P55-GD45 voltages

Hi,
I got a new computer using the GD45 MB and an i7-860 processor. I am running CPUID hardware monitor and SpeedFan and both report strange voltages for the motherboard: 9.7V for the 12V rail, 5.6V for the 5V rail, 0.95V for the 1.5V and 0.76V for VRAM (memory is supposed to be at 1.5V). Is this normal? Am I having problems with the power supply? I am not overclocking, everything is at default. I am also a bit worried that the system is intermittently stuttering (mouse/sound/video lag of a couple of seconds every couple of minutes).
In summary, are these voltage readings sign of a problem?
Thanks, Florin

Quote
One of the features of this board (boldly presented on the official web page) is the presence of many voltage sensors to monitor the board.
You have misread the logo for that feature:
It does not mention any sensors.  What is indicated on the product site are voltage measuring points to which you can hook up a voltmeter/multimeter.
They should be marked on the board.  On the following picture you can see the measuring points for CPU VTT and CPU voltage:
[picture attached to the post]
The Check points for DDR & PCH Voltage should be marked on the board as well.

Similar Messages

  • P55 GD45 won't boot

    Recently bought a brand new P55 GD45 got it to boot fine the first time re-installed OS and everything.  Started looking at the bios and saw the option to turn on OC Genie, hit save and exit next thing I know my comp goes through a boot cycle but doesn't show anything on-screen and reboots itself.  Tried to clear the CMOS reset the jumpers, and took the battery out and this thing still won't boot .  Am I not clearing the damn CMOS right or something?

       >> Clear CMOS Guide <<

  • P55-GD65 Voltage Discrepancy

    Why is the voltage variance of this board so high?  With low Vdroop enabled on a voltage of lets say 1.36 in the bios I get a 1.40v reading in CPU Z @ idle.  This turns into 1.42 or more under load. Am I missing a setting that will keep it closer to what I set it at?  This variance is rather ridiculous if you ask me.  I have all the standard power saving features turned off before anyone asks. 
    Thanks! 
    My System:
    Mobo: MSI P55-GD65
    CPU: Intel i5 750
    GPU: Ati 4870x2 2 GB
    Mem: 2X 2 GB G.Skills Ripjaws DDR3 1600
    SSD: OCZ Agility 60 GB
    HD: 2x WD Black 500gb ea Raid 0
    PSU: PC P&C Silencer 750

    Songokussm the same issues I reported to support, they responded to me, that my MB is faulty and I should RMA ( did it twice, 4 month without MB ) I prove them otherwise, I had 3MB P55-GD65 with the same issues. Short speaking every MB with ERP=040 is faulty on engineering level Overvoltage like you described, problems with fans on sysfan1 and sysfan2, restore AC on power loss not working correctly and sometimes USB2 stops responding.
    My conversation with MSI support ended when they statement that they can`t check if I`m correct because they don`t have MB with ERP=040, so the problem is .... gone  I bet that with bios 1.9 in your case issue still occur but is`t less "visible".

  • P55 GD45 load line calibration option missing

    Hi guys. So I just flashed to the newest MSI bios for this board because I was having OC issues. Bios version 1.10/1.A from the 1st of March 2011. Now I don't see a load line calibration option above the CPU voltage control. Is it integrated or does the new Bios compensate for vdroop some other way? Please let me know, thanks.

    https://forum-en.msi.com/index.php?topic=139777.0

  • BIOS doesn't change CPU Voltage P55-GD65

    I have a P55-GD65 with BIOS Ver 1.7
    No matter what setting I put the the CPU voltage it seems to run in auto only.  I have tried many combination's of settings that I have read on the forums but nothing seems to be working.
    Has anybody had this problem?
    Thanks,
    Mark

    Yes even when I have Intel C-STATE and Intel EIST disabled.
    The voltage is much lower.  I can't over clock because I cannot up the CPU voltage.  I have the CPU multiplier at 21 and the clock at 155.  If I go even up to 156 on the clock my system will blue screen.
    When I put the voltage in Auto and monitor it and then put it in manual and crank it up to 1.45 and monitor it the voltage behaves as it is in auto.  I have XMS 1600 memory and the Mugen B rev 2 cooler so I know that is not an issue.  I might have a defective MB.  I've been building PC's for years so I'm not a newbe.  I've usually used Supermicro boards and this is my first MSI board.  The board is very nice and if it worked it would be great.  I was going to build another system with that board but am a little gun shy now.
    Thanks for all your help.
    Mark

  • MSI X79MA-GD45, Bios 3.2, ddr Voltage + multiplier

    Hi, I just updated to the 3.2 bios on my brand new MSI X79MA-GD45 board, so not sure if it's the bios or something weird with the board overclocking.  In the main overclock menu I can change ddr to the xmp or run linked and specify 1600, 1866, or 2133 etc (I also have access to the timing screen).   Under the DDR voltage section it is locked and it just stays on auto (there are no [] brakets around it indicating you can change the value), same thing happens with the CPU multiplier, just stays on auto and unable to change it.  Kind of pointless if I can change my ddr to 2133, but can't specify voltage to make it run stable.
    Is there an overriding setting I need to enable or disable to change these values?  I noticed that under the OC genie section it would let me change them all though, I would like to do the changes manually without using OC genie settings.
    Thanks.

    You have to use the keyboard numbers pad + and - keys to change the values. 

  • P55-GD80x, OC Genie, voltages too high?

    Hello and first off let me thank all the MSi staff and and more importantly the product designers for making such greats board, this P55-GD80X board is fantastic
    This is not my first MSi purchase and probably wont be the last, the community support seems much homier.
    Alright down to the gritty. Im usually a GPU overclocker (XFX 5870) 860/1200, its locked at 900/1200. Only solution ive found is to flash the BIOS to another card so it unlocks it.
    All that is irrelevant, hope you're all still following me here.
    The OC Genie function really intrigued me, i was never one for CPU clocking or MEM oc'ing but it was rather simple. As its known, press of a switch, turn the comp on and bam, its overclocked.
    Heres where the problem comes into play
    The above pictures are both at DEFAULT values, first picture is idle, second is under load.
    So i guess as you can see, under load the voltage goes down a bit.
    Now heres for the OC genie results
    First picture is of idle results AFTER OC Genie, second is load results. Third pic is the memory overclock it did.
    Again as you can see the CPU voltage drops under load, but running 1.4v at idle after apply OC Genie?
    seems a bit off right? I also have HT off and Intel Turbo Boost off.
    Is it normal for the voltage to get higher on idle then go down under load?
    Cause i've seen some posts where people are getting around my speeds
    with around the same voltage i have UNDER load with OC Genie (1.3V)
    Is this anything i should be concerned about? and if theres a fix please help a brotha out.
    My chip idling at 1.4v+ just seems insane.
    Also have a CNPS9900 CPU cooler on it, temps arent really an issue.
    If anyone will PLLEAASEE help me out, or explain to me what i have to do to get this in worrying outa my head.
    NEW to CPU oc'ing, not so much with GPU. So please dont leave any tips or full steps out.
    Thanks in advance guys  !!..Will be checking this thread very frequently.
    My rig.
    i7 870 Lynnfield
    Kingston HyperX 8GB (4x2)
    P55-GD80 Xtreme Edition
    XFX Radeon 5870
    CM Silent Pro 700watt PSU
    1TB HD
    EDIT: Also, im unable to change the voltages in the bios AND the MSi control center, theyre both greyed out.
    Even in the bios the CPU voltage is in red (red meaning bad obviously lol)
    Im at the point where if enabling OC Genie is gonna cause me problems down the road, then i just wanna forgettabout it.
    Also a point, without OC Genie enabled im able to change the voltages, problem is im just not adequately
    knowledged enough to start from scratch and entering all the values (hence the OC Genie seeming like pure gold)
    Also, whats the deal with all the phase controls in the BIOS? should these ALL be disabled or enabled? i've heard alot of mixed results.
    Sorry for writing a novel guys, just trying to give you the most information i can.
    Nothing worse than going into battle without good intel (no pun intended).

    Quote from: COMEDOR on 08-July-10, 10:37:18
    and @DaLoon i actually do use msiafterburner!, it still limits me to 900ghz. I've been told that all XFX cards, or the ones i've seen at least are locked at 900.
    I know they can be unlocked by flashing to ASUS or GIGABYTE, i mean i cant even change the voltage in afterburner, the tab literally doesnt exist.
    Mmmm odd,
    read this then:
    http://www.overclockers.com/hd-5870-bios-flashing/
    Its about the flashing you're talking about.
    Remember, you do this at your own risk, if you decide to go ahead on it, I, nore anyone here is responsible if something goes wrong.
    Good luck and keep us posted.

  • X79A-GD45 Plus refuses manual voltage overclock?

    Hello everyone, I registered over here to ask this question and see if anyone else is having the same issue.
    I currently have an i7 3930k installed in my GD45 Plus, I bought the board for its reasonable price and 8-DIMM support. I was pretty happy with it until I discovered this "issue".
    Leaving most settings on auto and using the Turbo+Vdroop method (C'mon MSI, would it kill you to add offset overclocking?), 87.5% Vdroop control and +250 on the core override voltage I am able to stress test for 30 minutes to an hour at 4.6ghz before crashing, the CPU is just at the very edge of stability. Load voltage settles around 1.364V with this setup, which is very very low for SB-E chip at that clock speed.
    However, if I disable turbo and run a manual clock of 4600mhz things change. All power savings shut off, SA voltage at 1.300V, basically everything opened up as far as power limit/duration settings. It boots to windows fine, but immediately upon loading the CPU the system shuts off and reboots after a few seconds. I tried 4600 at 1.375V... then 1.400V... then 1.450V, all the way up to 1.550V and it has the same effect.
    Then I wondered what it would do at stock, sure enough even at 3200mhz stock with a manual voltage the board shuts off immediately once the CPU is loaded up with Prime 95 or IBT.
    I am using BIOS revision 17.3, and am about to attempt to downgrade to a previous version to see if that has any effect.
    Does anyone have any idea what might be wrong with this thing? This is incredibly disappointing, as I had a very good experience with the X79MA-GD45 mATX board. What is even more disappointing is my garbage (literally the worst board I have ever owned, bar none) ECS X79R-AX Deluxe that doesn't even have a VRM heatsink and needs the BIOS jumper in the reset position to even boot will run the same exact CPU as I am using in the Plus at 4.8ghz all day every day. Really want to get this board working properly as I like everything else about it.
    System specs, just in case:
    -C2 Stepping i7 3930k w/H100i
    -MSI X79A-GD45 Plus
    -32GB G-skill DDR3 1600 CAS8
    -2x MSI HD7950 TFIII
    -Cooler Master V1000 PSU
    -Samsung 830 128GB SSD
    -Windows 7 Pro 64 bit

    Quote from: PirateDog on 07-September-13, 11:54:22
    MSI X58's had it, and it now has a big time presence in the Z87 lineup.
    I haven't tried the Z87 boards yet from MSI (Used several Gigabytes and Asus though) but I'm glad to hear they listened. That was what prompted me to get rid of my Z77 MPower, I had a 5.2ghz capable chip but I did not want to run it there 24/7.
    Quote
    For an everyday machine, industry recognized suggested limit for Sandy-E CPU is 1.350v's. Use the Turbo OC method on Auto CPU V., EIST and C1E enabled. Enhanced Turbo enabled, and VDroop at 100%. Internal PLL Overvolting set to enable. Might have to increase SA, I/O, and PLL V. some. Are the settings in CPU Features increased? Overspeed Protection disabled? Get what you can out of it and that is about all you can expect. G45's aren't known as good OC'ers like GD65(8D's) or Big Bang XPower II's!
    I've gone through literally everything. This is not my first time doing this, and I know good overclocks are possible on a GD45 board as I've done it before with arguably the worst of the bunch. I'm not bugged about voltage, I prefer to stay under 1.500V if possible and would only push past that for quick bench runs.
    Quote
    Just asked an uncle what his 3930k C2 runs 46X Turbo OC, VDroop 100% at, and his under IBT will hit 1.384v's peak, and it is perfectly stable with 16GB RAM at 2400.
    Don't recommend to go down too far to a UEFI/BIOS with ME 7 FW once ME 8 FW has been installed, or you may create all kinds of HECI mismatch problems. If no crashes or BSOD's, other than when stressing with Prime or IBT, no problems in everyday work, applications, or programs, use it and not sweat the small stuff. 
    I did some more experimenting, and I think the BIOS might be incorrectly reporting the voltage. I found that I can run 4400mhz at only 1.150V and 4600mhz at 1.200V, there is no way a 3930k with a 1.341V VID is overclocking by 1000+ mhz undervolted like that. It would make sense, if it was about 0.200V off then running 1.400V would actually be 1.600V and even with the power settings tweaked it would instantly shut down unless I was sub-zero, probably due to the VRM's hitting the 130* thermal protection. I can't think of any other reason it could be behaving like this.

  • Voltage @ 4Ghz on i5/P55-GD65

    I'm particularly wondering what  PCH 1.8 and PCH 1.05 should be set to.
    I feel uncomfortable with them set to auto, as I have no idea what they are under load.
    Current voltage settings.
    Vcore - 1.326
    VTT - 1.314
    DRAM - 1.65
    BUS - 200 / Ratio - 20
    DRAM Freq - 2000 / Ratio - 5 / Timings - 9-9-9-27 88 1T
    QPI Freq - 6400 / Ratio - 16
    Spread Spectrum - Disabled
    Load Line Calibration - Disabled (If enabled, I have to set Vcore higher then 1.40 to run P95 error free.)
    Also, What're these voltages "related" to?
    --I made your image clickable to the larger size.
      Click the modify button to see how I did it.
    --Mike 

    Most likely false readings.  I wouldn't be concerned.  The software may be interpreting some other sensor/components on your board and translating them to this information.  Again, I wouldn't be concerned.  Here's my HW Monitor screenshot.

  • P55M-GD45 Vcore Voltage Help

    I've read the sticky, I know about pg up/pg dn and the +/- keys.
    My problem is that I can't manually set the vcore voltage in the Cell Menu. It says Auto (greyed out) and when I do pgup I can increase the voltage up to about +.303, but it doesn't allow me to manually set the voltage, nor undervolt it.
    I've updated the BIOS to 1.8, but still no luck.
    If anyone has any suggestions, please help.

    Quote
    I honestly wish the mobo had manual vcore control.
    Well, it does.  You said so yourself:
    Quote
    "Cpu Voltage" it is either Auto (Grey) or increasing the voltage in increments.
    Quote
    I didn't increase it +.303, I was only specifying the limit of what it would allow me to change.
    To be honest, I fail to see the problem you are having with the voltage.  That means that either I am terribly misunderstanding what you are trying to say or that you are misunderstanding the way the voltage settings work. 
    Can you please try to elaborate what exactly it is you are trying to do with the system?  It is irrelevant at this point, what the system will be used for.  What is of importance is what clock speeds you are trying to run the system with, what exact settings result in an unstable system and which settings have been working for you.  Within a certain clock speed range from the default settings, increasing the core voltage of the processor may not even be necessary.  It all depends on what you are actually aiming for.
    In terms of current system settings, you have not really told us much so far:
    Quote
    Failed OCCT during a 2hr test.
    Under what operating conditions? Base Clock Speed?  Memory clock speed?  Memory voltage?  Memory timings (post CPU-Z screenshots [SPD & Memory]? CPU Voltage [as shown by CPU-Z]? Other Cell Menu Settings you modified? etc.

  • MOVED: P55M-GD45 Vcore Voltage Help

    This topic has been moved to Overclockers & Modding Corner.
    https://forum-en.msi.com/index.php?topic=142727.0

    Quote
    I honestly wish the mobo had manual vcore control.
    Well, it does.  You said so yourself:
    Quote
    "Cpu Voltage" it is either Auto (Grey) or increasing the voltage in increments.
    Quote
    I didn't increase it +.303, I was only specifying the limit of what it would allow me to change.
    To be honest, I fail to see the problem you are having with the voltage.  That means that either I am terribly misunderstanding what you are trying to say or that you are misunderstanding the way the voltage settings work. 
    Can you please try to elaborate what exactly it is you are trying to do with the system?  It is irrelevant at this point, what the system will be used for.  What is of importance is what clock speeds you are trying to run the system with, what exact settings result in an unstable system and which settings have been working for you.  Within a certain clock speed range from the default settings, increasing the core voltage of the processor may not even be necessary.  It all depends on what you are actually aiming for.
    In terms of current system settings, you have not really told us much so far:
    Quote
    Failed OCCT during a 2hr test.
    Under what operating conditions? Base Clock Speed?  Memory clock speed?  Memory voltage?  Memory timings (post CPU-Z screenshots [SPD & Memory]? CPU Voltage [as shown by CPU-Z]? Other Cell Menu Settings you modified? etc.

  • Running your memory the right way/ running 4 DIMM slots on P55 boards

    Dear Forumers,
    Lately there are a lot of questions, about motherboards from the P55 range not starting on first boot.
    This could be due to wrongly arranged memory DIMM's in your slots.
    Some people out there, like me, were convinced that you could choose either dualchannel.
    Well, its not the case.
    Like I was pointed out earlier, you must use a certain slot, otherwise the memory will not be detected properly.
    According to Intel specs, DIMM0, must always be populated.
    This means that to run dualchannel with only 2 DIMM's, that you must check your manual and look carefully which slot is for DIMM0.
    According to the manual, it will be slot DIMM1 on your board, but watch out, this is not the slot closest to cpu, on current MSI P55 boards, (CD-53, GD-41, GD-45, GD-55, GD-65, GD-80 and the Big Bang Trinergy), its the second slot from cpu.
    Picture of P55 mainboard:
    From a manual from a MSI P55 board:
    So for dualchannel with 2 sticks, you must populate the black slots, DIMM1 and DIMM3 and for single channel with one stick DIMM1 most be used.
    Please bear in mind that DIMM0 in Intel spec.sheets means DIMM1 on your board.
    The link to technical sheet from intel about : i7 8xx cpu's
    http://download.intel.com/design/processor/datashts/322164.pdf
    A short quote with the relevant data:
    Quote
    Rules for Populating Memory Slots
    In all modes, the frequency of system memory is the lowest frequency of all memory
    modules placed in the system, as determined through the SPD registers on the
    memory modules. The system memory controller supports one or two DIMM
    connectors per channel for unbuffered DIMMs. For dual-channel modes, both channels
    must have at least one DIMM connector populated and for single-channel mode only a
    single-channel may have one or more DIMM connectors populated.
    Note: DIMM0 must always be populated within any memory configuration. DIMM0 is the
    furthest DIMM within a channel and is identified by the CS#[1:0], ODT[1:0], and
    CKE[1:0] signals.
    For more info, please read datasheet
    Also, let me remind you that this goes for ALL P55 boards out there, its not just an MSI thing.
    This has to do with the fact that the memorycontroller now sits on die on the Lynnfield cpu's.
    Im hoping to end the debate, like I had (and I was wrong), about the fact that you should be able to use any channel, like you could on the S775 boards, you just cant anymore.
    Update 26 december 2009:
    Running all 4 DIMM slots with memorysticks
    It seems that a lot of people are having problems running with all memoryslots occupied, e.g. not booting, BSOD and other crazy stuff.
    If you have such problems try the following first, before running back to the store to swap stuff out.
    - Raise Vdimm to 1.65V, its still a save voltage for the board and this way the memory gets a little more power and in 99% of the cases, this will solve the issue.
    - Try booting/installing with one stick first in DIMM1 on the board  (see above).
    - If it boots/installs, let it go all the way till windows is done.
    - Turn off pc and add a second DIMM in DIMM slot 3, restart and let i boot all the way again in windows till its done.
    - Do the same again for DIMM2 and last DIMM4.
    We know its a bit of a hassle, but it worked for a lot of people, so be sure to try this before anything else.
    And again, its not just an MSI thing, there are more manufacturers out there with the same issues, this also has to do with the fact the memorycontroller now sits on die with cpu.
    I'll edit if new boards come out.
    --I made your images clickable
      Click the modify button to see how I did it.
    --Mike

    Upgrading Mother Board (P55-GD65 with i3 processor) BIOS [/b] from 1.3 to 1.6 corrected my Computer re-starting soon after the Boot sequence began.  Putting the four 2GB RAM in one at a time in the suggested order in sequence with the socket numbers fixed the problem earlier, but only for the next, one boot.  The problem then returned as long as all 4 DRAM were installed.  Raising the DRAM voltage did not improve things. 
    I used the Forum's program for flashing the new version of Bios using USB Flash Memory for boot into DOS.
    Thank you, DaLoona, for your post notifying me this had to do with the motherboard and was probably not a failure, but a "normal" occurance in certain conditions.  I was no longer inclined to return the board and perhaps end up with the same error in the replacement, and no longer worried about the rebooting doing damage. 
    In Bios Setup I had already reduced an entry to do with number of overclocking tries from 3 to 1 (the minimum choice) which reduced the number of re-boots to 1.

  • Problem with sound in p55 gd65

    hello
    i have a problem in my system and i dont know its from mainbord or other devices
    when i playing game or watching movie,suddenly the sound is cutting down(stoping) and cpu usage going up(25 or 30 %)
    in game i had no sound and game play was with tik and also in watchig film
    this problem is not always happend but im comfused
    main msi p55 gd65,cpu intel core i5 2.66 ghz,ram 4gb ocz 1033,graphic ati 5770 sapphire,power icute 950w,hdd WD 1tb

    Use MSI Afterburner and set lower or fixed clocks for the graphics card.Enable Unofficial OVerclocking and set a fixed 2D clock to be applyed at start up ,see what happens.
    Play a little with the 2D/3D clocks.I ve saw somewhere on a forum a issue with a similar mobo from some other vendor and another video card.The problems of that user stopped when he lowered the clocks of the video card.
    You are using a 5770 which does a lot of frequency/voltage switching while in desktop.

  • Can't Enable XMP after BIOS flash to V1.4 on P55-GD85

    I didn't put this in the BIOS section because while the BIOS is involved,  I don't think it's necessarily a BIOS issue.  However, if it should go there please move it.
    While not new to computers by any stretch I committed the cardinal sin of updating my BIOS when I didn't absolutely have to.  While their were some issues I'd hoped would be fixed with a new BIOS revision, they weren't critical. 
    I have a i7 860 Lynnfield system running Win 7 Home Premium 64 with a MSI P55-GD85 mobo which has been running fine since being built in March of this year.  This was the first BIOS flash since I've built the system.  The system came with either V1.0 or V1.1 (I think it was V1.1).  I checked using Live Update (yes, I now know this is bad) and found there had been several udpates since my current version.  I went ahead and used Live Update to flash the BIOS (yes, I know...not a good idea).   Contrary to the horror stories the flash itself went fine.  I watched it flash the BIOS and everything verified fine.  Of course  after the update I had to reset my BIOS settings to get the system to run which went fine.  The problem is that the one thing I can't do is enable the XMP option for the memory without the system crashing.  If I enable this option the system will POST and then do a memory dump before ever getting to the desktop.  Without turning this option on I can't take full advantage of my RAM.  I am running G.SKILL Trident 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 2000 (PC3 16000) which are XMP compliant and ran without issue up until the BIOS update.  It is possible that there is some other setting that I didn't reset after the BIOS change to allow this to work that I am missing.  I know I did a bunch of tweaking and changing of settings trying to get things to run correctly when I first built the system.  I've gone over and over the BIOS and can't find anything else to try to get me to allow to enable the XMP option without crashing.  By simply enabling that option my system would normally run stable at about 3.6-3.7GHz. 
    Does anyone have any ideas as to why this might be happening or what I can do about it?  About the only other thing I can think of is to reflash the BIOS back to a previous version to see if that helps.  I am sure there is something I am missing as there is no reason the BIOS shouldn't allow the XMP feature to be enabled without crashing.  Any help would be most appreciated.  Thanks. 

    Have you try to increase your RAM voltage to 1.55v ~1.6v?

  • Problem with CPU Voltage

    Hello
    I build new PC with:
    i5-760
    Noctua NH-D14
    MSI P55-GD65
    G.Skill 2x2GB CL7 ECO
    Antec TruePower New 750W TP-750
    TwinTech GF 9600GT
    I have problem with CPU voltage as even when I set it for example to 1.201v in bios, under load it overshot to 1.256-1268. The best is when I oc`ed cpu to 4GHZ and set voltage in bios for 1.30v it overshot for 1.45v+! Not to mention that temps are skyhigh from that. It doesn`t matter if I try to put BIOS Vcore on 1.1v on stock because under load it still rise to 1.16. I turned off all eist, c-state, turbo boost, phase led and switch phase, set vdrop to low and still something is wrong here. I updated the bios under dos from USB stick to newest 1.9 version in order to update CPU micro code without error and it not helped. I want to know is that even possible to fix or should I RMA MB or CPU.
    Minor problem is with sysfans as they power on for a second and turn off instantly to start working again when I see list on devices in post. After rebot when my monitor is switched off it takes something like 5 sec to power monitor on and another 5 to show bios, is that normal?

    I have similar issues, it's hard to tell which measurement is the most accurate, there are 2 different measurements in the control center that don't match up with the figures set in the bios.  The only way to be sure would be to get an expensive accurate multimeter but If you're only interested in running a stable overclocked computer without knowing the exact figures then get the computer running stable and lower the voltages until it starts to become unstable with prime95,
    Or you could work the other way round, set the voltages so it boots but doesn't run prime95 for long, then raise the vcore and vtt one at a time until your happy with the length of time prime95 runs without errors.  I'd be happy with 24 hours, I seem to remember errors creeping in at around the 9 hour mark on the setting below what I have it set to now.

Maybe you are looking for