Only run Group Policy when computer is on the correct IP range

Hi,
We are using 802.1x via Cisco AnyConnect NAM. The Windows machines are authenticating quickly enough for Group Policy to run properly.
Is their a way to make Group Policy run only when the computer is on the correct IP range. We have the Group Policy set to only run once the network starts, but with the 802.1x the computers land in a guest network, so the network has started, just the wrong
one.
Best wishes
Michael

Hi Michael,
>>Is their a way to make Group Policy run only when the computer is on the correct IP range.
For this question, the suggestions provided by Don are reasonable.
Regarding this point, the following thread and article can also be referred to for more information.
GPO WMI Filter range of IP Addresses
https://social.technet.microsoft.com/Forums/windows/en-US/94a1f90b-3cc0-4800-80ba-9f5fa892efeb/gpo-wmi-filter-range-of-ip-addresses
Preference Item-Level Targeting
https://msdn.microsoft.com/en-us/library/cc733022.aspx
IP Address Range Targeting
https://msdn.microsoft.com/en-us/library/cc732310.aspx
>>A GPUpdate /force asks for a reboot and this will then take me off the network once more.
Because of fast logon optimization, some group policy settings like folder redirection, software installation, and drive mapping need us logon twice to get them applied successfully.
Description of the Windows Fast Logon Optimization feature
http://support.microsoft.com/en-us/kb/305293Best regards,
Frank Shen
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Similar Messages

After syncing and updating my iphone my iCalendar on my computer lost most of my information. Including wiping out an entire calendar group. When trying to readd the calendar group it won't let me add events to my calendar under that category.

After syncing and updating my iphone my iCalendar on my computer lost most of my information. Including wiping out an entire calendar group. When trying to readd the calendar group it won't let me add events to my calendar under that category. A message pops up that says: "You can't add events or to do items to a calendar group. Select an individual calendar in the calendar list, then create your events or to do items." Any help here would be greatly appreciated! I would like to either retrieve the old information or find a way to add the category back in to start over. Thanks in advance!

hi i had the same problem today when i updated my itunes to latest version. however, i have just found my songs in the 'itunes media' folder. this was accessed through 'my music' then keep clicking through until you find itunes media and all my library songs were in there and i then just added these files to my library and all were restored however, i have lost all my playlists but at least my 700 songs are back. very dissapointed with apple that they have let this happen with their latest update, the previous version was miles better than this one . hope you find them. stevo

To disable group policy when the machine not connected to domain controller

hi all
i have alot of users joined to the domain and i enabled prevent user to to add/ remove sites on the trusted sites option through group policy, is there any script file that allow user to add and remove sites from the trusted sites when he/she out
of LAN without interaction by user, or script to disable all group policy settings that applied by the active directory administrator when there is no connectivity between domain machine and the active directory.
regards

Duplicate post...
http://social.technet.microsoft.com/Forums/en-US/winserverGP/thread/617a7ddb-592e-481f-b360-23d871eb26be#617a7ddb-592e-481f-b360-23d871eb26be
Martin
Mal ein
GUTES Buch über GPOs lesen?
NO THEY ARE NOT EVIL, if you know what you are doing:
Good or bad GPOs?
And if IT bothers me - coke bottle design refreshment :))

I have a mid-2011 iMac running Mavericks. When I click restart the computer goes to a white screen with a spinning circle and does not go any further until I hold down the power button to turn it off. What do I do?

I have a mid-2011 iMac running Mavericks. When I click restart the computer goes to a white screen with a spinning circle and does not go any further until I hold down the power button to turn it off. What do I do?

Ok, sounds like the safe mode boot worked... You probably don't want to always be in safe mode though (some reduced functionality) so does it do a normal boot now? If not, you should then reboot into safe mode and run Disk Utility. Then select Macintosh HD on the left hand side, and click the Verify Disk button. If needed, it will ask you to Repair Disk. If there are errors found, Repair Disk again until there are none. Then try another normal boot and reply with result, wether good or bad.

Every time I update firefox it will only run updater.exe when I try to restart

every time I update firefox it will only run updater.exe when I select firefox to run. The only way around this that I have found so far is to do a fresh install of firefox.

Create a new profile as a test to check if your current profile is causing the problems.
See "Creating a profile":
*https://support.mozilla.org/kb/profile-manager-create-and-remove-firefox-profiles
*http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Profile_issues
Profile Backup and Restore
*http://kb.mozillazine.org/Profile_backup
*https://support.mozilla.org/en-US/kb/back-and-restore-information-firefox-profiles
*http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

I bougth a macbook used from another person. I already set all accounts to my apple id, but only in APP STORE, when I try download the new version of a app, it request the old apple id from the another guy. I already terminate the session and init another

I bougth a macbook from anotner person.
I already change th apple id in all places.
But only in app store when I choose download the new release of a app, it request the password of the old apple id, and i can't switch this apple id to my apple id.
Where i should change for this?

The first thing to do with a second-hand computer is to erase the internal drive and install a clean copy of OS X. You — not the previous owner — must do that. How you do it depends on the model, and on whether you already own another Mac. If you're not sure of the model, enter the serial number on this page. Then find the model on this page to see what OS version was originally installed.
1. You don't own another Mac.
If the machine shipped with OS X 10.4 or 10.5, you need a boxed and shrink-wrapped retail Snow Leopard (OS X 10.6) installation disc from the Apple Store or a reputable reseller — not from eBay or anything of the kind. If the machine has less than 1 GB of memory, you'll need to add more in order to install 10.6. Preferably, install as much memory as it can take, according to the technical specifications.
If the machine shipped with OS X 10.6, you need the installation media that came with it: gray installation discs, or a USB flash drive for some MacBook Air models. For early MBA models, you may need a USB optical drive or Remote Disc. You should have received the media from the previous owner, but if you didn't, order replacements from Apple. A retail disc, or the gray discs from another model, will not work.
To boot from an optical disc or a flash drive, insert it, then reboot and hold down the C key at the startup chime. Release the key when you see the gray Apple logo on the screen.
If the machine shipped with OS X 10.7 or later, you don't need media. It should boot into Internet Recovery mode when you hold down the key combination option-command-R at the startup chime. Release the keys when you see a spinning globe.
2. You do own another Mac.
If you already own another Mac that was upgraded in the App Store to the version of OS X that you want to install, and if the new Mac is compatible with it, then you can install it. Use Recovery Disk Assistant to create a bootable USB device and boot the new Mac from it by holding down the C key at the startup chime. Alternatively, if you have a Time Machine backup of OS X 10.7.3 or later on an external hard drive (not a Time Capsule or other network device), you can boot from that by holding down the option key and selecting it from the row of icons that appears. Note that if your other Mac was never upgraded in the App Store, you can't use this method.
Once booted in Recovery, launch Disk Utility and select the icon of the internal drive — not any of the volume icons nested beneath it. In the Partition tab, select the default options: a GUID partition table with one data volume in Mac OS Extended (Journaled) format. This operation will permanently remove all existing data on the drive.
After partitioning, quit Disk Utility and run the OS X Installer. You will need the Apple ID and password that you used to upgrade. When the installation is done, the system will automatically reboot into the Setup Assistant, which will prompt you to transfer the data from another Mac, its backups, or from a Windows computer. If you have any data to transfer, this is usually the best time to do it.
Then run Software Update and install all available system updates from Apple. To upgrade to a major version of OS X newer than 10.6, get it from the Mac App Store. Note that you can't keep an upgraded version that was installed by the previous owner. He or she can't legally transfer it to you, and without the Apple ID you won't be able to update it in Software Update or reinstall, if that becomes necessary. The same goes for any App Store products that the previous owner installed — you have to repurchase them.
3. Other issues
If you see a lock screen when trying to boot from installation media or in Recovery mode, then a firmware password was set by the previous owner, or the machine was remotely locked via iCloud. You'll either have to contact the owner or take the machine to an Apple Store or another authorized service provider to be unlocked. You may be asked for proof of ownership.
If the previous owner "accepted" the bundled iLife applications (iPhoto, iMovie, and Garage Band) in the App Store so that he or she could update them, then they're linked to that Apple ID and you won't be able to download them without buying them. Reportedly, Mac App Store Customer Service has sometimes issued redemption codes for these apps to second owners who asked.
If the previous owner didn't deauthorize the computer in the iTunes Store under his Apple ID, you wont be able to authorize it immediately under your ID. In that case, you'll either have to wait up to 90 days or contact iTunes Support.
When trying to create a new iCloud account, you might get a failure message: "Account limit reached." Apple imposes a limit of three iCloud account setups per device. Erasing the device does not reset the limit. You can still use an account that was created on another device, but you won't be able to create a new one. Contact iCloud Support for more information.

Having trouble trying to open links on my recieved mail. The only response I get when I click on the link is, "No associated application could be found".

Having trouble trying to open links on my recieved mail. The only response I get when I click on the link is, "No associated application could be found".
How can I correct this problem?

What type of file is it? What is the extension (the 3 letters after the . (DOT)) of the file?
Could be it is a Windows Exe file and simply will not run on a Mac. Which is good because anyone that would send you a excute (.EXE) file is up to no good. just my opinion.

I have Kelly Clarkson's "Breakaway" on my iTunes and on several playlists. When I play it on my computer it is the correct song, but when it plays on my iPhone it sounds like Mariah Cary singing some other song?? I miss "Breakaway" Help!

I have Kelly Clarkson's "Breakaway" on my iTunes and on several playlists. When I play it via my computer it is the correct song .... but when I try to play in from my iPhone via the cloud it sounds like Mariah Cary singing some other song. I have tried removing the song from my lists and reinstalling in from my iTunes on the computer ... plays correctly on the computer, but not on my phone.
I miss "Breakaway" .... pleasde help. I think there is something wrong in the Cloud ...

I have Kelly Clarkson's "Breakaway" on my iTunes and on several playlists. When I play it via my computer it is the correct song .... but when I try to play in from my iPhone via the cloud it sounds like Mariah Cary singing some other song. I have tried removing the song from my lists and reinstalling in from my iTunes on the computer ... plays correctly on the computer, but not on my phone.
I miss "Breakaway" .... pleasde help. I think there is something wrong in the Cloud ...

Oracle 10gr2 Master/detail form running very slow when you navigate to the detail record.

Hi All, I have a master detail form, running in webserver, when I navigate to the detail block, the form start buffering and buttering for about 2 min. There is a trigger when-new-record instance that is firing when you navigate to a new record : The select part of this stament is taken a long time to execute. I modified this in toad and what used to take 25 seconds to run is taken less than a second now, but the slowness still persists in the form.
for rec in (select wrrh_col
                  wpbh_col_lvd,
                   wpbh_col_doc_no
      from wh_col,
           wkpl_col,
           wh_col
     where wrrh_col_no = :block.wreh_wrrh_col_no
       and wrrh_col_no = wreh_wrrh_col_no
         and wrrh_col_no = wpbh_col_no
       and wrrh_col_proj    = wpbh_col_proj
       and wrrh_proj_no     = wpbh_proj_no) loop
   if fun_name(rec.wpbh_col_lvd) = 'Y' then
    do something,
   end if;
end loop;
The select staement that used to run for 23 seconds is running in less than one second, but the form is still running very slow when I navigate to the detail record.
Please advise.
Thanks.

Thanks Andrea for your prompt response, the problem is the select statement and like I stated, I tuned the select statement in toad and what normally takes 23 secs is taking less than 1 sec to run. If I comment out the call to the function, it is still slow. The select stament will returned null and it will still be slow. When I comment out the for loop, it run very fast. I dont know what else to do than tuned the select statement.

Why can I only create 4 forms when I have purchased the entire package at 100+ dollars?

Why can I only create 4 forms when I have purchased the entire package at 100+ dollars?

FormsCentral can be used from anywhere, but to purchase a subscription you need a credit card with the mailing address in one of the countries supported for purcahse:
http://forums.adobe.com/docs/DOC-1375
The partner can purchase if they have access to a card in one of those countries. Alternatively they do not need to purchase a subscription to edit forms that you've created, they do in order to create multiple forms of their own, but by your sharing forms with them at the "Co-author" level they have access to the editing. Here are the instructions to share a form:
http://forums.adobe.com/docs/DOC-2462
Thanks,
Josh

I get aq run time error when trying to load the latest version of iTunes. Help.

I get a run time error when attempting to install the latest version of iTunes & now cannot access iTunes. Can anyone help me?

Hi jalbany,
Thanks for using Apple Support Communities. This article has steps you can take for the error you're seeing:
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Cheers,
- Ari

Can I still get CS5 trial - I have limited internet access and just want software on my pc - I am only running vista so that looks to be the latest that will work for me

Can I still get CS5 trial - I have limited internet access and just want software on my pc - I am only running vista so that looks to be the latest that will work for me
If so what url do I go to as I have been round in circles and always come back to CC
Thanks

Downloadable installation files available:
Suites and Programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
Acrobat: XI, X | 9,8 | 9 standard
Premiere Elements: 13 |12 | 11, 10 | 9, 8, 7
Photoshop Elements: 13 |12 | 11, 10 | 9,8,7
Lightroom: 5.7.1| 5 | 4 | 3 | 2.7(win),2.7(mac)
Captivate: 8 | 7 | 6 | 5
Contribute: CS5 | CS4, CS3
Download and installation help for Adobe links
Download and installation help for Prodesigntools links are listed on most linked pages. They are critical; especially steps 1, 2 and 3. If you click a link that does not have those steps listed, open a second window using the Lightroom 3 link to see those 'Important Instructions'.window using the Lightroom 3 link to see those 'Important Instructions'.

My airport express never connects to the internet only flashes amber even when it's in the same room with the modem.

My airport express only flashes amber even when it's in the same room with the modem.
I want to set it up as a wi-Fi extender.

Your AirPort Express can only extend a wireless network provided by another Apple router if you want the network connection between them to be wireless.
What is the make & model of the wireless device that you are trying to extend with your Express?

I AM A CREATIVE CLOUD MEMBER FOR SOMETIME BUT NOW WHEN I LOGIN WITH THE CORRECT PASSWORD I STILL GET SIGNED OUT MESSAGE AND THEN WHEN TRIED THE SOLUTION GIVEN BY HELP THAT IS TO DELETE OPM.DB FILE OR SECOND SOLUTION INSTALL A FRESH CREATIVE CLOUD FOR DESK

I AM A CREATIVE CLOUD MEMBER FOR SOMETIME BUT NOW WHEN I LOGIN WITH THE CORRECT PASSWORD I STILL GET SIGNED OUT MESSAGE AND THEN WHEN TRIED THE SOLUTION GIVEN BY HELP THAT IS TO DELETE OPM.DB FILE OR SECOND SOLUTION INSTALL A FRESH CREATIVE CLOUD FOR DESKTOP APP OR EVEN SOLUTION OF RUN OF IMSLIBREPLACER IM STIILL NOT ABLE TO LOGIN TO MY CREATIVE CLOUD FOR DEKTOP APP . PLEASE HELP ME AS I NEED TO GET IN AND EXPLORE MORE OF MY DOWNLOADED S/W
I HAVE TRIED ALL POSSIBLE SOLUTION BUT AM AMAZED HOW THIS IS HAPPENING TO ME.
PLEASE PLEASE HELP ME .Creative Cloud Connection

Hi Alfred,
I would like to know the exact error message when you sign in, in the meanwhile please try the following steps assuming its Windows, let me know if its a MAC:
1) Go to Start button>> Control panel>> Uninstall a program.
2) Check if you see Browser safeguard there, if yes then uninstall it.
3) Open Internet explorer>> Tools>> Internet options>> Connections>> Lan Settings>> and it should be like this.
-Ankit

My mac book air is stuck on the log in page. When I type in the correct password, nothing happens. How can I get into my laptop??

I Have the latest iOS installment I believe. I don't know what is causing the problem as it was working perfectly last night! When I type in an incorrect password, the laptop recognizes that it is incorrect and denies me access. But when I type in the correct password nothing happens. I've turned the computer on and off and tried connecting to power also.

Really?
How about: MacBook Air
or: OS X Mavericks

Only run Group Policy when computer is on the correct IP range

Similar Messages

Maybe you are looking for