No address available for SVC connection!

I am trying to create a SSLVPN connection using Cisco Anyconnect Client after entering username and password, I am getting following error message in attached screenshot. I already created a ip local pool vpnpool 192.168.60.10-192.168.60.15 mask 255.255.255.0 and associated with correct tunnel-group sslgroup. Everytime i attempt to connect i get error message no address available for SVC Connection.
Any help or suggestions related to this issue will be helpful.
Thanks,
Ali

Hi MKD,
I only have one telnet session open and ASDM session to this ASA on top of that I am using CiscoAnyConnect to intiate SSL Connection. I also try to close ASDM session and reattempted again but getting same error message.
Do you have any other suggestions?
Forgot to mention I don't have a RDP session opened.
Thanks,
Ali

Similar Messages

AnyConnect: No Address Available for SVC Connection on Cisco ASA 5505

Get Error
The secure gateway has rejected the connection attempt. A new connection attempt to the same or another secure gateway is needed, which requires re-authentication. The follow message was received from the secure gateway: No address available for SVC connection.
ip local pool VPN 192.168.250.50-192.168.250.60 mask 255.255.255.0
tunnel-group SSL type remote-access
tunnel-group SSL general-attributes
address-pool VPN
tunnel-group Any-Connect type remote-access
tunnel-group Any-Connect general-attributes
address-pool VPN
I have a VPN pool
I can make a clientless SSL connection

Hi,
Maybe you are not falling into that tunnel-group SSL? By default, you will fall into the DefaultWebvpnGroup unless you choose the TG via a dropdown or directly access the group via a groupurl.
Example: When no 'tunnel-group-list' or 'group-url' is configured:
Accessing https:// will take you to DefaultWebvpnGroup.
When 'tunnel-group-list enable' is configured under webvpn, you will get a dropdown of tunnel-groups to choose from [provided you have an alias defined for the group]
When group-url is configured for a particular TG, say https:///test , on accessing that URL, you are taken to that group directly.
So basically, you would need to check which group you are hitting. Running 'debug webvpn 255' should also show you this.
Thanks
Rahul

Programs that require a network connection won't work because there is no virtual IP address available for this session.

Programs that require a network connection won't work because there is no virtual IP address available for this session. Per application IP virtualization is enabled.
There are in fact available IP address's within the dhcp scope. Before I dig to deep into root cause.. Could the problem be RDS CAL licensing running out, or isn't that not a symptom of my error message?

Hi,
Thank you for posting in Windows Server Forum.
As per my research, there is no any issue related to RDS CAL licensing. Prior to the issue which you are facing, there are some basic setting which need to configure.
Application Compatibility – Turn on Remote Desktop IP virtualization
Some applications require a unique IP address, which is by default logically not the case if the application is running on RD Session Host. To solve this issue, Remote Desktop IP Virtualization is introduced. With this setting you enable the IP virtualization
feature. When enabling this setting you need to specify if the virtual IP is provided per session or per program. When using per program you need to define the executable to which an IP address should be configured. Desktop IP virtualization also needs the
configuration of the next setting.
Application Compatibility – Select the network adapter to be used for Remote Desktop IP Virtualization
When you need to use Remote Desktop IP virtualization configuring this setting is mandatory. You need to specify the IP address of the Network Interface Card which should be used for this feature. Besides the IP address you need also to specify the network
mask using the slash notation, for example 192.168.77.201/24.
Application Compatibility – Do not use Remote Desktop Session Host server IP address when virtual IP address is not available
More information:
Microsoft RDS Policies explained (Part 2)
http://www.virtualizationadmin.com/articles-tutorials/vdi-articles/microsoft-hyper-v/microsoft-rds-policies-explained-part2.html
Configuring Remote Desktop IP Virtualization II
http://blogs.msdn.com/b/rds/archive/2009/07/15/configuring-remote-desktop-ip-virtualization-ii.aspx
Hope it helps!
Thanks.
Dharmesh Solanki

HT201320 I want to have all the facilities of my Ipad obtained for my e mail address, available for another e mail address belonging to my wife. Anyone know how I set this up please?

I want to have all the facilities of my Ipad obtained for my e mail address, available for another e mail address belonging to my wife. Anyone know how I set this up please? I am a new user and long in the tooth so any help would be much appreciated.

What do you mean by "facilities of my Ipad obtained for my e mail address"?
Do you mean you want to setup your wife's email account on your iPad? Or something else?

Tracing TCP Source/Destination Addresses/Ports for ongoing connections

On Solaris 10 U4 through U7, I'm trying the following just to perform basic tracking of TCP source/destination addresses and ports, using code similar to what is available in tcpsnoop_snv and tcptop_snv.
The odd thing is that the addresses/ports appear to be zeroed out - are they being cached outside of the conn_t data structure?
#!/usr/sbin/dtrace -Cs
#pragma D option switchrate=10hz
#pragma D option bufsize=512k
#pragma D option aggsize=512k
#include <sys/file.h>
#include <inet/common.h>
#include <sys/byteorder.h>
#include <sys/socket.h>
#include <sys/socketvar.h>
/* First pass, for all TCP Read/Write actions, collect source/destination
   IP + Port - after a few secs, print them all out */
fbt:ip:tcp_send_data:entry
/* Outgoing TCP */
self->connp = (conn_t *)args[0]->tcp_connp;
fbt:ip:tcp_rput_data:entry
/* Incoming TCP */
self->connp = (conn_t *)arg0;
fbt:ip:tcp_send_data:entry,
fbt:ip:tcp_rput_data:entry
/self->connp/
/* fetch ports */
#if defined(_BIG_ENDIAN)
self->lport = self->connp->u_port.tcpu_ports.tcpu_lport;
self->fport = self->connp->u_port.tcpu_ports.tcpu_fport;
#else
self->lport = BSWAP_16(self->connp->u_port.tcpu_ports.tcpu_lport);
self->fport = BSWAP_16(self->connp->u_port.tcpu_ports.tcpu_fport);
#endif
/* fetch IPv4 addresses */
this->fad12 =
    (int)self->connp->connua_v6addr.connua_faddr._S6_un._S6_u8[12];
this->fad13 =
    (int)self->connp->connua_v6addr.connua_faddr._S6_un._S6_u8[13];
this->fad14 =
    (int)self->connp->connua_v6addr.connua_faddr._S6_un._S6_u8[14];
this->fad15 =
    (int)self->connp->connua_v6addr.connua_faddr._S6_un._S6_u8[15];
this->lad12 =
    (int)self->connp->connua_v6addr.connua_laddr._S6_un._S6_u8[12];
this->lad13 =
    (int)self->connp->connua_v6addr.connua_laddr._S6_un._S6_u8[13];
this->lad14 =
    (int)self->connp->connua_v6addr.connua_laddr._S6_un._S6_u8[14];
this->lad15 =
    (int)self->connp->connua_v6addr.connua_laddr._S6_un._S6_u8[15];
/* At this point, this->{f|l}ad1{2345}->connua_v6addr.connua_{f|l}addr._S6_un.S6_u8
    are empty - where is this data? */
}

http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/css11500series/v7.50/command/reference/CmdGrpC.html#wp1139667
portmap [base-port base_number|disable|enable|number-of-ports number|vip-address-range number]
disable
Instructs the CSS to perform Network Address Translation (NAT) only on the source IP addresses and not on the source ports of UDP traffic hitting a particular source group. This option does not affect TCP flows.
For applications with high-numbered assigned ports (for example, SIP and WAP), we recommend that you preserve those port numbers by configuring destination services in source groups. Destination services cause the CSS to NAT the client source ports, but not the destination ports.
Note If you disable flows for a UDP port using the flow-state table and configure the portmap disable command in a source group, traffic for that port that matches on the source group does not successfully traverse the CSS.
The CSS maintains but ignores any base-port or number-of ports (see the options above) values configured in the source group. If you later reenable port mapping for that source group, any configured base-port or number-of ports values will take effect. The default behavior for a configured source group is to NAT both the source IP address and the source port for port numbers greater than 1023.
There is no possibility to disable it for TCP.
We need to source nat the port to guarantee that the server response comes back on the same module/CPU and the internal packet allocation algorithm is based on src and dst ports.µ
Gilles:

Possible to use Azure SQL as database for RD Connection broker high availability?

I am looking in to setting up a highly available Remote Desktop services service on Azure and note that the high availability for the Connection Broker service needs a full SQL database (rather than the LocalDB used for one instance). Is it possible
to use an Azure SQL database for these purposes (i.e. opposed to VMs running SQL Server)?
Has anyone had any experience with this? This would be nice as I am not looking at thousands of users and the Azure SQL would provide the high availability for the database without creating multiple (expensive) VMs running SQL server.

So far there's no such a feature in azure sql, you can vote for it
http://feedback.azure.com/forums/217321-sql-database/suggestions/423275-enable-sql-service-broker-in-sql-azure

Disable Forced Smart View Upgrade for HFM Connections

Our users are trying to validate data in a new development application and, when connecting to that application, are getting a message from Smart View that a new version is available. Is there a way to disable this message? Our development and production environments are both on the same version of HFM.
I did see some options related to provider services in the help documentation, but when I follow the steps listed in the documentation, the option to access provider services is not available for HFM connections.
I look forward to your responses!
S

I'm not sure what version of Smartview you are using, so your mileage may vary.
Client Side:
With 11.1.2.1+ - Near the bottom right of the Smarview window is an icon for 'Provider Services' which takes you to a screen with a checkbox to enable / disable telling the end user when a new version is available and allowing them to upgrade it.
Server Side:
I'm not sure what version it started with, but the version.XML file that exists with the smartview.exe for download w/ Workspace allows you to configure some of the parts for autodownloading the file.
Additionally when you configure the HFM website using the HFM config tool, there is a checkbox (at least in System 9 versions) that would enable you to force end users to upgrade to the newest version. I don't believe it auto upgrades them; however, it prevents them from using Smartview which would ultimately get them to upgrade. :)
If you need more specifics let me know, this is just off the top of my head.

Failure of server APACHE bridge::No backend server available for connection

All,
I have an env: Browser -> OHS -> WLS(Apex Listener) -> Oracle DB.
If any SQL run for more than 5 mins, i get the below error.
Failure of server APACHE bridge:
No backend server available for connection: timed out after 10 seconds or idempotent set to OFF or method not idempotent.The only error i get is from the OHS's log
[2013-04-03T06:45:57.2946-05:00] [OHS] [ERROR:32] [] [core.c] [host_id: aa050] [host_addr: 121.146.60.102] [tid: 1260554560] [user: oracle] [ecid: 004qNDJn1du7m3KaETn3ES0004Ll00001T] [rid: 0] [VirtualHost: my.team.com:443] ap_proxy: trying POST /pls/apex/wwv_flow.show at backend host 127.0.0.1/7003; got exception 'Backend Server not responding'; state: reading status line or response headers from WLS (wrote? Y read? N); not failing over because method not idempotent, referer: https://my.team.com/pls/apex/f?p=4500:1003:16571271664493::NO:::Is there a timeout variable other than the below in WLS?
Session Timeout (in seconds): 3600 .
TIA,
JJ

Regardless of the version, this is not exactly a "Forms" failure. This is an issue between OHS and WLS. Basically it means that OHS (via mod_wl_ohs) was unable to communicate with WLS_FORMS (or whichever managed server you are trying to access). Most often this means the managed server is not running or not responding. If you believe it is running and is responsive (test by hitting it directly) then the problem is probably related to your installation. Generally, if you have not properly configured your networking before you installed WLS and FMw, then this can occur. For example, on Windows machine which do not have static IP addresses, the Installation Guide instructs you to install the Windows loopback adapter and configure it. If you did not do this, OHS likely will not be able to contact WLS_FORMS.
You can test what I have described above by attempting to access WLS_FORMS directly. For example:
http://yourHost:9001/forms/frmservlet
If that works, the issue is probably related to a net config issue.
If you have access to MyOracle Support, refer to these notes:
<blockquote><li>Failure Of Server APACHE Bridge After Running Report From Forms 11gR2 on Windows 64-bit platform (Doc ID 1457845.1)
<li>Oracle Fusion Middleware 11g - Troubleshooting the Error "Failure of server APACHE bridge" (Doc ID 1304095.1)</blockquote>
The product Documentation Library can be found here:
http://docs.oracle.com/cd/E24269_01/index.htm

This email address is not available for use as an Apple ID

hi
i had two apple accounts
and just wanted to change the primary email address for the both with each other
when i changed the first one my old email cant be used with other account then i tried replacing my old email it doesnt replace it says
This email address is not available for use as an Apple ID. You may already have an Apple ID associated with this address. Please try again or sign in using your existing Apple ID.
please help me

Yes, I am having the same problem. When I called apple they said that things were "tied up somehow" with another account that has a do different birthday than me. Uuuuuhh? So that means someone else can log in?... I have a feeling there is a big vulnerability with the three login options, just like with the current and past password retrieval. Apple had only suggested that I delete my current set up on my serviced and make a new ID and email.
I Just got a new email and made a new Apple ID account For now. I was hoping the email would work itself out. I assumed If I could make sure everything was verified, not associated with another account, and try to get rid of the alternate id and second email option also used to sign in (seen in Apple ID management) that could possibly be construed or mixed up with something else that it would eventually free up and become "available" again. Unfortunately im still waiting In hopes in just needs to recognize the email isn't associated with anything.
I have had a few major concerns with apple products lately especially with security. My iPhone 4s was hacked too. Some ******* was listening/recording and when I hooked to Internet he sent out the recorded portion that was available. Talk about ****** up.

How to delete old account, I can't log in due to - This email address is not available for use as an Apple ID. You may already have an Apple ID associated with this address. Please try again or sign in using your existing Apple ID.

How to delete old account, I can't log in due to error - This email address is not available for use as an Apple ID. You may already have an Apple ID associated with this address. Please try again or sign in using your existing Apple ID.

All good, I loved with AppStore and now everything seems to be back to normal.

This email address is not available for use as an Apple ID. You may already have an Apple ID associated with this address. Please try again or sign in using your existing Apple ID.

I want to change my apple id but get the message "This email address is not available for use as an Apple ID. You may already have an Apple ID associated with this address. Please try again or sign in using your existing Apple ID.". I try to log a call with apple support and I get a message like "cannot schedule a call". That leaves me out of options. Any ideas?

Hi billfromwandering,
I'm sorry to hear you are having these issues changing your Apple ID. It is correct that if an email address has been used previously for an Apple ID, it can not be used for a different Apple ID, as noted in this article:
In most cases, your Apple ID is also the primary email address of your Apple ID account. You can change your Apple ID to any other email address you control, as long as it's not already in use as an Apple ID. If your email address ends with @icloud.com, @me.com, or @mac.com, it's already an Apple ID.
Change your Apple ID - Apple Support
If you are certain that the email in question has never been used for an Apple ID and you are having issues contacting Apple Support regarding this issue, you may want to make sure you are going through the Apple ID support channel on the following page:
Apple ID - Contact - Apple Support
Regards,
- Brenden

In Address Book, why does Apple let you create custom fields in the Template cards but not have them available for importing?

I open Address Book, go into Preferences, select Template and under the Names field (friend, assistant, father, etc) I add a custom field called "Principal".
I also add two more custom fields in the Email area.
Quit Address Book then relaunch. Add a new contact and the new custom fields, Principal, etc. are there. All good so far.
I have a Now Contact file with about 200 contacts in it. I export all fields as a Text file, Tab delimited. No problems there. With Address Book launched, select Import, pick the text file, leave Text Encoding on Automatic and click Open.
The window that shows the fields for Address Book and fields for the text file side by side opens. This is where you match up the correct fields for importing. If I go to one of the fields from the text file that I created a custom field for, click under the Address Book heading on the Do not import, scroll thru the Apple choices of fields, none of the custom fields show up. Only the original Apple ones are there. Why does Apple let you create them in the Template area but not have them available for importing? Does anyone have suggestions on getting around this?

While most likely not of interest to you, Spotlight can also tell you where the files it finds are located
Hover the mouse pointer over the name, and press Command-Option and the path to the file will be displayed.
As for opening a terminal session in the directory where a file is located, there is Applescripts that do just that as well as specific features in Lion/Mountain Lion terminal:
<http://stackoverflow.com/questions/420456/open-terminal-here-in-mac-os-finder>
<http://hints.macworld.com/article.php?story=20110729034827358>
<http://www.macworld.com/article/1047793/folderinterm.html>
<http://www.macworld.com/article/1161876/open_finder_folder_in_terminal.html>
<http://www.macobserver.com/tmo/article/os_x_lion_open_a_folders_location_in_term inal>

Why am I getting this error message when trying email a PDF?Server Connection Error. Please verify that port 143 is available for connection on your machine or contact your administrator.

My Inspector for my house sent me his report via PDF that I had to access from an online link. I downloaded it but cannot forward it in an email to my insurance company who is requiring a copy. I get this error report every time:
Server Connection Error. Please verify that port 143 is available for connection on your machine or contact your administrator.
I have no idea what this means. Can someone help? I really don't want to have to print and scan this beast but I've been messing with this for 2 days now and am out of ideas.
Thanks!

I'm having the same issue. Did you resolve it?

HT1766 My IPAD software update is avail for the iOS 7.0.3 I keep trying to install it. I have my IPAD hooked up to my MAC and the Wi FI, I have internet open It keeps telling me now connected to internet. What am I doing wrong.

My IPAD software update is avail for the iOS 7.0.3 I keep trying to install it. I have my IPAD hooked up to my MAC and the Wi FI, I have internet open It keeps telling me not connected to internet. What am I doing wrong.

You can try resetting your iPad by simultaneously pressing and holding the Home and Sleep/Wake buttons until you see the Apple Logo. This can take up to 15 seconds so be patient and don't release the buttons until the logo appears.
Try again to see if the problem persists.

HT204380 I am new to Facetime. I want to be able to talk to my iMac from my Macbook. When I try to connect via email I get a message that says the person being called "is not available for Face Time".

I am new to Facetime. I want to be able to talk to my iMac from my Macbook. When I try to connect via email I get a message that says the person being called "is not available for Face Time".

Hi PhiDor,
Thanks for visiting Apple Support Communities.
See this article for some information that can help:
FaceTime for Mac: Troubleshooting FaceTime
http://support.apple.com/kb/ts4185
Regards,
Jeremy

No address available for SVC connection!

Similar Messages

Maybe you are looking for