NVGRE NAT Issues with Update Rollup 5

Hello I'm looking to see if anyone is seeing the same situation when deploying a new NVGRE gateway after UR5.
In my test I have a Created a Front End Network on a Logical Switch. There is a Logical Network and Network Site is 10.0.0.0/24. I create a Front End Pool of 10.0.0.5-10.0.0.50.
I have a NVGRE Gateway provisioned to use this Front End Network and HVN Tenant Network as the Backend. All is good there.
Now I go to set the Connectivity on one of my Tenant VM Networks. I tell it to use NAT. For NAT Translation I set the IP to 10.0.0.20. Hit oK, and away it goes.
Now if I go to the NVGRE Gateway and IPCONFIG, I can see that it has created the 10.0.0.20 Address on my Front End NIC, however, it has put the Subnet Mask to
255.255.0.0 ? I'm really not sure why the IP is being created and not abiding by my IP Pool and Network Site definition which has a Subnet of 255.255.255.0?
Anyone else seeing this issue?
Thanks,
Jason

In addition, as a Test I add a new additional Add-NetNatExternalAddress on 10.0.0.21/24
Then if I Issue..
PS C:\Windows\system32> Remove-NetNatExternalAddress
Remove-NetNatExternalAddress : The requested object could not be found.
At line:1 char:1
+ Remove-NetNatExternalAddress
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : ObjectNotFound: (MSFT_NetNatExte...305f267d;0;...):root/StandardCi...ExternalAddress) [R
emove-NetNatExternalAddress], CimException
+ FullyQualifiedErrorId : Windows System Error 1168,Remove-NetNatExternalAddress
Remove-NetNatExternalAddress : The requested object could not be found.
At line:1 char:1
+ Remove-NetNatExternalAddress
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : ObjectNotFound: (MSFT_NetNatExte...305f267d;1;...):root/StandardCi...ExternalAddress) [R
emove-NetNatExternalAddress], CimException
+ FullyQualifiedErrorId : Windows System Error 1168,Remove-NetNatExternalAddress
I then reboot and I get the error
Remove-NetNatExternalAddress : Deleting IP Address 10.0.0.21 failed, Try deleting the address using
Remove-NetIPAddress.
At line:1 char:1
+ Remove-NetNatExternalAddress
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : InvalidArgument: (MSFT_NetNatExte...305f267d;1;...):root/StandardCi...ExternalAddress) [
Remove-NetNatExternalAddress], CimException
+ FullyQualifiedErrorId : Windows System Error 87,Remove-NetNatExternalAddress

Similar Messages

Issue with Update Rollup 5 for Exchange 2010 SP3 - Mailboxes that were auto mapped not working

Below is my response in another thread but creating a new one in the hopes that someone has the same issue and a solution besides mine below.
Ever since we installed Update Rollup 5 for SP3 Exchange 2010 mailboxes that were auto mapped are not accessible. They all get the same error.
Cannot expand the folder. The set of folders cannot be opened. The attempt to log on to the Microsoft Exchange has failed.
What I have been doing is removing the users permission, then adding them back using the noautomap switch in Powershell. After doing that, the user manually adds the mailbox and all is well.
Just a note here, I suspect it may have something to do with the version of Outlook 2010. We are running an older version here. I think only SP1 with no other incremental updates. Office is up to SP2. Also, one of the users I was working with could not access
the mailbox no matter what we tried but she can walk over to another workstation and open Outlook and access the very same mailbox so that pretty much proves its software related particularly with Outlook.
I cannot reproduce the problem on a workstation (XP) with a newer version of Outlook.
This has been wearing me out and I suspected the Update Rollup all long. Now I am confident as others are having the same problem. If you find out anything on how to fix this other than the steps above, let me know.

Not sure why it was suggested to use the auto mapping feature to grant permissions because that is the component that is causing the issue. Also, there is nothing wrong with the auto configuration because the user can access their own mailbox just fine and
also select mailboxes in their Outlook that were NOT auto mapped.
With that said, here is how I fixed them all.
Remove the permissions using the Exchange Console. Don't forget Send As
Wait about 15 minutes. The mailbox should disappear from the users Outlook
Open an Exchange PowerShell window and run the following command:
.\add-mailboxpermissionsnoautomap.ps1 -Identity mailbox -User user -AccessRights FullAccess
Have the user add the mailbox to their Outlook using the manual process.
All is well....
If you don't have the PS script add-mailboxpermissionsnoautomap.ps1, you can download it. I stumbled across it a few years ago and use it all the time. If you can't find it, just use the Exchange built in command for adding mailbox folder permissions but
specify automap $false.
The idea here is to grant the user access without auto mapping.

Issue with Update of Table VARINUM

Hi,
I am getting waiting Issues with Update of table VARINUM. Has anybody faced such an issue.
I have a lot of Jobs which are running in background. I am submitting it through a report. what can be the issue.
Regards,
Abhishek jolly

Thisi is quite old, but not answered properly yet, so there you go:
SAP generates a new job and temporary variant on report RSDBSPJS, for each HTTP call,which creates database locks on table VARINUM .
This causes any heavyweight BSP application to hang and give timeout errors.
The problem is fixed applying OSS note 1791958, which is not included in any service pack.

Any other realtors having issues with updating their Suprakey on their Android?

Any other realtors having issues with updating their Suprakey on their Android?

The follow is from clicking on that error number in the article cited at the end of my post:
Error 3194: Resolve error 3194 by updating to the latest version of iTunes. "This device is not eligible for the requested build" in the updater logs confirms this is the root of the issue. For more Error 3194 steps see: This device is not eligible for the requested build above.
iOS: Resolving update and restore alert messages

Having issue with update Adobe 11.0.06. Error 1603.

Having issue with update Adobe 11.0.06. Error 1603.

You should have gotten this information with the error: "Shut down Microsoft Office and all web browsers. Then, in Acrobat or Reader, choose Help > Check for Updates. See also Error 1603 | Install | CS3, CS4 products." Also, be sure you log in as the administrator and disable anti-virus.

Having issues with update to iOS 8

Having issues with update to iOS 8, wheel keeps spinning with 9 hrs remaining to complete update. What are my options?
<Re-Titled By Host>

I am a windows/mac user... And I was Linux user for several years... And so far I have been really happy with apple but this problem is frustrating.
I don't understand:
1)Why can't I go back to iOS7 since this was apparently the most stable version for my iPad ?
2) Why is apple not doing anything about it, ?
3) If the problem is that my iPad's can't fully support the features of iOS8, why on earth have they made it available to iPad 2?
Any way, I will just wait a bit longer and probably start looking in to a Samsung tablet or something....
Cheers,

Issue with updating Security Info on my Microsoft ID

I am stuck in a vicious circle trying to sort an issue with my Microsoft account.
I need to remove an old, defunct, email address and add a load of new security info however, depending on whether the date format on the page I keep being directed to is UK or US, either the updates haven’t happened or they won’t
be happening until next month – which seems ridiculous!
I’m trying to sign up for a Windows Store developer account to publish a Windows 8 app. I’m using my MSDN subscription to register for this (for free) but there is a step I can’t get past because it insists on sending a code to
my old email address – to which I have no access. It is picking up this address from my Microsoft Account Security info – however, I updated this info weeks ago. This is the screen I see (I’ve blurred out some of it as it seemed foolish to publish all my security
info J
It says my old address will be removed on 03/04/2013 and my new info added on that same date. Does anyone know if this is UK date format 3rd April – in which case it’s a long wait or a US date 4th
March in which case it didn’t happen? I’ve tried phoning 5000 and the Microsoft Customer support lines but neither of them have a clue where to start. They just keep asking me if I’ve forgotten my password – which I haven’t.
Does anyone know how I can resolve this? My only option at the moment is to wait until 3rd of April and see if anything changes – which is not ideal.
Cheers,
Rob

Hello,
The Microsoft account forum has been retired and all account related questions must now be asked online
here.
Select the issue you need help with and fill out the requested details on the next page.
You need to be signed in with a Microsoft account to access the form. If you are unable to access your primary account, you can use an alternate account (if you have one) or create a new one at
https://signup.live.com
You can read further information about blocked accounts
here.
Karl
When you see answers and helpful posts, please click Vote As Helpful, Propose As Answer, and/or Mark As Answer.
My Blog: Unlock PowerShell
My Book:
Windows PowerShell 2.0 Bible
My E-mail: -join ('6F6C646B61726C406F75746C6F6F6B2E636F6D'-split'(?<=\G.{2})'|%{if($_){[char][int]"0x$_"}})

Issue with update of BOM by Variant Config - Cost relevant indicator

Hi All VC Expert,
We are facing an issue with the update by reference characteristic of the field STPO-SANKA Cost relevancy indicator on the BOM.
We are on SAP ECC 6.0 release 700 on Oracle
Hot Package
- SAPKA70015 on ERP Cross Application componenent
- SAPKH60013 on SAP-APPL Logistics and accouting
We are using material variant
We are on the first level of configuration
Classically, we built a procedure to set X to this data base field as below :
$self.STPO_SANKA = 'X'
We assigned this procedure to the relevant items
Here is the result we have:
At the creation of the Plan Order, this is not working
At the creation of the Prod Order, this is not working
When we do a Reload PP master data, this is working very well
On CU50/VA02 when we check the trace, the procedure is executed.
Do somebody have an idea or already facing this and solve it ?
Thanks in advance for your appreciated help.

Hi Fabien. Did you solve your problem?

Issue with update to 10.6.5 and WIFI connection

I have been having an ongoing issue with my MBP over the last 6 months and even more consistently within the last several weeks.
I have searched the other posts and I think that I might be making a connection here. So, please chime in if you have anything to add to solving or addressing my problem as I think that there are others out there suffering.
Issue in short: Waking my MBP from sleep mode or turning it on loses my connection to my WIFI that is password protected.
Mainly when I wake my MBP from sleep mode this occurs a lot.
I have contacted AppleCare many times and have taken my computer to the Genius guys and I have done the following:::
Genius guys tested the computer and could not replicate. No hardware issues found, must be a software issue.
AppleCare, done many things to reset the computer, re-installed Snow Leopard, deleted Caches and other things.
Now, I am wondering if there is something actually due to the OS updates after 10.6.2 or 10.6.3 that is causing my issue that much more.
I can see my wireless router as available to join, I select it, type in my password, and it states invalid password. Try to restart, reboot, and nothing. It almost appears that it loses the sync between my keychain and such.
As of late, as I stated, the problem is more persistent now.
What do you think? An issue with the latest updates of 10.6.5?

I too often have a devil of a time connecting to a Linksys WiFi router with a brand-new unibody MacBook Pro 15", 2.66GHz. I noticed that if I boot the machine off an external Firewire drive this seems to be more of an issue than if I boot off the internal drive.
I beginning to thing there's some kind of interference between the Firewire system and the WiFi system.
The router is a Linksys with the latest firmware update. My MacBook and iPhone 3G, iPhone 4 connect to the router fine.

Performence issue with Update

hi all,
I am facing issue with below update statemetn. taking huge time to update. in xx__TEMP table I have index on Project id column. and all underlying table hase index.
Please look into plan and let me how I can reduce Cost for the blow update statement.
Thanks in advance.
UPDATE dg2.ODS_PROJ_INFO_LOOKUP_TEMP o
SET Months_In_Stage_Cnt =
(SELECT
NVL(ROUND(MONTHS_BETWEEN(SYSDATE,x.project_event_actual_date),2),0) Months_In_Stage_Cnt
FROM od.project_event x
WHERE x.project_id = o.project_id
AND event_category_code = 'G'
AND project_event_seq_nbr =
(SELECT MAX(project_event_seq_nbr)
FROM od.project_event y
WHERE y.project_id = x.project_id
AND y.event_category_code = 'G'
AND y.project_event_actual_date IS NOT NULL
AND stage_nbr <> 0
AND y.project_event_seq_nbr <
(SELECT project_event_seq_nbr
FROM od.project_event z
WHERE stage_nbr =
(SELECT current_stage_nbr
FROM od.project
WHERE project_id = x.project_Id )
AND z.project_id = x.project_Id
AND z.event_category_code = 'G'
AND skip_stage_ind = 'N'
AND project_event_actual_date IS NULL )
Plan
UPDATE STATEMENT CHOOSECost: *1,195,213* Bytes: 71,710,620 Cardinality: 41,213
14 UPDATE DG2.ODS_PROJ_INFO_LOOKUP_TEMP
1 TABLE ACCESS FULL TABLE DG2.ODS_PROJ_INFO_LOOKUP_TEMP Cost: 36 Bytes: 71,710,620 Cardinality: 41,213
13 FILTER
3 TABLE ACCESS BY INDEX ROWID TABLE OD.PROJECT_EVENT Cost: 9 Bytes: 104 Cardinality: 8
2 INDEX RANGE SCAN INDEX (UNIQUE) od.XPKPROJECT_EVENT Cost: 3 Cardinality: 8
12 SORT AGGREGATE Bytes: 16 Cardinality: 1
11 FILTER
5 TABLE ACCESS BY INDEX ROWID TABLE od.PROJECT_EVENT Cost: 9 Bytes: 16 Cardinality: 1
4 INDEX RANGE SCAN INDEX (UNIQUE) od.XPKPROJECT_EVENT Cost: 3 Cardinality: 8
10 FILTER
7 TABLE ACCESS BY INDEX ROWID TABLE od.PROJECT_EVENT Cost: 9 Bytes: 108 Cardinality: 6
6 INDEX RANGE SCAN INDEX (UNIQUE) od.XPKPROJECT_EVENT Cost: 3 Cardinality: 8
9 TABLE ACCESS BY INDEX ROWID TABLE od.PROJECT Cost: 2 Bytes: 9 Cardinality: 1
8 INDEX UNIQUE SCAN INDEX (UNIQUE) od.XPKPROJECT Cost: 1 Cardinality: 1
Thanks
Deb

882134 wrote:
Can any body give me some light why upto Select statement cost is ok, but only Update statemet is take huge 11m costing.
thanks
DebOkay so completely ignore the content of the 2 forum posts.
Why is the cost an issue for you? Without your tables, data and environment, and without a readable execution plan it's difficult to help you.
Maybe you could read the link I gave you and post some of the information it talks about up here.
p.s. read the link.

Issue with updating partitioned table

Hi,
Anyone seen this bug with updating partitioned tables.
Its very esoteric - its occurs when we update a partitioned table using a join to a temp table (not non-temp table) when the join has multiple joins and you're updating the partitoned column that isn't the first column in the primary key and the table contains a bit field. We've tried changing just one of these features and the bug disappears.
We've tested this on 15.5 and 15.7 SP122 and the error occurs in both of them.
Here's the test case - it does the same operation of a partitioned table and a non-partitioned table, but the partitioned table shows and error of "Attempt to insert duplicate key row in object 'partitioned' with unique index 'pk'".
I'd be interested if anyone has seen this and has a version of Sybase without the issue.
Unfortunately when it happens on a replicated table - it takes down rep server.
CREATE TABLE #table1
 ( PK char(8) null,
 FileDate date,
 changed bit
CREATE TABLE partitioned (
PK char(8) NOT NULL,
ValidFrom date DEFAULT current_date() NOT NULL,
ValidTo date DEFAULT '31-Dec-9999' NOT NULL
LOCK DATAROWS
PARTITION BY RANGE (ValidTo)
( p2014 VALUES <= ('20141231') ON [default],
p2015 VALUES <= ('20151231') ON [default],
pMAX VALUES <= (MAX) ON [default]
CREATE UNIQUE CLUSTERED INDEX pk
ON partitioned(PK, ValidFrom, ValidTo)
LOCAL INDEX
CREATE TABLE unpartitioned (
PK char(8) NOT NULL,
ValidFrom date DEFAULT current_date() NOT NULL,
ValidTo date DEFAULT '31-Dec-9999' NOT NULL,
LOCK DATAROWS
CREATE UNIQUE CLUSTERED INDEX pk
ON unpartitioned(PK, ValidFrom, ValidTo)
insert partitioned
select "ET00jPzh", "Jan 7 2015", "Dec 31 9999"
insert unpartitioned
select "ET00jPzh", "Jan 7 2015", "Dec 31 9999"
insert #table1
select "ET00jPzh", "Jan 15 2015", 1
union all
select "ET00jPzh", "Jan 15 2015", 1
go
update partitioned
set ValidTo = dateadd(dd,-1,FileDate)
from #table1 t
inner join partitioned p on (p.PK = t.PK)
where p.ValidTo = '99991231'
and t.changed = 1
go
update unpartitioned
set ValidTo = dateadd(dd,-1,FileDate)
from #table1 t
inner join unpartitioned u on (u.PK = t.PK)
where u.ValidTo = '99991231'
and t.changed = 1
go
drop table #table1
go
drop table partitioned
drop table unpartitioned
go

wrt to replication - it is a bit unclear as not enough information has been stated to point out what happened. I also am not sure that your DBA's are accurately telling you what happened - and may have made the problem worse by not knowing themselves what to do - e.g. 'losing' the log points to fact that someone doesn't know what they should. You can *always* disable the replication secondary truncation point and resync a standby system, so claims about 'losing' the log are a bit strange to be making.
wrt to ASE versions, I suspect if there are any differences, it may have to do with endian-ness and not the version of ASE itself. There may be other factors.....but I would suggest the best thing would be to open a separate message/case on it.
Adaptive Server Enterprise/15.7/EBF 23010 SMP SP130 /P/X64/Windows Server/ase157sp13x/3819/64-bit/OPT/Fri Aug 22 22:28:21 2014:
-- testing with tinyint
1> use demo_db
1>
2> CREATE TABLE #table1
3> ( PK char(8) null,
4> FileDate date,
5> -- changed bit
6> changed tinyint
7> )
8>
9> CREATE TABLE partitioned (
10> PK char(8) NOT NULL,
11> ValidFrom date DEFAULT current_date() NOT NULL,
12> ValidTo date DEFAULT '31-Dec-9999' NOT NULL
13> )
14>
15> LOCK DATAROWS
16> PARTITION BY RANGE (ValidTo)
17> ( p2014 VALUES <= ('20141231') ON [default],
18> p2015 VALUES <= ('20151231') ON [default],
19> pMAX VALUES <= (MAX) ON [default]
20> )
21>
22> CREATE UNIQUE CLUSTERED INDEX pk
23> ON partitioned(PK, ValidFrom, ValidTo)
24> LOCAL INDEX
25>
26> CREATE TABLE unpartitioned (
27> PK char(8) NOT NULL,
28> ValidFrom date DEFAULT current_date() NOT NULL,
29> ValidTo date DEFAULT '31-Dec-9999' NOT NULL,
30> )
31> LOCK DATAROWS
32>
33> CREATE UNIQUE CLUSTERED INDEX pk
34> ON unpartitioned(PK, ValidFrom, ValidTo)
35>
36> insert partitioned
37> select "ET00jPzh", "Jan 7 2015", "Dec 31 9999"
38>
39> insert unpartitioned
40> select "ET00jPzh", "Jan 7 2015", "Dec 31 9999"
41>
42> insert #table1
43> select "ET00jPzh", "Jan 15 2015", 1
44> union all
45> select "ET00jPzh", "Jan 15 2015", 1
(1 row affected)
(1 row affected)
(2 rows affected)
1>
2> update partitioned
3> set ValidTo = dateadd(dd,-1,FileDate)
4> from #table1 t
5> inner join partitioned p on (p.PK = t.PK)
6> where p.ValidTo = '99991231'
7> and t.changed = 1
Msg 2601, Level 14, State 6:
Server 'PHILLY_ASE', Line 2:
Attempt to insert duplicate key row in object 'partitioned' with unique index 'pk'
Command has been aborted.
(0 rows affected)
1>
2> update unpartitioned
3> set ValidTo = dateadd(dd,-1,FileDate)
4> from #table1 t
5> inner join unpartitioned u on (u.PK = t.PK)
6> where u.ValidTo = '99991231'
7> and t.changed = 1
(1 row affected)
1>
2> drop table #table1
1>
2> drop table partitioned
3> drop table unpartitioned
-- duplicating with 'int'
1> use demo_db
1>
2> CREATE TABLE #table1
3> ( PK char(8) null,
4> FileDate date,
5> -- changed bit
6> changed int
7> )
8>
9> CREATE TABLE partitioned (
10> PK char(8) NOT NULL,
11> ValidFrom date DEFAULT current_date() NOT NULL,
12> ValidTo date DEFAULT '31-Dec-9999' NOT NULL
13> )
14>
15> LOCK DATAROWS
16> PARTITION BY RANGE (ValidTo)
17> ( p2014 VALUES <= ('20141231') ON [default],
18> p2015 VALUES <= ('20151231') ON [default],
19> pMAX VALUES <= (MAX) ON [default]
20> )
21>
22> CREATE UNIQUE CLUSTERED INDEX pk
23> ON partitioned(PK, ValidFrom, ValidTo)
24> LOCAL INDEX
25>
26> CREATE TABLE unpartitioned (
27> PK char(8) NOT NULL,
28> ValidFrom date DEFAULT current_date() NOT NULL,
29> ValidTo date DEFAULT '31-Dec-9999' NOT NULL,
30> )
31> LOCK DATAROWS
32>
33> CREATE UNIQUE CLUSTERED INDEX pk
34> ON unpartitioned(PK, ValidFrom, ValidTo)
35>
36> insert partitioned
37> select "ET00jPzh", "Jan 7 2015", "Dec 31 9999"
38>
39> insert unpartitioned
40> select "ET00jPzh", "Jan 7 2015", "Dec 31 9999"
41>
42> insert #table1
43> select "ET00jPzh", "Jan 15 2015", 1
44> union all
45> select "ET00jPzh", "Jan 15 2015", 1
(1 row affected)
(1 row affected)
(2 rows affected)
1>
2> update partitioned
3> set ValidTo = dateadd(dd,-1,FileDate)
4> from #table1 t
5> inner join partitioned p on (p.PK = t.PK)
6> where p.ValidTo = '99991231'
7> and t.changed = 1
Msg 2601, Level 14, State 6:
Server 'PHILLY_ASE', Line 2:
Attempt to insert duplicate key row in object 'partitioned' with unique index 'pk'
Command has been aborted.
(0 rows affected)
1>
2> update unpartitioned
3> set ValidTo = dateadd(dd,-1,FileDate)
4> from #table1 t
5> inner join unpartitioned u on (u.PK = t.PK)
6> where u.ValidTo = '99991231'
7> and t.changed = 1
(1 row affected)
1>
2> drop table #table1
1>
2> drop table partitioned
3> drop table unpartitioned

Are there any issues with updating to IOS 5.0.1

I have a brand new IPad 2 and I see there is an OS update available. I see there are issues with some IPhones, but I'm wondering if there is any reason not to update the OS on my IPad?

I haven't had any issues, although posts in this forum show some have. To upgrade to iOS5 you need to have your iPad connected to your computer. Once iOS5 is installed, further iOS updates can be installed via WiFi connection.
You can download a complete iPad 2 User Guide here: http://manuals.info.apple.com/en/ipad_user_guide.pdf
 Cheers, Tom

Any known issues with updating to the Windows 8.1 RTM?

The Windows 8.1 RTM is finally on MSDN. I was looking to run the update and wanted to see if anyone has upgraded and see if anyone has seen any issues with CC.

In case anybody else is using Windows 8.1 on 3200 x 1800 resolution and experiencing the same problem, I think I may have found a workaround. At least on this laptop (Dell XPS15) I can right
-click on the EDQ application in the Start Menu and choose to Run with graphics processor / High - performance (NVIDIA) processor. This appears to render the EDQ canvas with sympathetically sized fonts making the processes, and the attributes within processors, readable again.
I would be interested to hear if anybody has some Java font parameter that can be set to control the font size on Java applications, but for now the problem I had appears to be solved.

Torch 9800 Issues with updating software

Hi there I'm new to this forum and to BB.
I have been having issues with my Torch for a couple of weeks now, firstly I had issues with it when it was charging the red light and not coming on, but managed to get it to work after a bit of searching on here.
This happened regularly over the past week, then today I have the Error 507 message.
I have used Desktop Manager v5.0.1 to try and update it but I didn't have the password for the phone and after 10 attempts it wiped the phone which I wasn't really bothered about.
I am now trying to update the software but when I get to the Device Application Selection page it says that I have don't have any space left.
Is there any way around this so that I can update the phone's software?
Any help would be much appreciated.
Clwyd

Hi! Welcome to the forums.
Please keep us posted and goodluck.
Click if you want to Thank someone. If Problem is resolved, so that others can make use of it.

Issues with updating!! Help!!

I got the App 200 Error and am trying to update the OS, but my desktop manager keeps saying that I have connection issues with the internet and won't let me update. Is there something I can do??

Are you doing a web-based upgrade or are you going through the BlackBerry Desktop Software?
If you have tried both of those options, and are still having issues have a look at the link below. This link will explain how to perform a clean application load of the BlackBerry device Software.
How to perform a clean reload of the BlackBerry Device Software using BlackBerry Desktop Manager for Windows - KB11320
http://www.blackberry.com/btsc/KB11320
Hope this helps.

NVGRE NAT Issues with Update Rollup 5

Similar Messages

Maybe you are looking for