PCI-GPIB card not found in linux 2.4.22-1.2115.nptl Fedora Core 1

I am trying to install the nigpib driver on a Fedora Core 1 installation of linux (kernel 2.4.22-1.2115.nptl.) The installation script reports the following errors:
Your kernel appears to be configured properly to build NI-GPIB for Linux.
Do you want to proceed? [yn] y
make: `nigpib.o' is up to date.
Copied nigpib.o driver to modules directory /lib/modules/2.4.22-1.2115.nptl/kernel/drivers/char
Devices created.
Probing for PCI-GPIB.
No PCI-GPIB boards detected.
Do you have an AT-GPIB/TNT board installed? [ny] n
/etc/modules.conf is up to date.
Warning: loading /lib/modules/2.4.22-1.2115.nptl/kernel/drivers/char/nigpib.o will taint the kernel: no license
See http://www.tux.org/lkm
l/#export-tainted for information about tainted modules
/lib/modules/2.4.22-1.2115.nptl/kernel/drivers/char/nigpib.o: init_module: Device or resource busy
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/lib/modules/2.4.22-1.2115.nptl/kernel/drivers/char/nigpib.o: insmod /lib/modules/2.4.22-1.2115.nptl/kernel/drivers/char/nigpib.o failed
I have moved the PCI-GPIB card to the first PCI slot with no differences in the error messages I recieve. When I run dmesg I recieve the following information:
unable to get major 31 for gpib
unable to get major 31 for gpib
unable to get major 31 for gpib
unable to get major 31 for gpib
unable to get major 31 for gpib
Any help would be appreciated.

I have this same exact problem. I'd rather not disable USB 2.0, because I use it to transfer files to my MP3 player when in Windows.
I find it hard to "blame the BIOS" when it was working fine under kernel 2.6.7. Anyone know of another solution?
EDIT: Well it isn't the same "exact" problem. When I first boot into Arch, the usb mouse and keyboard don't work. I press and hold the power button on the machine to restart. The second time I boot into Arch, the usb devices do work. If I do a standard soft reboot and go back into Arch, the usb devices again don't work. I guess this is a hotplugging issue, but enabling it in rc.conf does nothing. The only permanent solution I can find is disabling USB 2.0 in the BIOS.

Similar Messages

How do I determine the interrupt detection sequences for an HP 82350A PCI GPIB card?

I am trying to install an HP 82350A PCI GPIB card in CentOS 6.4. I have installed NI-VISA 5.4.
I tinkered around and found driverwizard in /usr/local/bin. It creates an ini file to control the PCI GPIB card.
I had somehow succeeded in detecting the card (PXI3::0::INSTR). My driverwizard output looks like this
[Module]
ModuleName = "PLX PCI <-> IOBus Bridge"
ModuleVendor = "PLX Technology, Inc."
ModelCode = 0x9050
ManufCode = 0x10B5
SubsystemModelCode = 0x10B0
SubsystemManufCode = 0x103C
VISARegistration = Simple
As you can see, it does not have interrupt handling built into it, so I cannot access it properly.
How do I set up interrupt handling for this card? What are the specifications for the following fields?
Interrupt Detection:
Access Type
Access Width
Address Space
Space Offset
Compare Mask
Write/Compare Value
Interrupt Removal:
Access Type
Access Width
Address Space
Space Offset
Compare Mask
Write/Compare Value
Interrupt Disarm:
Access Type
Access Width
Address Space
Space Offset
Compare Mask
Write/Compare Value
This is the first time I have tried hacking at the PCI interrupt level. At the very least, how do I find out the values for the above parameters? Or at best, straight away what are the values for those parameters?

Their IO Libraries Suite supports only Windows. Our lab probably used Windows before. This 82350A card is quite ancient. I need to use this because we also have ancient instruments that do not have Ethernet.

I have problems with pci-gpib card under windows me, What I need to know what to do in order to fix this problems?

Hi, I have installed a pci-gpib card in my computer, I have a problem with
installation, the message of troubleshooting wizard is as follow:
"One or more missing GPIB interfaces.
There are several reasons why you might encounter this problem:
Reason: Your GPIB interface is incorrectly installed.
Solution: Please verify that your GPIB interface is correctly installed
and rerun the NI-488.2 Troubleshooting Wizard.
Reason: You are using a non-Plug-and-Play interface (e.g., AT-GPIB/TNT,
GPIB-PCII/IIA, GPIB-ENET) and you did not use the Add New Hardware Wizard
to add the interface to your system properly.
Solution: Click th
e Add Hardware button and the Add GPIB Hardware wizard
will guide you through the process of adding GPIB hardware.
Reason: For the GPIB-USB and GPIB-1394, the host controller (USB or 1394)
must be working properly in order to use the GPIB interface.
Solution: Click on the System Details button for details about the USB and
1394 host controllers.
Reason: For the PCMCIA-GPIB and PCMCIA-GPIB+, the PCMCIA host controller
must be working properly in order to use the GPIB interface.
Solution: Use the Windows Device Manager to verify that your PCMCIA host
controller is functioning correctly. Start the control panel by selecting
"Start>>Settings>>Control Panel", open the System icon and select the
Device Manager page. If you select "View devices by type", you can look at
the PCMCIA socket properties to ensure it is correctly enabled."
And on system details the message is the next:
"USB Driver type: USB universal host controller"
"This version of windows does not su
pport IEEE 1394."
I am using Windows Me, so i want to know what i need to do to fix this
problems.
Best regards.

If you have a PCI-GPIB card, you needn't worry about the USB port or whether or not Windows ME supports 1394. All you need in NI-488.2 version 1.70 from National Instruments. Install this driver and then insert your card. Windows should detect the card and find the proper driver.
If this did not happen in the proper sequence, look in the device manager and see if the card was installed as an "other device". If this happens, remove the card in the device manager and have windows redetect it. If this is not a solution, you may consider the ask an engineer page at www.ni.com/ask. Provide as many details as possible.

Is there example code for using Ni488 and PCI-GPIB card in non controller mode?

Is there example code for using Ni488 and PCI-GPIB card in non controller mode?

cymrieg,
Your code looks good to me. What is the problem? What happens when it fails? What is the IBSTA value on the controller, and at what point in the code does it stop? What is the IBSTA value on the slave, and at what point does it stop?
One thing is that you might not want to call IBCLR() in a loop on the device. At the beginning of the program is fine...This will send a clear command to the device and will clear out any LACS and TACS bits that might be set. Also your IBDEV call shouldn't be in a loop.
Hope this helps, but let me know if you need more information.
Scott B.
GPIB Software
National Instruments

Symbolic name for PCI-GPIB card

I am using Agilent's ADS2002 to interact with an HP 8722D VNA via a PCI-GPIB card. I need a symbolic name for the card in order to write or read from the instrument; I've tried the suggested GPIB0 and GPIB1, as well as a few other guesses. Nothing on the card looks like a card number or symbolic name. How can I determine what the symbolic name should be? Thanks.

Hello-
Be sure that the GPIB board passes diagnostics. Also, try doing a Scan for Instruments in MAX. It may be that the board is not yet recognized.
Also, consider using a programming language other than ADS. It may be easier for future upgrades to use a language like C or LabVIEW.
Randy Solomonson
Application Engineer
National Instruments

How do I configure my PCI-GPIB cards so that one is a controller and the other is a device being controlled by the first card

I have 2 PC's, both fitted with PCI-GPIB cards. One will be the system controller and the other will be a device on the GPIB bus. How do I configure both cards using LabWindows/CVI v7.0 to achieve this ? What commands are used to send and receive the data ?

Hi Pete,
For the controller board you don't really need to do anything. By default the GPIB interface is configured as controller.
The non-controller can be configured in MAX. Right-click on the interface, uncheck the ono-controller box and change the primary address. It is usually a good idea to set these parameters programatically. Use ibpad to set the primary address and ibrsc to release system control.
For the controller you can use a device descriptor (using ibdev) or a board descriptor (ibfind).
You can only open a reference to the non-controller board using ibfind (ibfind("gpib0"), for example). This will open a board reference. You cannot use a device reference because that implies that the board is capable of addressing the bus. On
ly the system controller can.
Here are some links I found on the web on this subject:
Passing GPIB Control -- System Controller vs. Controller In Charge
Tutorial: Programmatic File Transfers over the GPIB
Example: Using a C Program as a GPIB Non-Controller with LabVIEW as the GPIB Controller
Example: Serial Polling Between Two Computers (Controller and Non-controller)
Hope this helps.
DiegoF
National Instruments.

PCI-GPIB card cannot find instruments in Windows 7

hello, i am new to use Labview to control lab equipments. would be very appreciated any help in advance. Here is my case.
We have two NI PCI-GPIB card in lab. They are working well in old PCs with Windows XP. I installed them to new PC with Windows 7 enterprize edition. Labview version is 2014. The NI-488.2 14.0 and Ni-VISA 14.0.1 is also installed.
when running NI MAX, i could see PCI-GPIB card, so far everthing is fine, no error code. But when i click scan for instruments. there is no result, also no error code message. I borrowed a GPIB-USB-HS controller from another lab. It woks well with the same GPIB cable and equipment. i could see the equipment and communicate. i tried both our PCI-GPIB card and got the same result.
Does someone happen to see the similar problem?
Thank you.
Yutong

Hi thanks for looking into my problem. here is some update.
first, i installed the PCI card to the new PC, it does not work as described above. then, i took it from the PC and installed the GPIB-USB-HS controller. It works well to find our equipment and everything is fine.
second, the oringinal old pc with this PCI card is down, so i used another old pc. this makes problems more complicated. i installed the PCI card on the old PC and it not work. then I connected the USB controller, it works fine. same problem as the new PC.
third, i tried both PCI card. they have the same problem. i think it is unlikely these two cards are both damaged.
I also followed instruction from KnowledgeBase 1UO68A5P: "Scan for Instruments" Fails in Measurement & Automation Explorer. does not improved. the settings of PCI card is shown as attached.
thank you.
Attachments:
old pc.JPG ‏194 KB

PCI-GPIB does not like returning from computer power-save mode. I need to restart the application. Uggh! Customer not happy.

It seems volatile memory is lost on the PCI GPIB Card. When the system returns from power-save, I cannot get to my GPIB instruments. I have to close the application and restart it. I've tried unregistering and reregistering the gpib globals and resetting the device interfaces (reissuing the ibdev command) without luck. I am using Visual Basic 6, but I also get the Measurement and Automation Explorer to fail in the same way, so I don't think it is my development environment.

On Sat, 15 May 2004 20:23:58 -0500 (CDT), SQP Products wrote:
>PCI-GPIB does not like returning from computer power-save mode. I
>need to restart the application. Uggh! Customer not happy.
>
>It seems volatile memory is lost on the PCI GPIB Card. When the
>system returns from power-save, I cannot get to my GPIB instruments.
>I have to close the application and restart it. I've tried
>unregistering and reregistering the gpib globals and resetting the
>device interfaces (reissuing the ibdev command) without luck. I am
>using Visual Basic 6, but I also get the Measurement and Automation
>Explorer to fail in the same way, so I don't think it is my
>development environment.
Can you change your power save settings? What operating system
are you running?
Also, some BIOS's have options for power save. For example, recent
IBM's can be set to maintain power to all peripherals, or only to main
memory. Of course, you would want it to maintain power.
I suspect the GPIB board and its driver are completely unable to
handle power save operation. It probably was never considered while
it was being designed.
Aidan Grey

Configure labview to use agilent 82350B PCI GPIB card

Hi All,
I have just installed a Agilent 82350B PCI GPIB card on my PC, I have up until now been using the NI USB to GPIB adaptor.
How can I configure my LabVIEW settings to be able to use this Agilent interface?
Hope it is a stright forward procudure and that someone can help?
Thanks
Cally.

Have you been to this link on the agilent page?
I found it here
CLA, CLED, CTD,CPI, LabVIEW Champion
Platinum Alliance Partner
Senior Engineer
Using LV 2013, 2012
Don't forget Kudos for Good Answers, and Mark a solution if your problem is solved.

Difference between PCI GPIB card 778-032 and 777158-04

Hi,
A supplier is proposing me a software with a PCI GPIB card 777158-04.
As I already have a PCI GPIB card (reference 778-032), I'd like to know if this one would be suitable. The supplier can't give any guarantee as he hadn't tested this card.
Would could help me finding the difference between these 2 GPIB cards?
Thanks,
Sylvain

I'm not seeing anything for 778-032. Is it an NI card?
There are only two ways to tell somebody thanks: Kudos and Marked Solutions

Computer won't boot with PCI-GPIB card installed

I'm running a windows XP system with Labview 7.1 installed. I have installed the GPIB drivers, but when I insert my PCI-GPIB card, the computer will not boot(it freezes before the POST). I'm running a Shuttle "MK40VN" KM400 Chipset Motherboard.

Well, nevermind, I just verified that the card is in fact fried.

Sim Card Not Found

Each day at random times my phone goes out stating Sim card not found. i was hoping there was a fix in todays update but of course no update. i have been travelling so i cannot back up etc. I have done the reset, the hard reset, and plug into the electric cord, and eventually it does come back but i miss the calls, messages etc. which happen durring this period. What is the fix for this?

If it is an iPhone 4 it is on the side. Bend a paper clip, insert it into the hole, push and the tray will come out. Pay attention to how the microsim is seated and be sure not to bend or damage the tray.

I have unlocked my iphone and when tried to upgrade it, i got an error, so i restored it.But i was not able to activate my iphone 3gs now...it is showing a message like ' sim card not found'..please help me with this regard

I have unlocked my iphone and when tried to upgrade it, i got an error, so i restored it.But i was not able to activate my iphone 3gs now...it is showing a message like ' sim card not found'..please help me with this regard

Try popping out the SIM card and turn off the phone.
Pop in the SIM card once again and turn on the phone, make sure that the SIM card is placed and seated perfectly in the tray!
Tell me how did you unlock your phone!?

Connecting a HP3497A with a NI PCI GPIB card.

Hello, I would like to be able to connect the above mentioned HP product with a NI PCI GPIB card. As I have no prior experience with this equipment, I wanted to know what basic important steps I would have to take to achieve this?

Mbugua,
On the hardware end you'll need a GPIB cable to connect the card with your instrument. On the software side, you'll need the NI-488.2 driver. Please follow this link to download the proper driver version for your OS. I highly recommend that you use LabVIEW 7.0 to communicate with the instrument. If you prefer text-based programming LabWindows/CVI 7.0 would be a great choice. You can check out www.ni.com/idnet to download a library of functions to even further ease communication with t
he HP3497A (currently there is a download designed for CVI).
There are a great deal of manuals available online. Please navigate to www.ni.com and choose "support" to search through them as well as our Knowledge Base.
Please follow the following procedure of installation:
1) Install LabVIEW or LabWindows/CVI (or both)
2) Install NI-488.2 (hardware driver for the PCI-GPIB)
3) Insert the PCI-GPIB into your computer
Regards,
Alan
Applications Engineer
National Instruments

How can I use the instrument toolbox in MATLAB 6.1 to contol the PCI-GPIB card under Linux?

I'm trying to use the PCI-GPIB controller to control lab equipment through MATLAB 6.1 (R12.1) under Linux. MATLAB's instrument toolbox seems to integrate with NI's board, but the MATLAB documentation says it requires the installation of a driver. I've downloaded the linux gpib driver, and I'm able to run the associated utilities (ibconf, ibic, ibsta), but MATLAB cannot interface to it. For example,
>> g=gpib('ni',0,1)
??? Error using ==> gpib/gpib
The specified VENDOR adaptor could not be found.
Where can I find a MATLAB driver and how can I install it?
Thanks,
Richard

Hello-
The knowledge base: "Can Matlab for Windows Call the National Instruments GPIB Driver?" Also applies to this question as well. This article is very extensive. Try searching on ni.com for "+matlab +gpib" for more details.
Randy Solomonson
Application Engineer
National Instruments

PCI-GPIB card not found in linux 2.4.22-1.2115.nptl Fedora Core 1

Similar Messages

Maybe you are looking for