Photosmart 5510 printer model #B111A when using touchscreen apps i cannot connect to the server
Photosmart 5510 all-in-one printer, model #B111A, windows XP----i can print from the computer, but when i try to use the apps on the touchscreen i get a message error "cannot connect to the computer"
The steps below typically resolve the issue you’re experiencing:
1. Unplug the power cord from the back of the printer.
2. Unplug the power cord from the back of your router (and modem, if separate from the router).
3. Wait 20 seconds, then plug the router (and modem, if applicable) back in.
4. Wait 30 seconds, then plug the printer back in and power it on.
5. Press the ePrint button on the printer's front panel, and it should try to connect to Web Services again.
Those steps usually resolve the issue, but if it still occurs you can try setting static network info for the printer (which sometimes helps to stabilize the printer's ability to get outside of your network, to the internet):
1. Press the wireless icon at the top of the printer's screen and note the IP address.
2. Enter the IP address into the address bar of a web browser on a computer and press enter or click the browser's go button.
3. The printer status page should be opened. Click on Network at the top.
4. Click on Networking on the left.
5. Select Proxy Settings.
Note: If you are prompted for a redirect, select OK. If you receive a certificate warning, select the option that lets you continue anyway.
If you receive a Internal System Error, refresh the page until it loads the proxy settings.
6. Verify that all fields are blank. If they are not, clear them and make sure the Proxy Server requires authentication is unchecked and click apply. You should get a success message.
7. Click on Network Address (IP) on the left.
Note: If you only see IP Address Configuration and DNS Address Configuration with a yellow note, refresh the page until it loads completely.
8. Leave the IP Address Configuration as Automatic IP.
9. Change DNS Address Configuration to Manual DNS server.
10. Enter 8.8.8.8 for the Manual Preferred DNS Server and 8.8.4.4 for the Manual Alternate DNS Server.
11. Click Apply and you should get a success message.
12. Power off the printer for 30 seconds and then turn it back on to force the new settings to take effect.
If I have SOLVED your issue, please feel free to provide KUDOS and make sure you mark this thread as SOLUTION PROVIDED!
Although I work for HP, my posts and replies are my own opinion and not those of HP.
Similar Messages
-
LATELY HAVING A PROBLEM FORWARDING EMAIL VIA GOGGLE FROM FOX NEWS ARTICLES, WHEN I CLICK ON GOGGLE I SEE SAFARI CANNOT CONNECT WITH SERVER.
HAVE TRIED DELETING CACHE AND COOKIE, HISTORY AND RESETTING SAFARI WITH NO SUCCESS.
ANY HELP YOU CAN GIVE ME TO RESOLVE THIS ISSUE WOULD BE GREATING APPRECIATED.
THIS IS MY FIRST TIME USING THIS FORUM, NEW AT THE COMPUTER WORLD.
HOPE YOU'LL BE ABLE TO HELP ME RESOLVE THIS PROBLEM.
THANK YOU!It isn't Goggle. Did you make sure you went to Google?
-
I am using a mac... Have downloaded new version. Is all I need to do to Drag Firefox from Applications to trash to uninstall? Do I still need to also delete Program Folder? If so, where can I find it?
If there are problems with updating or with the permissions then easiest is to download the full version and trash the currently installed version to do a clean install of the new version.
Download a new copy of the Firefox program and save the disk image (dmg) file to the desktop
*Firefox 16.0.2: http://www.mozilla.org/en-US/firefox/all.html
*Trash the current Firefox application (e.g. open the Applications folder in the Finder and drag the Firefox application to the Trash) to do a clean (re-)install
*Install the new version that you have downloaded
*https://support.mozilla.org/kb/Installing+Firefox+on+Mac
Your profile data is stored elsewhere in the Firefox Profile Folder, so you won't lose your bookmarks and other personal data if you uninstall and (re)install Firefox.
*http://kb.mozillazine.org/Profile_folder_-_Firefox -
HP Photosmart 5510 B111a - Cannot connect to the server
My printer is not printing when I email [id] @ hpeprint.com, even though I get the "ePrint Job Received" email, so I investigated it further.
It's on the network because I can access the web page like normal.
Here's what I'm greeted with.
There's a red cross next to the "ePrint", but the network has a green tick. Odd.
I check the "web services" tab...
Again, it shows a red cross and says "fix this".
I click "fix this", which after a little while displays this.
The error says:
Cannot connect to the server.
Check the Internet connection and try again. Or contact your system administrator or the person who set up the printer.
If your network requires a proxy server address to connect to Internet, click Enter Proxy or check your browser settings.
I know my connection is working as it should be.
I believe the fault lies in the printer, please can you advise further.
Thanks.I discovered the problem.
I recall the printer had advised me some weeks ago to automatically set a manual IP.
When this was done it seems to turn off DNS settings so it cannot resolve any hostnames and will not access any services even though it is connected to the network.
I restored the IP back to automatic, which allowed me to also set DNS to automatically.
It seems that if you set a manual IP address on the printer, you cannot set the DNS.
Odd behaviour. -
When trying to access i tunes store when in I Tunes i cannot connect to the internet - any thoughts? i have tried un-installing and re-installing but no joy
Close your iTunes,
Go to command Prompt -
(Win 7/Vista) - START/ALL PROGRAMS/ACCESSORIES, right mouse click "Command Prompt", choose "Run as Administrator".
(Win XP SP2 n above) - START/ALL PROGRAMS/ACCESSORIES/Command Prompt
In the "Command Prompt" screen, type in
netsh winsock reset
Hit "ENTER" key
Restart your computer.
If you do get a prompt after restart windows to remap LSP, just click NO.
Now launch your iTunes and see if it is working now.
If you are still having these type of problems after trying the winsock reset, refer to this article to identify which software in your system is inserting LSP:
iTunes 10.5 for Windows: May see performance issues and blank iTunes Store
http://support.apple.com/kb/TS4123?viewlocale=en_US -
See the title
I keep getting the message "mail cannot connect to the server…." when it clearly can and does. How do I prevent these messages from appearing?
helpOn your iPad or a Mac?
You posted in the iMac community but your profile indicates an iPad 2. -
I am trying to connect my iPhone to the cloud but when it asks me to agree to the new terms and conditions I click agree andI get a message stating it cannot connect to the server.
Apple servers are currently down at the moment. Try back later or wait until Apple resolves the issue.
-
Printer cannot connect to the server
I am going bonkers! For no reason that I can fathom my printer does not connect to the server (i.e. my PC). I have downloaded the latest drivers. I have uninstalled and re-installed. I have run the HP Doctor. The printer finds my router ok and has been set up correctly. The same problem exists with my laptop. I have windows 8.1 and HP Officejet 6600. I am at my wits end. It has worked and nothing has changed. I have run a strict anti-virus checker too. Does anyone out there have a clue as to what is going on? I will be so grateful for your help. Oh yes when I logged on to the HP site and live chat I was told my printer was out of warranty - it is only a month old! So no help there.
doghaus,
Change your preferred DNS server to 8.8.8.8 and your alternate to 8.8.4.4.
Let me know if that works for you.
-------------How do I give Kudos? | How do I mark a post as Solved? -------------------------------------------------------- -
I am abroad for the summer and there is no internet available. I purchased a hotspot in a nearby vodaphone and they helped me connect the Ipad to the hotspot. I assumed I would have no trouble after that. Once I got home though and connected to the hotspot i found i could not open the internet without getting a notice about not connecting to the server. I have a signal and can connect to the hotspot and yet i get no internet. I already spent 50 euro on the hotspot for 2 months of wifi...is there a way to actually fix the problem without me having to spend more money?
I'm guessing e mail does not work either. While the pad is seeing the network, it is not yet connecting, probably trying to work through your security set up. I suggest you go to settings, then network, then the details of the network. Do you see an ip address that starts with 192.168.1. Then some number? If not, the router has not made friends with the pad.
Suggest that from that same screen, you select 'forget this network'. Then start over again, paying close attention to what happens when you provide the security password. -
Can't setup the Web Services as printer says "cannot connect to the server to get the update"
Just purchased and am setting up my HP Officejet pro 8600. It has set-up wirelessly without a hitch until I tried to install/enable the web services and I continue to get a message saying "the printer could not connect to the server" therefore it cannot check for an update on Web Services apps and they will not be enabled. Never had so much trouble setting up an HP printer in the past. Looks like this web services is more of a headache and a gimmick to sell this printer.
Hi Guys,
I found the solution after 2 days.
Open internet explorer and type in the IP address of the printer in the address bar then press enter.
The embedded web server of the printer should pull up.
C. Click the network tab near the top.
On the left side, click IPv4 under your connection type, wireless or wired.
D. Change the IP address from automatic to manual.
Enter the same IP address, default gateway, and subnet mask.
Enter 8.8.8.8 for the primary dns and 8.8.4.4 for the secondary then click apply.
E. After the apply button has been clicked to apply the static IP settings, enable Web Services.
Good luck -
Photosmart C6150 printing slow even when using printer controls
It started out intermintently printing slow using the PC and the front panel copy button, as if it was switching into high resolution mode. I checked the driver / printer prefrences and found nothing in high resolution mode. Recently we have been doing alot of copying from the front panel, not from the computer software, and it got worse. I checked the quality setting in the printer and even set it to fast. It would then print a semi-fast sheet (as if it was fighting itself to print faster but couldn't), then a fast sheet, then the next sheet would be slow again. After a few times of doing this, it finally stopped printing normal or fast and now it's stuck in high res slow printing mode. I printed a self test diagnostic page and it printed in less than 60 seconds and showed nothing. I have also chaned out the drivers on the PC and still nothing. Could it be a firmware issue and is that something I can flash?
Hello , Welcome to the HP Community. I hope you have a pleasant experience here. I understand you are having an issue with slow printing on your HP Photosmart C6150 All-in-One printer. I'd love to help you with this. First, I'd like you to try printing a self test page again: HP Photosmart C6100 All-in-One Series - Printing the Self-Test Diagnostic Page If the test page printed in less than 60 seconds, then I would suggest following the steps here to troubleshoot the driver and settings on your computer:HP All-in-One Printers - Slow Printing in Windows: Computer Issues If the issue persists after these steps, I'd recommend replacing your USB cable (with a smaller one if it is over 6ft long). If the test page took longer that 60 seconds to print, then I would suggest following the steps here to troubleshoot an issue you may be having with the printer hardware:HP All-in-One Printers - Slow Printing in Windows: Hardware Issues Another thing I would suggest, if the printer is slow even from the printer, would be to make sure the printer is plugged directly into a wall outlet. The printer does have a power moderator built in, so when plugged into a power surge or battery backup, it can often not get enough power. Please respond to let me know if these steps help to resolve your issue!Have a great day.
-
Error regarding server connection problems when trying to download rented film on my ipad
Remember, any purchased item from the itunes store is forever associated with the Apple ID used to buy it. So when you get prompted for an ID/password and it doesn't accept it, then you are using the wrong ID.
Go to Settings>iTunes and App Stores, be sure it's logged into the ID you have set on the iphone (since that one seems to be connecting with the right ID). If you've done this, then you might wait a bit to see if the "cannot connect to .. store" message has to do with internet connections. -
Printer cannot connect to the server when "checking for update". Can't setup eprint.
I have an Officejet 4620 All-in-one working wireless. It prints, scans and sends and receives faxes well. After setting up a fixed IP address, I started to get this problem. I test the wireless connection pressing the wireless button and report says everthing's fine. I'm using Windows 7 64 bit SP1.
This is how I configured IPv4:
IP Address 10.0.0.250
Subnet Mask 255.255.255.0
Default Gateway 10.0.0.67
Preferred DNS Address 10.0.0.67
Alternate DNS Address
WINS Server 0.0.0.0
Secondary WINS Server 0.0.0.0doghaus,
Change your preferred DNS server to 8.8.8.8 and your alternate to 8.8.4.4.
Let me know if that works for you.
-------------How do I give Kudos? | How do I mark a post as Solved? -------------------------------------------------------- -
When using my ipod, i get an error message cannot connect to the server
I have an ipad 2 and Ipod touch 4th gen. Safari works fine on the ipad but occassionally, I get an error message of "cannot connect to server" on the ipod when I use safari. But the ipad still can connect with NO problem. Can someone explain why this happens and how to fix it?
ThanksSaw this on another post.
Applecare Senior Advisor Txx Bxxx (I have his contact info in an email he just sent) just confirmed with me that the problem people are having with the App Store not loading is an apple issue with there servers, ITS NOT YOUR IPAD so don't go restoring it! It's not happening to everyone however but they are looking into it, its really hit or miss.
In the meantime ...........
The Complete Guide to Using the iTunes Store
http://www.ilounge.com/index.php/articles/comments/the-complete-guide-to-using-t he-itunes-store/
Can't connect to the iTunes Store
http://support.apple.com/kb/TS1368
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/kb/TS3297
Best Fixes for ‘Cannot Connect to iTunes Store’ Errors
http://ipadinsight.com/ipad-tips-tricks/best-fixes-for-cannot-connect-to-itunes- store-errors/
Try this first - Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
This works for some users. Not sure why.
Go to Settings>General>Date and Time> Set Automatically>Off. Set the date ahead by about a year.Then see if you can connect to the store.
Cheers, Tom -
I am having difficulty with icloud on my ipod. It is working well with my MacPro and Iphone 5 but when it asks me to agree to terms and conditions , message is that it cannot connect to server.
Welcome to the Apple community Linda.
Have you tried deleting the account! restarting the device and trying again.
Maybe you are looking for
-
Recently moved to a new PC. Upon installing iTunes, in the Settings dialogue, I've indicated where my iTunes library is stored. And yet, all of my albums in iTunes are showing up with the "cloud" icon, meaning that the client doesn't realize there
-
Does anyone know if the SATA drivers offered for download will work (properly) with the 64 bit versions of XP and Win 2k3 server? I want to go ahead and at least put the 64 bit XP (Extended Systems) on there, but I don't want to waste my time if it w
-
Best Practices: Flash Player 10.1 and Flash Lite 4
I've found the documentation for Flash Lite 4. It appears to support most everything you'd want to do in AS3, aside from some desktop-specific APIs like Clipboard, File, ContextualMenu, etc.. I've also noticed that there's a Flash Lite 4 compile tar
-
I lost my hard-drive to laptop in fall '06. I-Pod library went w/it. I was able to get help to get the Library downloaded to new computer... all songs show up using "Manual load" directions. Now- I can't get new songs to load. it's like it's created
-
InterMedia in Jdeveloper?
How can i use interMedia possibilities in Jdeveloper. I want to get an image, audio, video from a oracle8i database. null