 0:00.03 1 16 20 220K 452K 624K 26.8M
17962 smtpd 0.0% 0:00.08 1 22 80 740K 1.45M 2.30M 29.7M
17858 sh 0.0% 0:00.01 1 14 17 196K 764K 820K 27.2M
17843 sshd 0.0% 0:00.09 1 16 42 532K 936K 1.36M 30.0M
17832 proxymap 0.0% 0:00.01 1 16 20 200K 356K 692K 26.7M
17712 smtpd 0.0% 0:00.12 1 22 80 760K 1.45M 2.31M 29.7M
17214 cleanup 0.0% 0:00.13 1 16 20 208K 412K 764K 26.8M
17211 cleanup 0.0% 0:00.13 1 16 20 208K 412K 764K 26.8M
16232 smtpd 0.0% 0:00.23 1 22 80 784K 1.45M 2.34M 29.7M
16231 smtpd 0.0% 0:00.25 1 22 80 784K 1.45M 2.34M 29.7M
16221 smtpd 0.0% 0:00.23 1 22 80 788K 1.45M 2.34M 29.7M
16220 smtpd 0.0% 0:00.27 1 24 80 892K 1.45M 2.43M 29.7M
15845 pickup 0.0% 0:00.02 1 16 20 188K 368K 692K 26.7M
14736 named 0.0% 0:45.48 1 14 25 1.28M 1.46M 2.55M 84.4M
14153 trivial-re 0.0% 0:00.97 1 16 20 244K 380K 756K 26.7M
12301 cupsd 0.0% 0:00.41 2 30 26 280K 636K 924K 27.8M
6814 master 0.0% 0:15.99 1 16 20 220K 296K 584K 26.7M
6807 qmgr 0.0% 4:29.58 1 16 20 516K 396K 1.00M 26.8M
6804 master 0.2% 5:25.26 1 15 20 208K+ 340K 652K+ 26.7M
6791 perl 0.0% 1:30.19 1 15 154 360K 38.5M 19.9M 64.7M
2358 trivial-re 0.0% 0:04.52 1 16 20 384K 380K 892K 26.7M
735 httpd 0.0% 0:35.78 1 12 110 584K 1.80M 1.96M 31.3M
734 httpd 0.0% 0:36.17 1 12 111 592K 1.80M 1.80M 31.3M
733 httpd 0.0% 0:35.51 1 12 110 560K 1.80M 1.91M 31.3M
636 dccifd 0.0% 0:37.46 3 30 27 88K 336K 224K 34.4M
635 dccifd 0.0% 0:00.00 1 8 17 0K 332K 80K 27.2M
373 httpd 0.0% 0:36.51 1 12 111 564K 1.80M 1.91M 31.3M
324 ipfwlogger 0.0% 0:08.18 1 10 18 36K 236K 124K 26.6M
292 httpd 0.0% 0:36.63 1 11 111 540K 1.80M 1.87M 31.3M
283 personalba 0.0% 0:10.65 1 76 45 520K 4.04M 1.60M 38.1M
277 httpd 0.0% 0:53.49 1 9 110 104K 1.80M 1.12M 32.2M
259 mds 0.0% 2:19.01 7 81 52 576K 4.07M 1.54M 41.8M
255 ARDHelper 0.0% 1:04.73 1 9 17 28K 236K 120K 26.6M
251 getty 0.0% 0:00.00 1 14 18 4K 228K 196K 26.6M
236 serialnumb 0.0% 0:29.85 3 27 33 240K 548K 848K 28.3M

Just noticed that this is still open... a reboot did it
However maybe someone has an idea how this happened and how to prevent similar situations in the future, if possible ?

[svn:bz-trunk] 16330: QA: Yes - Ran test locally and it was failing but tested condition was true - there is no services-config .xml file

Revision: 16330
Revision: 16330
Author:   [email protected]
Date:     2010-05-26 07:55:41 -0700 (Wed, 26 May 2010)
Log Message:
QA: Yes - Ran test locally and it was failing but tested condition was true - there is no services-config.xml file
Doc: No
Checkintests: NA
Details: Updated expected error message to match current error.
Modified Paths:
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/NoServicesConfigFileTest/error.t xt

I have uploaded detail.txt at below url.
http://m.uploadedit.com/b041/1413264342685.txt
Hi Mahesh,
According to log file, I find the message ‘The setup100.exe.config file was not found, therefore the DTSWizard and SQLWatson app config files were not replaced’. It seems that the SQL Server setup file is not complete. Please check that if the SQL Server
setup file is corrupted, if it is corrupted, please download it again and reinstall SQL Server 2008 R2.
However, if there’s no problem with the setup file, please check that if there is third-party software such as anti-virus software on your computer blocking the process of SQL Server installation. In addition, make sure that you choose ‘Run as administrator’
to launch the setup and configure SQL Server service accounts appropriately with administrator permission during the installation.
For more details about this error, please review the following similar thread.
http://answers.flyppdevportal.com/categories/sqlserver/sqlsetupandupgrade.aspx?ID=ad794a97-09ae-4aae-9d68-0b06f9af3e16
Thanks,
Lydia Zhang

RPE-02085: Failed to test wb_rti_workflow_util.initialize

Hi,
I'm getting the below error when i try to deploy process flow via deployment manager.
RPE-02085: Failed to test wb_rti_workflow_util.initialize through deployed Workflow Database Link ORCL@WB_LK_LD_INV. Please check that "EXECUTE ANY PROCEDURE" privilege is set and that the OWB Runtime is available.
- ORA-04052: error occurred when looking up remote object RUNTIME_OWNER.WB_RTI_WORKFLOW_UTIL@ORCL@WB_LK_LD_INV
ORA-12545: Connect failed because target host or object does not exist
What would be the cause?
I'm exactly following the toturial which given by http://www.oracle.com/technology/obe/obe_bi/index.html
Even I have given grant EXECUTE ANY PROCEDURE to owf_mgr but still i'm getting the same error.
Please help me...
Below is the details of my installation:
Database : 10.1.0.2.0
OWB: 10.1.0.2.0
OWF: 2.6.3
Thanks
Raj Kumar

U need to login into repository owner and grant the all privilages on wb_rti_workflow_util package to your user ( owf_mgr , in ur case)
in short
grant all on wb_rti_workflow_util to owf_mgr ( u need to type this command from repository owner login )
Nikita

HTML generated by Flash failed validation test

Hello guys,
I have created a simple Flash website:
http://www.icebergfilms.com
It's HTML was also created in Flash using Publish Settings. However, when I tried to validate this HTML using online validator, it failed the test:
http://validator.w3.org/check?uri=http%3A%2F%2Fwww.icebergfilms.com%2F&charset=%28detect+a utomatically%29&doctype=Inline&group=0&No200=1&verbose=1&user-agent=W3C_Validator%2F1.654
I am a complete novice in Flash and in HTML, so could please anyone give me some advise how to fix this?
Thank you so much for your help.

Thank you so much for your response.
I actually did try (with help of some guys from html forum) to use text editor to generate HTML and simply just embed that swf file onto that HTML document.
It works well, but there is one little problem. Very first thing viewer see (after clicking on URL to upload my site) is black background with
white rectangle which is the space where swf movie will appear. It last around 2-3 seconds. Then preloader appears and everything goes normal. But this white empty space before preloader shows up is very weird.
here is that code:
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01//EN"
   "http://www.w3.org/TR/html4/strict.dtd">
<html lang="en">
<head>
<base href="http://www.icebergfilms.com/">
<meta http-equiv="Content-Type" content="text/html; charset=iso-8859-1">
<meta name="language" content="english">
<meta http-equiv="Content-Style-Type" content="text/css">
<meta name="Subject" content="IcebergFilms specializes in promotional videos and demos, environmental projects, adventure documentaries, live sport events, corporate and training videos and videos for fundraising presentations.">
<meta name="Description" content="IcebergFilms is a local video production company located in Vancouver BC specializing in promotional videos, adventure documentaries, training and educational videos, demo reels, live sport evets, videos for fundraising presentations, etc.">
<meta name="Keywords" content="video production in Vancouver, videographer in Vancouver, video production services, professional, editing, promotional, demo, film, educauional, outdoors, expeditions, documentaries, corporate, dvd, hdv, hd, advertising, environmental, video stock footage, fundraising, high definition, nature, digital, live events, sport, kayaking, hiking, trekking, biking, training, final cut pro, videographer for hire, vancouver, bc, canada">
<meta content="General" name="rating">
<meta content="index,follow" name="robots">
<meta content="ALL" name="robots">
<meta content="5 days" name="revisit-after">
<title>>Promotional Video Production company in Vancouver - IcebergFilms</title>
<style type="text/css">
body {
    background-color:#000;
object {
    display:block;
    margin:auto;
</style>
</head>
<body>
<div>
<object type="application/x-shockwave-flash" data="IcebergFilms.swf" width="810" height="600">
<param name="movie" value="IcebergFilms.swf">
<param name="play" value="true">
<param name="loop" value="true">
<param name="quality" value="high">
</object>
</div>
</body>
</html>
This white space does not happened when using HTML generated by Flash, however, that one on the other hand misses some basic elements.
Should I then maybe just use the code above , delete this BODY sectiont:
<div>
<object type="application/x-shockwave-flash" data="IcebergFilms.swf" width="810" height="600">
<param name="movie" value="IcebergFilms.swf">
<param name="play" value="true">
<param name="loop" value="true">
<param name="quality" value="high">
</object>
</div>
and replace it with BODY section from Flash generated HTML?
I apologize for this chaotic post, but I am trying to create the correct code for about 2 weeks now, and I am starting to lose it
Thanks again for your response .... and for your patience.

Battery on iPhone 5 failed the test: Battery replacement or external battery? NEED HELP

Apple ran the test for me, and it shows that my iPhone 5 battery failed the test.
Therefore, I need to get a battery replacement to solve the problem.
I don't want to pay for $79 + tax to get it fix though. Another way I could think of would be getting an external battery pack.
It could cost around $40 (I will try to find it cheaper).
So, which way will last my phone longer?
Which way you recommended?
P.S. I planned to use this phone until it breaks down! Therefore, I need to find the solution that will last my phone long.
PLEASE PLEASE PLEASE, DO NOT tell me the ways to extend the battery life.
I tried every single way, but NONE WORKED!
Let me know,
Thanks

Iphones are not user serviceable.
By opening the device you have voided all rights to warranty and support from Apple.

[svn:bz-trunk] 18907: Fix failing MBean test.

Revision: 18907
Revision: 18907
Author:   [email protected]
Date:     2010-12-01 11:55:22 -0800 (Wed, 01 Dec 2010)
Log Message:
Fix failing MBean test. The name of the web application changed in the web.xml file for the webapp causing the test to break. I updated the test to use the new webapp name which is "Flex QA Web Application". There are a few more MBean tests that are failing likely due to the same problem. I will update these as I have time unless someone else wants to tackle this.
Modified Paths:
    blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/MBean/jmx/MBeanServerGateway.mxm l

Pierre-Charles David a écrit :
> Hi,
>
> I've got a very strange issue and I don't know where to look for to fix
> it. In some Eclipse configuration I use, SWTBot does not work at all: it
> fails the very first method with a WidgetNotFoundException.
[snip]
Well, I found the issue:
SWTBot declares a dependency to org.apache.log4j but does not indicate
any specific version. However, it uses APIs which only appeared in log4j
1.2.12 (at least Logger.trace(), maybe others).
In the Eclipse installation I have which did not work ("Topcased RCP"),
there was a bundle which provided the org.apache.log4j package, but
using log4j version 1.2.8. As it happens, Eclipse decided to provide
this one to SWTBot instead of other versions available from different
bundles (1.2.12 and 1.2.15). The test failed with an internal
NoSuchMethodError, which must have been caught by some code and wrapped
as the WidgetNotFoundException I saw.
Removing the plugin with log4j 1.2.8 from the test's run configuration
solves the issue.
I have opened bug #286527 about this.

[svn:bz-trunk] 7681: Fix bunch of failing config tests on BlazeDS/ trunk by removing javax.servlet. UnavailableException from the expected error string.

Revision: 7681
Author:   [email protected]
Date:     2009-06-09 11:44:36 -0700 (Tue, 09 Jun 2009)
Log Message:
Fix bunch of failing config tests on BlazeDS/trunk by removing javax.servlet.UnavailableException from the expected error string.
Modified Paths:
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/destination/IncorrectRootElement Test/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/AdaptiveServerT oClient/AdaptiveFrequencyTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/AdaptiveServerT oClient/FrequencyStepSizeTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/AdaptiveServerT oClient/MaxQueueSizeTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/DestinationWith NoChannelTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/DestinationWith NoIDTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/jms/InvalidAckn owledgeModeTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/jms/InvalidDeli veryModeTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/jms/InvalidDest inationTypeTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/jms/InvalidMess ageTypeTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/jms/NoConnectio nFactoryTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/jms/NoJNDINameT est/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/throttle/thrott leInbound/InvalidBufferPolicyTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/throttle/thrott leInbound/InvalidConflatePolicyTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/throttle/thrott leInbound/UnknownInboundPolicyTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/throttle/thrott leInbound/frequencies/McfGreaterthanMfTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/throttle/thrott leOutbound/InvalidBufferPolicyTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/throttle/thrott leOutbound/InvalidConflatePolicyTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/throttle/thrott leOutbound/InvalidErrorPolicyTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/throttle/thrott leOutbound/UnknownOutboundPolicyTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/throttle/thrott leOutbound/frequencies/McfGreaterthanMfTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/validation/nonE xistingValidatorTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/validation/same ExplicitTypeValidatorTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/validation/same TypeValidatorTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/validation/wron gTypeValidatorTest/error.txt

NI 6534 fails resource test.

Similar Messages

Maybe you are looking for