Online gaming issue with WRT54G2V1.

Hi
I have a WRT54G2V1 (firmware 1.1.01) router hard wired to 4 computers in the house. I have a Siemens Speedstream 4200 Series Modem.
I play Mechwarrior IV and I have some connection problems. The MW4 sites say to do the following:
Make a static LAN IP address - This I have done to IP 192.168.1.185, and confirmed it with the ipconfig command
I have disabled all firewalls and anti virus etc
I port forward the following ports 27999, 2300-2400, 47624, 28800-28810 through the router panel on the port forwarding page
They also say to disable Upnp - which when I do this the connection lasts about 2 minutes and then freezes
I run a port checker and It has always said that the ports are closed. I have power cycled the router many times to checkk each stage of the settings changes and thank god for the reset button. I have also power cycled the modem at times too. Nothing seems to get the ports open.
I will post the screenshots of the abovementioned screens in the next 24hrs when I figure how to.
The game connects to the lobby but I can't join any of the selected games.
PLease help and ask for any other info if you need

As you have already open the Ports on your Router, and it still dosent work, i think in this case you need to upgrade the firmware of your Router. Go to website linksysbycisco.com/downloads.........insert model no of your router in serach tab......select proper version of your router........download the firmware file......save that file on desktop...
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...
In the address bar type - 192.168.1.1...Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
Note : Also make sure that your computer is set to obtain IP automatically, disable any firewalls, security softwares on the computer before trying to access the setup page...

Similar Messages

My online gaming issues

I got a Linksys WRT310N wireless router about 14 months ago. My computer, modem and router are upstairs and my TV, PS3 and Xbox 360 are downstairs. Everything was working fine until late February. One Sunday I couldn't get online with my Xbox. I figured it was just an issue at the moment with Live, but the following weekend I couldn't get online on Saturday or Sunday and it just kept getting worse in the weeks to follow.
During the time the PS Network was down I found I was able to get online with my 360 by jumping on other people's networks in my area that didn't need a password. The connection wasn't always great but at least it was something.
When the PS Network came back up I got serious about getting everything straightened out so I tried changing a bunch of settings on my router. All of the common suggestions: static IPs for consoles, port forwarding, etc. I was able to get on both consoles with my own network again, but it was way too slow to do anything. Images/icons wouldn't load and I couldn't download anything. Then last Saturday I tried adding my PS3 MAC address to the MAC filtering on my router's configuration page. After, I went to see if that did anything. I tried to download a Netflix update that I couldn't even come close to downloading before and it downloaded in like 5 seconds. So then I put my Xbox MAC address in too and Xbox Live worked great after. So it looked like my problem was solved.
The following morning I turned on the computer to go online and my connection speed showed that it had limited or no connectivity. I unplugged my modem and router, waited a bit, and plugged them back in, but it didn't solve anything. So I decided to just leave it alone for a while, thinking it might just be an issue with Time Warner for the moment. I went back 2 hours later and nothing had changed. It said the network did not assign a network address to the computer. I decided to give Time Warner a call.
After I told the woman I was speaking with that I already tried unplugging my router and modem she suggested I reset my router. I really did not want to do this as I had already spent so much time with it trying to get my gaming straightened out and I didn't want to lose the settings that were working for me the previous day. But it didn't really seem I had a choice and I was pretty sure I remembered all of the settings changes I made. So I reset the router and my internet connection for the computer was back.
So I went back in my router and made all of the changes for my gaming again and went to try both consoles. Both could get online but images/icons take forever to load again so I can't really do anything online and a few days later my computer was back to the "limited or no connectivity." I've reset my router countless times and tried changes in the settings but I still can't get anything to work for my consoles again. When I check my PS3 connection the signal strength is 95-100% but when I run the connection test it always fails when it gets to upload and download connection speeds. What are my options at this point? It is very frustrating.

Everything looks good, except I'm not sure why your PC lists the dns servers as 192.168.1.1. The only time I see a pc list the dns servers as the router's ip are when someone has loaded dd-wrt onto their router and when they have selected dns masq. But you're still able to surf the web so I wouldn't worry about it. Since you have cable, all you should've had to do was select dhcp as the internet connection type and turned on upnp. Could you run ICET on internet explorer and see if you get any errors.
PS: IF you still can, edit out your default gateway that you posted under status page. You usually want to keep that private.
I don't work for Cisco. I'm just here to help.

Online video issue with OS 2.0.0.7111

I have an issue with OS 2.0.0.7111. I can only view one online video (youtube, vimeo, etc...) successfully upon which if I try to view any other video my broswer crashes and becomes unresponsive. When I close the browser the icon is permanently greyed out and the only way to get it back is to do a hard reset. I've tried doing a security wipe, reverting back to OS 1.0 then reinstalling OS 2.0 and I still have the problem. I thought it was initially a flash problem but I enrolled in the html5 program for youtube and it still occured. I recorded a video of my issue so you can have a better idea of what happens.
http://www.youtube.com/watch?v=ikkNr5J9sWU
Any thoughts on a solution?

have your tried a different wifi router or hotspot?
have you rebooted your wifi router?
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

Gaming issues with K7N2G

K This is weird to me I think I might already know the root of the problem but looking for some verification from you all.
I have a new system using
K7N2G
AMD 2400+
ATI Radeon 9700 PRO
1gb Kingston Hyper X Ram
Pioneer DVD-Rom and Plextor CD-RW
Sound Blaster Audigy 2
Seagate 40 GB 7200 RPM 2mb cache drive
Western Digital Special Edition 40GB 7200 RPM 8mb cache drive
OS is installed on on WD and just use the Seagate for backups.
System is really really fast however, whenever I play games I keep getting these weird hanging moments when loading things and every game I have loaded and played crashes, installed everthing from Red Alert2 to MOHAA. I can play for awhile but it doens't seem to last longer than about 30 min or so. My guess is that there is an issue with having the 2 drives on the same IDE channel. Not sure what difference that would make but that's my guess.
Any thoughts?

This is a RAM incompatibility issue. I recently went through almost the same problem. All you can do is use different ram. I went with Kingston Value RAM. I have the K7N2G-ILSR. I had to update bios to 1.3 to fix compatibility. I tried the board with Samsung, Corsair, and Crucial. The Samsung would not work, but both Corsair and Crucial work well. Good Luck.

How to fix Online help issue with F1

Dear All,
I think you already know this issue : when using a proxy, Online help is not working on Adobe Reader XI.
message displayed : "Online Help content cannot be displayed. Verify you can launch your web browser and have access to the Internet."
I already checked on this forum and tried some things to fix this, but without any success :
- try to add the registry key FeatureState -> not working
- check if IE is correctly defined as default browser -> it is
Accessing Online help from the Help menu was by passed by the following .js :
app.addMenuItem({
cName: "MyHelp", cUser: "Adobe Reader XI Help...",
cParent: "Help",
cExec: "app.launchURL('http://helpx.adobe.com/reader.html');",
nPos: 0
But, the message still appears when pressing F1 shortcut.
Details : Adobe reader 10.0.06 packaged through an administrative installation et customized with Adobe Customisation Tool
I tried to install directly from the setup.exe to be sure that was not caused by my package, and the issue is still the same.
I'm an application packager for the European Court of Auditors and we want that Help works through F1 shortcut. This is mandatory for me.
Thank you in advance for your help.

Timo Hahn wrote:
There is a problem with autoHeightRows and columnStretching used together in 11gR1.
Have you tried without columnStretching?
Or have you tried if it works in 11gr2?
TimoHi Timo, Thank you very much for taking time to respond to my question.. :)
Back to my question...
I tried removing the columnStretching although my requirement really requires this but no effect really happens even if I remove this.
Based on my investigation on the generated HTML, I notice the following items:
1. A table is being wrapped in a div that is being set at a fixed height.
2. On first load, if your autoheight rows is set to 6, the framework is setting a height of 96px to the div. This height would almost cut the last row of the table.
3. If you try to refresh the page or try to re-PPR the component, the framework resets it to 102px which causes the last row to be fully displayed.
My only concern is that IE is perfectly displaying this while Chrome and FF are having problem.
Based on my understanding, the framework is messing up the height only on first load. Not sure but this is how I see it. I am really not confident also on my findings
and I would most likely hear other's comment.
Thanks.

Online Albums Issues with PSE7

Does PSE7 offer a way to save online albums directly to my hard drive instead of just uploading them to Photoshop.com or to another website via FTP? Unlike PSE6, PSE7 doesn't seem to offer that option (at least, I couldn't find it)
And can anyone tell me what happened to all the standard, medium thumbnail online album templates (for example, black background with matrix of thumbnails on left with single large image on right)? PSE6 offered them, but PSE7 doesn't.
Must I purchase a Photoshop.com PLUS membership ($50) to get these templates (which came free with PSE6)? If so, how often are new templates delivered. The website just says "you'll get new templates delivered to your software on a regular basis?" Does that mean daily? weekly? monthly? semi-annually??
I really appreciate any help you all can give me!

Exactly!
PSE7 doesn't seem to be an upgrade at all
it seems to offer FEWER features than PSE6
with never-ending plugs for photoshop.com plus membership
I plan to downgrade to PSE6 to get the template I want
and to be able to save my projects directly to my hard drive
see the answer (and my reply) to the same post in the Technical Issues section
or just click here
http://www.adobeforums.com/webx/.59b705f0/3
Thanks very much for your input!

Gaming Issue with new 17" iMac (got it 3 days ago)

This has happened about 6 times now while playing the starcraft on my new 17" iMac computer. While playing all of a sudden the game will crash and give me a error message which says that due to a unknown error the application starcraft has been forced to close...I just bought this computer because I heard they are more reliable then PC's but what is going on, I really don't know where to post this question but the game requires the cd-rom to be in the drive to play it so I don't know if it is a cd-rom problem or problem with the actual computer...please help me out here.
The game is 10 years old now so it shouldn't be a compatability issue.
System information:
Hard Drive - 500gb
Ram - 2 gb
Processor - dual core 2.16
CD Drive - Superdrive
if you need to know anything else just let me now.

Contrary to what you might think, it's most certainly a compatibility problem. Imagine running a 10-year-old DOS game on Windows Vista or XP, doesn't matter how fast/reliable the OS is, there are bound to be problems.
You have the Mac version with latest updates, but you are still running a 10-year old game on a non-native system (it ran in System 9 when it first came out). It's still powerpc app that need to be translated at run-time to run on your intel Mac. If it runs, fine, if it doesn't, it's not supported anyway. You have to ask Blizzard see if they will release universal binary updates (not very likely).
Or, like suggested above, get the windows version since you can have windows in bootcamp.
Regarding performances, I'm running a 3-year-old game Homeworld 2 in rosetta, and it's perfectly playable, so rosetta is actually quite fast now.

Having issues with PC gaming and my Linksys AC1900 router! (What settings should I be using?)

Well I recently purchased a linksys AC1900 for a better/faster connection with my internet. Sadly, I have been having issues with online gaming. I am attempting to play a blizzard game (Diablo 3) but its not letting my connect. I did a direct wired connection and it worked just perfect. However, I dont want to play in my garage...lol. Does anyone have any ideas what settings I should be using? It lets me connect to battlenet but when my character loads into the world I get disconnected. I tried opening ports, shutting off uPnP, and various other things. Is the the router or is it me? Someone please help!

I got confused with your response. If you are still having the same challenge, make sure you have enough speed to play any online game. You may also try to reboot your PC and the router. If the result is the same, check if the firmware is up to date. You may try to manually update it on the Linksys Smart WiFi page. Here's how. Once accomplished, reset, reboot, and reconfigure the router. I hope this helps!

HP Envy 15-j075nr - Issues with gaming performance (slow-motion gaming)

SPECS:
Display: 15.6" diagonal HD BrightView LED-backlit display (1366 x 768)
Memory: 8GB installed memory
Hard drive: 750GB 5400RPM hard drive with HP ProtectSmart Hard Drive Protection
Processor: AMD Elite Quad-Core A10-5750M Accelerated Processor
Operating system:Windows 8
Graphics card: AMD Radeon HD 8650G graphics with up to 4204MB total graphics memory
Running on the exact specs above, I'm playing games via Steam (Tomb Raider, Saints Row IV, Dishonored, etc) and have had to compromise video/display quality settings just to get the games to play correctly. Most games have an auto-detect feature for display and audio settings and in each instance the games are set to Ultra or High settings. But when I begin to the play the games with the default settings that games are extremely slow, though the graphics look great.
Given the specs above and the fact that the games auto detect at the highest or near to the highest settings, might I have an issue with my current system settings that I could tweak in order to get a higher quality gaming experience? I feel like these settings are definitely good enough to get at least HIGH display quality, but that has yet to work.

Hi @trickster878
I understand you are having performance issues with games on your notebook computer, but really notebook computers for the most part are not intended to be gaming machines. Their design focus is more to be light weight and portable while also providing the ability to run for two hours or more without a power connection when fully charged.
Many of the things that make for a good gaming machine are sacrificed in a notebook. All that being said, it is possible to play many games on notebooks, but rarely as well as it would work on a desktop computer.
It is likely that you can tweak the settings to get a compromise that is more playable, but it is often a robbing Peter to pay Paul situation. Something may have to be sacrificed.
You can take a look at these pages and see if anything helps.
Computer Locks Up or Freezes When Playing a Game
HP PCs - Improving System Performance without Adding Memory (Windows 8)
Otherwise, you would probably need to look at the video settings in each of the games you are trying to play. The settings will need to be customized for each of them, and you may have to look at the pages/forums for the individual game to see which setting may have to be changed internal to that game.
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Issues with my connection when gaming (Insurgency)

Hello,
I just bought the MSI GT72 2QE. I am very pleased with de specs like the Geforce GTX 980m and the i4710hq but there is an issue that is bothering me some days now. When i am playing my beloved game Insurgency, i get ping spikes all the time. So i followed up some instruction on uninstalling the Killer software suite and just installing the drivers when i encountered the next problem. My Killer Wireless-n/a/ac 1525 Wireless Network Adapter couldn't find the drivers in the 'drivers only' package. But i did my best to find other drivers and accomplished after 5 hours full of frustration. So that is done but still doesn't solve my problem.
I don't know what to do anymore and I'm starting to think that maybe my Killer Wireless-n/a/ac 1525 Wireless Network Adapter is the issue. Maybe this is a hardware issue. I contacted the store where i bought it and they will contact me in 48 hours with a possible solution but the guy said that after all my effort it seems like a hardware issue indeed. You guys are my last hope or my laptop will be gone for 3 weeks at the factory.
Video of ping:
nl.tinypic.com/r/ztisd1/8
I hope someone has the solution.
Excuse me for my incorrect English, it's not my native language.
Bye!

Thanks for your reply.
I'm glad (and I'm not glad for the others..) that I'm not the only one. But it's not because there are more devices connected to my router because I am the only one now and I'm still having this problem while my other laptop doesn't have any problems at all. I've tried everything so far now. Resetting my router, restarting my router, reinstalled windows, reinstalled drivers, got rid of the software suite, turned off firewalls, virusscanners etc. Everything.
I thought it was only with Insurgency but it's also bugging me with Battlefield 4.
So i have tried and done everything i could find on every forum on the internet. Still I don't get the download/upload/connection I am used to when using wireless. When i am in my room, which is 10m away from the wireless router, my download speed is max 1200 kb/s where I would easily get 2300 kb/s. Also when playing online games I am having big issues with my latency/ping. It goes from 60 to 200 to 400 and back every 15/20 seconds. I also own a Asus laptop and I don't have any issues at all with the wireless connection. When I am in my room there are no problems at all. I am starting to think that the Killer Wireless adapter is just a f*cked up thing. I bought a laptop (GT72 with 980m) for €2300 but I am having all these issues with the connection. It makes me really frustrated.
Longer vid of ingame netgraph:
nl.tinypic.com/r/97mjae/8
I am hoping that there is something that solves my issues. I'm starting to think that another wireless network adapter from another brand is the only option. Is there an option to change the wireless network adapter on my laptop because I will if I can. This piece of sh*t needs to be replaced.
Bye

X99S GAMING 9 AC Not booting - Debug 94 code - Issue with GTX 980 SLI in WoW

Hello, I bought the X99S GAMING 9 AC motherboard but have ran into some issues.
The computer won't boot when I put my second MSI GTX 980 Gaming 4 GB card in the last PCEI 3.0 port (PCIE port 5) and I get the debug LED message 94 on the motherboard. I have a SLI setup.
The first card I have in the second PCIE 3.0 port due to the Noctua U14S CPU fan takes up space for the first slot. So I have been running my grafic cards in PCIE slot 2 and 4 with some issues.
First the card in slot 2 gets really warm over 86 celsius. And second: SLI runs really poorly in World of Warcraft. I get a lot higher performance with just one card activated. I am not sure if it's cause I am not running my cards in the recommended PCIE 3.0 ports or because WoW has some issues with SLI, but I heard other people have no issues at all with WoW in SLI.
I got the same issue with 3Dmark firestrike, the cards perform really poor in SLI. I get higher score with SLI turned off..
Though SLI seems to run pretty well in 3dmark 11 and Diablo 3 Reaper of Souls.
But the main issue right now, is that the computer won't boot with the grafic cards in PCIE port 2 and 5. The solution to run them next to each other is not good, cause it gets really hot and I get bad performance in WoW and Firestrike.
Picture of my setup before I switched places with the grafic cards as you can see, it is really tight:
Any upcoming bios updates (got v1.3) that will solve this issue on the horization? Hopefully this get sorted out really soon..
My whole computer setup:
Intel i7 5820K | MSI X99S Gaming 9 AC (bios 1.3) | SLI MSI GTX 980 Gaming 4GB | Samsung 850 Pro 512 GB | WD Red 4TB | G.Skill Ripjaws DDR4 3000MHz 4x4GB | EVGA SuperNOVA P2 1000W | Noctua NH-U14S PnP | Fractal Design Define XL R2 | 5 Noctua NF-A14 PWM 140mm fans | Windows 7 Pro 64 bit

You must use the recommended PCIE slots as the manual says for your CPU type, PCIE #1 and PCIE #4 if I remember, just open the manual :P for optimal 2Way SLI, also your 5820k will limit to 28 pcie lanes only if you plan to add more vgas...the other problem is your giant CPU air cooler blocking PCIE#1, do a favor to yourself, buy a watercooler for your 5820k and your problems are gone, add some overclock in your system, low noise and better temps.
Here I use 3x980 in SLI with X99S Gaming 9 AC, going soon to WC the VGAs with EK blocks.....3way is far more temperature critical than 2way spaced one.
Cheers

HP Officejet 4500 Wireless Printing Issues with Online Maps & Financial Institutions

I have an HP Officejet 4500 Wireless printer that I have wireless connection to my HP G72 Laptop running Windows 7 (64 bit) with Internet Explorer 9. I am having trouble printing online maps from either Bing Maps or Google Maps. It seems the print jobs get stuck in the print que and always show an indefinite status of “Printing” in the que but never get printed.
I’ve tested my other applications including Office 2010 and all other jobs seem to print just fine. I do use the “Print” button located in each of the online Map sites (Bing, Google). This is when the jobs get stuck.
I do also have the HP Bing Bar installed with Smart Print. The Smart Print feature seems to work with the online maps just fine (seems I’ll just use it instead).
Another separate printing issue is that I can never get any of my online financial transactions to print from any of my online financial institutions with either the Internet 9 print features or the HP Bing Smart Print feature. I can never get those to print (have to wait for the PDF statements to be available).
Any ideas as to why I can print the maps or online financial transaction? I get no error messages either.

Hi,
Please use the following tips/instructions to fix:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02221706&cc=us&lc=en&dlc=en
Good luck.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

RDP Users seeing display issues with SharePoint Online Template

I originally posted this in the SharePoint Online forums, but they referred me to the RDP forums as it appears to be an issue with RDP, not SharePoint Online: Original
Post
I've been able to verify this only happens in RDP when opening a Word Template with embedded Excel table from SharePoint Online within the local Word 2010 application.

Amy,
Thank you for the input. Its rather odd, but it appears the users who are seeing this problem are connecting via RDP on laptops with widescreens, with screen resolution set much higher than the 1290x1084 we use on the terminal servers. Turning
the resolution down on the laptops did keep the table from becoming oversized and most of it running off edge of document.
However, it appears even turning down the resolution of the client machine still affects how the font is displayed in the document. The font size and type are different than the template document, they get saved that way and appear that way to other users
who do have their screen resolution set correctly. It seems there is something else going on here, thoughts?

Hi, Using MAC OSX 10.6.8 and have intermittent issues with receiving new emails - sending is OK. I've tried the workarounds (take offline & take online), quitting mail etc - no luck. Any suggestions?

Hi, I'm using MAC OSX 10.6.8 and have intermittent issues with receiving new emails - sending is OK. I've tried the workarounds (take offline & take online), quitting mail etc - no luck. Have cleared space, checked Window - Doctor and server has green light. Mail Activity shows 47 emails waiting to download, iPad and iPhone download them all OK - no extra big files stopping the download either. In the past, quitting mail has worked, but not today... Any suggestions?

Hi, I'm using MAC OSX 10.6.8 and have intermittent issues with receiving new emails - sending is OK. I've tried the workarounds (take offline & take online), quitting mail etc - no luck. Have cleared space, checked Window - Doctor and server has green light. Mail Activity shows 47 emails waiting to download, iPad and iPhone download them all OK - no extra big files stopping the download either. In the past, quitting mail has worked, but not today... Any suggestions?

Online Streaming Authentication issues with Chrome

I get caught in a never ending login loop when I try to authenticate with my Verizon ID for online streaming services such as stream.nbcsports.com/liveextra, stream.golfchannel.com, nflonline.nfl.com, etc. Others have reported the same issue with showtime's online streaming service. I have cookies enabled and I continue to get caught in login loops when I'm using Chrome. I do not have the same issue with Internet explorer or Mozilla Firefox. This has been reported before but it doesn't seem to be a high priority. Please fix this issue ASAP.
Solved!
Go to Solution.

Looks like its an issue with the built in "Pepper" Flash player in Chrome. I disabled the built in Chrome flash player and enabled the system flash player and all my authentication issues have gone away on Chrome. WatchESPN, NBC Sports Live Extra, Watch NFL Network all work now.
Verizon...please work with Google on a permanent fix for this!!!
To anyone else having authentication issues on Chrome... use this link to disable the pepper flash player: http://newtriks.com/2012/12/01/how-to-disable-the-chrome-pepper-flash-player/

Online gaming issue with WRT54G2V1.

Similar Messages

Maybe you are looking for