Personal Communicator not working correctly through VPN

Hello Community,
I can use some help please :-)
This client uses Personal Communicator and works fine.
The problem is via IPsec VPN client, they can log in, can make calls, but everybody (all contacts) show offline.
I've been told that they have look at this problem for several weeks now but nobody knows what is going on.... I'm trying right now and having the same problem.
When the remote IPsec client connects it gets the intenal DNS server and everything else works fine (IP communicator and all other applications).
When inside the LAN, all contacts appear online using the Personal Communicator and works perfectly.
I'm sure it's something simple but I have not been able to figue it out.
Appreciate the assistance!
Federico.

Are you using CUPC 7 or 8? What is the VPN concentrator; an ASA?
If 7, all of this is SIP traffic. Use a Wireshark to see what you get. You should see a SUBSCRIBE message for each contact followed by a 200 OK reply and NOTIFY when the person's status changes. Perhaps compare this against a capture from a LAN-attached client to see what's different.
Do you see the ASA's IP addresses anywhere in the layer-seven SIP headers? I sometimes run across SIP inspection occurring on the ASA which is mucking around with the headers by doing things such as replacing the internal CUPS address with the ASA's egress interface address.

Similar Messages

Contacts and Personal Ringtones not working correctly.

I have an iPhone 3G with the latest OS. Since I have upgraded to the latest OS, I have had problems with my contacts when I receive incoming calls. On some of my contacts, I will not see the assigned photo or hear the assigned personal tone, it instead shows the wallpaper and plays the default ringtone. But on other contacts I will see the correct photo and hear the assigned tone. The same contacts are affected by this so it is not randomly changing which contacts are affected. I have checked my sync options and I can see the info in my google contacts and I have completed a hard reset. Nothing I have been able to find in the forums has helped so far. Any ideas?

When your iPhone is plugged into iTunes, go to the Ringtones tab and make sure the radio button is checked that will synch all ringtones. Synch your phone and they should be back.
Hope this helps.

Email pushing not working correctly for office email - 3 seperate devices/carriers

We switched email hosts several months ago and since our email pushing has not worked correctly. Our host/IT guy has been very unwilling to help me through this (I get the pleasure of being the in-house IT source)
I personally am on AT&T have no problems with the other 3 emails I have set up on my blackberry. However I receive my work account one time a day at roughly 6:15. Another user is on Alltel and he receives spotty emails throughout the day, but his gmail account comes through instantly. The third user is on nextel and he receives his 2-3 times per day.
I began to think this was an email host issue since the three of us are all on different carriers, until I found out a fourth user, also on nextel, receives his emails fine.
Users 1-3 are on Outlook 07 on various versions of the Curve. We have all our messages to stay on the server.
User 4 is on the older nextel blackberry push to talk, and is not on outlook.
We do not have an exchange server. Our emails were all set up through our devices.
Any suggestions? The answers I have received through our carriers is to make sure that our messages are set to be left on the server. Everyone else at the office has given up - but for me this is the quest for the Holy Grail.......I'm determined find the answer!
Thank you in advance for any suggestions.
Caitlin Talbot

Potential solution for windows for a side-by-side install. This works for me.
To setup a firefox install side by side so that links from external programs (like email) can open (so you don't get a "Firefox is already running but is not responding" message) do the following.
The solution entails the use of the -no-remote switch. Don't use it for the default browser. Use it for the non default browser.
I'll use firefox 3.6 and firefox 4.0 as examples but this should work for future versions.
+ Install firefox 3.6 and Firefox 4.0 in different directories. Eg.
C:\Program Files\Mozilla Firefox\firefox.exe
C:\Program Files\Mozilla Firefox 4\firefox.exe
+ Open profile manager. Start > Run : firefox.exe -ProfileManager
+ In profile manager create Two Profiles.
firefox3.6
firefox4
+ In profile manager select firefox 4 as your default (assuming you want to default to the latest) and tick "Don't ask at startup"
+ Create two windows shortcuts.
* General: Mozilla Firefox 4 (default). Shortcut > Target: "C:\Program Files\Mozilla Firefox 4\firefox.exe". Shortcut > Start In: "C:\Program Files\Mozilla Firefox 4"
* General: Mozilla Firefox 3.6. Shortcut > Target: "C:\Program Files\Mozilla Firefox\firefox.exe" -p firefox3.6 -no-remote. Shortcut > Start In: "C:\Program Files\Mozilla Firefox"
That's it. Links from external programs should now open in your default browser.
Further details see. [http://kb.mozillazine.org/Opening_a_new_instance_of_your_Mozilla_application_with_another_profile Opening a new instance of your Mozilla application with another profile]

Exchange 2013 - 2007 coexistence - activesync 2007 does not work correctly

Exchange 2013 SP1. On going Saga- Last night we cut over to full co-existence with DNS changes for use of legacy namespace and had to roll back again. We had only two issues but one was considered a show stopper.
The main issue was that Active Sync would not work correctly for 2007 users. It failed the exchange connectivity test and would only work on a device if the domain was entered - or if the legacy namespace was entered manually. That would have meant
chaos for several thousand users so we rolled back. (It worked perfectly for 2013 users).
The error given by the test was "foldersync failed" when I drilled down into the detail. It found autodiscover but failed after the initial handshake. (All other tests passed for 2007 and 2013 users)
We tried:
1. Populating both Autodisover internal and external urls with the legacy namespace
2. Populating only the internal url and leaving the external blank (both 1 and 2 had the same result)
3. Leaving both URLs blank to force 2013 to proxy to the 2007 cas (totally broke it- would not resolve at all)
I don't know if this is related but SSO is failing for 2007 OWA - two prompts.
Environment notes- all internal co-existence is working and the internal LTM F5's are working. Externally we use 2 GTM F5 to the LTM f5's to Ex2013. 2007 has SSL being passed through all the way to the CAS. Servers are split into CAS and MBX over 2 DC's.
Everything else externally was working when we cut over.
any and all help appreciated
Tony

Hi,
Glad to know that you have found the solution.
Thanks for your generous sharing.
Have a nice day : )
Thanks
Mavis
Mavis Huang
TechNet Community Support

PAvilion dv6, fan not working correctly?

Was on my laptop, it shut down randomly, notification popped up saying fan was not working correctly. Is there a way to fix this? Or will it have to be sent away?

Try a can of compressed air in the reverse direction of the normal air flow. You may just have a massive amount of dust on the inside of the heatsink near the fan blades.
Here is a youtube video and about 15min in you can see the fan clearly:
http://www.youtube.com/watch?v=5VMqrudLhJA&feature=player_detailpage#t=1s
Reminder: Please select the "Accept as Solution" button on the post that best answers your question. Also, you may click on the white star in the "Kudos" button for any helpful post to give that person a quick thanks. These feedback tools help keep our community active, so you receive better answers faster.

Sonata font on MacOS - not working correctly

Hi,
I just downloaded and installed the Sonata Standard OpenType file via FontBook in MacOS 10.9.2. So far the font is not working correctly in either MS Word or Apple Keynote -- I get standard qwerty letters rather than musical notation. Anyone ideas on how to fix/troubleshoot?
Thanks!

Hello RKmark,
Thank you for going through the process of using those custom keyboard layouts. It was my pleasure to work on those some years ago.
There is a reason why the placement of some characters on those custom layouts seems arbitrary: They were intended to replace the experience a user would have when using the same PostScript font, which was directly mapped to the characters available on the keyboard. Of course they could be re-arranged today – but that would mean opening a whole different project; and would probably question some of the semantics within Sonata.
Back to your problem:
I just tested the keyboard layout for Sonata, together with the Sonata OTF in InDesign, and I did not find any problems.
Of course this does not help you. So let me just describe what I did:
I copied the OTF file, to ~/Library/Fonts
I copied SonataStd.keylayout to ~/Library/Keyboard Layouts
Admittedly, in OSX Mavericks it is a bit more complicated to install a custom keyboard layout:
In System Preferences, go to Keyboard and Input Sources.
Click the + button at the bottom left, scroll down the list and select “Others”.
In the list to the right, you will find a “SonataStd” keyboard layout, it has a grey icon. Click Add.
After adding this layout, you will be taken back on the Input Sources screen. Check the box next to Show Input in menu in menu bar if it is not yet active.
Back in InDesign, create a new text box, select SonataStd, and choose the SonataStd keyboard layout from the menu bar (marked by the flag of the country representing your keyboard).
Now you can begin typing. I could type the sixteenth-note-rest on a US keyboard with alt-x.
However, one thing I have observed:
If you have set any custom keyboard shortcuts in InDesign that are using the alt-key; they might get in the way of typing some of the symbols.
Which of the available symbols in Sonata are you missing in the custom keyboard layout? I tested them all, and could type everything.
What sometimes happens is that the keyboard layout will switch back to default (US in my case), which then looks like the Sonata keyboard layout is not working.
My personal opinion on this: The keyboard layouts are a nice idea for making glyphs accessible to users that don’t have a glyph palette, but they can be very confusing. They will interfere with the normal usage of the application and OS, since standard keyboard shortcuts will no longer work – simply because they rely on the standard keyboard layout of your system.
Personally, I would use the glyph palette in most cases, simply because switching keyboard layouts back and fort would get to tedious for me.
I hope this helps, let me know if you have any further questions.

1st Gen iPod touch not working correctly?

I have a 1st generation 8GB iPod Touch. It's not working correctly.
My biggest problem is that, unexplaiably, certain areas of the screen don't seem to register touch anymore. There is a sort of "L" shape on the left and bottom edges of the screen that won't register touch, making it impossible to move applications to the previous page on the home screen and making it hard to use the keyboard/buttons while in portrait mode. It's extremely frustrating to try to change the volume while playing a song, as I now have to either put the iPod in sleep mode then double tap the home button or flip it to cover flow and double tap the home button to do it.
http://i38.photobucket.com/albums/e140/Vipershark/IMG_0001.png
(Highlight the image to see it better.)
This is a screenshot of the working/non-working areas that I made using the Whiteboard application. The white area that you see (excluding the little half circles of black which are extended brush strokes and not actually working areas) is the area that doesn't work. I can't seem to figure out why it happened, as I've never dropped or otherwise damaged it. It just happened one day, and I don't know why.
But I can't fix it. I've tried everything. Upgrading (I'm now running iPhone OS 3.0 which still didn't fix the problem.) didn't work, restoring didn't work, deleting everything and restoring from factory settings didn't work.
I'm also having a few other problems as well, though they're not as bad. My home button seems to stop working sometimes and sometimes the entire screen witll stop registering touch until I put the iPod to sleep and turn it back on. It also seems to go a lot slower than usual.
My iPod is less than a year old. Can you help?

Vipershark,
I had a very similar problem this past weekend with my 1G 8GB iPod touch. But with me, just the left side of the screen wasn't registering my touch. I could still access the bottom section, which you cannot.
The good news for me is that I fixed it and I hope it works for you as well. What fixed it for me was resetting all my settings. To do this, go to the settings icon, then click on general, and then on the very bottom is reset. Choose "reset all settings."
Apparently this is different than a restore through iTunes, which you tried. I also tried that earlier and it did not help.
Of course, the reset solution I used relies on you being able to access all of the correct buttons, so I hope you can!
Please let us know if this works for you. If not, since it is less than a year old, it is still under warranty. Contact Apple and see what they can do.

Share point in server admin not working correctly... I think

I suspect that the share point in server admin is not working correctly. In workgroup manager when I click on a user and then click on the "home" tab, under the full path field I see a file path of:
afp://server.mydomain.com/Users
However if I go to Server Admin -> AFP -> Share Points then click on the Users share and then click on the share point tab below, enable auto mount is disabled. How can this be possible? I thought for a directory to show up in home in workgroup manager it had to be set as an auto mount. Has something possibly corrupted? And what?

Here's a bit more information about our setup and our experiences with Apple's CUPS implementation:
On the server, all printer queues are set up with only lpr and ipp sharing enabled with the PPD setting for each printer set to Generic Postscript. We found that setting the PPD to the printer specific one on the server caused problems when clients tried to use printer specific options, like paper tray selection, etc.. The selection would be undone, apparently because the driver on the server would override the previous settings. Using Generic Postscript allows the client PPD settings to go through unmodified. Our printers are general a mix of HP LaserJets and some Sharp Copiers.
All clients use lpd to the server queues with the printers' actual PPDs configured. Using ipp is superior in that printer feedback (jams, out of toner, etc) makes it back to the clients, but ipp only works when the client, the server, and the printer are on the same network. If the ipp client is not on the same network, the client spooler immediately goes into a paused state and the print job is stuck on the client.
Using lpd to the server queues works reliably, but there is no feedback to the client. Jobs disappear from the client queue and go to the server, appearing to the user as a successful print. If the printer is down, there's nothing they can see or do about it.

System Update not working correctly

Hi forum,
System Update (Version 4.00.0024) is not working correctly on my T500 with Windows 7.
1: Not detecting old versions
SU is not detecting, that there is an old version of Access Connection (5.42) installed although there is a new version 5.50 avaliable. I had to do a manual update.
2: Not installing a suggested update
Each time I run SU, I get a suggested update for "Fix for Issue of HDD with HDP Detection for Windows Vista/7". After downloading there comes a meaningless message "package was not installed" (Paket wurde nicht installiert). No hint for any error.
3: Some drivers (e.g. for the ultranav) have not been downloaded at all - I had to test the functions of some hardware components and download the appropriate drivers manually in case of malfuncion.
Probably there is a solution known within the forum community, at least this should be a message to lenovo (I received no response from the help desk when reporting this finding).
Regards
AH_DE

Dear Herik,
thanks for your answer.
I checked the log file and found thousands of entries. Here are the lines related to "Fix for ...".
Info    2010-02-03 , 08:40:37
          bei Tvsu.Gui.CustomComponents.UpdatePanel.SynchronizeBoxPackage(Object sender, EventArgs args)
          Message: Selected to install: Fix for Issue of HDD with HDP Detection for Windows Vista/7, with
Info    2010-02-03 , 08:40:43
          bei Tvsu.Coreq.LoadCoreqsProcessor.ProcessUpdatesImplementation(Update[] ups)
          Message: Candidate list:
Fix for Issue of HDD with HDP Detection for Windows Vista/7[reboot type 3]
Info    2010-02-03 , 08:40:57
          bei Tvsu.GenericPackageInstaller.GenericPackageInstaller.ExtractFiles(String extractCommand)
          Message: osfq03ww.exe -s -ex -fC:\SWTOOLS\OSFIXES Extract command was executed sucessfully in Fix for Issue of HDD with HDP Detection for Windows Vista/7 update
Info    2010-02-03 , 08:40:57
          bei Tvsu.GenericPackageInstaller.CmdInstaller.InstallUpdate()
          Message: Update Fix for Issue of HDD with HDP Detection for Windows Vista/7 is being install using Windows Service
Info    2010-02-03 , 08:40:57
          bei Tvsu.Engine.Process.PackageInstallerProcess.InstallNewUpdates()
          Message: Update Fix for Issue of HDD with HDP Detection for Windows Vista/7 installation failed
ADDITIONAL ENTRIES
Info    2010-02-03 , 08:40:57
          bei Tvsu.Gui.FlowScreens.Results.AdjustComponent()
          Message: System updated:
          Installed=0
          Not Installed=Tvsu.Beans.Update[]
          Deferred=0
          Download Failed=0
          Hidden=0
Severe          2010-02-03 , 08:41:17
          bei Tvsu.Sdk.SuSdk.ShutDownApplication()
          Message: Has happened an exception while the UNCAuthenticator.Shutdown() was executedShare name can not be null or empty
Since I'm a normal user only, I can't interprete this information. Do you know what to do?
Kind Regards
AH_DE

Query is not working correctly

Hi all,
Below query is not working correctly. Please let me know, if you find the mistake
select
a.name,
b.VOD_NAME,
count(xm.ATTRIB_03)
from
siebel.s_vod b
left outer join ISS_OBJ_DEF c on b.OBJECT_NUM=c.PAR_VOD_ID
left outer join vod d on c.VOD_ID=d.row_id
left outer join PROD_INT a on d.OBJECT_NUM=a.CFG_MODEL_ID
left outer join PROD_INT_XM xm on a.row_id=xm.PAR_ROW_ID
where
b.VOD_TYPE_CD='CLASS_DEF'
and
c.LAST_VERS = 0
and
b.vod_name='Componentes'
group by a.name,b.vod_name having count(xm.ATTRIB_03) >=5

user9522927 wrote:
Hi all,
Below query is not working correctly. Please let me know, if you find the mistake
select
a.name,
b.VOD_NAME,
count(xm.ATTRIB_03)
from
siebel.s_vod b
left outer join ISS_OBJ_DEF c on b.OBJECT_NUM=c.PAR_VOD_ID
left outer join vod d on c.VOD_ID=d.row_id
left outer join PROD_INT a on d.OBJECT_NUM=a.CFG_MODEL_ID
left outer join PROD_INT_XM xm on a.row_id=xm.PAR_ROW_ID
where
b.VOD_TYPE_CD='CLASS_DEF'
and
c.LAST_VERS = 0
and
b.vod_name='Componentes'
group by a.name,b.vod_name having count(xm.ATTRIB_03) >=5I couldn't see through the internet what happend when you ran said query. How about helping us out by showing us the evidence that it "is not working correctly".
"Here's a picture of my car sitting in the driveway. Why won't it start?"

Internet Explorer 11 "Enterprise Mode" do not work or do not work correctly!

Dear community,
Since yesterday we test the Feature "Enterprise Mode" for "Internet Explorer 11". However, we have many problems
with this Feature. We have configured it as described by officially instruction by MS, but it does not work
properly. Here is what we have done exactly to test this Feature:
In Registry Key " HKEY_LOCAL_MACHINE \ Software \ Policies \ Microsoft \ Internet Explorer \ Main \ Enterprise Mode " we have created the Entry " Site List " and create the string " Enable" . In the
String "Enable" we have added no value .
In Case of String "Site List" , we have specified the path to the XML file , as value of this String.
The XML file was created with the Site List Manager from Microsoft
And now, we regocnized following Problems:
The "Enterprise Mode" ist only "active", if the User(!) check "Enterprise Mode" under "Tools"...!
The site list is seemingly ignored, although in the Registry "currentversion" is pulled correctly, everytime we change
the XML File. So we think "SiteList" is configured well.
On one of our test computer freezes Internet Explorer 11 , if you try to hook the corporate mode
In Summary, it seems to be configured properly but it even do not work or not work correctly.
Our goal would be:
Enterprise Mode + access to the Site List by IE11 should be "on" by Default!
Entrys of sitelist.XML should be filtered and shown in "Enterprise Mode" or/and the right "DocMode", as configured.
The user should have no chance to check on or off the"enterprise mode"
We use "Windows 7" on all our Clients, as test Clients are also running the same operating System...
Please reply
Thank you very much
Greetings!
Ps: Please do not be angry if pronunciation or grammar do not fit well. English is not my nature language (my nature language is german)

Hi，
According to your description, seems the end-users can manually turn on\off the enterprise mode, If you don''t want this, you can disable the option.
Computer(User) Configuration > Administrative Templates > Windows Components > Internet Explorer\Let users turn on and use Enterprise Mode from the Tools menu option
Disable this option, user will not have "Enterprise Mode" under "Tools", after that, please run gpupdate /force to update the policy, and get "Use the Enterprise Mode IE website list" applied again in the target system.
After that, the enterprise mode website list get applied again, and user don't have an option to disable it.
Yolanda Zhu
TechNet Community Support

10.9.2 Mail not working correctly

I'm the only person in the office to upgrade to 10.9.2 (thankfully!). Since then, Mail has not worked correctly. It is an IMAP account.
When I click on an existing message in my inbox, instead of displaying instantly it takes 3-4 seconds. The screen scrolls light grey, dark grey, light grey, dark grey then the message. I can live with this but it's very annoying.
But worse, I now cannot perform any mail searches to refer back to existing messages I have in any of my mailboxes. Search functions 'to, 'from' 'entire message', 'any' do not work. Even if the message or sender is in the inbox, it can’t find it. This is serious as I'm constantly using this function.
Many thanks if you can help.
Simon

My wife is having the exact same problem all of a sudden with gmail on her MacBook Air. Also running 10.9.2. Everything is running perfectly on the iPhone, but on the Mac, no new email is downloading and the inbox is not syncing.
Hoping someone can help. Thanks!

Line-in input not working correctly in Garageband

Problem:
Line-in input not working correctly with Garageband. Problem occurred AFTER installing and using Blue Yeti USB mic, purchased from the Apple store.
System Details:
'07 20" iMac 2.4GHz 4GB RAM, OSX 10.6.5, Garageband '11 v6.0, Logitech Z4 speakers.
Background:
Before using the Yeti USB mic, I used the line-in jack. I'd connect a Shure mic or guitars directly in, but more recently through a 12 channel mixer. Have connected the Shure mic directly into the input jack, and the computer appears to be picking it up (System Preferences->Sound->Input), it is responding correctly there. Have set the output to the headphone (line-out) jack. When I go into Garageband, I can select from Line-in 1, Line-in 2, and Line-in Stereo. The trouble is that it's the iMac's built-in mic that is active (the one above the screen), not the line-in. I've rebooted the computer, checked the connections, reconnected the Yeti mic and I can't find what's causing the problem. Not sure what to do from here, need some help. Thanks

I have Logic Express on the iMac as well and I worked out how to set the input device back to the Line-In. I went back to Garageband and found the equivalent setting under Preferences->Audio/MIDI. Thanks for reading, sorry I didn't sort it out sooner! Merry Christmas!

Sleep not working correctly

Since updating my Late 2010 iMac to Moutain Lion the sleep function does not work correctly. They system keep waking up for no reason. The monitor comes comes day or night. I cannot figure out a fix or work around. Any ideas?

Please read this whole message before doing anything. This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it. Step 1 The purpose of this step is to determine whether the problem is localized to your user account. Enable guest logins* and log in as Guest. For instructions, launch the System Preferences application, select Help from the menu bar, and enter “Set up guest users” (without the quotes) in the search box. Don't use the Safari-only “Guest User” login created by “Find My Mac.” While logged in as Guest, you won’t have access to any of your personal files or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin. Test while logged in as Guest. Same problem(s)? After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it. *Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing. Step 2 The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login. Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs. The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. *Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Test while in safe mode. Same problem(s)? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of steps 1 and 2.

Bootcamp not Working Correctly on Macbook Pro

Hello,
I am trying to install Windows 7 or 8 onto my Macbook Pro with Bootcamp.
Once I have opened the Bootcamp program it all works fine and I can go through the steps perfectly, it will appear to partition the HDD correctly and it will recognise the Windows install DVD correctly.
However, once my Macbook Pro restarts at the end of the process it boots up and the screen stays white, nothing happens and since I have a gaming keyboard and mouse the lights light up on it for about 5 seconds when it restarts then they go off (Off meaning they aren't powered). The screen will stay white for aslong as I can tell, I left it for 3 hours and the screen was still white.
So I thought there may be a problem with how it selects the the startup disk, so I boot it up into disk utility then select the DVD again and it stays white, again.
Anyone know why this is not working correctly? I have tired this with mutliple install DVD's whether they be Windows 8 or Windows 7. I also do not want to use a program that creates a virtual machine, I would like to run Windows 7 to the full so that I can play games with the maximum amount of FPS.
If you have any questions do not hesitate to let me know.
Thank you for your time.
Best Regards,
Kieran J.

Does it now work only on battery? or using the power supply?
If only on the power supply use a grounded plug.
Otherwise try reseating touchpad cable. Post the size and year of your MBP.

Personal Communicator not working correctly through VPN

Similar Messages

Maybe you are looking for