P7n platinum: memory errors when overclocking

I have a p7n sli platinum and I'm trying to get my e8400 overclocked. The chip is stable at 4150 mhz and did prime 95 small ffts for an hour with no problem. However, games crash and the vista memory diagnostic shows errors. I have ddr2 800 memory that runs at 4-4-4-12, so it should have some room to overclock with looser timings. However, overclocking it and running it at a 1:1 ratio still gives errors.
The really bad part though, is that if I run my memory not at 1:1 so it can stay at its 800mhz rated speed, I still get errors. Does anyone know if this motherboard has a problem running memory not at 1:1 even though it's supposed to be able to? I've tried messing with all sorts of voltages and timings. What are the chances getting some 1066 ram and running it at 1:1 would fix the problem?

Alright, I got the rest of my stuff listed. I don't think there's anything wrong with the memory because it's perfectly fine running at 800mhz when the FSB is 400, and I tested it not too long ago when building the system for my q6600. As for the slots, I have tried slots 1&3, slots 2&4, and all slots full with roughly the same results.
Now that I think about it, it's more likely the board causing me to FAIL than the memory itself. There's no reason the memory should have problems running at 800 or below regardless of what I have the FSB set at. I did stumble across a post saying that this board doesn't like memory not on the compatibility list when overclocking, and I don't think the patriot is on the list. Any ideas on if corsair dominator could run on this board at its rated 1066 speed? Also, do you still think I should update from the p04 bios?
edit:voltages are
VTT: 1.4
Vcore: +.250 (for around 1.35 total under load after vdroop)
NB: 1.4
SB: auto

Similar Messages

MOVED: P7n platinum: memory errors when overclocking

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=118116.0

Alright, I got the rest of my stuff listed. I don't think there's anything wrong with the memory because it's perfectly fine running at 800mhz when the FSB is 400, and I tested it not too long ago when building the system for my q6600. As for the slots, I have tried slots 1&3, slots 2&4, and all slots full with roughly the same results.
Now that I think about it, it's more likely the board causing me to FAIL than the memory itself. There's no reason the memory should have problems running at 800 or below regardless of what I have the FSB set at. I did stumble across a post saying that this board doesn't like memory not on the compatibility list when overclocking, and I don't think the patriot is on the list. Any ideas on if corsair dominator could run on this board at its rated 1066 speed? Also, do you still think I should update from the p04 bios?
edit:voltages are
VTT: 1.4
Vcore: +.250 (for around 1.35 total under load after vdroop)
NB: 1.4
SB: auto

Memory error when trying to fetch events by data range

I keep getting the following memory error when trying to fetch events from my calendar server: CAPI_STAT_SERVICE_MEM_ALLOC
I have checked the forum and found only one entry that talks about adjusting the -mx -oss settings for my JVM. However it is unclear if this change needs to be done to the server or the client where I am running the JVM. I have made these adjustments in my JDeveloper project and I still recive the error. I have checked the eng.log, cws.log and snc.log. The only entries found are:
DATE = Thu Jun 2 16:53:24 2005
PID = 12647; TID = 3076395840
Trying to connect: Host = houoas2.us.oracle.com (127.0.0.1)
Service = unidas
DATE = Thu Jun 2 16:53:29 2005
PID = 12647; TID = 3076395840
Connection established: Host = houoas2.us.oracle.com (127.0.0.1)
Service = unidas
This is being done on a 10g calendar server. Any help would be appricated.

Now that 10g and its associated CSDK are out and the 9.0.4.x CSDK is presumably frozen, would it be possible to make the 9.0.4.10 CSDKs - for each platform - available for downloading, unbundled from the massive server suite?

[N95 8GB]Out of Memory error when opening 15MB pdf...

What is the file size limit when opening a pdf file? I have a 15MB pdf file that cause 'Out of memory' error when I opened it with the PDF Reader that comes with the phone.
Thanks.

Hi,
It seems that problem is file specific, so could you please share a file with me. I sending you a private message.
Regards,
Anoop

Indesign cs5 'out of memory' error when using preflight

I have been regulary getting an 'out of memory' error when i choose to use my bespoke preflight profile.
I have 4gig of ram and run Indesign CS5 on OS 10.6.8.
Does anyone know a work around?
As soon as I select from the basic default profile, i get the beach ball from hell for 10mins, then it kindly lets me know that I am out of memory, sends a crash report to Adobe and then asks if I want to relauch. I'm stuck in a vicious circle. I must of sent my 4th crash report now and no feedback from anyone at Adobe.

I have replaced my preferences, but still the problem persists. I have tried switching my view from typical display to fast display before i selected a profile. I thought this may give me the extra memory I needed to avoid the enevitable crash. I learnt that 2 files were indeed rgb instead of cmyk before it crashed again. So I switched them to cmyk and tried again, selected my bespoke profile, but yet again it crashed. I think the problem lies with the file, not Indesign, as i have tried the same profile on a different file and the program doesn't crash and runs as it should. So if in future I need to use said crashing file again, firstly i will need to try Peter's isolate fix method. Otherwise i'll never be able to progress to successful a pdf.

Memory Error when trying to paste art into PS CS4 vanishing point grid

I get a memory error when trying to paste art into PS CS4 vanishing point grid.
"Photoshop.exe application Error The instruction at 0x7755886b referenced memory at 0xffffffff. The memory could not be read. Click on OK to terminate the program"
I have plenty RAM, HD space, and virtual RAM/Cache in PS prefs.
Any suggestions?

Try disabling the Aeros theme by selecting one of the Windows Classis Themes under desktop customization. This seemed to fix the problem for me.

Out of memory error when sending messages

Hello!
I have OS X 10.4.10 and I have an email account setup (IMAP)in mail.
Lately when I go to send a message, I get an "Out of Memory" error that it says is coming from the mail server, but I know for a fact that it's not a server issue (mail account works on a PC fine). If I try to send it again it goes through just fine.
Any ideas?

You are building an HTML table with 1500 rows? That is definitely a lot. And I assume you are also putting some styling on that table...
These days programmers resource to [url en.wikipedia.org/wiki/AJAX]AJAX techniques for things like that.
You can, for example, send the table data as a list of comma separated values, and then use Javascript on the browser to create a partial table with options to browse through the different pages of data.
If you need to show all that data in one single page, you can still try sending just the data as CSV or XML and then building the table on the browser via a Javascript loop. Use CSS for the styling so you don't overload the HTML code with styling information.
Marcos Broc
Hi,
I have a bit of a problem. I?m trying to generate
quite a large JSP file (a table with about 1500
rows). The problem is that I get an out of memory
error when the JSP is being generated. And it is
definitely that the JSP is too large, or rather the
HTML being generated from it. Now I was under the
impression that the JSP page was flush now and again,
but I tried to set all the different flush options
and I have also tried to manually flush the page.
Nothing of this made any difference except for
displaying a white page instead of an error page
since the header was already sent. Now this suggests
to me that the page is being cached internally by the
server and then sent to the client. So is there
anything I can do about this?
Regards
Hertz

Out of Memory Error when generating JSP

Hi,
I have a bit of a problem. I?m trying to generate quite a large JSP file (a table with about 1500 rows). The problem is that I get an out of memory error when the JSP is being generated. And it is definitely that the JSP is too large, or rather the HTML being generated from it. Now I was under the impression that the JSP page was flush now and again, but I tried to set all the different flush options and I have also tried to manually flush the page. Nothing of this made any difference except for displaying a white page instead of an error page since the header was already sent. Now this suggests to me that the page is being cached internally by the server and then sent to the client. So is there anything I can do about this?
Regards
Hertz

You are building an HTML table with 1500 rows? That is definitely a lot. And I assume you are also putting some styling on that table...
These days programmers resource to [url en.wikipedia.org/wiki/AJAX]AJAX techniques for things like that.
You can, for example, send the table data as a list of comma separated values, and then use Javascript on the browser to create a partial table with options to browse through the different pages of data.
If you need to show all that data in one single page, you can still try sending just the data as CSV or XML and then building the table on the browser via a Javascript loop. Use CSS for the styling so you don't overload the HTML code with styling information.
Marcos Broc
Hi,
I have a bit of a problem. I?m trying to generate
quite a large JSP file (a table with about 1500
rows). The problem is that I get an out of memory
error when the JSP is being generated. And it is
definitely that the JSP is too large, or rather the
HTML being generated from it. Now I was under the
impression that the JSP page was flush now and again,
but I tried to set all the different flush options
and I have also tried to manually flush the page.
Nothing of this made any difference except for
displaying a white page instead of an error page
since the header was already sent. Now this suggests
to me that the page is being cached internally by the
server and then sent to the client. So is there
anything I can do about this?
Regards
Hertz

P800 "Not Enough Memory" error when trying to use Contacts

Now even after I reset my P800 from iSync I get this 'Not enough memory' error when I try to use my contact list.
This is getting really frustrating! I want to downgrade...

I suspect it's the feed as I've just tried it and the latest episode fails. Try contacting the Podcast's producer/publisher to let them know, since they may not. From your linked page, click on their name and follow that to their website, where you should find contact details.
By the way, even if the problem is with iTunes, it's still down to the producer/publisher to rectify it, which is why I suggest you contact them
Phil

P7N platinum sli and qx9650 overclock issues

Hey all,
Just wondering if someone could help me with overclocking my qx9650 on my P7N platinum sli.
I have tried throwing all kinds of voltages at the cpu, fsb, and nb and I still can't run stable for over a few seconds. I thought it might be due to a fsb hole and have tried a range from 1550-1650. My goal is to get it at 400mhz(1600 in bios) and get a 5:4 ratio with my ram at 1000. I tried updating to the p06 performance bios from ami 1.3 and still can't get it stable. I don't want to end up frying my board. I got it to run stable at 350 for an hour in prime 95 but would really like to achieve 1600. at 350x8.5 for 1500 my temps did not get above 54c under full load
I am not looking for a huge oc, just get to 9x400 for a 3.6 ghz clock speed for 24/7 use. I ran prime 95 for 5 hours with everything at stock so I know it is not a bad cpu, ram, mobo. I also ran memtest86+ at stock and every test passed. I have d.o.t disabled, eist disabled, and spread spectrum disabled.
Memory timings right now are 5-5-5-18-2T at 2.1v and memtest+ passed with those settings at speed 800mhz.
any suggestions would be great

just wanted to let everyone know that i got it stable at 3.75ghz for 26 hours in prime 95. Don't know why but it still won't boot from 1550-1650 (must be a FSB hole or something) so i just put it at 1500(375) with a 10 multiplier and ram at 1000 for a 3:4 fsb:ram ratio.

Memory error when executing package through SQL Server Agent.

Hi!!
I have a problem with a package (SSIS) when run on SQL Server Agent.
The job is configured
with the proxy and the account has the
required privileges. Runs perfectly
if the job runs manually, but if I let it
run on schedule I get a memory error.
Also if I run the
package through DTExec.exe or VS2008,
everything runs smoothly.
I am using SQL2008R2.
If someone has something similar happened
and have found how to fix it please i need
to know how.
Thank you.

This is most likely your issue:
http://support.microsoft.com/kb/824422

Out of Memory Error when Saving SequenceFile generated using API

I am currently developing an application that creates a SequenceFile using .NET 4.0, C# (2010), Windows 7 Pro x64, Dual Core 2.5 GHz, 3.0Gb Memory. Using the API EngineClass, I create a complete SequenceFile based on user/file inputs and then save it to disk. When I'm done, I save using SequenceFile.Save() and then release using ReleaseSequenceFileEx().
For smaller files, there is no problem. For larger files, I sporadically get the following error:
System.Runtime.InteropServices.COMException (0xFFFFBD98): Out of memory.
When the file does save, it is ~2.8Mb. Breaking the file up is not an option. I am not looping, this is one shot. I've tried shutting down VS2010 and restarting the computer. It is still inconsistent on saving.
I also had to set the Embed Interop Types to False per guidance from NI. They said that it is unstable in 4.0.
Questions
1. Is there a file limit size to the Save() API function?
2. Is there a workaround to using the Save()?
Best Regards
Solved!
Go to Solution.

I am using C#.NET. I called them in my save method immediately prior to the actual test save sequence.
GC.Collect();
GC.WaitForPendingFinalizers();
GC.Collect();
GC.WaitForPendingFinalizers();
try
       CurrentSequenceFile.Save(outputPath);
       catch (Exceptionerror)
       FireLogEvent(ParserLogType.Parsing_Error, string.Format("{0}", error));
Factory.TSEngine.ReleaseSequenceFileEx(CurrentSequenceFile, ReleaseSeqFileOptions.ReleaseSeqFile_UnloadFile);
Hope this helps

Out of Memory Errors when Exporting Slideshows

Hi -
I've been using LR for sometime now. Today, for the first time ever, I attempted to export a slideshow as a .pdf file, 90% quality setting, 48 slides total. LR created a 41MB file. However, when I played it back, there were many slides which only showed an empty frame with the message "out of memory error" upside down in the lower left corner of the frame. The same slides displayed the message each time I played it, so I'm sure the problem stemmed from creating the file, not showing it.
I have a core 2 duo machine with 4GB Ram and no other applications running at the time I exported the slideshow.
Any thoughts on this? BTW, I'm running version 1.2
Thanks!
E-

Try restarting and reexporting. OOM errors have little to do with how much memory you have or how much is available.

Out of memory errors when trying to sync local and remote sites

We cannot get our remote and local sites synchronized for the first time. We have a huge site and we get out or memory errors or the synch just doesn't work. Any solutions or insights?
Our site has 9,000+ HTML files and accompanying images, pdfs, etc. When we try to synch the remote to the local for the first time, it just will not happen. Every once in a while someone gets lucky, but for the most part, we either get an "out of memory" error or the synch just doesn't work, and it doesn't tell us anything. It just stops responding. HELP!

Hi dmooresatx,
I am not aware of the limitations of the file sizes that are allowed for a successful sync operation. If you are using a purchased version of Dreamweaver CC, send me your Adobe ID along with your contact details (phone, email number). Click on my picture and use the message option. If you are using a team license, get these details from your administrator.
Thanks,
Preran

Get out of memory error when linking Frame doc to RoboHelp project

I just upgraded to TC Suite 5.
Now I'm trying to link FrameMaker files to my RoboHelp project. The FrameMaker files are from a document that was done in Frame 9 (TC Suite 3.5) and now has been converted to Frame 11. It's working fine in Frame 11. No errors when opening any of the files in Frame 11.
I created a new project in RH 11 and tried linking the FM files to it. Some work, but some bring on an Out of Memory message. Interestingly, one file that is 68MB worked fine, one file that's only 58MB brings that message.
I'm going to try using an Externalize Graphics addon that worked well with the old Frame--I can only hope it works with FM 11 now.
Does anyone have any ideas why this is happening, and any solutions besides externalizing the graphics and trying to reduce the file size?
Thanks.

I was finally able to get the files to work by opening and saving in FrameMaker numerous times.
Re: your questions. . . I did not try importing directly. I linked and then generated. Yes, the linking did work with RH9 from the TCS 3.5.

P7n platinum: memory errors when overclocking

Similar Messages

Maybe you are looking for