Oracleasm error

Hi everybody,
On Oracle Linux I have installed oracle 10.2.0 and I want to deploy asm. I installed css service and ASM instance which both run. Then to create a disk group I made a partition with fdisk and initialized it with os volume maneger, it is called /dev/sda12 and is unmounted. When I issue:
./oracleasm createdisk ASMSDK /dev/sda12
it returns this error:
Marking disk "/dev/sda12" as an ASM disk: Error opening manager: No such device
or address [FAILED]
What's up?

Here is the output of ls command for my partition. This time I have created it with fdisk.
[root@IT-LAB init.d]# ls -al /dev/sda12
brw-rw-rw- 1 root disk 8, 12 Apr 19 2007 /dev/sda12
The problem still exists. Nobody knows the reason?!

Similar Messages

ASMLib for Fedora 4

Hi,
Did anyone installed ASMLib on Fedora 4 linux. From what i read, is that Fedora is using kernel 2.6.11..... The drivers on OTN are for 2.6.9...
Regards,
Frank

Hi,
I tried your solution. (thanks by the way). But i don't get it working (I am linux newbie).
I downloaded it, extracted it. Then i run "./configure". That went well (at least, i didn get any errors).
Then i run "make". Here i got errors :
make -C include
make[1]: Entering directory `/tmp/install/oracleasm-2.0.1/include'
make -C linux
make[2]: Entering directory `/tmp/install/oracleasm-2.0.1/include/linux'
make[2]: Nothing to be done for `all'.
make[2]: Leaving directory `/tmp/install/oracleasm-2.0.1/include/linux'
make[1]: Leaving directory `/tmp/install/oracleasm-2.0.1/include'
make -C kernel
make[1]: Entering directory `/tmp/install/oracleasm-2.0.1/kernel'
make -C /lib/modules/2.6.11-1.1369_FC4/build M=/tmp/install/oracleasm-2.0.1/kern el modules
make[2]: Entering directory `/usr/src/kernels/2.6.11-1.1369_FC4-i686'
CC [M] /tmp/install/oracleasm-2.0.1/kernel/oracleasm.o
/tmp/install/oracleasm-2.0.1/kernel/oracleasm.c:290: error: unknown field memor y_backed specified in initializer
make[3]: *** [tmp/install/oracleasm-2.0.1/kernel/oracleasm.o] Error 1
make[2]: *** [_module_/tmp/install/oracleasm-2.0.1/kernel] Error 2
make[2]: Leaving directory `/usr/src/kernels/2.6.11-1.1369_FC4-i686'
make[1]: *** [build-oracleasm] Error 2
make[1]: Leaving directory `/tmp/install/oracleasm-2.0.1/kernel'
make: *** [kernel] Error 2
Got any tips or hints what to do ?
Frank

Error: "FATAL: Module oracleasm not found" in Red Hat 6

Hi all:
   OS.....: Red Hat 6.5 (64 bits)
   I am preparing to install an 12c RAC in a Red Hat 6.5. While configuring the ASMLib, i got the following error while executing "/usr/sbin/oracleasm init":
      May 2 18:23:20 oraprd01 modprobe: FATAL: Module oracleasm not found.
   I configure the Oracle YUM Repository and installed the "kmod-oracleasm" package. And in the link (Oracle ASMLib Downloads for Red Hat Enterprise Linux Server 6) i got the "oracleasmlib" and "oracleasm-support" packages, as you can see below:
      [root@oraprd01 binarios]# rpm -qa | grep -i oracleasm
      kmod-oracleasm-2.0.8-4.el6_6.x86_64
      oracleasm-support-2.1.8-1.el6.x86_64
      oracleasmlib-2.0.4-1.el6.x86_64
   My kernel is:
      Linux oraprd01 2.6.32-431.el6.x86_64 #1 SMP Sun Nov 10 22:19:54 EST 2013 x86_64 x86_64 x86_64 GNU/Linux
   My Red Hat version is:
      [root@oraprd01 binarios]# cat /etc/redhat-release
      Red Hat Enterprise Linux Server release 6.5 (Santiago)
   Why am i getting the above error while trying to init the oracleasm module? What am i doing wrong?
   Thanks in advance.

Problem solved.
   I installed an older version of the kmod-oracleasm (kmod-oracleasm-2.0.6.rh1-3.el6_5.x86_64) downloaded from Red-Hat Customer Portal. Now the ASM module is loaded.

Error during ASMDISK Deletion in Oracleasm

Hi,
I need your help to drop ASMDISK from oracleasm device.
i have already drop this disk from existing Diskgroup from ASM and reblanced data in new disk in new storage.
Now i want to relese dropped ASMDISK to release old storage.
While Deleting the disk i am getting error ..
[root@TEST disksdisks]# /etc/init.d/oracleasm deletedisk TEST_DISK1
Removing ASM disk "TEST_DISK1": [FAILED]
How will i drop this TEST_DISK1 from asmdisk.
pls guide me drop this,
Thanks
AMit Tripathi
Edited by: Amit Shanker Tripathi on Aug 30, 2011 12:59 AM

Hi,
Put here the log /var/log/oracleasm
Please format the log.
When you post log, or any formatted text, on this site, type these 6 characters:
(small letters only, inside curly brackets) before and after sections of formatted text, to preserve spacing.
Levi Pereira

Oracleasm Createdisk error

Hello ,
I have just been trying to label oracle disk.
here is the error I get .
[db]# oracleasm createdisk DNAT01 /dev/sddc1
Unable to open device "/dev/sddc": Device or resource busy
I have already tried the solutions that were listed for this problem, but no success.
SELINUX is already disabled.
here is some additional info ...
[db]# oracleasm querydisk /dev/sddc1
Device "/dev/sddc1" is not marked as an ASM disk
[db]# oracleasm status
Checking if ASM is loaded: yes
Checking if /dev/oracleasm is mounted: yes
[db]# oracleasm configure
ORACLEASM_ENABLED=true
ORACLEASM_UID=oracle
ORACLEASM_GID=dba
ORACLEASM_SCANBOOT=true
ORACLEASM_SCANORDER=""
ORACLEASM_SCANEXCLUDE=""
Can someone help he find the solution to this problem? . highly appreciate.
Linux version is 5.3 .. running oracle 11g R2
Thanks
Saad
Edited by: Saad on Sep 18, 2011 12:45 AM

This is the metalink note, 1303976.1, I was talking about. This is another way to prove that device is busy, which we have already proved that device is busy (means used by one thing or another). Once you get mkfs working then creatdisk should work with no errors.
You can double, check that LVM, mount, RAID, MP, or similar thing is not already accessing the disk in question. For MP, you can shutdown another node, pull the cable from 2nd HBA/port and try it again. Due to limited access to your environment and due to lack of any logs, I think the options are just hit and trial and find out what is using that device. There are specific steps to implement mp, and please make sure no other VM or RAID is causing this issue.
Thanks,
Rohit Chandok
http://www.rohitchandok.com

Oracleasm lib failed to load with "Invalid module format" error

Hi,
I'm tring to install the oracleasm lib onto our hardened Redhat EL5 server
I've download the oracleasm rpm from this page http://www.oracle.com/technology/software/tech/linux/asmlib/rhel5.html.
We're using Redhat 5 U 2
[root@PG673 modules]# uname -rm
2.6.18-92.el5 x86_64
[root@PG673 modules]#
The package I downloaded is an exact match with our kernel version
[root@PG673 modules]# rpm -qa | grep asm
oracleasm-2.6.18-92.el5-2.0.5-1.el5
oracleasm-support-2.1.3-1.el5
oracleasm-support-2.1.3-1.el5
oracleasm-2.6.18-92.el5-2.0.5-1.el5
oracleasmlib-2.0.4-1.el5
oracleasmlib-2.0.4-1.el5
[root@PG673 modules]#
RPM installation went well, but when we run the /etc/init.d/oracleasm configure command, we hit the following error
[root@PG673 other]# /etc/init.d/oracleasm configure
/etc/init.d/oracleasm: line 207: /usr/sbin/oracleasm: cannot execute binary file
Later we found out that the oracleasm module haven't been loaded, so we try to load it manually, but we hit the "Invalid module format" error.
[root@PG673 modules]# modprobe -l | grep asm
/lib/modules/2.6.18-92.el5/kernel/drivers/addon/oracleasm/oracleasm.ko
[root@PG673 modules]# modprobe oracleasm
FATAL: Error inserting oracleasm (/lib/modules/2.6.18-92.el5/kernel/drivers/addon/oracleasm/oracleasm.ko): Invalid module format
[root@PG673 modules]#
As I know this error could happen if the driver version is not match with the system kernel version.
The problem is we're already using an exact match version of driver with our system, I can't think of what to do next in order to proceed the installation.
Really appreciate if someone could point me a direction.
Thanks
Mike

Hi Mike,
something looks a bit strange for me. On my OEL 5.4 x64 system i have just the following 3 packages:
$ rpm -qa | grep asm
oracleasm-2.6.18-164.el5-2.0.5-1.el5
oracleasm-support-2.1.3-1.el5
oracleasmlib-2.0.4-1.el5 Your packages should be I think the following:
http://oss.oracle.com/projects/oracleasm-support/dist/files/RPMS/rhel5/amd64/2.1.3/oracleasm-support-2.1.3-1.el5.x86_64.rpm
http://otn.oracle.com/software/tech/linux/asmlib/files/RPMS/rhel5/amd64/2.0.4/oracleasmlib-2.0.4-1.el5.x86_64.rpm
http://oss.oracle.com/projects/oracleasm/dist/files/RPMS/rhel5/amd64/2.0.5/2.6.18-92.el5/oracleasm-2.6.18-92.el5-2.0.5-1.el5.x86_64.rpm
Uninstall all asm packages and retry with just those three.
Good luck!
Cheers,
David
OCP 9i / 10g
http://www.oratoolkit.ch/knowledge/howto/installation/otn.php

Error while checking the status of Oracle Cluster ware

Hi
I was trying to install the database using dbca after setting up the grid and database software on LINUX x86-64 RHEL 5.7 machine. The database software version is 11.2.0.3. It throwing the error regarding the connectivity of clusterware. So I checked the status of clusterware.
-bash-3.2$ ./crsctl stat res -t
CRS-4535: Cannot communicate with Cluster Ready Services
CRS-4000: Command Status failed, or completed with errors.
-bash-3.2$
But when I ran below one:
-bash-3.2$ ./crsctl stat res -t -init
NAME TARGET STATE SERVER STATE_DETAILS
Cluster Resources
ora.asm
1 ONLINE ONLINE sfv9699 Started
ora.cluster_interconnect.haip
1 ONLINE ONLINE sfv9699
ora.crf
1 ONLINE ONLINE sfv9699
ora.crsd
1 ONLINE OFFLINE
ora.cssd
1 ONLINE ONLINE sfv9699
ora.cssdmonitor
1 ONLINE ONLINE sfv9699
ora.ctssd
1 ONLINE ONLINE sfv9699 OBSERVER
ora.diskmon
1 OFFLINE OFFLINE
ora.drivers.acfs
1 ONLINE ONLINE sfv9699
ora.evmd
1 ONLINE INTERMEDIATE sfv9699
ora.gipcd
1 ONLINE ONLINE sfv9699
ora.gpnpd
1 ONLINE ONLINE sfv9699
ora.mdnsd
1 ONLINE ONLINE sfv9699
So i saw that the crsd having some issue. I checked the alert log and crsd log. Below are the output.
Alert <server_name>.log
2012-10-20 15:37:51.408
[ohasd(3694)]CRS-2765:Resource 'ora.crsd' has failed on server 'sfv9699'.
2012-10-20 15:37:52.968
[crsd(5188)]CRS-1013:The OCR location in an ASM disk group is inaccessible. Details in /oracle2/app/11.2.0/grid/log/sfv9699/crsd/crsd.log.
2012-10-20 15:37:52.984
[crsd(5188)]CRS-0804:Cluster Ready Service aborted due to Oracle Cluster Registry error [PROC-26: Error while accessing the physical storage
ORA-27140: attach to post/wait facility failed
ORA-27300: OS system dependent operation:invalid_egid failed with status: 1
ORA-27301: OS failure message: Operation not permitted
ORA-27302: failure occurred at: skgpwinit6
ORA-27303: additional information: startup egid = 1000 (oinstall), current egid = 10002 (dba)
]. Details at (:CRSD00111:) in /oracle2/app/11.2.0/grid/log/sfv9699/crsd/crsd.log.
2012-10-20 15:37:53.471
[ohasd(3694)]CRS-2765:Resource 'ora.crsd' has failed on server 'sfv9699'.
2012-10-20 15:37:53.472
[ohasd(3694)]CRS-2771:Maximum restart attempts reached for resource 'ora.crsd'; will not restart.
CRSD.log
2012-10-20 15:37:52.456: [ CRSMAIN][3563381328] Checking the OCR device
2012-10-20 15:37:52.457: [ CRSMAIN][3563381328] Sync-up with OCR
2012-10-20 15:37:52.457: [ CRSMAIN][3563381328] Connecting to the CSS Daemon
2012-10-20 15:37:52.457: [ CRSMAIN][3563381328] Getting local node number
2012-10-20 15:37:52.459: [ CRSMAIN][3563381328] Initializing OCR
[   CLWAL][3563381328]clsw_Initialize: OLR initlevel [70000]
2012-10-20 15:37:52.897: [ OCRASM][3563381328]proprasmo: Error in open/create file in dg [DATA]
[ OCRASM][3563381328]SLOS : SLOS: cat=7, opn=kgfoAl06, dep=27140, loc=kgfokge
2012-10-20 15:37:52.898: [ OCRASM][3563381328]ASM Error Stack : ORA-27140: attach to post/wait facility failed
ORA-27300: OS system dependent operation:invalid_egid failed with status: 1
ORA-27301: OS failure message: Operation not permitted
ORA-27302: failure occurred at: skgpwinit6
ORA-27303: additional information: startup egid = 1000 (oinstall), current egid = 10002 (dba)
2012-10-20 15:37:52.967: [ OCRASM][3563381328]proprasmo: kgfoCheckMount returned [7]
2012-10-20 15:37:52.967: [ OCRASM][3563381328]proprasmo: The ASM instance is down
2012-10-20 15:37:52.968: [ OCRRAW][3563381328]proprioo: Failed to open [+DATA]. Returned proprasmo() with [26]. Marking location as UNAVAILABLE.
2012-10-20 15:37:52.968: [ OCRRAW][3563381328]proprioo: No OCR/OLR devices are usable
2012-10-20 15:37:52.968: [ OCRASM][3563381328]proprasmcl: asmhandle is NULL
2012-10-20 15:37:52.969: [    GIPC][3563381328] gipcCheckInitialization: possible incompatible non-threaded init from [prom.c : 690], original from [clsss.c : 5326]
2012-10-20 15:37:52.975: [ default][3563381328]clsvactversion:4: Retrieving Active Version from local storage.
2012-10-20 15:37:52.978: [ CSSCLNT][3563381328]clssgsgrppubdata: group (ocr_SFV9699-cluster) not found
2012-10-20 15:37:52.978: [ OCRRAW][3563381328]proprio_repairconf: Failed to retrieve the group public data. CSS ret code [20]
2012-10-20 15:37:52.981: [ OCRRAW][3563381328]proprioo: Failed to auto repair the OCR configuration.
2012-10-20 15:37:52.981: [ OCRRAW][3563381328]proprinit: Could not open raw device
2012-10-20 15:37:52.981: [ OCRASM][3563381328]proprasmcl: asmhandle is NULL
2012-10-20 15:37:52.983: [ OCRAPI][3563381328]a_init:16!: Backend init unsuccessful : [26]
2012-10-20 15:37:52.984: [ CRSOCR][3563381328] OCR context init failure. Error: PROC-26: Error while accessing the physical storage
ORA-27140: attach to post/wait facility failed
ORA-27300: OS system dependent operation:invalid_egid failed with status: 1
ORA-27301: OS failure message: Operation not permitted
ORA-27302: failure occurred at: skgpwinit6
ORA-27303: additional information: startup egid = 1000 (oinstall), current egid = 10002 (dba)
2012-10-20 15:37:52.984: [ CRSMAIN][3563381328] Created alert : (:CRSD00111:) : Could not init OCR, error: PROC-26: Error while accessing the physical storage
ORA-27140: attach to post/wait facility failed
ORA-27300: OS system dependent operation:invalid_egid failed with status: 1
ORA-27301: OS failure message: Operation not permitted
ORA-27302: failure occurred at: skgpwinit6
ORA-27303: additional information: startup egid = 1000 (oinstall), current egid = 10002 (dba)
2012-10-20 15:37:52.984: [    CRSD][3563381328][PANIC] CRSD exiting: Could not init OCR, code: 26
2012-10-20 15:37:52.984: [    CRSD][3563381328] Done.
=======================
I see in the above log that saying ASM instance is down and failed to open +DATA .
But the asm instance up and running
SQL> select instance_name,status from v$instance;
INSTANCE_NAME STATUS
+ASM1            STARTED
And we havent created any disk named DATA before the installation. We have created only below two disks
SQL> select name,header_status from v$asm_disk;
NAME HEADER_STATUS
ASM_DATA MEMBER
FLASH_RECOVERY MEMBER
But I am seeing a diskgroup in the v$asm_diskgroup which we havent created.
SQL> select name,state from v$asm_diskgroup;
NAME STATE
DATA MOUNTED
Ya this is a second time installtion. In the first installtion we created the asmdisk as DATA. But later everything (RAW device ) was formatted and this new disks has been created and installtion again started
[root@SFV9699 bin]# oracleasm listdisks
ASM_DATA
FLASH_RECOVERY
Seems like its trying to read the old disk DATA.
we have done asmscanning too with oracleasm scan disks. but no use.
Where I can remove the old entry of DATA disk.
It would be a great if a quick response get.
Thanks
SHIYAS M

The permission looks fine. If it was permission issue then y it is trying to read the DATA disk which I havent created this time at all ( But created in the first installation).
2012-10-20 15:37:52.459: [ CRSMAIN][3563381328] Initializing OCR
[ CLWAL][3563381328]clsw_Initialize: OLR initlevel [70000]
2012-10-20 15:37:52.897: [ OCRASM][3563381328]proprasmo: *Error in open/create file in dg [DATA]*[ OCRASM][3563381328]SLOS : SLOS: cat=7, opn=kgfoAl06, dep=27140, loc=kgfokge
2012-10-20 15:37:52.898: [ OCRASM][3563381328]ASM Error Stack : ORA-27140: attach to post/wait facility failed
ORA-27300: OS system dependent operation:invalid_egid failed with status: 1
ORA-27301: OS failure message: Operation not permitted
ORA-27302: failure occurred at: skgpwinit6
ORA-27303: additional information: startup egid = 1000 (oinstall), current egid = 10002 (dba)
2012-10-20 15:37:52.967: [ OCRASM][3563381328]proprasmo: kgfoCheckMount returned [7]
2012-10-20 15:37:52.967: [ OCRASM][3563381328]proprasmo: The ASM instance is down
2012-10-20 15:37:52.968: [ OCRRAW][3563381328]proprioo: *Failed to open [+DATA].* Returned proprasmo() with [26]. Marking location as UNAVAILABLE.
2012-10-20 15:37:52.968: [ OCRRAW][3563381328]proprioo: No OCR/OLR devices are usable
2012-10-20 15:37:52.968: [ OCRASM][3563381328]proprasmcl: asmhandle is NULL
The only disks created are
[root@SFV9699 dev]# oracleasm listdisks
ASM_DATA
FLASH_RECOVERY
And these disks are showing part of that group also.. Not quite sure how this happened..
what abt dropping this group.. will anything work.

Error in invoking target 'irman ioracle' of makefile '/opt/oragrid/rdbms/lib/ins_rdbms.mk'

Hello all,
I am attempting to install Oracle12c GI on two virtual nodes (in Fusion VMware) and am getting the following error message (Both nodes are configured exactly the same):
INFO: Start output from spawned process:
INFO: ----------------------------------
INFO:
INFO:
INFO: - Linking recovery manager (rman)
INFO: rm -f /opt/oragrid/rdbms/lib/rman
INFO: /opt/oragrid/bin/orald -o /opt/oragrid/rdbms/lib/rman -m64 -z noexecstack -Wl,--disable-new-dtags -L/opt/oragrid/rdbms/lib/ -L/opt/oragrid/lib/ -L/opt/oragrid/lib/stubs/   /opt/oragrid/lib/s0main.o /opt/oragrid/rdbms/lib/sskrmed.o /opt/oragrid/rdbms/lib/skrmpt.o -ldbtools12 -lclient12 -lsql12 -lpls12 -lrt -lplp12 -lsnls12 -lunls12 -lnls12 -lslax12 -lpls12 -lrt -lplp12 /opt/oragrid/lib/libplc12.a -lclntsh -lclntshcore `cat /opt/oragrid/lib/ldflags`    -lncrypt12 -lnsgr12 -lnzjs12 -ln12 -lnl12 -lnro12 `cat
INFO: /opt/oragrid/lib/ldflags`    -lncrypt12 -lnsgr12 -lnzjs12 -ln12 -lnl12 -lnnz12 -lzt12 -lztkg12 -lztkg12 -lclient12 -lnnetd12 -lvsn12 -lcommon12 -lgeneric12 -lmm -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lxml12 -lcore12 -lunls12 -lsnls12 -lnls12 -lcore12 -lnls12 `cat /opt/oragrid/lib/ldflags`    -lncrypt12 -lnsgr12 -lnzjs12 -ln12 -lnl12 -lnro12 `cat /opt/oragrid/lib/ldflags`    -lncrypt12 -lnsgr12 -lnzjs12 -ln12 -lnl12 -lclient12 -lnnetd12 -lvsn12 -lcommon12 -lgeneric12   -lsn
INFO: ls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lxml12 -lcore12 -lunls12 -lsnls12 -lnls12 -lcore12 -lnls12 -lclient12 -lnnetd12 -lvsn12 -lcommon12 -lgeneric12 -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lxml12 -lcore12 -lunls12 -lsnls12 -lnls12 -lcore12 -lnls12   `cat /opt/oragrid/lib/sysliblist` -Wl,-rpath,/opt/oragrid/lib -lm    `cat /opt/oragrid/lib/sysliblist` -ldl -lm   -L/opt/oragrid/lib
INFO: test ! -f /opt/oragrid/bin/rman ||\
    mv -f /opt/oragrid/bin/rman /opt/oragrid/bin/rmanO
INFO: mv /opt/oragrid/rdbms/lib/rman /opt/oragrid/bin/rman
INFO: chmod 751 /opt/oragrid/bin/rman
INFO: chmod 755 /opt/oragrid/bin
INFO:
INFO: - Linking Oracle
INFO: rm -f /opt/oragrid/rdbms/lib/oracle
INFO: /opt/oragrid/bin/orald -o /opt/oragrid/rdbms/lib/oracle -m64 -z noexecstack -Wl,--disable-new-dtags -L/opt/oragrid/rdbms/lib/ -L/opt/oragrid/lib/ -L/opt/oragrid/lib/stubs/   -Wl,-E /opt/oragrid/rdbms/lib/opimai.o /opt/oragrid/rdbms/lib/ssoraed.o /opt/oragrid/rdbms/lib/ttcsoi.o -Wl,--whole-archive -lperfsrv12 -Wl,--no-whole-archive /opt/oragrid/lib/nautab.o /opt/oragrid/lib/naeet.o /opt/oragrid/lib/naect.o /opt/oragrid/lib/naedhs.o /opt/oragrid/rdbms/lib/config.o -lserver12 -lodm12 -lcell12 -lnnet12 -lskgx
INFO: p12 -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lxml12 -lcore12 -lunls12 -lsnls12 -lnls12 -lcore12 -lnls12 -lclient12 -lvsn12 -lcommon12 -lgeneric12 -lknlopt `if /usr/bin/ar tv /opt/oragrid/rdbms/lib/libknlopt.a | grep xsyeolap.o > /dev/null 2>&1 ; then echo "-loraolap12" ; fi` -lskjcx12 -lslax12 -lpls12 -lrt -lplp12 -lserver12 -lclient12 -lvsn12 -lcommon12 -lgeneric12 `if [ -f /opt/oragrid/lib/libavserver12.a ] ; then echo "-lavserver12" ; else echo "-lavstub12"; fi` `if [ -f
INFO: /opt/oragrid/lib/libavclient12.a ] ; then echo "-lavclient12" ; fi` -lknlopt -lslax12 -lpls12 -lrt -lplp12 -ljavavm12 -lserver12 -lwwg `cat /opt/oragrid/lib/ldflags`    -lncrypt12 -lnsgr12 -lnzjs12 -ln12 -lnl12 -lnro12 `cat /opt/oragrid/lib/ldflags`    -lncrypt12 -lnsgr12 -lnzjs12 -ln12 -lnl12 -lnnzst12 -lzt12 -lztkg12 -lmm -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lxml12 -lcore12 -lunls12 -lsnls12 -lnls12 -lcore12 -lnls12 -lztkg12 `cat /opt/oragrid/lib/ldflags`    -lncrypt12
INFO: -lnsgr12 -lnzjs12 -ln12 -lnl12 -lnro12 `cat /opt/oragrid/lib/ldflags`    -lncrypt12 -lnsgr12 -lnzjs12 -ln12 -lnl12 -lnnzst12 -lzt12 -lztkg12   -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lxml12 -lcore12 -lunls12 -lsnls12 -lnls12 -lcore12 -lnls12 `if /usr/bin/ar tv /opt/oragrid/rdbms/lib/libknlopt.a | grep "kxmnsd.o" > /dev/null 2>&1 ; then echo " " ; else echo "-lordsdo12"; fi` -L/opt/oragrid/ctx/lib/ -lctxc12 -lctx12 -lzx12 -lgx12 -lctx12 -lzx12 -lgx12 -lordimt12 -lclsra12 -ldbc
INFO: fg12 -lhasgen12 -lskgxn2 -lnnzst12 -lzt12 -lxml12 -locr12 -locrb12 -locrutl12 -lhasgen12 -lskgxn2 -lnnzst12 -lzt12 -lxml12 -lgeneric12 -loraz -llzopro -lorabz2 -lipp_z -lipp_bz2 -lippdcemerged -lippsemerged -lippdcmerged -lippsmerged -lippcore -lippcpemerged -lippcpmerged -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lxml12 -lcore12 -lunls12 -lsnls12 -lnls12 -lcore12 -lnls12 -lsnls12 -lunls12 -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lcore12 -lsnls12 -lnls12 -lxml12 -lcore12
INFO: -lunls12 -lsnls12 -lnls12 -lcore12 -lnls12 -lasmclnt12 -lcommon12 -lcore12 -laio -lons    `cat /opt/oragrid/lib/sysliblist` -Wl,-rpath,/opt/oragrid/lib -lm    `cat /opt/oragrid/lib/sysliblist` -ldl -lm   -L/opt/oragrid/lib
INFO: /
INFO: usr
INFO: /
INFO: bin
INFO: /
INFO: ld
INFO: :
INFO:
INFO: cannot
INFO:
INFO: find
INFO:
INFO: -
INFO: ljavavm12
INFO:
INFO: collect2:
INFO: ld returned 1 exit status
INFO:
INFO: make: *** [/opt/oragrid/rdbms/lib/oracle] Error 1
INFO: End output from spawned process.
INFO: ----------------------------------
INFO: Exception thrown from action: make
Exception Name: MakefileException
Exception String: Error in invoking target 'irman ioracle' of makefile '/opt/oragrid/rdbms/lib/ins_rdbms.mk'. See '/opt/oraInventory/logs/installActions2013-11-25_04-25-06PM.log' for details.
Exception Severity: 1
Below are my VM specs:
**************************************************************Installed RPM's*****************************************************************
cat /etc/redhat-release
Red Hat Enterprise Linux Server release 6.4 (Santiago)
rpm -qa gcc
gcc-4.4.7-3.el6.x86_64
rpm -qa make
make-3.81-20.el6.x86_64
rpm -qa|grep oracle
oracleasmlib-2.0.4-1.el6.x86_64
oracle-logos-60.0.14-1.0.1.el6.noarch
oracle-rdbms-server-12cR1-preinstall-1.0-8.el6.x86_64
kmod-oracleasm-2.0.6.rh1-2.el6.x86_64
oraclelinux-release-notes-6Server-9.x86_64
oraclelinux-release-6Server-4.0.4.x86_64
oracleasm-support-2.1.8-1.el6.x86_64
***************************************************************JAVA***************************************************************************
java version "1.7.0_45"
Java(TM) SE Runtime Environment (build 1.7.0_45-b18)
Java HotSpot(TM) 64-Bit Server VM (build 24.45-b08, mixed mode)
*************************************************************SYSCTL**************************************************************************
# Kernel sysctl configuration file for Red Hat Linux
# For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and
# sysctl.conf(5) for more details.
# Controls IP packet forwarding
net.ipv4.ip_forward = 0
# Controls source route verification
net.ipv4.conf.default.rp_filter = 1
# Do not accept source routing
net.ipv4.conf.default.accept_source_route = 0
# Controls the System Request debugging functionality of the kernel
kernel.sysrq = 0
# Controls whether core dumps will append the PID to the core filename.
# Useful for debugging multi-threaded applications.
kernel.core_uses_pid = 1
kernel.core_pattern=/var/adm/crash/cores/%e.sig%s
# Controls the use of TCP syncookies
net.ipv4.tcp_syncookies = 1
# Disable netfilter on bridges.
net.bridge.bridge-nf-call-ip6tables = 0
net.bridge.bridge-nf-call-iptables = 0
net.bridge.bridge-nf-call-arptables = 0
# Controls the default maxmimum size of a mesage queue
kernel.msgmnb = 65536
# Controls the maximum size of a message, in bytes
kernel.msgmax = 65536
# Controls the maximum shared segment size, in bytes
# Controls the maximum number of shared memory segments, in pages
kernel.shmall = 4294967296
# oracle-rdbms-server-12cR1-preinstall setting for fs.file-max is 6815744
fs.file-max = 6815744
# oracle-rdbms-server-12cR1-preinstall setting for kernel.sem is '250 32000 100 128'
kernel.sem = 250 32000 100 128
# oracle-rdbms-server-12cR1-preinstall setting for kernel.shmmni is 4096
kernel.shmmni = 4096
# oracle-rdbms-server-12cR1-preinstall setting for kernel.shmall is 1073741824 on x86_64
# oracle-rdbms-server-12cR1-preinstall setting for kernel.shmmax is 4398046511104 on x86_64
kernel.shmmax = 4398046511104
# oracle-rdbms-server-12cR1-preinstall setting for net.core.rmem_default is 262144
net.core.rmem_default = 262144
# oracle-rdbms-server-12cR1-preinstall setting for net.core.rmem_max is 4194304
net.core.rmem_max = 4194304
# oracle-rdbms-server-12cR1-preinstall setting for net.core.wmem_default is 262144
net.core.wmem_default = 262144
# oracle-rdbms-server-12cR1-preinstall setting for net.core.wmem_max is 1048576
net.core.wmem_max = 1048576
# oracle-rdbms-server-12cR1-preinstall setting for fs.aio-max-nr is 1048576
fs.aio-max-nr = 1048576
# oracle-rdbms-server-12cR1-preinstall setting for net.ipv4.ip_local_port_range is 9000 65500
net.ipv4.ip_local_port_range = 9000 65500
# The below entries were added and deal with an r_filtering issue oracle wants private interconnects set loose
net.ipv4.conf.eth4.rp_filter = 2
net.ipv4.conf.eth6.rp_filter = 2
net.ipv4.conf.eth1.rp_filter = 1
*************************************************************Filesystem************************************************************************
Filesystem            Size Used Avail Use% Mounted on
/dev/mapper/vg_oracle12c-lv_root
                      8.9G 3.5G 5.0G 42% /
tmpfs                 2.2G     0 2.2G   0% /dev/shm
/dev/sda1             485M 101M 359M 22% /boot
/dev/mapper/vg_oracle12c-lv_home
                      2.0G   70M 1.9G   4% /home
/dev/mapper/vg_oracle12c-lv_tmp
                      4.5G 541M 3.7G 13% /tmp
/dev/mapper/vg_oracle12c-lv_var
                      5.0G 956M 3.8G 20% /var
/dev/mapper/oracle_vg-oragrid
                       20G 5.0G   14G 27% /opt/oragrid
.host:/               466G 137G 330G 30% /mnt/hgfs
*******************************************************************CPU INFO*******************************************************************************
cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 70
model name : Intel(R) Core(TM) i7-4850HQ CPU @ 2.30GHz
stepping : 1
cpu MHz : 2294.967
cache size : 6144 KB
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts mmx fxsr sse sse2 ss syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts nopl xtopology tsc_reliable nonstop_tsc aperfmperf pni pclmulqdq ssse3 fma cx16 sse4_1 sse4_2 x2apic movbe popcnt aes xsave avx f16c rdrand hypervisor lahf_lm ida arat epb xsaveopt pln pts dts fsgsbase smep
bogomips : 4589.93
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management:
processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 70
model name : Intel(R) Core(TM) i7-4850HQ CPU @ 2.30GHz
stepping : 1
cpu MHz : 2294.967
cache size : 6144 KB
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts mmx fxsr sse sse2 ss syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts nopl xtopology tsc_reliable nonstop_tsc aperfmperf pni pclmulqdq ssse3 fma cx16 sse4_1 sse4_2 x2apic movbe popcnt aes xsave avx f16c rdrand hypervisor lahf_lm ida arat epb xsaveopt pln pts dts fsgsbase smep
bogomips : 4589.93
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management:
processor : 2
vendor_id : GenuineIntel
cpu family : 6
model : 70
model name : Intel(R) Core(TM) i7-4850HQ CPU @ 2.30GHz
stepping : 1
cpu MHz : 2294.967
cache size : 6144 KB
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts mmx fxsr sse sse2 ss syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts nopl xtopology tsc_reliable nonstop_tsc aperfmperf pni pclmulqdq ssse3 fma cx16 sse4_1 sse4_2 x2apic movbe popcnt aes xsave avx f16c rdrand hypervisor lahf_lm ida arat epb xsaveopt pln pts dts fsgsbase smep
bogomips : 4589.93
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management:
processor : 3
vendor_id : GenuineIntel
cpu family : 6
model : 70
model name : Intel(R) Core(TM) i7-4850HQ CPU @ 2.30GHz
stepping : 1
cpu MHz : 2294.967
cache size : 6144 KB
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts mmx fxsr sse sse2 ss syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts nopl xtopology tsc_reliable nonstop_tsc aperfmperf pni pclmulqdq ssse3 fma cx16 sse4_1 sse4_2 x2apic movbe popcnt aes xsave avx f16c rdrand hypervisor lahf_lm ida arat epb xsaveopt pln pts dts fsgsbase smep
bogomips : 4589.93
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management:
*******************************************************************************Memory************************************************************************
free -m
             total       used       free     shared    buffers     cached
Mem:          4331       3972        359          0         30       3412
-/+ buffers/cache:        530       3801
Swap:        14323          0      14323
****************************************************************************Network***************************************************************************
Note eth0 is NAT and used for internet connectivity, eth1 is the public network (static and accessible to the hypervising machine running fusion ), eth4 and and eth6 are private, and eth3 is connected to an openfiler storage appliance (This is also a VM serving out ISCSI targets).
eth0      Link encap:Ethernet HWaddr 00:50:56:22:C6:91
          inet addr:192.168.90.140 Bcast:192.168.90.255 Mask:255.255.255.0
          inet6 addr: fe80::250:56ff:fe22:c691/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:227 errors:0 dropped:0 overruns:0 frame:0
          TX packets:225 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:24414 (23.8 KiB) TX bytes:18545 (18.1 KiB)
eth1      Link encap:Ethernet HWaddr 00:50:56:3A:AE:95
          inet addr:192.168.3.2 Bcast:192.168.3.255 Mask:255.255.255.0
          inet6 addr: fe80::250:56ff:fe3a:ae95/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:482561 errors:0 dropped:0 overruns:0 frame:0
          TX packets:450616 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:483728272 (461.3 MiB) TX bytes:501489666 (478.2 MiB)
eth3      Link encap:Ethernet HWaddr 00:50:56:24:40:AB
          inet addr:192.168.5.2 Bcast:192.168.5.255 Mask:255.255.255.0
          inet6 addr: fe80::250:56ff:fe24:40ab/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:4944 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3817 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6186232 (5.8 MiB) TX bytes:346478 (338.3 KiB)
eth4      Link encap:Ethernet HWaddr 00:50:56:3F:77:AA
          inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
          inet6 addr: fe80::250:56ff:fe3f:77aa/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:1222 errors:0 dropped:0 overruns:0 frame:0
          TX packets:978 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:205198 (200.3 KiB) TX bytes:168464 (164.5 KiB)
eth6      Link encap:Ethernet HWaddr 00:50:56:22:72:E3
          inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0
          inet6 addr: fe80::250:56ff:fe22:72e3/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:354 errors:0 dropped:0 overruns:0 frame:0
          TX packets:116 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:54390 (53.1 KiB) TX bytes:17992 (17.5 KiB)
lo        Link encap:Local Loopback
          inet addr:127.0.0.1 Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING MTU:16436 Metric:1
          RX packets:194338 errors:0 dropped:0 overruns:0 frame:0
          TX packets:194338 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:920534042 (877.8 MiB) TX bytes:920534042 (877.8 MiB)
*****************************************************************************ORACLE ASM AND MULTIPATH INFO********************************************
/etc/init.d/oracleasm listdisks
VOTE1
VOTE2
VOTE3
vote3 (14f504e46494c45523434517a65422d4b6364682d57544f65) dm-8 OPNFILER,VIRTUAL-DISK
size=3.0G features='0' hwhandler='0' wp=rw
`-+- policy='round-robin 0' prio=1 status=active
`- 3:0:0:2 sdh 8:112 active ready running
vote2 (14f504e46494c45526e6c6a48324a2d6a4347462d7a465074) dm-6 OPNFILER,VIRTUAL-DISK
size=3.0G features='0' hwhandler='0' wp=rw
`-+- policy='round-robin 0' prio=1 status=active
`- 3:0:0:1 sdg 8:96 active ready running
vote1 (14f504e46494c45525763646753422d594262512d414a6275) dm-7 OPNFILER,VIRTUAL-DISK
size=3.0G features='0' hwhandler='0' wp=rw
`-+- policy='round-robin 0' prio=1 status=active
`- 3:0:0:0 sdf 8:80 active ready running
If any more information is necessary please request and I will provide, as you can see there is more than enough memory and disk space for the installation. The only exception being that I am using a different 'oraInventory', 'gridhome', and 'oraBase'. I have looked closely at the output and the problem seems to be a file called 'ljavavm12', I have highlighted the line in bold above in the log output. Any help with this would be greatly appreciated.
Regards,
Alex

Resolved my own issue,
for anyone else having the same problem, here is how it was resolved:
ljavavm12 is part of libjavavm12.a, for some reason this file was not copied into the $GRID_HOME, after doing so make went through fine.
'cp /opt/oragrid/javavm/jdk/jdk7/lib/libjavavm12.a /opt/oragrid/lib/'
Alex,

File verification errors applying GI PSU 11.2.0.3.1 for acfs on linux

(Hi guys. i'm filing an SR at the same time, but I find I get more helpful responses from the forums, and we end up sharing technical knowledge in a more effective way.)
Platform: Proof of concept Virtualbox VM running Oracle Linux 5u7
Installed Grid Infrastructure 11.2.0.3 straight (didn't start with 11.2.0.1 and upgraded out-of-place)
My Linux kernel was apparently not supporting
root@oel4::/root] uname -r
2.6.32-200.13.1.el5uek
root@oel4::/root] uname -a
Linux oel4 2.6.32-200.13.1.el5uek #1 SMP Wed Jul 27 21:02:33 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux
oracle@oel4 [+ASM] Mon Feb 13:/orafs1/app/grid/product/11.2.0.3/grid/bin
22:51:14] oracleasm configure
ORACLEASM_ENABLED=true
ORACLEASM_UID=oracle
ORACLEASM_GID=dba
ORACLEASM_SCANBOOT=true
ORACLEASM_SCANORDER=""
ORACLEASM_SCANEXCLUDE=""In the ASMCA utility, I do NOT see a valid tab for the ADVM drive or ACFS filesystem. I could ONLY create ASM diskgroups. In addition, when trying to check whether the ACFS / ADVM drivers are even installed, tI see they are NOT:
Error encountered:
oracle@oel4 [+ASM] Mon Feb 13:/orafs1/app/grid/product/11.2.0.3/grid/bin
23:05:08] ./acfsdriverstate installed
ACFS-9204: false
oracle@oel4 [+ASM] Mon Feb 13:/orafs1/app/grid/product/11.2.0.3/grid/bin> ./acfsdriverstate supported
ACFS-9459: ADVM/ACFS is not supported on this OS version: '2.6.32-200.13.1.el5uek'
ACFS-9201: Not Supported-- I have already checked the following articles:
+ACFS tools fail with ADVM/ACFS is not supported on [ID 1085146.1]+
+IS ACFS/ADVM SUPPORTED/CERTIFIED ON SOLARIS SPARC 64 PLATFORM? [ID 973387.1]+
+How to Verify that the ACFS Driver is installed and loaded [ID 1319263.1]+
- out of curiosity, would I be able to boot the GRUB-loader WITHOUT the linux UEK kernel, and instead boot with the
*2.6.18-274.el5 kernel*? I tried it and ACFS now worked under 11.2.0.3 (when loading via ./acfsroot install)I wasn't sure of the impact to other application, and I assume there ARE risks in doing this.
-- I had thought that as of *11.2.0.3*, ACFS WAS supported under the Linux UEK. In addition, the MOS note 1369107.1 that 11.2.0.3.1 patch set update 1 would provide support for ACFS on the UEK2.6.32-200
"Support for "2.6.32-200" kernels will start in the first GI PSU 11.2.0.3.1 (11.2.0.3 GIPSU #1), (RFI Bug:13241736 & Bug:12825835). "
To test that, I tried applying the 11.2.0.3.1 grid control PSU 1:
## get existing opatch config:
     /orafs1/app/grid/product/11.2.0/grid/OPatch/opatch lsinventory
          Oracle Home       : /orafs1/app/grid/product/11.2.0/grid
          Central Inventory : /orafs1/app/oraInventory
             from           : /orafs1/app/grid/product/11.2.0/grid/oraInst.loc
          OPatch version    : 11.2.0.1.9
          OUI version       : 11.2.0.3.0
          Log file location : /orafs1/app/grid/product/11.2.0/grid/cfgtoollogs/opatch/opatch2012-02-18_12-20-11PM.log
          Lsinventory Output file location : /orafs1/app/grid/product/11.2.0/grid/cfgtoollogs/opatch/lsinv/lsinventory2012-02-18_12-20-11PM.txt
          Installed Top-level Products (1):
          Oracle Grid Infrastructure                                           11.2.0.3.0
          There are 1 products installed in this Oracle Home.
          There are no Interim patches installed in this Oracle Home.
          OPatch succeeded.
## run conflict resolution checks:
$ORACLE_HOME/OPatch/opatch prereq CheckConflictAgainstOHWithDetail -phBaseDir 13343438 -oh /orafs1/app/grid/product/11.2.0/grid
     PREREQ session
     Oracle Home       : /orafs1/app/grid/product/11.2.0/grid
     Central Inventory : /orafs1/app/oraInventory
        from           : /orafs1/app/grid/product/11.2.0/grid/oraInst.loc
     OPatch version    : 11.2.0.1.9
     OUI version       : 11.2.0.3.0
     Log file location : /orafs1/app/grid/product/11.2.0/grid/cfgtoollogs/opatch/opatch2012-02-18_12-17-54PM.log
     Invoking prereq "checkconflictagainstohwithdetail"
     Prereq "checkConflictAgainstOHWithDetail" passed.
     OPatch succeeded.
$ORACLE_HOME/OPatch/opatch prereq CheckConflictAgainstOHWithDetail -phBaseDir 13348650 -oh /orafs1/app/grid/product/11.2.0/grid
     PREREQ session
     Oracle Home       : /orafs1/app/grid/product/11.2.0/grid
     Central Inventory : /orafs1/app/oraInventory
        from           : /orafs1/app/grid/product/11.2.0/grid/oraInst.loc
     OPatch version    : 11.2.0.1.9
     OUI version       : 11.2.0.3.0
     Log file location : /orafs1/app/grid/product/11.2.0/grid/cfgtoollogs/opatch/opatch2012-02-18_12-18-06PM.log
     Invoking prereq "checkconflictagainstohwithdetail"
     Prereq "checkConflictAgainstOHWithDetail" passed.
     OPatch succeeded.I had checked the MOS Oracle Database Patch Set Update 11.2.0.3.1 Known Issues [ID 1374706.1] article, which didn't mention any show stoppers related to me.
# copy patch to tmp dir instead and run from there
     su - oracle
     cd /tmp
     mkdir p13348650
     unzip /mnt/share/100g/downloads/oracle/gi_11.2.0.3.1_psu1/p13348650_112030_Linux-x86-64.zip -d p13348650
     cp -p /mnt/share/100g/downloads/oracle/gi_11.2.0.3.1_psu1/ocm.rsp .
     ls -l
          -rwxrwxrwx 1 root    michael       1069 Feb 16 16:55 ocm.rsp
          drwxr-xr-x 4 oracle oinstall      4096 Feb 18 08:30 p13348650
     su -
     . oraenv
          +ASM
     cd /tmp
     $ORACLE_HOME/OPatch/opatch auto p13348650 -oh $ORACLE_HOME -ocmrf ocm.rsp
          Executing /usr/bin/perl /orafs1/app/grid/product/11.2.0/grid/OPatch/crs/patch112.pl -patchdir . -patchn p13348650 -oh /orafs1/app/grid/product/11.2.0/grid -ocmrf ocm.rsp -paramfile /orafs1/app/grid/product/11.2.0/grid/crs/install/crsconfig_params
          opatch auto log file location is /orafs1/app/grid/product/11.2.0/grid/OPatch/crs/../../cfgtoollogs/opatchauto2012-02-18_08-31-32.log
          Detected Oracle Restart install
          Using configuration parameter file: /orafs1/app/grid/product/11.2.0/grid/crs/install/crsconfig_params
          Successfully unlock /orafs1/app/grid/product/11.2.0/grid
          patch ./p13348650/13348650 apply failed for home /orafs1/app/grid/product/11.2.0/grid
          ACFS-9459: ADVM/ACFS is not supported on this OS version: '2.6.32-200.13.1.el5uek'
          CRS-4123: Oracle High Availability Services has been started.
# it STILL does not support ACFS on my kernel! ngng.
capture log output:
     cat /orafs1/app/grid/product/11.2.0/grid/OPatch/crs/../../cfgtoollogs/opatchauto2012-02-18_08-31-32.log
           Is the local system ready for patching? [y|n]
           Y (auto-answered by -silent)
           User Responded with: Y
           Backing up files...
           Applying interim patch '13348650' to OH '/orafs1/app/grid/product/11.2.0/grid'
           Patching component oracle.crs, 11.2.0.3.0...
           Copying file to "/orafs1/app/grid/product/11.2.0/grid/crs/install/crsconfig_lib.pm"
           Copying file to "/orafs1/app/grid/product/11.2.0/grid/crs/install/crspatch.pm"
           Copying file to "/orafs1/app/grid/product/11.2.0/grid/crs/install/s_crsconfig_lib.pm"
           Patching component oracle.usm, 11.2.0.3.0...
           There are 2 copy files under ORACLE_HOME that are not patched.
           Files check failed: Some files under ORACLE_HOME are not patched. Please see log file for details.
           ApplySession failed in system modification phase... 'Verification of patch failed: Files are not updated completely.'
           Restoring "/orafs1/app/grid/product/11.2.0/grid" to the state prior to running NApply...
           Checking if OPatch needs to invoke 'make' to restore some binaries...
           OPatch was able to restore your system. Look at log file and timestamp of each file to make sure your system is in the state prior to applying the patch.
           NApply restored the home. Please check your ORACLE_HOME to make sure:
             - files are restored properly.
             - binaries are re-linked correctly.
           (use restore.[sh,bat] and make.txt (Unix only) as a reference. They are located under
           "/orafs1/app/grid/product/11.2.0/grid/.patch_storage/NApply/2012-02-18_08-33-44AM"
           UtilSession failed: ApplySession failed in system modification phase... 'Verification of patch failed: Files are not updated completely.'
           Log file location: /orafs1/app/grid/product/11.2.0/grid/cfgtoollogs/opatch/opatch2012-02-18_08-33-44AM.log
           OPatch failed with error code 73
          2012-02-18 08:39:08: patch ./p13348650/13348650 apply failed for home /orafs1/app/grid/product/11.2.0/grid
cat /orafs1/app/grid/product/11.2.0/grid/cfgtoollogs/opatch/opatch2012-02-18_08-33-44AM.log
     [Feb 18, 2012 8:37:49 AM]    verifying 921 copy files.
     [Feb 18, 2012 8:37:56 AM]    Failed file pair information (copy)::
     [Feb 18, 2012 8:37:56 AM]    Source file name is : /tmp/p13348650/13348650/files/bin/oraagent.bin, size is : 28054745
     [Feb 18, 2012 8:37:56 AM]    Destination file name is : /orafs1/app/grid/product/11.2.0/grid/bin/oraagent.bin, size is : 28054745
     [Feb 18, 2012 8:38:04 AM]    Failed file pair information (copy)::
     [Feb 18, 2012 8:38:04 AM]    Source file name is : /tmp/p13348650/13348650/files/install/usm/SLES10/x86_64/2.6.16.21-0.8/default/bin/oracleacfs.ko, size is : 19649565
     [Feb 18, 2012 8:38:04 AM]    Destination file name is : /orafs1/app/grid/product/11.2.0/grid/install/usm/SLES10/x86_64/2.6.16.21-0.8/default/bin/oracleacfs.ko, size is : 19649565
     [Feb 18, 2012 8:38:07 AM]    verifying 3 plugin actions.
     [Feb 18, 2012 8:38:07 AM]    There are 2 copy files under ORACLE_HOME that are not patched.
     [Feb 18, 2012 8:38:07 AM]    OUI-67124:Files check failed: Some files under ORACLE_HOME are not patched. Please see log file for details.
     [Feb 18, 2012 8:38:07 AM]    OUI-67124:ApplySession failed in system modification phase... 'Verification of patch failed: Files are not updated completely.'
     [Feb 18, 2012 8:38:07 AM]    Restoring "/orafs1/app/grid/product/11.2.0/grid" to the state prior to running NApply...
     [Feb 18, 2012 8:39:08 AM]    Checking if OPatch needs to invoke 'make' to restore some binaries...
     [Feb 18, 2012 8:39:08 AM]    OPatch was able to restore your system. Look at log file and timestamp of each file to make sure your system is in the state prior to applying the patch.
     [Feb 18, 2012 8:39:08 AM]    OUI-67124:
                                  NApply restored the home. Please check your ORACLE_HOME to make sure:
                                    - files are restored properly.
                                    - binaries are re-linked correctly.
                                  (use restore.[sh,bat] and make.txt (Unix only) as a reference. They are located under
                                  "/orafs1/app/grid/product/11.2.0/grid/.patch_storage/NApply/2012-02-18_08-33-44AM"
     [Feb 18, 2012 8:39:08 AM]    OUI-67073:UtilSession failed: ApplySession failed in system modification phase... 'Verification of patch failed: Files are not updated completely.'
     [Feb 18, 2012 8:39:08 AM]    --------------------------------------------------------------------------------
     [Feb 18, 2012 8:39:08 AM]    The following warnings have occurred during OPatch execution:
     [Feb 18, 2012 8:39:08 AM]    1) OUI-67124:Files check failed: Some files under ORACLE_HOME are not patched. Please see log file for details.
     [Feb 18, 2012 8:39:08 AM]    2) OUI-67124:ApplySession failed in system modification phase... 'Verification of patch failed: Files are not updated completely.'
     [Feb 18, 2012 8:39:08 AM]    3) OUI-67124:
                                  NApply restored the home. Please check your ORACLE_HOME to make sure:
                                    - files are restored properly.
                                    - binaries are re-linked correctly.
                                  (use restore.[sh,bat] and make.txt (Unix only) as a reference. They are located under
                                  "/orafs1/app/grid/product/11.2.0/grid/.patch_storage/NApply/2012-02-18_08-33-44AM"
     [Feb 18, 2012 8:39:08 AM]    --------------------------------------------------------------------------------There were errors with the file verification after the copy , for some reason. I don't know why it would have coughed on the two files oraagent.bin and oracleacfs.ko, but Oracle Support and google seaches didn't come up with anything. I plan to manually try an opatch apply instead of the oaptch auto, but while I do so, does anybody have clues for correctly applying this PSU?

To update this thread, I ended up speaking to Oracle Support on this. It turned out that one of the prerequisites in the README was the culprit:
2.1.4 Unzipping the PatchThe patch application requires explicit user actions to run 'opatch auto' command on each node of Oracle clusterware. So, it is recommended that you download and unzip the patch in a shared location to be able to access it from any node in the cluster and then as the Grid home owner execute the unzip command. To prevent installation failures, this location should be an empty directory.
Note:
Do not unzip the patch in the top level /tmp directory.
The unzipped patch location should have read permission for ORA_INSTALL group in order to patch Oracle homes owned by different owners. The ORA_INSTALL group is the primary group of the user who owns the GI home or the group owner of the Oracle central inventory.>
In my example, I had unzipped to /tmp. However, the resulting error message stack didn't really point that out.
When I double-checked the README and tried again from /home/oracle/patches/p13348650 instead, it worked. It doesn't leave me with a confident feeling, more just relief. On a related note (and the entire reason for me patching to 11.2.0.3.1), ACFS filesystems ARE supported now under Oracle 5 update 7 with the 2.6.32-200.13.1.el5uek kernel (you had to really dig through the matrix in 1369107.1). Had this not worked, I would had to fail back to the non-UEK kernel to achieve ACFS.

Error while checking the command ttcwadmin -status

Hi
Getting error while checking the status of timesten cluster agent
Any clue
[ttadmin@VFS1UUP02 bin]$ ttcwadmin -status
TimesTen Cluster status report as of Wed Jun 26 15:03:42 2013
(ttCWAdmin:) crsctl.c(715): TT48004: clsssinit failed with status = 3.
*** glibc detected *** /timesten/tt1122/TimesTen/tt1122/bin/ttCWAdminCmd: double free or corruption (out): 0x00007fffcc7c6b00 ***
======= Backtrace: =========
/lib64/libc.so.6[0x34b14760e6]
/lib64/libc.so.6[0x34b1478c13]
/timesten/tt1122/TimesTen/tt1122/lib/libttcrs.so(crsAgentCtl+0xa6e)[0x7f6f32b71316]
/timesten/tt1122/TimesTen/tt1122/bin/ttCWAdminCmd[0x4062be]
/timesten/tt1122/TimesTen/tt1122/bin/ttCWAdminCmd[0x402784]
/lib64/libc.so.6(__libc_start_main+0xfd)[0x34b141ecdd]
/timesten/tt1122/TimesTen/tt1122/bin/ttCWAdminCmd[0x4020ca]
======= Memory map: ========
00400000-0040c000 r-xp 00000000 fd:0f 263189                             /timesten/tt1122/TimesTen/tt1122/bin/ttCWAdminCmd
0050b000-0050e000 rw-p 0000b000 fd:0f 263189                             /timesten/tt1122/TimesTen/tt1122/bin/ttCWAdminCmd
0050e000-00510000 rw-p 00000000 00:00 0
00906000-009a4000 rw-p 00000000 00:00 0                                  [heap]
34b0c00000-34b0c20000 r-xp 00000000 fd:07 135526                         /lib64/ld-2.12.so
34b0e1f000-34b0e20000 r--p 0001f000 fd:07 135526                         /lib64/ld-2.12.so
34b0e20000-34b0e21000 rw-p 00020000 fd:07 135526                         /lib64/ld-2.12.so
34b0e21000-34b0e22000 rw-p 00000000 00:00 0
34b1000000-34b1002000 r-xp 00000000 fd:07 135534                         /lib64/libdl-2.12.so
34b1002000-34b1202000 ---p 00002000 fd:07 135534                         /lib64/libdl-2.12.so
34b1202000-34b1203000 r--p 00002000 fd:07 135534                         /lib64/libdl-2.12.so
34b1203000-34b1204000 rw-p 00003000 fd:07 135534                         /lib64/libdl-2.12.so
34b1400000-34b158a000 r-xp 00000000 fd:07 135527                         /lib64/libc-2.12.so
34b158a000-34b1789000 ---p 0018a000 fd:07 135527                         /lib64/libc-2.12.so
34b1789000-34b178d000 r--p 00189000 fd:07 135527                         /lib64/libc-2.12.so
34b178d000-34b178e000 rw-p 0018d000 fd:07 135527                         /lib64/libc-2.12.so
34b178e000-34b1793000 rw-p 00000000 00:00 0
34b1800000-34b1817000 r-xp 00000000 fd:07 135532                         /lib64/libpthread-2.12.so
34b1817000-34b1a17000 ---p 00017000 fd:07 135532                         /lib64/libpthread-2.12.so
34b1a17000-34b1a18000 r--p 00017000 fd:07 135532                         /lib64/libpthread-2.12.so
34b1a18000-34b1a19000 rw-p 00018000 fd:07 135532                         /lib64/libpthread-2.12.so
34b1a19000-34b1a1d000 rw-p 00000000 00:00 0
34b2000000-34b2083000 r-xp 00000000 fd:07 131322                         /lib64/libm-2.12.so
34b2083000-34b2282000 ---p 00083000 fd:07 131322                         /lib64/libm-2.12.so
34b2282000-34b2283000 r--p 00082000 fd:07 131322                         /lib64/libm-2.12.so
34b2283000-34b2284000 rw-p 00083000 fd:07 131322                         /lib64/libm-2.12.so
34b4000000-34b4016000 r-xp 00000000 fd:07 135243                         /lib64/libnsl-2.12.so
34b4016000-34b4215000 ---p 00016000 fd:07 135243                         /lib64/libnsl-2.12.so
34b4215000-34b4216000 r--p 00015000 fd:07 135243                         /lib64/libnsl-2.12.so
34b4216000-34b4217000 rw-p 00016000 fd:07 135243                         /lib64/libnsl-2.12.so
34b4217000-34b4219000 rw-p 00000000 00:00 0
34b4800000-34b4816000 r-xp 00000000 fd:07 135531                         /lib64/libgcc_s-4.4.7-20120601.so.1
34b4816000-34b4a15000 ---p 00016000 fd:07 135531                         /lib64/libgcc_s-4.4.7-20120601.so.1
34b4a15000-34b4a16000 rw-p 00015000 fd:07 135531                         /lib64/libgcc_s-4.4.7-20120601.so.1
7f6f2d4f0000-7f6f2d513000 rw-p 00000000 00:00 0
7f6f2d513000-7f6f2d515000 r-xp 00000000 fd:10 2104758                    /u01/app/11.2.0/grid/lib/libskgxn2.so
7f6f2d515000-7f6f2d614000 ---p 00002000 fd:10 2104758                    /u01/app/11.2.0/grid/lib/libskgxn2.so
7f6f2d614000-7f6f2d615000 rw-p 00001000 fd:10 2104758                    /u01/app/11.2.0/grid/lib/libskgxn2.so
7f6f2d615000-7f6f2dcdf000 r-xp 00000000 fd:10 2104742                    /u01/app/11.2.0/grid/lib/libhasgen11.so
7f6f2dcdf000-7f6f2ddde000 ---p 006ca000 fd:10 2104742                    /u01/app/11.2.0/grid/lib/libhasgen11.so
7f6f2ddde000-7f6f2de00000 rw-p 006c9000 fd:10 2104742                    /u01/app/11.2.0/grid/lib/libhasgen11.so
7f6f2de00000-7f6f2de06000 rw-p 00000000 00:00 0
7f6f2de06000-7f6f2dead000 r-xp 00000000 fd:10 2104735                    /u01/app/11.2.0/grid/lib/libocr11.so
7f6f2dead000-7f6f2dfad000 ---p 000a7000 fd:10 2104735                    /u01/app/11.2.0/grid/lib/libocr11.so
7f6f2dfad000-7f6f2dfb0000 rw-p 000a7000 fd:10 2104735                    /u01/app/11.2.0/grid/lib/libocr11.so
7f6f2dfb0000-7f6f2e053000 r-xp 00000000 fd:10 2104718                    /u01/app/11.2.0/grid/lib/libocrb11.so
7f6f2e053000-7f6f2e152000 ---p 000a3000 fd:10 2104718                    /u01/app/11.2.0/grid/lib/libocrb11.so
7f6f2e152000-7f6f2e154000 rw-p 000a2000 fd:10 2104718                    /u01/app/11.2.0/grid/lib/libocrb11.so
7f6f2e154000-7f6f2e15f000 r-xp 00000000 fd:10 2104764                    /u01/app/11.2.0/grid/lib/libocrutl11.so
7f6f2e15f000-7f6f2e25f000 ---p 0000b000 fd:10 2104764                    /u01/app/11.2.0/grid/lib/libocrutl11.so
7f6f2e25f000-7f6f2e260000 rw-p 0000b000 fd:10 2104764                    /u01/app/11.2.0/grid/lib/libocrutl11.so
7f6f2e260000-7f6f2e261000 r-xp 00000000 fd:07 132252                     /lib64/libaio.so.1.0.1
7f6f2e261000-7f6f2e460000 ---p 00001000 fd:07 132252                     /lib64/libaio.so.1.0.1
7f6f2e460000-7f6f2e461000 rw-p 00000000 fd:07 132252                     /lib64/libaio.so.1.0.1
7f6f2e46c000-7f6f30a3e000 r-xp 00000000 fd:10 2104660                    /u01/app/11.2.0/grid/lib/libclntsh.so.11.1
7f6f30a3e000-7f6f30c3d000 ---p 025d2000 fd:10 2104660                    /u01/app/11.2.0/grid/lib/libclntsh.so.11.1
7f6f30c3d000-7f6f30dd3000 rw-p 025d1000 fd:10 2104660                    /u01/app/11.2.0/grid/lib/libclntsh.so.11.1
7f6f30dd3000-7f6f30df8000 rw-p 00000000 00:00 0
7f6f30df8000-7f6f31081000 r-xp 00000000 fd:10 2104768                    /u01/app/11.2.0/grid/lib/libnnz11.so
7f6f31081000-7f6f31180000 ---p 00289000 fd:10 2104768                    /u01/app/11.2.0/grid/lib/libnnz11.so
7f6f31180000-7f6f311c2000 rw-p 00288000 fd:10 2104768                    /u01/app/11.2.0/grid/lib/libnnz11.so
7f6f311c2000-7f6f311c4000 rw-p 00000000 00:00 0 Aborted (core dumped)
Regards
Siva Kumar

The permission looks fine. If it was permission issue then y it is trying to read the DATA disk which I havent created this time at all ( But created in the first installation).
2012-10-20 15:37:52.459: [ CRSMAIN][3563381328] Initializing OCR
[ CLWAL][3563381328]clsw_Initialize: OLR initlevel [70000]
2012-10-20 15:37:52.897: [ OCRASM][3563381328]proprasmo: *Error in open/create file in dg [DATA]*[ OCRASM][3563381328]SLOS : SLOS: cat=7, opn=kgfoAl06, dep=27140, loc=kgfokge
2012-10-20 15:37:52.898: [ OCRASM][3563381328]ASM Error Stack : ORA-27140: attach to post/wait facility failed
ORA-27300: OS system dependent operation:invalid_egid failed with status: 1
ORA-27301: OS failure message: Operation not permitted
ORA-27302: failure occurred at: skgpwinit6
ORA-27303: additional information: startup egid = 1000 (oinstall), current egid = 10002 (dba)
2012-10-20 15:37:52.967: [ OCRASM][3563381328]proprasmo: kgfoCheckMount returned [7]
2012-10-20 15:37:52.967: [ OCRASM][3563381328]proprasmo: The ASM instance is down
2012-10-20 15:37:52.968: [ OCRRAW][3563381328]proprioo: *Failed to open [+DATA].* Returned proprasmo() with [26]. Marking location as UNAVAILABLE.
2012-10-20 15:37:52.968: [ OCRRAW][3563381328]proprioo: No OCR/OLR devices are usable
2012-10-20 15:37:52.968: [ OCRASM][3563381328]proprasmcl: asmhandle is NULL
The only disks created are
[root@SFV9699 dev]# oracleasm listdisks
ASM_DATA
FLASH_RECOVERY
And these disks are showing part of that group also.. Not quite sure how this happened..
what abt dropping this group.. will anything work.

Problem with oracleasm

Hi,
I have a problem with oracleasm.
I marking disk /etc/init.d/oracleasm createdisk VOL1 /dev/sdb1
The marking disk "/dev/sdb1" was success.
*#Marking disk "/dev/sdb1" as an ASM disk: [ OK ]*
Next I create diskgroup DATA using VOL1 and leater create database using diskgroup DATA (VOL1).
Now I install EMC powerpuff and create link /dev/mapper1.
! dev/mapper1 = /dev/sdb1
Now I want to change disk /dev/sdb1 to /dev/mapper1 for VOL1 (in the VOL1 I have a production database)
Thanks for help

Hi,
as far as I have seen, Oracle redesigned a lot of their homepage.
This lead to a lot of problems with the download links (some asmlib libraries could not be downloaded from the homepage).
I assume that the error you are encountering hits into the same issue. Just that you are "updating" and getting a wrong URL instead of using the browser.
I would open a SR with support to get this resolved.
Sebastian

Cluster Database not starting up. Permission error.

Hi all,
I recently installed 2 node Oracle 11g RAC on RHEL5. While creating Clustered Database, database creation on second node (racnode2) failed. So, I connected */ as sysdba* on the node and executed startup only to get this error message:
SQL> startup
ORA-01078: failure in processing system parameters
ORA-01565: error in identifying file '+RACDB_DATA/RACDB/spfileRACDB.ora'
ORA-17503: ksfdopn:2 Failed to open file +RACDB_DATA/RACDB/spfileRACDB.ora
ORA-01034: ORACLE not available
ORA-27123: unable to attach to shared memory segment
Linux Error: 13: Permission denied
Additional information: 196612
Additional information: 10
SQL>But, *'+RACDB_DATA/RACDB/spfileRACDB.ora'* is present. I strongly believe it is a permission issue that ORACLE owned processes are not able to access disks owned by GRID user. I checked the permission of disks:
[oracle@racnode2 ~]$ cd /dev/oracleasm/disks
[oracle@racnode2 disks]$ ls -l
total 0
brw-rw---- 1 grid asmadmin 8, 65 Nov 19 19:15 CRSVOL1
brw-rw---- 1 grid asmadmin 8, 49 Nov 19 19:15 DATAVOL1
brw-rw---- 1 grid asmadmin 8, 81 Nov 19 19:15 FRAVOL1
[oracle@racnode2 disks]$And also, ORACLE user has asmdba among other privileges.
[oracle@racnode2 disks]$ id
uid=1101(oracle) gid=1000(oinstall) groups=1000(oinstall),1201(asmdba),1300(dba),1301(oper) context=user_u:system_r:unconfined_tCan someone shed light on what is happening? I am willing to furnish further data. Any help is highly appreciated.
Thanks,
...

Handle:      Flake
Status Level:      Newbie (10)
Registered:      Aug 10, 2007
Total Posts:      244
Total Questions:      51 (36 unresolved)
Location      Hyderabad ( India )
Occupation      Oracle Database Administrator
Try to close your thread please

Error building RT2860 WLAN driver in kernel 2.6.18-128.2.1.4.25.el5.i686

Hello,
I installed VM Server v2.2.1 (kernel 2.6.18-128.2.1.4.25.el5.i686) and am trying to build the RT2860 WLAN driver from source (2010_07_16_RT2860_Linux_STA_v2.4.0.0). I installed package kernel-ovs-devel-2.6.18-128.2.1.4.25.el5.i686 and when I run make I get the following compile error:
error: expected identifier or '(' before 'void'
The offending snippet of code, from a header file, is:
typedef VOID (*STATE_MACHINE_FUNC)(VOID Adaptor, MLME_QUEUE_ELEM Elem);
typedef struct STATEMACHINE {
ULONG Base;
ULONG NrState;
ULONG NrMsg;
ULONG CurrState;
STATE_MACHINE_FUNC *TransFunc;
} STATE_MACHINE, *PSTATE_MACHINE;
The odd thing is, I'm able to build the source when I replace kernel-ovs-devel-2.6.18-128.2.1.4.25.el5.i686 with kernel-devel-2.6.18-128.2.1.4.25.el5.i686 or with kernel-xen-devel-2.6.18-128.2.1.el5.i686 but then, of course, I get an "Invalid module format" error when I try to install the module (/sbin/insmod rt2860sta.ko).
The issue is probably very simple to solve, but I'm not much of a C programmer so it's not clear to me why the compiler is choking on the snippet above.
Thanks in advance for any advice,
Matt

This issue has been resolved. The problem was, we were (attempting to) use EMC PowerPath (/dev/emcpower* devices) but the default SCSI devices (/dev/sd*) were being discovered and used as path to storage.
The solution was to edit /etc/sysconfig/oracleasm and add "emcpower" to the ORACLEASM_SCANORDER parameter and "sd" to the ORACLEASM_SCANEXCLUDE parameter. Once we did that, failovers are working successfully.
-Mark

Import Error OVM Template Via VM Manager

I'm getting this import error message
Register an empty virtual machine
register the virtual machine genernal information
get the virtual machine detail information...
Invalid virtual machine type(HVM/PVM).
When tried to import OVM_EL5U5_X86_64_PVM_10GB
and OVM_EL5U2_X86_64_ORACLE11G_PVM
This was only my initial import on resource.
Can anyone help me on this?? thanks

Hi bach,
I can't follow you there... here's the extracted content of "OVM_EL5U2_X86_64_ORACLE11G_PVM.tgz"
oracle11g_x86_64_asm.img
README
System.img
vm.cfg
vm.cfg.orig
here's the README
OEL 5.2 X86_64 Oracle 11g image for PVM guests
Version 2.2
Released on Feb 02 2009
Changelog:
* Mon Feb 02 2009
- Bumped the release number from 2.1.2 to 2.2 .
- Replace system image with the image based on OEL 5.2 JeOS.
- Upgraded kernel to kernel-xen-2.6.18-92.1.22.0.1.el5, ocfs2 and oracleasm
were upgraded correspondingly.
- Added strace, gdb packages.
- Upgraded oracle-validated to 1.0.0-16.el5
- Moved Oracle home from LVM2 logical volume to regular ext3 partition.
how does this relate with your answer ?

Oracleasm 1.0.4 download

Hi everyone,
I am using RHEL 4 AS_ in VMware for the installation of the RAC. while I am Installing the oracleasmlib-2.0.2-1.i386.rpm
, I am getting the folling error:
#rpm -Uvh oracleasmlib-2.0.2-1.i386.rpm
error: Failed Dependencies:
oracleasm >= 1.0.4 needed by oracleasmlib-2.0.2-1.i386.rpm
My Kernal version is
#uname -r
2.6.9-5.EL
Also My kernal is not ELsmp.
I checked in the below site
http://www.oracle.com/technology/tech/linux/asmlib/index.html
but I am not able to find the exact oracleasmilib rpm form thre for the kernel 2.6.9-5.EL.
Can you please give the direct link to download the particular rpm and its supporting rpm's if needed.
Thanks in Advance,
Elice.

For 2.6.9-5.EL Kernel, download 2.6.9-5.EL or higher and it will work.
If you know the dependencies follow the order, otherwise use below command.
rpm -ivh oracleasm-support-version.arch.rpm oracleasm-kernel-version.arch.rpm oracleasmlib-version.arch.rpm
Regards
Satishbabu gunukula

Oracleasm error

Similar Messages

Maybe you are looking for