NI MAX throughput error and Camera attribute out of range

I recently purchased a Point Grey Grasshopper3 camera, it seems to work fine in the Fly Cap software point grey provides, but I get an error in NI MAX when I try to do a simple grab (shown below). This error shows up every time I try to grab an image the first time after opening NI MAX, even though throughput is set to the max. Then I change the throughput max under device control to any number around the max of 125000000, and the camera works fine for MAX. It will grab images as much as I need. Then I save the camera, exit MAX, open MAX again, it shows my saved settings, I go to grab images and I get the error again. So I change the range to whatever number and it works again in the same session in MAX. 
I did have a point grey Zebra2 working fine, and was using it in my LabVIEW program with IMAQdx to acquire images. When I try to use grasshopper3, LabVIEW returns an error of camera attribute out of range from the camera configuration VI. The VI's I am using to test the camera is just open camera, configure acquisition, start acquisition, get image, unconfigure acquisition, and close camera from IMAQdx. I did twice open MAX, change throughput, save camera, close MAX without grabbing an image, and then was able to acquire images in LabVIEW on the first run. Then I would run the VI again and it would return the error for camera attribute out of range. I have changed the packet size, resolution, and frame rate of the camera with out noticing a difference in the errors. 
Since I am able to stream images from the camera in point greys fly capture, and in MAX after toggling the throughput setting, it leads me to believe there is some sort of MAX/LabVIEW error preventing me from capturing the images.
Any ideas? Has anyone else had this issue with MAX and LV? 
Solved!
Go to Solution.
Attachments:
MAX error.png ‏17 KB

It looks like Point Grey cameras have shown this error before based on out of date firmware. See this link for one such instance. I would monitor the camera file (*.icd) located in the IMAQdx data folder in Public Documents to see if the actual value is being overwritten after the camera configuration is saved in MAX. There is a chance that the GigE .XML file that is transferred from the camera is overwriting these values to the unacceptable value. See this link for a KB regarding this error, which leads me to believe this may be the issue.
Karl G.
Applications Engineer
ni.com/support

Similar Messages

  • Attribute out of range error with Dalsa Spyder camera

    I have a Dalsa Spyder camera SG-11 which seems to work fine in NI MAX. I've also had this camera working successfully in a LabView vi but now, for some reason, I am getting an error message "Attribute out of range  (-1074360302)". 
    I've tried using different gain values (since MAX sometimes gives an attribute out of range error relating to gain) but am not having much success.
    Has anyone else experienced this problem and found a work around?
    Lightworker 

    Hi LightWorker,
    I've not seen this probelm specifically with Dalsa Spyder SG-11 cameras but there are several KnowLedge Base Articles on the error for various differnt models of camera. It may be that one of these fixes will apply to your camera as well.
    How Do I Resolve "Error: 0xBFF69012 Attribute value is out of range” When Connecting to a GigE Camer...
    Why do I get Error 0xBFF69012 "Attribute Value is Out of Range" with my Basler GigE Camera?
    Stingray Camera & NI LabView / Vision Builder Error -1074360302 "Attribute is out of range"
    Please let us know if any of these solve your issue.
    Kind regards,
    James W
    Controls Systems Engineer
    STFC

  • Receiving Error "A Number Is Out of Range" in Acrobat 8.1.2 and 7.0

    I create mapbooks for the county I work at using ESRI's ArcMap ArcEditor. Once the book is done I convert it to PDF so that officers, fire fighters, etc. can open it on their laptops. Recently I started receiving the error "A Number is Out of Range" when I finish combining the PDF files into a binder. The error persists anytime I change pages and I have to click OK several times before it goes away. This becomes a problem for emergency management when their trying to search a road, plus it is also very annoying. Does anyone know how to get around this? It didn't use to do this. I thought maybe it was the fonts I was using, so I changed most of them to Arial and Times New Roman, yet it still persists, but seems slightly better. I cannot find anything on Adobes website about A Number is Out of Range. Also, I am using Acrobat Professional 8.1.2 and have also tried Professional 7.0. I'm running Windows XP. I have also tried reverting back to old versions of ArcMap and also the mapbook software MapLogic, but nothing helps. Any help would greatly be appreciated.

    I'm getting this error also, and I don't think it's a font issue. Here's my situation.
    I created a 144-page manual in Adobe FrameMaker 8.0 using the same template and fonts that I have used in several other large manuals. I saved the manual as a PDF using Acrobat 3D 8.0, and is get the mind-numbingly vague error "A number is out of range." I didn't get this error in previous versions of this manual, nor do I get this error with the other manuals on which I am currently working. I had inserted some EPS technical drawings, so I opened all of them in Illustrator CS3 and Created Outlines for any text that appeared in the illustrations.
    After two days of replacing all of the fonts, optomizing PDFs, and distilling, distilling, and distilling again, I was not able to get rid of this message using Acrobat. I finally pulled out my MacBook Pro, opened the PDF manual using Preview, saved the PDF under a different name (no need to apply a Quartz filter), and (abracadabra!) the vague error message is gone!
    Fonts may be one cause of the annoyingly vague "A number is out of range" error, but they are not the only one. And with such informative error messages as that, I doubt I'll ever know what is really wrong with my PDF.
    Cheers!
    Michael Opsteegh

  • HT4972 I can't get my ipad to update. It keeps telling me there was an error and internet timed out.

    I can't get my ipad to update. It keeps telling me there was an error and internet timed out.

    Try disabling your firewall and your anti virus software until the update downloads and installs on the iPad.

  • Error in RunLogicAgainstSelection:Subscript out of range

    Dear experts,
    I'm writing a cross application *RUNALLOCATION from application InvCost.
    While validating the logic I ot this error saying
    "error in RunLogicAgainstSelection: Subscript out of range" and here's the code
    *RUNALLOCATION
    *FACTOR=1/TOTAL
    *APP               WHAT=FINANCE;          WHERE=INVCOST;          TOTAL=<<<
    *DIM TIME          WHAT=%TIME_SET%;     WHERE=<<<;          TOTAL=<<<
    *DIM DATASRC          WHAT=TEMP;          WHERE=INPUT;          TOTAL=INPUT
    *DIM LOB          WHAT=00000;          WHERE=;               TOTAL=
    *DIM COSTCENTER          WHAT=122;          WHERE=;               TOTAL=
    *DIM MACCT          WHAT=5601;          WHERE=;               TOTAL=
    *DIM FACTORY          WHAT=0000F;          WHERE=[L_f]="7";     TOTAL=EACH([L_f]="7")
    *DIM INTFAC          WHAT=;               WHERE=NONINTFAC;     TOTAL=EACH(BASE(ALLINTFAC))
    *DIM INVACCT          WHAT=;               WHERE=FUC_L;          TOTAL=FFACTOR
    *DIM PARNO          WHAT=;               WHERE=NONPARTNO;     TOTAL=EACH([INVTYPE]="L")
    *DIM SACCT          WHAT=00;          WHERE=;               TOTAL=
    *DIM CATEGORY          WHAT=ACTUAL;          WHERE=<<<;          TOTAL=<<<
    *DIM RPTCURRENCY     WHAT=LC;          WHERE=<<<;          TOTAL=<<<
    *ENDALLOCATION
    From WHAT there's only one value and devid by TOTAL then put into all base members of WHERE.
    Factory part is a little tricky cause I'm not sure if it'll give me only base members for the given condition.
    Any helpful comments are welcome. Thanks a million...
    ,Jim Hsu

    Hi Jim,
    I think you need to use the "USING" clause, as in this simple example. This is where you define the allocation driver.
    *RUN_ALLOCATION
    *FACTOR USING/TOTAL
    *DIM Product What=NoProduct; Where=[ProductLevel]="5"; USING=<<<; TOTAL=<<<
    *DIM Account What=MarketingExpense; Where=<<<; Using=Revenue; Total=<<<
    *ENDALLOCATION

  • FPM Error: An internal error occured: String index out of range -4

    Hi All,
    I have imported the SSA BP to my EP (7.0), however, when I tried to create a custom FPM view & FPM Application for my custom WD application....the system will just prompt the error message "An internal error occured: String index out of range -4".
    Can anyone advise what could be the problem? and how to resolve it?
    Thanks in advance!
    Best Regards,
    SY

    Hi,
    You are trying to call the index of the String whose length is 4., but in the code you may have called from 1 to 4.. which should be 0 to 3.
    If you can show the stack trace of the exception, we can pinpoint the code / line.
    Just check the WD code..!!
    Thanks,
    Raags

  • Image Manager : upload image - error message String index out of range

    Hello,
    i'm facing an issue with the upload functionality of 'Image Manager'.
    When i upload a file, systematicaly an error message pops up :
    "error message String index out of range : - XXX"
    Where XXX is a value as large as the size of the file.
    I have the feeling that the problem may come from the installation of VC.
    Did someone encountered this issue ?
    Thank you

    Hi,
    Plz check the below link
    https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes_boj/sdn_oss_boj_bip/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/scn_bosap/notes.do
    Govindu

  • MAX cannot find my camera attributes

    I'm still learning about machine vision to do a project that require image processing. I'm using LabVIEW 2010 and my camera is only my laptop webcam (MAX recognize it as: USB2.0 UVC VGA WebCam). I'm trying to do a feature like the one in the "Grab and Attributes Setup.vi" example, which is to control, for example, white balance. Running the example itself, I can change the white balance in LabVIEW (not in MAX). The problem is that in MAX, camera attributes shows exactly nothing, thus I cannot or dont understand how to access that attribut.
    So why is that the example in LabVIEW can adjust the white balance, while in MAX, no camera attributes at all is displayed?
    PS: My friend using different laptop but same brand, type, model, spec (identical hardware), same driver, his MAX can detect these attributes.

    the camera itself is onboard the laptop (not seperated webcam). I still haven't figure out why the attributes sometimes appear and sometimes is not. I've tried reinstalling my camera driver, IMAQ, and IMAQdx driver. I'll try using seperate webcam this weekend. Restarting my komp is also not the answer because it still appear and missing everytime. as for the reset, I cannot find it in tools menu. There's only "Reset NI-DAQmy Configuration".
    MAX version is 4.8.0f0
    NI-IMAQ 4.5
    NI-IMAQ I/O 2.4
    NI-IMAQdx 3.8
    LabVIEW 2010 SP1 (evaluation license)
    EDIT: I've attach my .vi files. When the attributes appear in MAX, this .vi is working fine and as I wanted, but when it is missing, the .vi returns error. The error message:
    Error -1074360305 occurred at Property Node (arg 2) in 3-8_Acquiring using Property Node.vi
    Possible reason(s):
    NI-IMAQdx: (Hex 0xBFF6900F) Attribute not supported by the camera.
    The read attributes such as BayerGainR is just for me testing, no particular use.
    Attachments:
    3-8_Acquiring using Property Node.vi ‏54 KB

  • Certificate not yet generated errors and wifi drop outs

    Hello all!  Recently I've been getting the following errors in console
    11/5/13 8:02:52.815 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.815 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.816 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.816 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.817 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.817 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.817 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.818 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.818 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.819 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.819 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.820 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.821 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.821 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.824 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.827 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.828 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.949 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:52.986 PM apsd[87]: Certificate not yet generated
    11/5/13 8:02:53.369 PM apsd[87]: Couldn't find cert in response dict
    11/5/13 8:02:53.370 PM apsd[87]: Failed to get client cert on attempt 1, will retry in 15 seconds
    The last line keeps repeting after it tries again attempt 101, will retry in 900 sec etc...
    Additionally I've noticed that periodically my wifi will drop out, and when I go to Airport Utility my Extreme is unavailable.  I don't know if this error and the two the wifi drop outs are linked or not.  At first I thought it was the new firmware for the basestation, but now I'm not so sure because last time I launched airport utility and the extreme was unavailable I saw the basestation come back on line.
    One final note.  I have a home server on a mac mini (ML Server essentially for ituens shared liberary).  All the macs access this server.
    Thanks in advance

    From the menu bar, select
               ▹ About This Mac
    Below the "OS X" legend in the window that opens, the OS version appears. Click the version line twice to display the serial number. If the number is missing or invalid according to this web form, take the machine to an Apple Store or other authorized service center to have the problem corrected.

  • MP Error: StringIndexOutOfBoundsException: String index out of range: -1

    Hi All,
    We are using PI 7.1 EHP1, Where in we would like to see the capabilty of User-Module for Conversion of IDoc Messages Between Flat and XML Formats. Gone thru the blog (/people/sap.user72/blog/2005/07/04/get-into-the-zone - Part 2) and maintained the necessary NWA configurations and maintained the necessary module parameters (SAPRelease, SourceJRA, TargetDestination) in Sender File Adapter.
    Now the file is not been picked by file adapter upon checking the Comm Channel Monitoring below error:
    MP: exception caught with cause java.lang.StringIndexOutOfBoundsException: String index out of range -1
    Any help would be highly appreciated.
    Thanks in advance

    Hi Ramani,
    I hope you must have found a solution on this, if not then kindly consider changing your source files, as this error corresponds to only one thing: i.e. DATA Issue. You need to correct the data which you providing to the module for conversion.
    I faced this problem and corrected it by just correcting my test file.
    Regards,
    Nipun Shedhani

  • FM8 -- Acrobat7 Error: A number is out of range

    When PDFing a FM8 doc, I got an Acrobat error message: "A number is out of range." Acrobat produced a PDF, but the first page was page Zero! and the Properties of the Acrobat doc were not accessible. Not good.
    Searched and searched for answers, but didn't come up with anything.
    The FM8 doc is very basic -- only three standard fonts, 10 pages long, nothing fancy. The only unusual thing (if you want to call it that) is that I imported the text (copied in) from a .txt file, which originated as a Word doc.
    So, I thought... hmmm... save first as a .MIF, then back to a .FM and see if that helps.
    It did.
    I don't know much about .MIF files. It must have cleaned up some garbage brought over from Word. You brainiacks who frequent this Forum probably understand completely how the .MIF works its magic.
    Anyway, if anyone else gets this error message, I thought I'd document my solution with the error message in the subject line.
    From Smokey Northern California,
    Karen

    The file is corrupt. Get a new undamaged copy.
    Mike

  • My 2011 mac mini screen is black and has an "out of range" message

    My 2011 mac mini is hooked up to a monitor and it has a black screen with an "out of range" message. I'm not sure how to fix it. everything is plugged in. please help!

    Reset the PRAM > Resetting your Mac's PRAM and NVRAM
    1. Shut down the computer.
    2. Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    3. Turn on the computer.
    4. Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    5. Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    6. Release the keys.

  • Error : CLI0111E Numeric value out of range

    Hello:
    While extracting data through generic datasources, extraction fails in the source system with the following error message.
    Database error text........: "CLI0111E Numeric value out of range.
    SQLSTATE=22003 row=1 col=12"
    Any idea what does this mean?
    Thanks

    Hello:
    While extracting data through generic datasources, extraction fails in the source system with the following error message.
    Database error text........: "CLI0111E Numeric value out of range.
    SQLSTATE=22003 row=1 col=12"
    Any idea what does this mean?
    Thanks

  • I have an alm Tiway host cmd error response 0002: address out of range

    Some of the i/o points do not display either as alias or as native memebers.

    Hello,
    Thank you for contacting National Instruments
    I�m not completely clear on your issue. Here are a few questions that should help me answer your questions better:
    1) What version of Lookout are you using?
    2) Are you using the Lookout Tiway object? If not, what Lookout object are you using?
    3) How are you receiving this error message? Is this being received from the Alarms Window?
    4) Has this communication with your Tiway ever worked? If so, what has changed since stopped working?
    5) Can you give me more information on the way you are connecting and communicating to the Tiway? Also, can you tell me what model of PLC you are using?
    6) What data members are not reading correctly from the Tiway object? Which data members, if any, are reading correctly?
    I have included a link to a Knowledgebase article which may help out in diagnosing the communications from the Tiway object:
    How Do I Create a Communication Diagnostic File for the Lookout Tiway Object?
    I hope this helps. Please let me know the answers to the above questions.
    Ken S.
    Applications Engineering
    National Instruments

  • FOR/NEXT loop produces Error in ProcessSQL: Subscript out of range

    Hi all,
    The 2nd FOR/NEXT loop in the following code produces Subscript ouf of Range error:
    *LOOKUP RATEAPP
    *DIM MODEL:RATEENTITYDIM= DRIVEDIM.DRIVER_ENTITY
    *DIM MODEL:RATEACCOUNTDIM= DRIVEDIM.DRIVER
    *DIM MODEL:INPUTCURRENCYDIM = "EUR"
    *ENDLOOKUP
    // Select lookup and normal members by group
    *SELECT(%DRIVERSA%, ID, DRIVEDIM, "[GROUP] = 'A' AND [DRIVER] <> ''")
    *SELECT(%MANUALSA%,ID,DRIVEDIM, "[GROUP] = 'A' AND [SOURCE] = 'MAN'")
    *XDIM_MEMBERSET DRIVEDIM= %MANUALSA%, "U_TEMP"
    *WHEN ACCOUNTDIM.ACCTYPE
    *IS *
         *REC(EXPRESSION=1, NOADD, DRIVEDIM="U_TEMP")
    *ENDWHEN
    *GO
    // this is ok
    *FOR %MANSET% = %MANUALSA%
         *WHEN DRIVEDIM
         *IS %MANSET%
         *WHEN %VALUE%
         *IS <> 0
                   *REC(FACTOR=GET(DRIVEDIM="AD.TEMP"),DRIVEDIM="AD.TEMP")
         *ENDWHEN
         *ENDWHEN
    *GO
    *NEXT
    *XDIM_MEMBERSET DRIVEDIM= %DRIVERSA%, "U_TEMP"
    // this is not OK
    *FOR %DRIVSET% = %DRIVERSA%
         *WHEN DRIVEDIM
         *IS %DRIVSET%
              *WHEN %VALUE%
              *IS <> 0
                   *REC(FACTOR= GET(DRIVEDIM="U_TEMP") * LOOKUP(MODEL),DRIVEDIM="U_TEMP") //  * LOOKUP(MODEL)
              *ENDWHEN
         *ENDWHEN
    *GO
    *NEXT
    If I remove the FOR/NEXT loop, this runs fine. The error occurs everywhere - in logic debugger, in DB, in ExecuteBaseLogic if included in Default logic. The REC statement inside the loop can be anything, even as simple REC(FACTOR=1,DRIVEDIM="U_TEMP"), so the problem is in the loop, not anything else. It validates nicely and the compiled logic looks just as expected.
    This error could occur sometimes if the membersets are too large. However, in this example, the number of members is rather limited. In the debugger is is possible to limit the data region to single specific intersection and the DRIVEDIM membersets combined is exacly 15.
    Could it be possible that the error is caused by member ID-s like AD.1.AVGWAGEGROWTH (length=18)? Is there anything else that can cause  trouble?
    Any ideas appreciated.
    Thanks
    Madis
    Edited by: Madis Udam on Mar 24, 2011 11:06 AM

    I don't think you should have"." dot's in you ID's.
    think about it, in your code you have ACCOUNTDIM.ACCTYPE, which represents the account type of the dimension.
    If you have an id "AD.1.AVGWAGEGROWTH"; wouldn't it think that you are trying the get a value of some member?
    That's just a guess, we established that we wouldn't use any special characters on our id's
    It's working so far
    Try changing the line
    *IS %DRIVSET%
    to
    *IS "%DRIVSET%"
    Edited by: Leandro Cardoso Feliciano on Mar 28, 2011 10:45 PM

Maybe you are looking for

  • Sync problems with Vista, Desk Top Vers 6.2 and Tungson C

    My wife recently bought a new cell phone with Palm Centro that loaded vers 6.2. My palm TC running OS 4.5 will not sync. If I try overighting either way I get duplicates in Address catagories but my datebook, Docs to go, address, memo, ToDo, and expe

  • Issue with adobe acrobat 7.1.0 standard on windows 7 professional 64-bit

    hi, i have been using my aa 7.1.0 standard with windows xp professional sp2 32-bit for over a couple of years with great ease. recently, i upgraded to windows 7 professional 64-bit. when i reinstalled aa 7.1.0 standard on that, i hit a wall. i get th

  • Editing  a Web site SWF file

    Funky, allow me to try again. right words are difficult for me come by but I try. I have a Web site that uses a 260K Swf file for presentation. My original designer is no longer available. I am trying to make changes to update some of the info on the

  • Is there a way to restore a macbook air to factory settings?

    hi, i recently bought my friends macbook air. he made me a new account on the laptop and deleted his account. this is fine but i'm finding family photos and address book contacts and the computer's name is his name. i was wondering if there was a way

  • Error while activating Stored Procedure

    Hi All, I am tried to create the Stored procedure but when I am trying to activate same then Procedure is not getting activated. Please help. Regards, Neha Singla