Optical Drive drawer Won't Open.

All of a sudden my optical drive drawer won't open when I press the top right open key on my key board.
Does anyone have any ideas what the problem may be?
Thanks for your help!
Steve

This, when run in the Terminal app, should eject the disk:
*drutil eject -drive internal*
Alternatively, restart holding down the mouse button. Finally, create a new admin user account, log into it, and see if the eject key works there.

Similar Messages

  • Bottom Optical Drawer Won't Open

    I have just installed a Blu-Ray drive into the bottom optical drive bay of my Mac Pro. It is a Matshita SD-5582, purchased from Other World Computing. The drive is recognized by system profiler, and an eject menu appeared in the menu bar all by itself. However, I can't get the drawer to open. I did remove the bezel from the drive before installing. A get a "thunk" noise when I try to eject using option-F12. It sounds like the drawer is trying to open, but the door on the Mac Pro case will not.
    One thing: when I removed the bezel, a tiny part of the door broke off, no more than 1/16 of an inch. Could that be the problem? And what's the best way to remove a bezel, since the drawer won't open without a power source?

    Optical drives do need mechanics to open the drawer. so it maight truly be a fault (which DO happen) with your new drive. I assume you have tried the paperclip thing (un"wind" a paper clip and insert in the "emergency "opening" hole (every optical drive has one, in case a disc gets stuck). this is not the easiest of things to do. but you need to (VERY well controlled) insert a straight pin (fitting the hole - paperclips have about the right size). You need to insert it fairly straight, and ensure, it does not "slip off" once inserted inside the drive.
    There should be an initial "resistance", followed by ability to push clip further into the hole, during which process the tray will emerge out of the drive.
    Sometimes, it might be wedged shut so that the motor is unable to open the tray normally. Saying that, as your drive is new, I'd get it exchanged. Good luck

  • Cd drawer won't open

    I am giving away my iMac tomorrow. This afternoon I used the OS X Install disk to start the computer and erased the volume. So far, so good. Unfortunately, I then ejected the disk before re-installing the operating system. Now the computer starts up, chimes, and displays a file icon with a flashing question mark, but the cd drawer won't open, so I am unable to reinstall the operating system. What can I do?

    Press the eject key on the keyboard, or the mouse button, or start up with the Option, Command, O, and F keys held down followed by entering 'eject cd' and then 'mac-boot' without the quote marks in either.
    (38513)

  • Hard Drive icon won't open and menu bar flashes off and on

    All of a sudden, in the middle of the day, my eMac went haywire. I can launch apps and docs are one the desktop. But I cannot open the Hard Drive icon. If I double-click on it (or used Command-O from keyboard), the icon won't open. And when I attempt to open it, the Finder Menu Bar begins flashing off and on (vanishing, reappearing, vanishing) across the top of the screen. I haver rebooted, run disk utility to repair permissions, even booted from TechTools to run its diagnostics. But still no access to the Hard Drive icon. I logged out and logged in as a TEST user, and same thing happens even when logged in that way. Literally, this happened in an instant. One minute the eMac was fine, then this started. Anyone else seen this? -- david

    If the problem exists in both your regular account and your Test account odds are that it is at the system level. You can try a Safe boot (hold down the shift key at startup) to see if there is a third party startup item or one of the optional Apple functions that is causing the problem. You could also boot from the installer disk and use the Disk Utility->Repair Disk function. If you have a utility such as Tiger Cache Cleaner which will do a deep cache clean you can also try that.
    Francine
    Schwieder

  • Optical disk trays won't open

    Greetings!
    I have a problem with my internal DVD drive's trays: they are stuck. When I press the “Eject” button (or “Option-Eject” for the second tray), I hear the drive trying to open the tray (the motor is forcing to push) and it stops around 10 seconds later (the usual abort when it can't open). Both drives are stuck.
    Last month, I've opened my Mac Pro and took out the drives. I've unscrewed them and managed to find the issue (using an IDE kit, I powered one of them and tried to see where the problem lied). I was unsure I found the problem, but it worked. However, one week later, one was stuck again, and again two days later, the other too.
    So, I want a definitive fix. I can't manage to open my computer each week to make my drives working only for one week and repeat this. I'm wondering if someone has or had the same issue?

    I realize this is an old post but it is the closest I have found discussing the Mac Pro optical drive problem. There are other posts about iMacs and software problems, but this deals with the MP mechanical problem. I have an early 2008 Mac Pro with the original SuperDrive and a SuperDrive from my old G3. Both work fine if I get a disk in them. I went through the whole routine. Three or four tries with the eject key used to work then nothing. Drive doors not working? Something broken inside? No. THE SOLUTION - The little rubber belt on the plastic pulleys that you can see if the tray is out needs to be cleaned/rejuvenated. However you get to it, clean it with some pure alcohol or other such solvent. I used automotive belt dressing. I pulled the drives out and opened the cases. Not too hard to do. I tried a little petroleum jelly on the rails of one and some spray wax on the other. This can be done without opening the case. I'm not sure if any lubrication was really needed. THE PROBLEM - There is a metal and plastic disk built into the top case of the drive centered over the spindle. With the tray closed, the spindle and drive mechanism are up in the "play position. Without a disk inserted, the MAGNET built into the top of the spindle makes direct contact with the disk in the top case. The rubber belt looses grip over time and can't break the magnetic bond anymore. It needs to be rejuvenated (or replaced if you can find one). The drive has to drop the spindle to allow a disk to be inserted. When you try to open the drive, it senses the mechanism is stuck and it gives up. When a DVD is inserted, the spindle is up and it pulls the metal disk in the top case down on top of the DVD to hold it in place. The top metal disk spins along with the DVD. I haven't tried a band-aid fix of always leaving a disk in the drive since my drives are working fine after cleaning the belt. Having a disk always in the drive may allow enough space to weaken the bond between the magnet and the top metal disk and allow the mechanism to do its job. Hitting the enclosure with clenched fists was probably enough to break the magnetic bond but I hope the rest of the computer survived. As for replacing drives, as recommended elsewhere for this problem, I think you need to get one that is Apple compatable. Otherwise you cannot boot from it. I hope this helps at least one person. It drove me crazy for a long time pressing the eject key multiple times to get the tray to open until that finally stopped and I had to do something.

  • Problem opening my CD Drive drawer

    I am actually having two issues. The first one is that my iMAC will only get to a gray screen and it won't go any further than that. I want to use my DVD to boot and repair my computer but I can't open my CD drawer. What can I do to get this open?

    Here are two ways of opening the optical drive tray:
    1. Hold the mouse button down immediately after the start-up chime, or,
    2. - Switch on/reboot
    - After the startup chime, press and hold the keys <command/apple> <alt/option> <o> and <f> ( ⌥ ⌘ F O )
    - At the command line prompt, type: eject cd
    - Hit Return, the optical drive tray will then open.
    -Insert the Install Disc
    - Type: mac-boot
    - Hit return. 
    Open Disk Utility from the menu bar
    Run "Repair Disk" on Macintosh HD.
    Let us know how you get on.
    mrtotes
    Message was edited by: mrtotes

  • Opening Optical Drive Bay

    I'm trying to install a second DVD drive, but I'm having trouble opening the drive bay. I'm following the directions in the manual: latch is up, side panel removed, etc. But pulling the drive bay out halfway to reach the cables is impossible.
    It moves perhaps a quarter inch and then refused to budge. I don't want to use force, fearing that the optical drive drawer may be stuck on something, and pulling too hard might break it.
    Should it be this hard to pull out?

    Hi,
    Pulling the thing out for the first time was a hassle for me too, eventually I jiggled with it from side to side moving out some millimeters at a time until it was out.
    The Good news is that the whole thing is pretty robust so you can use reasonable force and after its out for the first time it looses a-bit and then slides in a more expectable way.
    Have Fun,
    Baryo.

  • How do I open my optical drive without a keyboard

    I'm running a Quicksilver Dual 800 G4, without monitor, keyboard, or mouse. I can access it using my MacBook Pro, and view it using Screen Sharing. I want to install software from a DVD onto the dual 800, but how do I open the drive to insert the DVD?
    I have another Quicksilver (Dual 867 MDD) which has two optical drives, and on the status bar amidst the airport signal indicator, bluetooth indicator, etc is an eject symbol, which allows me to choose the optical drive I want to open. I have a keyboard connected to this machine, but as the facility exists in OS X to provide that functionality, how can I hack OS X to provide this option in the dual 800 with only one drive?

    Thank you for replying. Malcolm (above) managed to provide the exact solution I was looking for at the same time as you were typing your reply, judging from the time.
    I'm accessing the QS from my MacBook Pro (OS X 10.5), using a wired/wireless connection - the QS is wired, the MBPro wireless. At the moment they are about twelve inches apart, and I do have a keyboard to plug into the QS, but I'm hoping to set it up as a headless unit to take time lapse photos (using an iSight) and a clever script available here: http://gawker.sourceforge.net/Gawker.html
    Once set up, I hope to access the QS remotely, as it will live in Birmingham, and I live in Bristol! So thinking as far ahead as possible, I wanted to set it up to be controlled as much as possible by me, even if my caretaker in Birmingham has to put a disc in the tray from time to time.
    Again, many thanks!
    kind regards
    Andrew McDermott

  • Drive On Mac Pro Won't Open For Firmware Restoration?

    Hi--
    My Mac Pro (early 2008 model, OS 10.6.8) has recently begun having problems that seem firmware-related. When put in "Sleep" mode overnight, it wakes up on its own after about two hours of sleep and remains awake.  Also, from time to time it will display the prompt window ("Do You Want To Shut Down?") for a hard (button) shutdown---without the button having been pressed. Resetting the SMC and the PRAM solves the problem for awhile, but it's becoming necessary to do that more and more frequently---at first, the problem occured about every six months, then weekly, until now I'm getting the shutdown prompt and have to reset the SMC almost every day.
    Internet searches of this and other forums have indicated that a possible solution is restoring the firmware.  I have made a Firmware Restoration CD but I cannot get the machine to recognize it. That is, when I press and hold the startup button I get the "three long-three short-three-long" beeps; according to Apple's FAQ on ths subject, the optical drive door should then open and allow me to insert the Firmware Restoration disk, but that doesn't happen--the computer just goes right on with the normal startup sequence.
    Please advise.

    all I can do is tell you what I've learned here-try either one of these-hold down the shift key on startup/hold down the mouse on startup/if not,  See if you can boot up in single user mode/reset NVRAM,(command option, o+F)on reboot . Failing that....pull down the optical drive door, and using a straightened extra study paperclip, find the small hole near the optical drive tray. Stick that paperclip in and the tray should open up just enough for you to grab it and put the cd in there. Maybe then, start up holding down the C key......
    just a guess though
    Good luck to you
    John B

  • Drive won't open

    The SuperDrive drawer won't open. I've tried all the suggestions from "help" including starting up with the mouse button held down. When I use the "eject' button there is a click in the audio. Any help will be appreciated.
    Jim Easton

    Thanks for all you advice, I still don't know how to "reboot' with open firmware as was suggested with. This is what I did:
    1. Tray will not open by any means
    2. Forced tray open and installed 10.4.3 CD
    3. Installed 10.4.3, tray opens normally
    4. Downloaded 10.4.9 and installed it
    5. Tray will not operate at all
    6. Reinstalled 10.4.3, tray operates normally
    7. Cannot install 10.4.8, 10.4.7, 10.4.6 or 10.4.5
    8. Installed 10.4.4 and all works.
    9. So I guess I'll have to intall each upgrade one at a time until I get to 10.4.8 and then I'll stop until someone fixes 10.4.9. VERY FRUSTRATING
    I would appreciate any help and comments.
    Jim

  • Optical Drive Accesses for No Apparent Reason

    I have a new HP Pavilion dv7 laptop with Windows 7 64-bit OS. My question concerns accesses to the optical drive for no apparent reason. While it seems reasonable that when booting up the system the firmware will check the optical drive to see if there is a startup CD in it I do not understand other apparent attempts to access the optical drive. For example, after bootup and running within Windows 7 I attempt to play a mp3 music file residing on the hard disk I can hear the optical drive being accessed. Specifically, I double click on a mp3 file on my hard disk but before the music player application pops up I hear several clicks and clacks as the computer checks the optical drive for a disk...I assume. Is there a setup file someone where this kind of activity is enabled? IMHO, the computer should not be attempting to check the optical dirve  when attempting to play a mp3 file on the HD.
    Another scenario I've noticed is during the logon process. Specifically, as the computer boots up there is a typical click-clack of the optical drive as the firmware checks to see if there is a startup CD in the drive. Next, Windows 7 in up and running but sitting on the user logon screen. When I type my password to log onto my account I hear more click-clack accesses to the optical drive. This may be a typical thing for Windows 7...I'm not sure as I'm new to Windows 7. However, the description I gave above concerning playing of mp3 music seems odd.
    The sound I hear is definitely not the hard disk.  It is the same sound that the optical drive makes if you open the drive and close it without inserting a disk.  That is, the laser tracking motor moving the laser pickup from the outer edge to the inner edge and back to check to see if a CD or DVD is sitting in the drive.  Playing an mp3 music file residing on the hard disk causes this to happen.  It only happens once when starting up the music player.

    Hi There,
    What is the media application you have in the computer? Such as Intervideo windvd. cyberlink  etc…
    Few applications keep checking the media even though these applications are not in use. Fixes for such applications are posted on respective support websites, you may want to check and update. or if you do not wish to use such applications you can try un-installing these applications and verify the functionality.
    Hope it helps.
    Thank you,
    Waseem – HP 2LS
    **Click the KUDOS star on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
    Regards,
    WW
    “I am an HP Employee“
    ***** Click the KUDOS star on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem***

  • Optical Drive tray wont stay closed

    My PowerMacG5's optical drive door is stuck open. It will close using any of the normal procedures, but then immediately opens again whether there is a disk in it or not. No matter what I try, the tray always immediately re-opens and stays open. Any help would be greatly appreciated.

    Take a close look at the drive when you try to close it and see if the disc tray is hitting something.
    This is normal behavior for a drive whose tray is blocked by something, so there may be something in the way.

  • Why won't my optical drive open unless there is a disc in it?

    I bought my eMac (1.25Ghz, USB 2.0, MacOS 10.5.8) from my school last Friday, and have been fixing little glitches, deleting old files, etc. I've finally gotten everything in almost perfect working order except the optical drive. The drive itself seems fine and reads CD's no problem. The only problem is that the drive won't open on it''s own, I have to use the little paperclip hole everytime I want to open it. However, once the disc is in, it will read and eject the disc normally, but once the drive is empty again, I have to use the paperclip to get it open. I don't know if it's a hardware or software malfunction. Help!?
    P.S. It also spits out DVD's. I thought it was supposed to be able to read them (it reads CD's just fine), but it just gives DVD's back.

    I took off the face plate inside the the tray to make sure there was a spot for a Airport Extreme card (there is, and I'll be getting one =D ), and I noticed an eject button on the disc drive itself (right hand side), upon pressing that, it opened up just fine, so we can assume the drive works fine, however, I also noticed a little green light on the left hand side that is not illuminated. Should it be? Does this help at all? It's strange that the eject button on the drive works, and then it reads the CD I put in it, and will eject it with the button on the keyboard, but once I took the disk out it became inert again. =S
    Also, when I put the disk in, I went to the about this Mac, and then to ATA and it showed this:
    Without a disk it shows this:
    I think I had originally been looking at Serial-ATA which just says:
    This system does not contain any Serial-ATA devices. If you have any Serial-ATA devices installed, please check that they are connected and powered on.
    I hope this helps.
    Message was edited by: Josh08x

  • Mac Pro optical drive won't open - it could be virtualbox!

    I use Virtualbox to check websites in IE and other windows browsers.
    To get the optical drive to work in windows, I had to allow VB to "take over" the optical drive when VB was running.
    So when my optical drive would not open this morning, and just before panic set in, I remembered that I had left VB running an hour ago, and was probably not letting me open my optical drive from Mac OS.
    As soon as I shut down VB, I had full control of my optical drive again.

    I'm having exactly the same trouble with my Pioneer BDR-208D (SATA).  I have swapped bays and swapped drives with the earlier BDR-207D, but the same symptoms occur with both, so I do not believe it's a problem with the drive itself. It is as if power stops to the optical drive buses.
    My machine is a mid-2010 model Mac Pro 2 x 2.4 Ghz quad core running OSX 10.7.5.
    Any luck with the energy saver solution? I'm going to give that a try right now.
    -- Bill

  • Optical drive won't open

    How can I manually open the optical drive on my Mac Pro? There is no paperclip hole that I can see. Thanks in advance.
    (I searched for this and found nothing. It's hard to believe it hasn't been asked.)

    Hmm, that's interesting. I'll have to try the "...eject" next time I have a burn session freeze on me. (You know, where it's supposed to be burning a DVD, but the burning application sits there and churns with the beach ball, but it's not really doing anything, and it never comes out of it.) Had to resort to rebooting in the past. Happens a few times per year, which isn't much considering how many I burn, but it's annoying when it happens.
    I was searching for this stuff because I used to use option-F12 (Logitech keyboard) to open the second drive, but it stopped working, possibly because of the latest Logitech software update I installed. I have the previous Logitech update if I need to revert, but the new version has some other nice features, so this workaround isn't bad. I always (literally, always) have a terminal window open anyway, so I just did a few quick aliases for my drive open/close/eject functions. I'd still rather have a quick single key-combo, but this isn't bad.
    It's tempting to write a little script-application that would figure out if it was open or closed and then do the opposite, but looks like the only drutil bit that might tell me that information is the "poll" option, and that keeps polling, so it doesn't self-terminate, so things get messy from a coding standpoint. It's probably not worth that much work to me.
    Thanks for the tip!

Maybe you are looking for