Not recognizable (array ?) function

Hello,
Guys, I've encountered an array function, which I could not find anywhere in Labview. (The example, containing this function was in a book). 
It's icon resembles somehow the "Interleave 1D Arrays" function under "Array" functions.
All I have is its icon's picture, and the context being used, that I've attached to this massage.
Could anybody tell me what this function does, or where I can find it in the functions palette ?
Attachments:
array_func.JPG ‏11 KB

That is a build array node resized to accept three 1d arrays of booleans where all inputs are set to concantenate array. The result is a 1d array of booleans.
Ben
Message Edited by Ben on 10-01-2005 04:48 PM
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Similar Messages

  • IMac will not recognize scan function of all in one printer

    My 24" iMac will print on the HP Photosmart 3210xi All in One, but will not scan.
    Twice, (to ensure I didn't miss anything) I have run the manual un-install procedures prescribed from HP, and installed the appropriate driver for Mac with no success.
    When I try to scan, the scanner wants to begin, but the computer displays the message, "Sorry, scanner could not be initialized. (Scanner not found.)" We have the correct driver (Not the Print only option).
    This printer still works "full-up" on the clunker PC, so it's not a hardware issue with the printer.
    Any others with similar all-in-one issues? Solutions?

    I had the same problem with my HP Photosmart 2610xi All In One Printer. I went to the HP website and downloaded the full feature software/drivers and now it works great. Below is the software that you should download for your printer...hope it works for you!
    HP Photosmart Full Feature Software/Drivers - Mac OS X v10.3 and v10.4 (Universal)
    08-2007 9.5 170.57M

  • Raid Admin 1.5 - Recognize Array button not active

    Hi all,
    just updated to RaidAdmin 1.5, updated firmware on both controllers to 1.5 version.
    I have 6 disks on which should be my lost array. Suddenly 'Recognize Array' button in utilities is not active.
    Any idea?
    Leos.

    ok. The whole story:
    Few month ago, I had RAID 3 schema on 6 disks. I did firmware update on my XRaid. This update WAS SUCCESSFUL. After XRaid restart, I lost my array. I didn't have backup. After unsuccessful local Apple support, I tried 3rd party companies to reascue my data. Noone helped me. I managed help from Apple in US, I sent my disks to them (quite expencive, I am from Czech Republic.). They recovered raid set on my disks to RAID 3 schema on 5 disks only - don't understand this. So I called them back a and I sent disks again, with detailed desription how it must be. Thay sayed OK and sent me back 6 disks, with no raid set schema - 6 unassigned to any array. And as a bonus, one of them was failed. So, now I have 6 disks, Apple claims, that raid schema is on disks (but i cannot see it on my raid - I realy tried everything - swapping possitions, controllers, cables .....). So when Raid Admin 1.5 brings this new function - recognize array, I started thinkink, that I have one more chance to recover my data back. But situation is as I described in first topic....

  • Windows says "device is not functioning" and "Windows does not recognize"

    I lost my USB dock connector cable for my ipod. I just went out today and bought a brand new "Cygnett GrooveLink Strech Retractable USB Cable for iPod". I was pumped when I came home to finally be able to add music to my ipod again, but alas when I plug the iPod in, Windows pops up saying that the device is not functional and that Windows does not recognize it. I tried everything from rebooting the iPod to re-downloading iTunes and iPod updater. After searching this site for the past few hours, I figured I'd try and possibly find some real answers here. Please Help!!

    Hey everyone,
    I had the same problems all of you are having. I
    just got a 5th generation video ipod. For a few
    days, my computer a) wouldn't recognize it; b) froze
    up when I connected it; c) mistook it for a mass
    storage device ("drive E"). I bought a USB 2.0
    notebook card which didn't work either and actually
    seemed to make the problem worse because when I
    connected the iPod to it my computer froze up.
    I was very confused because my new iPod worked on my
    brother's computer--which is much older than mine but
    still recognized the iPod and connected to it.
    Then I noticed that my brother's computer is running
    an older version of the ipod software. I used his
    disk to install "Ipod Updater 2005-06-26" rather than
    the new version of the software on the Apple Web
    site. Then I plugged my iPod into a USB 1.1 port.
    To my surprise, my computer finally recognized the
    iPod and is now loading music onto it. I cannot
    believe this worked. I wonder if the latest version
    of the software is faulty in some way.
    Try it! I hope it will work for you too. You will
    need an older version of the iPod updater software,
    so borrow it from a friend with an older ipod.
    I am having this problem also...It will work fine on the 1.1 but when i plug it into the 2.0 it has trouble recognizing it...

  • Outlook Drag 'n Drop functionality does not recognize BP Code

    Hi,
    I am using Outlook Drag 'n Drop functionality (with cockpit) in order to synchronize incoming e-mails. However, it does not recognize the BP and it lets the field blank. I have set the e-mail into the corresponding field on Business Partner as well as Contact Person. Isn't this the unique key for choosing automatically the BP?
    Thanks
    Gerasimos

    Hi,
    I am using this in 8.8 PL16 & sometimes it recognises & sometimes not. I hadn't given much thought to when it works or not, but wll start checking

  • Layout - not recognize the element when i call the function write_form

    Hi experts,
    I got a layout(se71) that not recognize the element that i add in the MAIN window when i call the layout from a program.
    what could it be?
    i add the element in se71.
    any help will be appreciated.
    Michal.

    Hi!
    the write form that u are calling should be as below....
    CALL FUNCTION 'WRITE_FORM'
       EXPORTING
          element                  = 'ELEMENT'
          window                   = 'MAIN'
        EXCEPTIONS
          element                  = 1
          function                 = 2
          type                     = 3
          unopened                 = 4
          unstarted                = 5
          window                   = 6
          bad_pageformat_for_print = 7
         spool_error              = 8
          codepage                 = 9
          OTHERS                   = 10.
      IF sy-subrc <> 0.
        MESSAGE 'MAIN window not called properly'(006) TYPE 'E'.
      ENDIF.                               " IF SY-SUBRC NE 0
    in the layout see if the code there with data element is proper as...
    /E  ELEMENT
       &var&
    Also this write_form FUNCTION MODULE should be called  b/w OPEN_FORM and CLOSE_FORM Function Modules.
    Regards

  • How can I perform the LINEST function using the new version of Numbers? The old method of using "command enter" to complete the array function does not work. Please help ASAP!!!

    LINEST function using Numbers for Mac

    Thank you for your help. This page is somewhat helpful, but I still don't quite understand.  I am using the Numbers program, and my assignment calls for me to use the LINEST function to return a set of 10 values. 
    When I googled how to do this, a lot of pages mentioned hitting "command+enter" to complete the array function, but they were using an older version of Numbers and it doesn't do anything when I try it in the new version.  I tried using "Index" with LINEST, and i've managed to get about 5 values out of it.

  • Is there any way to create a circular buffer using the INSERT ARRAY function?

    I saw the example using the REPLACE ARRAY function, but it uses too much CPU power on my laptop. I'm using it for a very sensitive application and saw that the INSERT ARRAY function used much less CPU power.
    I am also not wiring the index on the INSERT ARRAY function so that whatever is read from the buffer is added to the array.
    However, since it is not indexed, I don't know how to set the "write" index back to 0 when it reaches a certain sized array (ie 1000 elements). I was looking for an array property node, but couldn't figure out if one exists for the "current write index".
    Can anyone help?
    Thanks

    I will try to answer this question to my best understanding. I apologize if I interpreted the question wrong.
    You are using the "Insert Array" vi without wiring the index. By doing that, new elements will be added (appended) to the array.
    If you just want to know the current index to stop your acquisition when the array reach certain amount of elements, then you can use the "Array Size" vi to keep track of the size of the growing array. Remember that Array Size = last index + 1 because the index start at zero.
    A second option is that you may want to start over the array when it hits the maximum number of elements that you will allow. If that's the case, then you may want to re-initialize the array to a NULL state by stablishing a condition (for example, when the
    size of the array is 1000, re-initialize). I provided an example attached to this message showing how this can be accomplished. In the example, an 1D array grows in size using the "Insert Array" vi and inserting a random number. When the array reach 4 elements, it is re-initialized. You can expand this example by saving the array first to a file or some other holder before re-initializing the array. The example is in LabVIEW 6.
    Finally, if you want to replace the current values with new values, I think you do not have other choice but to use the "Replace Array" vi.
    Hope this can be of help.
    Regards;
    Enrique Vargas
    www.vartortech.com
    Attachments:
    array_example.vi ‏20 KB

  • TS1410 My iTunes will not recognize my iPod Nano 6th gen.   It has worked in the past and it works with my iPod 4th gen.  I've gone through the troubleshooting steps as suggested, but still -- nothing.  Now, what??

    iTunes will not recognize my Nano 6th gen. as a device.  It has been recognized  in the past and iTunes does recognize my Nano 4th gen.  The device connects to the Mac and charges allright.  All of the functions on the Nano work but want to modify my music, I'm tired of the same songs etc. 

    Universal Serial Bus controllers
         Intel(R) ICH9 Family USB Universal Host Controller - 2934
         Intel(R) ICH9 Family USB Universal Host Controller - 2935
         Intel(R) ICH9 Family USB Universal Host Controller - 2936
         Intel(R) ICH9 Family USB Universal Host Controller - 2937
         Intel(R) ICH9 Family USB Universal Host Controller - 2938
         Intel(R) ICH9 Family USB Universal Host Controller - 2939
         Intel(R) ICH9 Family USB Universal Host Controller - 293A
         Intel(R) ICH9 Family USB Universal Host Controller - 293C
         USB Composite Device
         USB Root Hub
         USB Root Hub
         USB Root Hub
         USB Root Hub
         USB Root Hub
         USB Root Hub
         USB Root Hub
         USB Root Hub
    I'm not sure if it charged when I hooked it up to my roommate's computer, but it definately didn't register either. If I put it on the dock it plays so the port is fine, but that still doesn't help me sync it to my computer.

  • Windows 7 pc does not recognize/find my iphone 5

    I went to upgrade my iphone 5 to the new ios 7.  I am not a regular "syncer"-that is it had probably been a few months.  Went into itunes and was prompted to upgrade pc to 11.1.  Error was I had my phone pluggged in while upgrading itunes to 11.1.  Came back about 30 minutes later and the itunes logo was hardset into my phone-rendering it useless.   Went Apple Store #1 and got it unlocked and discovered phone contents were all gone accept for Contacts.  Came back home and phone was still not recognized.  Went to Apple Store #2 and was told how to uninstall the Apple apps in the proper order and restart pc.  Performed this function and PC still does not recognize the iphone 5.  Double checked to make sure all Apple apps were installed.  At my wits end....

    You have done everything verbatim included with this link?
    http://support.apple.com/kb/ts1538

  • My ipod 1st gen battery went totally dead because the usb cable was defective. I've changed the cable.  now when i connect my ipod to the netbook, itune is not launching automatically and windows does not recognize it......how can these issues be resolved

    My ipod 32gb 1st generation battery went totally dead because the usb cable was defective.  I have since replaced the cable but now itune will not launch automatically as it did before and windows xp does not recognize it.  Nonetheless it is charging.  However can i resolve these issues bearing in mind that i am not tech savvy?

    have since replaced the cable but now itune will not launch automatically as it did before and windows xp does not recognize it. 
    Try disabling a/v software and turn off the Firewall on your PC.
    Disable antivirus software
    Turn-Windows-Firewall-on-or-off
    Then connect the iPod to your computer. Launch iTunes. If your computer still won't recognize the iPod check out this article.
    http://support.apple.com/kb/TS1538
    Once your iPod is functioning again, with it connected to your computer, launch iTunes. Select the iPod under Devices in the source list on the left.
    Select the box next to:   Open iTunes when this iPhone is connected
    That way iTunes should open automatically when you connect your iPod to your computer.
    And iTunes / Preferences - Devices. You can have your iPod sync automatically whenever it's connected from the Devices pane.

  • Itunes does not recognize my iphone 4 device

    I bought a new computer, tried to install itunes, after three different people tried to help me, i finally got itunes to install, but when I plug my iphone into my computer, itunes does not recognize the device.  I am trying to 1. upgrade my iphone soft ware to 10.5.3, utilize icloud, and perform basic functions of syncing my phone with my computer. Any help, anyone could provide would be appreciated.
    Tank you,
    Rose

    If your iTunes is the latest version, restart your computer and reboot your iPhone. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider until the Apple logo appears. Let go of the buttons and let the iPhone restart. See if that fixes your problem.

  • Regarding custom print program does not recognize elements in new windows..

    Hello Experts,
    I copied the standard print program RFFOUS_C since I need to add new windows and routines. But when I
    inserted my 'WRITE_FORM' to call the element in the new window it has an exception of '1' which I think it does not
    recognize the custom elements in the new windows. Below is my code:
    CALL FUNCTION 'WRITE_FORM'
                   EXPORTING
                     element                        = 'CHECK'
                     function                       = 'APPEND'
                    TYPE                           = 'BODY'
                     window                         = 'PAYEE'
                  IMPORTING
                    PENDING_LINES                  =
                   EXCEPTIONS
                     element                        = 1
                     function                       = 2
                     type                           = 3
                     unopened                       = 4
                     unstarted                      = 5
                     window                         = 6
                     bad_pageformat_for_print       = 7
                     spool_error                    = 8
                     codepage                       = 9
                     OTHERS                         = 10.
                  IF sy-subrc <> 0.
                   MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
                           WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
                  ENDIF.
    So I added the window 'PAYEE' and the code above was inserted in the routine 'SCHECK'. Hope you can help
    me guys. Thank you and take care!

    r u using the ' check' text element in your script window?, if u don't delcare in the script  window than only this kind of error will come.
    Thanks,
    Tirumal.

  • For one Urgent Change during performing the Approval(chnging the status to 'To be Tested') system does not recognize any changes using the CTS WBS BOM in the development system. The transaction is therefore incorrect or the status was reset by the system.

    For one Urgent Change while performing the one of the Approval before changing the status to 'To Be Tested'
    We are getting below error.
    The system does not recognize any changes using the CTS WBS BOM in the development system. The transaction is therefore incorrect or the status was reset by the system.
    COuld anyone please help us to know, How it can be resolved?
    We also have this below error.
    System Response
    If the PPF action is a condition check, the condition is initially considered as not met, and leads to another warning, an error message, or status reset, depending on the configuration.
    If the PPF action is the execution of a task in the task list, and the exception is critical, there is another error message in the document.
    Procedure
    The condition cannot be met until the cause is removed. Analyze all messages in the transaction application log.
    Procedure for System Administration
    Analyze any other messages in the task list application log, and the entries for the object /TMWFLOW/CMSCV
    Additional Information:
    System cancel RFC destination SM_UK4CLNT005_TRUSTED, Call TR_READ_COMM:
    No authorization to log on as a trusted system (Tr usted RC=0).
    /TMWFLOW/TU_GET_REQUEST_REMOTE:E:/TMWFLOW/TRACK_N:107
    For above error Table /TMWFLOW/REP_DATA_FLOWwas refreshed as well but still the same error.

    If you are in Test System, you can use function module AA_AFABER_DELETE to totally delete the depreciation area (tcode SE37, specify chart of depreciation and depreciation area), After that recreate your depreciation area and run AFBN. But before you do that, have you created a retirement transaction type that limits the posting on your new depreciation area? If not create one.
    Hope this helps.
    Thanks!
    Jhero

  • HT201250 Time machine does not recognize WD external drive

    Time machine and back-ups worked fine on my MacBookPro. It stopped working, no I believe it is still working but the MackBookPro does not recognize it and when clicking "Back up" I receive the message that the external drive is not available. Thanks to Bootcamp the computer also has a Windows side which I use mainly to run a soaring flight simulator called Condor. When I turn on the MacBookPro and click on "Choice" the window I receive shows the Mac and Windows operating systems, the Back-up and "My Passport." When I click on "My passport" it actually opens...When I turn the computer off and reboot it again there is no sign of "My Passport."
    Now, I have a second WD My Passport which I bought for the Windows side of the computer. When I attach it before turning on the computer, I shows up on Finder, however, when I click "Back up" here it seems like it is starting back-up but only for a few seconds and then I get the message that the drive is a Windows formatted drive and that a back-up cannot be completed.
    Why does the Windows formatted drive show up in Finder and also when I run the Windows side, however, the driver for the Mac does not show up on Finder?
    I now have only the Mac formatted external drive attached and I just received the following messages: Can't back up. Reformat the disk. Files can still be read but the drive can no longer be used for back-ups. Get a new external drive. Run back-ups as soon as possible.
    Can anyone help?
    Thank you.

    OK, so it sounds like you have a Mac formatted drive that you have used previously for Time Machine, and disconnected it for a few weeks, and you can now see files on it OK from your Mac. However, when the system tries to run a Time Machine backup, you get an error message "Can't backup. Reformat the disk. Files can still be read but the drive can no longer be used for back-ups. Get a new external drive. Run back-ups as soon as possible."
    I have not seen this problem before, and would recommend that you look through the Time Machine troubleshooting information at http://pondini.org/TM/Home.html
    For instance, http://pondini.org/TM/B1.html or http://pondini.org/TM/B6.html could help in your situation.  I'm assuming (but probably shouldn't) that you've verified that your hard drive doesn't need repair (another Disk Utility function) and that there is still a Time Machine backup on that drive - look for the directory Backups.backupdb.
    I hope that helps.  If not, perhaps someone with more Time Machine knowledge will pop along soon to help you further.

Maybe you are looking for