Physical interface Default Gateway connecting VPN with AnyConnect

When I connect vpn with AnyConnect, I can't see default gateway on Physical Interface.
before connect vpn
==========================================
C:\WINDOWS\system32>ipconfig
Windows IP Configuration
Ethernet adapter Local Area
        Connection-specific DNS Suffix . :
        IP Address. . . . . . . . . . . . : 10.1.1.100
        Subnet Mask . . . . . . . . . . . : 255.255.255.0
        Default Gateway . . . . . . . . . : 10.1.1.10
after connect vpn with anyconnect
==========================================
C:\WINDOWS\system32>
C:\WINDOWS\system32>ipconfig
Windows IP Configuration
Ethernet adapter Local Area
        Connection-specific DNS Suffix . :
        IP Address. . . . . . . . . . . . : 10.1.1.100
        Subnet Mask . . . . . . . . . . . : 255.255.255.0
        Default Gateway . . . . . . . . . :'Can't see default gateway'
Is this the specification of Anyconnect?

Nyanko,
This will happen when you are using tunnel all as the split tunneling policy, the computer will encrypt all the traffic so the default gateway will be removed from the physical connection and placed into the virtual adapter. If you take a look at the routing table you will see that what really happens is that the original default route's metric will be changed so that it is higher than the one injected by the virtual adapter, once you disconnect it should go back to normal.
Further information on split tunneling:
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080975e83.shtml
HTH
Jonnathan

Similar Messages

Vpn-framed-ip-address not working with anyconnect

Hi Folks, please help me to verify if this case is a bug or a "not valid scenario".
Scenario:
ASA 5520, OS 9.1, SSL VPN with Anyconnect v3.x, static ip address for the client, and RSA token authentication (all the users/pin/passwords are in the RSA server, not in the ASA, but i need to create some users in the ASA in order to apply the vpn-framed-ip-address attribute for specific users).
In fact the anyconnect ssl vpn with RSA auth works fine, the ssl connection works, the user is authenticated, the anyconnect works, traffic passing, BUT.. the anyconnect its getting an ip address from the ip local pool INSTEAD of the static ip defined with the vpn-framed-ip-address command.
I'm trying to assign a static ip address for a user (defined locally on the ASA) that performs auth via RSA (aaa-server), by using the vpn-framed-ip-address command as an attribute for this local user. But it seems the command is not working.
Already I´ve tried to resolve (with no success) by entering the
no vpn-addr-assign aaa
no vpn-addr-assign dhcp
vpn-addr-assign local
Also i´ve tried by removing the pool from tunnel-group in order to force all the connection session to use the static ip address, but in this case, the anyconnect sends a message "No Address Available for SVC Connection". Meaning the ASA simply is ignoring the vpn-framed-ip-address command.
Its supposed the ASA implement the policies in this order, DAP > User policy > UserGrp policy > ConnProfile > DefGrpPolicy, and according to this, the vpn-framed-ip-address command should take effect first since its specified as User policy, overriding everything else. But its not working.
At this point i think the issue is... since the user is locally defined but its password its being authenticated via RSA (not local), the user attributes (static ip) are being ignored by the ASA because its not expecting to receive an ip address from the aaa server (RSA), so jumps to the next policies falling to the pool. Anyway the user policies attributes SHOULD work according to cisco.
Please your advise, or tell if its a bug? or a not valid scenario for this command to work with the ASA.
This is the current config:
ip local pool PoolSSL 192.168.229.10-192.168.229.19 mask 255.255.255.0
aaa-server RSA protocol sdi
aaa-server RSA (inside) host 192.168.12.1
retry-interval 5
no vpn-addr-assign aaa
no vpn-addr-assign dhcp
group-policy GroupPolicyABC internal
group-policy GroupPolicyABC attributes
wins-server none
dns-server value 192.168.61.1 192.168.61.2
vpn-tunnel-protocol ssl-client
group-lock value TunnelGroupABC
split-tunnel-policy tunnelspecified
split-tunnel-network-list value ServersDB
default-domain value my.domain.com
split-tunnel-all-dns disable
webvpn
anyconnect ask none default anyconnect
username USER1 password xHhacRZ56Uadqoq encrypted
username USER1 attributes
vpn-framed-ip-address 192.168.229.7 255.255.255.0
group-lock value TunnelGroupABC
tunnel-group TunnelGroupABC type remote-access
tunnel-group TunnelGroupABC general-attributes
address-pool PoolSSL
authentication-server-group RSA
default-group-policy GroupPolicyABC
tunnel-group TunnelGroupABC webvpn-attributes
group-alias AccessToDB enable
I´ll wait for your answers, regards!

https://tools.cisco.com/bugsearch/bug/CSCtf71671/
you need AAA assignment, or at least you needed to have it a couple of years back.

Configure a default gateway on an AP in CLI

Hi everybody,
I have gone through Cisco IOS Commands Master List, but I can't find the command line for assigning an IP default gateway on AP1130AG with IOS 12.3(8).
May you please help me ?
Thanks in advance !

It was actually very easy : need to enter it like it appears in the config.txt file.
In "configure terminal" mode :
ip default-gateway AAA.BBB.CCC.DDD
They probably omit to put it in the IOS Commands Master List.

Default Gateway when connected to VPN

Thanks for reading!
This is probably a dump question so bear with me...
I have set up a VPN connection with a Cisco ASA 5505 fronting internet, with the customers environment behind it (on the same subnet), When connected ot the VPN I can reach the inside Router fronting me and one switch behind the Router (every switch is connected to the router), but nothing else.
My beet is that the Router is messing with my connection, but,, nevermind that!, the setup ain't complete anyway... my question is more related to the Gateway I'm missing when I'm, from the outside, is connected to the VPN on the ASA, could this mess it up? Shouldn't I have a Standard-Gateway in the ipconfig settings in windows?
This is who it looks like now:
        Anslutningsspecifika DNS-suffix . : VPNOFFICE
        IP-adress . . . . . . . . . . . . : 10.10.10.1
        Nätmask . . . . . . . . . . . . . : 255.255.255.0
        Standard-gateway . . . . . . . . :
The internal network is :
172.16.12.0 255.255.255.0
Below is my config for the ASA, thanks a lot!!!!!!!
!FlASH PÅ ROUTERN FRÅN BÖRJAN
!asa841-k8.bin
hostname DRAKENSBERG
domain-name default.domain.invalid
enable password XXXXXXX
names
interface Vlan1
nameif inside
security-level 100
ip address 172.16.12.4 255.255.255.0
interface Vlan10
nameif outside
security-level 0
ip address 97.XX.XX.20 255.255.255.248
interface Ethernet0/0
switchport access vlan 10
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
dns server-group DefaultDNS
domain-name default.domain.invalid
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
access-list nonat extended permit ip 172.16.12.0 255.255.255.0 10.10.10.0 255.255.255.0
access-list MSS_EXCEEDED_ACL extended permit tcp any any
access-list VPN-SPLIT-TUNNEL remark VPN SPLIT TUNNEL
access-list VPN-SPLIT-TUNNEL standard permit 172.16.12.0 255.255.255.0
tcp-map MSS-MAP
exceed-mss allow
pager lines 24
logging enable
logging timestamp
logging buffer-size 8192
logging console notifications
logging buffered notifications
logging asdm notifications
mtu inside 1500
mtu outside 1500
ip local pool VPN 10.10.10.1-10.10.10.40 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
asdm image disk0:/asdm-625-53.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list nonat
nat (inside) 1 172.16.12.0 255.255.255.0
route outside 0.0.0.0 0.0.0.0 97.XX.XX.17 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 172.16.12.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 172.16.12.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
group-policy VPNOFFICE internal
group-policy VPNOFFICE attributes
dns-server value 215.122.145.18
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN-SPLIT-TUNNEL
default-domain value VPNOFFICE
split-dns value 215.122.145.18
msie-proxy method no-proxy
username admin password XXXXXX privilege 15
username Daniel password XXXXX privilege 0
username Daniel attributes
vpn-group-policy VPNOFFICE
tunnel-group VPNOFFICE type remote-access
tunnel-group VPNOFFICE general-attributes
address-pool VPN
default-group-policy VPNOFFICE
tunnel-group VPNOFFICE ipsec-attributes
pre-shared-key XXXXXXXXXX
class-map MSS_EXCEEDED_MAP
match access-list MSS_EXCEEDED_ACL
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect icmp error
inspect pptp
inspect ipsec-pass-thru
inspect icmp
class MSS_EXCEEDED_MAP
set connection advanced-options MSS-MAP
service-policy global_policy global
privilege cmd level 3 mode exec command perfmon
privilege cmd level 3 mode exec command ping
privilege cmd level 3 mode exec command who
privilege cmd level 3 mode exec command logging
privilege cmd level 3 mode exec command failover
privilege cmd level 3 mode exec command packet-tracer
privilege show level 5 mode exec command import
privilege show level 5 mode exec command running-config
privilege show level 3 mode exec command reload
privilege show level 3 mode exec command mode
privilege show level 3 mode exec command firewall
privilege show level 3 mode exec command asp
privilege show level 3 mode exec command cpu
privilege show level 3 mode exec command interface
privilege show level 3 mode exec command clock
privilege show level 3 mode exec command dns-hosts
privilege show level 3 mode exec command access-list
privilege show level 3 mode exec command logging
privilege show level 3 mode exec command vlan
privilege show level 3 mode exec command ip
privilege show level 3 mode exec command ipv6
privilege show level 3 mode exec command failover
privilege show level 3 mode exec command asdm
privilege show level 3 mode exec command arp
privilege show level 3 mode exec command route
privilege show level 3 mode exec command ospf
privilege show level 3 mode exec command aaa-server
privilege show level 3 mode exec command aaa
privilege show level 3 mode exec command eigrp
privilege show level 3 mode exec command crypto
privilege show level 3 mode exec command vpn-sessiondb
privilege show level 3 mode exec command ssh
privilege show level 3 mode exec command dhcpd
privilege show level 3 mode exec command vpnclient
privilege show level 3 mode exec command vpn
privilege show level 3 mode exec command blocks
privilege show level 3 mode exec command wccp
privilege show level 3 mode exec command webvpn
privilege show level 3 mode exec command module
privilege show level 3 mode exec command uauth
privilege show level 3 mode exec command compression
privilege show level 3 mode configure command interface
privilege show level 3 mode configure command clock
privilege show level 3 mode configure command access-list
privilege show level 3 mode configure command logging
privilege show level 3 mode configure command ip
privilege show level 3 mode configure command failover
privilege show level 5 mode configure command asdm
privilege show level 3 mode configure command arp
privilege show level 3 mode configure command route
privilege show level 3 mode configure command aaa-server
privilege show level 3 mode configure command aaa
privilege show level 3 mode configure command crypto
privilege show level 3 mode configure command ssh
privilege show level 3 mode configure command dhcpd
privilege show level 5 mode configure command privilege
privilege clear level 3 mode exec command dns-hosts
privilege clear level 3 mode exec command logging
privilege clear level 3 mode exec command arp
privilege clear level 3 mode exec command aaa-server
privilege clear level 3 mode exec command crypto
privilege cmd level 3 mode configure command failover
privilege clear level 3 mode configure command logging
privilege clear level 3 mode configure command arp
privilege clear level 3 mode configure command crypto
privilege clear level 3 mode configure command aaa-server
prompt hostname context
Cryptochecksum:aaa1f198bf3fbf223719e7920273dc2e
: end

I didn't realise I had that crypto settings on, thanks my bad!!!
But... the 172.16.12.0 network is directly connected, the Router (that to be honest is a firewall) / switches is all on the same subnet (172.16.12.X/24), so sorry I didn't explain thoroughly, was more wondering about the GW and didn't want to overcomplicate things..
The Firewall/Router dosen't do any routing, so it should work right (I you count out the firewalling in the firewall and so forth, there shouldn't be any problems accomplishing this with the ASA)? The Firewall is more a DHCP for the clients/Firwall for the clients.. this will change in the future.. it will be removed,
the vpn network is staticly routed back to my ASA in that firewall...
I don't like this solution.. but this is who it looks.. for now..
(VPN network is 10.10.10.X/24)
But... shouldn't I see a default gateway under ipconfig when I'm connected to the VPN from internet, on the vpn client that's vpned in, is this correct?
THANKS for all the help!

Windows 8.1 Pro Need command to disable "Use default gateway on remote network" option on VPN connection"

Hello!
I want to create bat script to create several VPN connection.
There is powershell command to create vpn connection:
add-vpnconnection -name "Test VPN" -serveraddress "vpn.example.com" -splittunneling -tunneltype "pptp"
And I need to create VPN connection without the option "Use default gateway on remote network" option on VPN connection"
Or modify this option on existent VPN connection with command.
Please help me to find command option or other command to disable "Use default gateway on remote network" option on VPN connection" feature.

http://technet.microsoft.com/nl-nl/library/ee431701%28v=ws.10%29.aspx RouteIPv4TrafficOverRAS True – Add a default gateway on the VPN connection False – Do not add default gateway on the VPN connection

Can I enable "Use default gateway on remote network" on VPN connection using Group Policy?

Hi,
First timer here so please bear with me!
Environment: Domain Windows 2003, Clients: Windows 7 and Windows XP (with Client Side Extensions pushed out)
When creating a VPN connection on a client machine manually with default settings the "Use default gateway on remote network" found in [Connection Properties - Networking - IPv4 - Advanced] is enabled, which is good as we don't allow split-tunneling.
I have a test GPO that creates a new VPN Connection [Computer Config - Preferences - Control Panel - Network Options], but the above setting is unticked.
Am I missing something on the options for the GP preference to set this automtically?
I can write a script to directly change the C:\Users\All Users\Microsoft\Network\Connections\Pbk\rasphone.pbk file but would prefer if I could sort it all out using Group Policy.
Any help would be greatly appreciated!
Thanks a lot!
David

Shane,
There is actually a way to set the "Use default gateway on remote network" through Group Policy Preferences. And this may even be a better way to do it, because you may change this flag without touching any other settings, or other VPN connections.
(All VPN connections are stored in the same .pbk file.)
Here's the trick: Opening the .pbk file in notepad, I realized that this is actually an oldstyle ini-structured file. And Group Policy Preferences can update ini files! In the .pbk file the section names are the VPN connections names, like [My VPN],
and the property IpPrioritizeRemote is the flag "Use default gateway on remote network".
So, in Group Policy Management Editor, go to Preferences / Windows Settings / Ini Files.
Create a new object with Action = Update, and File Path =
C:\ProgramData\Microsoft\Network\Connections\pbk\rasphone.pbk
(If this is where your file is located, I guess it is in c:\users if the VPN connection is made for a single user.)
Section Name should be the display name of your VPN connection, without the brackets.
Property Name = IpPrioritizeRemote
Property Value = 1
Peter, www.skov.com, Denmark
Peter :-)
This is great, but just one question. I also want to append a list of DNS Sufixes in order (when viewing a VPN properties, this is buried in
"Networking --> IPv4/6 --> Advanced --> DNS --> Append these DNS Suffixes (in order)". However, for the VPNs I have manually created with this list populated, I can't see any entries in the rasphone.pbk. Does anyone know
where these are stored?
Cheers.

VPN Clients getting different default gateways

Hello,
We have a new Cisco ASA 5520 and are trying to setup the VPN with split tunneling. We mostly have clients running XP and the problem is that some of the clients connect (using Cisco Anyconnect 2.5) and the split tunneling works as expected --these clients keep their default gateway-- and then some clients connect and get a default gateway of 192.168.119.1 (our VPN addresses subnet) and of course these users cannot connect to the internet while connected to the VPN.
Here is our config:
ASA Version 9.1(1)
hostname xxxxxx
names
name 178.239.80.0 Deny178.239.80.0 description 178.239.80.0
name 74.82.64.0 Deny74.82.64.0 description 74.82.64.0
name 173.247.32.0 Deny173.247.32.0 description 173.247.32.0
name 193.109.81.0 Deny193.109.81.0 description 193.109.81.0
name 204.187.87.0 Deny204.187.87.0 description 204.187.87.0
name 206.51.26.0 Deny206.51.26.0 description 206.51.26.0
name 206.53.144.0 Deny206.53.144.0 description 206.53.144.0
name 67.223.64.0 Deny67.223.64.0 description 67.223.64.0
name 93.186.16.0 Deny93.186.16.0 description 93.186.16.0
name 216.9.240.0 Deny216.9.240.0 description 216.9.240.0
name 68.171.224.0 Deny68.171.224.0 description 68.171.224.0
ip local pool PAIUSERS 192.168.119.10-192.168.119.100 mask 255.255.255.0
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 63.86.112.194 255.255.255.192
interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 192.168.129.5 255.255.255.192
interface GigabitEthernet0/2
nameif dmz
security-level 10
ip address 192.168.20.10 255.255.255.0
interface GigabitEthernet0/3
nameif vpn_dmz
security-level 25
ip address 192.168.30.10 255.255.255.0
interface Management0/0
management-only
shutdown
nameif management
security-level 100
ip address 192.168.102.4 255.255.255.0
object network obj-192.168.119.0
subnet 192.168.119.0 255.255.255.0
access-list outside_access_in extended permit ip host 192.168.119.11 host 192.168.35.23
access-list outside_access_in extended permit object-group TCPUDP any4 object-group DM_INLINE_NETWORK_3 object-group UDP_TCP_Domain inactive
access-list outside_access_in extended permit udp any4 object obj-192.168.30.11 eq isakmp
access-list outside_access_in extended permit ip any4 object obj-192.168.30.11
access-list outside_access_in extended permit udp any4 object obj-192.168.30.11 object-group UDP10000
access-list outside_access_in extended permit udp any4 object-group DM_INLINE_NETWORK_7 eq domain inactive
access-list outside_access_in extended permit tcp any4 object-group DM_INLINE_NETWORK_8 eq domain inactive
access-list outside_access_in extended permit tcp host 216.81.43.190 host 192.168.35.30 eq ssh inactive
access-list outside_access_in extended permit tcp host 216.81.43.190 object obj-192.168.35.30 object-group DM_INLINE_TCP_6 inactive
access-list outside_access_in extended permit tcp any4 object-group DM_INLINE_NETWORK_9 eq www inactive
access-list outside_access_in extended permit tcp any4 object obj-192.168.30.11 eq www
access-list outside_access_in extended permit esp any4 object obj-192.168.30.11
access-list outside_access_in extended permit tcp any4 object obj-192.168.35.41 eq www
access-list outside_access_in extended permit tcp any4 object obj-192.168.35.41 eq https
access-list outside_access_in extended permit tcp any4 host 192.168.35.34 eq https
access-list outside_access_in extended permit object-group TCPUDP any4 object obj-192.168.35.30 object-group Ports_UDpTCP
access-list outside_access_in extended permit tcp any4 object obj-192.168.35.30 object-group DM_INLINE_TCP_7
access-list outside_access_in extended permit tcp any4 object obj-192.168.35.30 eq ftp
access-list outside_access_in extended permit object-group TCPUDP any4 host 63.86.112.248
access-list outside_access_in extended permit udp any4 host 162.95.80.115 eq isakmp
access-list outside_access_in extended permit tcp any4 host 162.95.80.115 object-group Ports_115
access-list outside_access_in extended permit udp any4 host 162.95.80.115 object-group Ports_2746_259
access-list outside_access_in extended permit object-group TCPUDP any4 host 63.86.112.245 object-group Service_Group_245 inactive
access-list outside_access_in extended permit object-group TCPUDP any4 object obj-192.168.35.40 object-group UDP_TCP_Domain
access-list outside_access_in extended permit tcp any4 object obj-192.168.35.40 object-group DM_INLINE_TCP_2
access-list outside_access_in extended permit tcp any4 object obj-192.168.129.11 object-group DM_INLINE_TCP_1
access-list outside_access_in extended permit object-group TCPUDP any4 object obj-192.168.129.11 object-group UDP_TCP_Domain
access-list outside_access_in extended permit tcp any4 object obj-192.168.129.11 object-group Network_Service_2703_6277
access-list outside_access_in extended permit udp any4 object obj-192.168.129.11 object-group UDP_443
access-list outside_access_in extended permit ip any4 host 192.168.101.75 inactive
access-list outside_access_in extended permit tcp any4 host 64.78.239.50 eq www
access-list outside_access_in extended permit tcp any4 host 64.78.239.54 object-group TCP_4445
access-list outside_access_in extended permit icmp any4 any4
access-list outside_access_in extended permit udp any4 object obj-192.168.35.40 object-group UDP_443
access-list outside_access_in extended permit tcp any4 host 63.86.112.204 object-group DM_INLINE_TCP_5
access-list outside_access_in extended permit tcp any4 host 63.86.112.204
access-list outside_access_in extended permit udp any4 host 63.86.112.204
access-list outside_access_in extended permit object-group TCPUDP any4 host 192.168.102.12 object-group Network_Server_1194
access-list outside_access_in extended permit tcp any4 host 192.168.102.12 eq www
access-list outside_access_in extended permit tcp any4 host 192.168.102.12 eq https
access-list outside_access_in extended permit object-group TCPUDP any4 object obj-192.168.35.41 object-group Network_Server_1194
access-list outside_access_in extended permit tcp any4 object obj-192.168.35.12 eq www
access-list outside_access_in extended permit tcp any4 object obj-192.168.35.12 object-group DM_INLINE_TCP_3
access-list outside_access_in extended permit tcp any4 host 63.86.112.193 object-group Network_Service_TCP_1194
access-list outside_access_in extended deny tcp object Deny206.51.26.0 object obj-192.168.35.40 eq https
access-list outside_access_in extended deny tcp object Deny193.109.81.0 object obj-192.168.35.40 eq https
access-list outside_access_in extended deny tcp object Deny204.187.87.0 object obj-192.168.35.40 eq https
access-list outside_access_in extended deny tcp object Deny206.53.144.0 object obj-192.168.35.40 eq https
access-list outside_access_in extended deny tcp object Deny216.9.240.0 object obj-192.168.35.40 eq https
access-list outside_access_in extended deny tcp object Deny67.223.64.0 object obj-192.168.35.40 eq https
access-list outside_access_in extended deny tcp object Deny93.186.16.0 object obj-192.168.35.40 eq https
access-list outside_access_in extended deny tcp object Deny68.171.224.0 object obj-192.168.35.40 eq https
access-list outside_access_in extended deny tcp object Deny74.82.64.0 object obj-192.168.35.40 eq https
access-list outside_access_in extended deny tcp object Deny178.239.80.0 object obj-192.168.35.40 eq https
access-list outside_access_in extended deny tcp object Deny173.247.32.0 object obj-192.168.35.40 eq https
access-list vpn_dmz_access_in extended permit ip host 192.168.35.23 192.168.119.0 255.255.255.0
access-list vpn_dmz_access_in extended permit gre host 192.168.30.11 any4
access-list vpn_dmz_access_in extended permit tcp any4 host 23.0.214.60 eq https
access-list vpn_dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_28 any4
access-list vpn_dmz_access_in extended permit tcp any4 object obj-192.168.35.105 object-group DM_INLINE_TCP_4
access-list vpn_dmz_access_in extended permit esp any4 object obj-192.168.35.105
access-list vpn_dmz_access_in extended permit tcp any4 object obj-192.168.35.105
access-list vpn_dmz_access_in extended permit icmp any4 object obj-192.168.35.105
access-list vpn_dmz_access_in extended permit tcp any4 host 192.168.129.11
access-list vpn_dmz_access_in remark RDP
access-list vpn_dmz_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq 3389
access-list vpn_dmz_access_in extended permit icmp any4 object obj-192.168.35.23
access-list inside_nat0_outbound extended permit ip any4 192.168.119.0 255.255.255.0
access-list ftp-timeout extended permit tcp host 216.81.43.190 host 63.86.112.248
access-list ftp-timeout extended permit tcp host 63.86.112.248 host 216.81.43.190
access-list ftp-timeout extended permit tcp host 192.168.35.30 host 216.81.43.190
access-list ftp-timeout extended permit tcp host 216.81.43.190 host 192.168.35.30
access-list Split_Tunnel_List remark northwoods
access-list Split_Tunnel_List standard permit host 192.168.35.23
access-list Split_Tunnel_List remark paits2
access-list Split_Tunnel_List standard permit host 192.168.35.198
access-list Split_Tunnel_List standard deny 192.168.102.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended deny ip any4 any4
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any4 any4 eq netbios-ns
access-list IS_Split_Tunnel standard permit 192.168.102.0 255.255.255.0
access-list IS_Split_Tunnel standard permit 192.168.82.0 255.255.255.0
access-list IS_Split_Tunnel standard permit 192.168.35.0 255.255.255.0
nat (inside,outside) source static object-192.168.35.0 object-192.168.35.0 destination static obj-192.168.119.0 obj-192.168.119.0 no-proxy-arp route-lookup
nat (inside,outside) source static obj-192.168.82.0 obj-192.168.82.0 destination static obj-192.168.119.0 obj-192.168.119.0 no-proxy-arp route-lookup
nat (inside,outside) source static obj-192.168.102.0 obj-192.168.102.0 destination static obj-192.168.119.0 obj-192.168.119.0 no-proxy-arp route-lookup
webvpn
enable outside
enable inside
enable dmz
anyconnect-essentials
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2
anyconnect profiles pairemoteuser disk0:/pairemoteuser.xml
anyconnect enable
tunnel-group-list enable
group-policy PAIGroup internal
group-policy PAIGroup attributes
vpn-tunnel-protocol ssl-clientless
webvpn
url-list value PAI
group-policy PAIUSERS internal
group-policy PAIUSERS attributes
wins-server value 192.168.35.57
dns-server value 192.168.35.57
vpn-tunnel-protocol ikev2 ssl-client ssl-clientless
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Split_Tunnel_List
default-domain none
webvpn
anyconnect firewall-rule client-interface private value vpn_dmz_access_in
anyconnect profiles value pairemoteuser type user
group-policy PAIIS internal
group-policy PAIIS attributes
wins-server value 192.168.35.57
dns-server value 192.168.35.57
vpn-tunnel-protocol ikev2 ssl-client ssl-clientless
split-tunnel-policy tunnelspecified
split-tunnel-network-list value IS_Split_Tunnel
default-domain none
webvpn
anyconnect firewall-rule client-interface private value vpn_dmz_access_in
anyconnect profiles value pairemoteuser type user
group-policy DfltGrpPolicy attributes
banner value Welcome to PAI
wins-server value 192.168.35.57
dns-server value 192.168.35.57
address-pools value PAIUSERS
webvpn
anyconnect firewall-rule client-interface public none
anyconnect firewall-rule client-interface private value vpn_dmz_access_in
anyconnect ask enable default anyconnect timeout 5
group-policy Anyconnect internal
: end

Check is the users fall into DfltGrpPolicy because it has no split tunneling active.
Michael
Please rate all helpful posts

Physical Interface not present in show ip route connected

Hi,
Thanks for reading my post.
I have a reccurent issue with a CISCO881-K9.
My WAN interface is regularly unsuable even if it's UP/UP. I can't even ping the interface from the router itself.
A reboot solves the issue. But now I have time and I'd like to get a proper understanding of what's going on.
The route doesn't appear in "show ip route connected".
Router#show ip interface brief
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0              unassigned      YES unset up                    up
FastEthernet1              unassigned      YES unset down                  down
FastEthernet2              unassigned      YES unset down                  down
FastEthernet3              unassigned      YES unset down                  down
FastEthernet4              X.Y.Z.82    YES NVRAM up                    up
Loopback0                  10.31.129.5     YES NVRAM up                    up
NVI0                       X.Y.Z.82    YES unset up                    up
Tunnel0                    10.32.129.1     YES NVRAM up                    down
Vlan1                      172.22.129.102 YES NVRAM up                    up
Router#ping X.Y.Z.82
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to X.Y.Z.82, timeout is 2 seconds:
Success rate is 0 percent (0/5)
Router#
Router#show ip route
Gateway of last resort is X.Y.Z.81 to network 0.0.0.0
S*    0.0.0.0/0 [1/0] via X.Y.Z.81
      10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
R        10.30.129.0/24 [120/1] via 172.22.129.101, 00:00:08, Vlan1
R        10.31.129.1/32 [120/1] via 172.22.129.101, 00:00:08, Vlan1
C        10.31.129.5/32 is directly connected, Loopback0
      172.22.0.0/16 is variably subnetted, 3 subnets, 2 masks
S        172.22.128.0/24 [1/0] via 172.28.28.254
C        172.22.129.0/24 is directly connected, Vlan1
L        172.22.129.102/32 is directly connected, Vlan1
      172.27.0.0/24 is subnetted, 1 subnets
S        172.27.0.0 [1/0] via 172.28.28.254
      172.28.0.0/24 is subnetted, 1 subnets
R        172.28.28.0 [120/2] via 172.22.129.101, 00:00:08, Vlan1
      172.30.0.0/24 is subnetted, 1 subnets
S        172.30.1.0 [1/0] via 172.28.28.254
      172.31.0.0/24 is subnetted, 1 subnets
S        172.31.0.0 [1/0] via 172.28.28.254
S     192.0.0.0/16 [1/0] via 172.28.28.254
      192.168.48.0/32 is subnetted, 1 subnets
S        192.168.48.247 [1/0] via 172.28.28.254
      192.168.84.0/32 is subnetted, 1 subnets
S        192.168.84.247 [1/0] via 172.28.28.254
S     192.168.101.0/24 [1/0] via 172.28.28.254
R     192.168.104.0/24 [120/2] via 172.22.129.101, 00:00:08, Vlan1
Router#show ip route connected
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
       + - replicated route, % - next hop override
Gateway of last resort is X.Y.Z.81 to network 0.0.0.0
      10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
C        10.31.129.5/32 is directly connected, Loopback0
      172.22.0.0/16 is variably subnetted, 3 subnets, 2 masks
C        172.22.129.0/24 is directly connected, Vlan1
L        172.22.129.102/32 is directly connected, Vlan1
interface FastEthernet4
description WAN
ip address X.Y.Z.82 255.255.255.252
no ip proxy-arp
ip flow ingress
ip nat outside
ip virtual-reassembly in
ip tcp adjust-mss 1300
duplex full
speed 100
keepalive 3
crypto map MYSTREAM-MAP
hold-queue 224 in
end
Router#show interfaces fastEthernet 4
FastEthernet4 is up, line protocol is up
Hardware is PQII_PRO_UEC, address is 4403.a738.3c02 (bia 4403.a738.3c02)
Description: WAN
Internet address is X.Y.Z.82/30
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (3 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:06, output 00:00:35, output hang never
Last clearing of "show interface" counters never
Input queue: 0/224/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
     26675 packets input, 1826301 bytes
     Received 12230 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog
     0 input packets with dribble condition detected
     44029 packets output, 8969818 bytes, 0 underruns
     0 output errors, 0 collisions, 4 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     3 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
Could you help on this? Or lead me to Tshoot that problem.
By the way the interface 4 is connected to an ISP Modem (TWC in US).
Thanks,
William

Hi,
Thanks for your answer. I've checked the release notes and there is no bug about that.
I think I must use the WAN interface which is fastethernet 4. I'm not able to change the patch cable for now.
What could be the cause?
show version
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Wed 21-Mar-12 00:27 by prod_rel_team
ROM: System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Router uptime is 1 week, 3 hours, 6 minutes
System returned to ROM by reload at 08:12:54 UTC Fri Oct 3 2014
System restarted at 08:14:30 UTC Fri Oct 3 2014
System image file is "flash:c880data-universalk9-mz.151-4.M4.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
If you require further assistance please contact us by sending email to
[email protected]
Cisco 881 (MPC8300) processor (revision 1.0) with 236544K/25600K bytes of memory.
Processor board ID FGL1652265J
5 FastEthernet interfaces
1 Virtual Private Network (VPN) Module
256K bytes of non-volatile configuration memory.
125440K bytes of ATA CompactFlash (Read/Write)
License Info:
License UDI:
Device#   PID                   SN
*0        CISCO881-K9           FGL1652265J
License Information for 'c880-data'
    License Level: advsecurity   Type: Permanent
    Next reboot license Level: advsecurity
Configuration register is 0x2102

SSL VPN with client, anyconnect.

I've set up a simple test on SSL VPN with client on a 3800.
It didnt work. I assume i have to turn on the IP http server so that the client can hit it.
but when I turned it on, the client goes to SDM, nothing with ssl vpn happened. it tells me the pay is not available.
The underlying routing is fine.
Could you tell me where it is configured wrong?
Config is copied below.
thanks,
Han
=======
Current configuration : 3340 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable password cisco
aaa new-model
aaa authentication login default local
aaa session-id common
no network-clock-participate slot 1
crypto pki trustpoint TP-self-signed-3551041125
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3551041125
revocation-check none
rsakeypair TP-self-signed-3551041125
crypto pki certificate chain TP-self-signed-3551041125
certificate self-signed 01
3082024F 308201B8 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33353531 30343131 3235301E 170D3131 31313135 31383238
30365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 35353130
34313132 3530819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100CFCF CFFAD76A 50DA82C9 8D4E3F90 64AD24EB 5409C5E2 43BC64F3 07F6C0E0
29FF2D71 0DA0D897 2F814BD2 7F817503 429D4BC6 6AD6EEA4 DFA74BAD 0EAF84D5
6ED55EC0 6C637178 BEEBCD1D 184BB90C CA84E974 48003885 87B53F2E 36A04661
23DA2CBB DD8EEE1D 2F25AF9A E21DC288 BF76A17C C1F4BA07 95F09377 A12BE01A
53750203 010001A3 77307530 0F060355 1D130101 FF040530 030101FF 30220603
551D1104 1B301982 17526F75 7465722E 776E7362 6E6F632E 696E7465 726E616C
301F0603 551D2304 18301680 14BE9E8F ED788928 560D7CA1 EED89B0D DE34D772
5D301D06 03551D0E 04160414 BE9E8FED 78892856 0D7CA1EE D89B0DDE 34D7725D
300D0609 2A864886 F70D0101 04050003 818100BC 4A2A3C47 7BF809AF 78EE0FD9
73692913 F280765E BAFAECAB ED32C38D 3030810B C62C7F45 13C8A6EE AE96A891
CDD4C78B 803299AD EB098B27 383CEF6F 0E2B811F 3ECFADBA 07CD0AC6 BBB8C5FE
B2FC0FD8 562B7100 BB28036E 4575D1F5 B17687C6 8EACBD66 A9E52FEE A030E69A
CAAE9F1B 618FA59D 02C25BC8 77D6CAC2 C7E56F
quit
dot11 syslog
ip cef
multilink bundle-name authenticated
voice-card 0
no dspfarm
username cisco1 privilege 15 secret 5 $1$L2RA$Zqs6FLce5Ns5fny5aRL49/
archive
log config
hidekeys
interface GigabitEthernet0/0
ip address dhcp
duplex auto
speed auto
media-type rj45
end
interface Loopback1
ip address 1.1.1.1 255.255.255.0
interface GigabitEthernet0/0
ip address dhcp
duplex auto
speed auto
media-type rj45
ip local pool svc-poll 1.1.1.50 1.1.1.100
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.1.254
ip http server
no ip http secure-server
control-plane
line con 0
logging synchronous
line aux 0
line vty 0 4
scheduler allocate 20000 1000
webvpn gateway SSLVPN
ip interface GigabitEthernet0/0 port 443
ssl trustpoint local
inservice
webvpn install svc flash:/webvpn/svc.pkg
webvpn context SSLVPN
ssl authenticate verify all
policy group default
   functions svc-required
   svc default-domain "test.org"
   svc keep-client-installed
   svc split dns "primary"
default-group-policy default
gateway SSLVPN
inservice
end

Using the SDM follow the below config example
http://www.cisco.com/en/US/products/ps6496/products_configuration_example09186a008071c58b.shtml
The text "cisco 3800 ssl vpn configuration" in my favorite search engine, identified the above.
HTH>

VPN connection created with CMAK fails to update routing table on Windows 8.1 with error 8000ffff

When my clients connect their CMAK-created VPN, it fails to run the script to set their routing table with the following error:
Custom script (to update your routing table) failed (8000ffff)
My objective is to create a VPN connection with split tunneling - does not use the VPN connection as the client's default gateway.
All my clients are on Windows 8.1 64-bit, and are logged in with Administrative privileges
My VPN Clients are on 10.242.2.0/24, my internal network is on 10.172.16.0/24
I want only traffic for 10.172.16.0 to go via the VPN. Everything else should go via the client's internet connection
My Connection Manager Administration Kit profile, was created on Windows 2012 R2 CMAK with the following settings:
"Make this connection the client's default gateway" is UNticked on the IPv4 tab.
Define a routing table update is specified with a text file containing:
+++ Start of txt file +++
REMOVE_GATEWAY
add 10.172.16.0 mask 255.255.255.0 default metric default if default
+++ End of txt file +++
The txt file is saved in DOS/Windows format (not Unicode or UTF-8 which I've read causes problems)
I've tried everything in lower and upper case in the txt file after reading that the file might be case sensitive
The following appears on the client with logging enabled:
[cmdial32] 10:42:34
03 Pre-Init Event CallingProcess = C:\WINDOWS\system32\rasautou.exe
[cmdial32] 10:42:40
04 Pre-Connect Event ConnectionType = 1
[cmdial32] 10:42:40
06 Pre-Tunnel Event UserName = UserName Domain = DUNSetting = VPN (L2TP x64 NoGW) Tunnel DeviceName = TunnelAddress = vpn.mydomain.tld
[cmdial32] 10:42:43
07 Connect Event
[cmdial32] 10:42:43
09 Custom Action Exe ActionType = Connect Actions Description = (none) ActionPath = CMDL32.EXE. The program was launched successfully.
[cmdial32] 10:42:43
08 Custom Action Dll ActionType = Connect Actions Description = to update your routing table ActionPath = C:\Users\UserName\AppData\Roaming\Microsoft\Network\Connections\Cm\VPN64\CMROUTE.DLL ReturnValue
= 0x8000ffff
[cmdial32] 10:42:43
21 On-Error Event ErrorCode = -2147418113 ErrorSource = to update your routing table
[cmdial32] 10:42:43
13 Disconnect Event CallingProcess = C:\WINDOWS\system32\cmdial32.dll
Where can I find out what error codes 8000ffff or -2147418113 mean?

That was it. Thanks, Steven
"By default, the dial-up entry and the VPN entry have Make this connection the default gateway selected.
Leave this default in place, and remove any gateways by using the REMOVE_GATEWAY command in the routing table update file itself."
It seems counter-intuitive to leave
Make this connection the default gateway selected, when I specifically don't want that behaviour, but leaving it selected and using REMOVE_GATEWAY works for me.

Default Gateway address for multiple VPN users/clients

Hello,
We need some help with a VPN setup for a school project.
What we want to do:
We would like to have aprox. 10 different VPN uses that can connect to our Windows Server 2012 R2 which is setup as a VPN server, by the Role called Remote access. And the VPN server is working and we are able to connect to it from another location/computer.
Our current setup:
We have a Cisco router, that are configured with 10 Vlans, from Vlan 10 to Vlan 20, and a managament Vlan called Vlan 100.
The Cisco router is also acting as DHCP server, so inside each Vlan the DHCP gives IP addresses to that specific Vlan, Ex: Vlan 10 has a 192.168.10.0/24 network. Vlan 11 has a 192.168.11.0/24 network, and so on. Vlan 100 has 192.168.100.0/24 This Vlan 100
has connection to all the Vlans.
We have internet connection on the Router on port 0 and each Vlan are connected to the internet.
We have setup the VPN server with a static IP configuration so it is inside Vlan 100 with a Default gateway, like 192.168.100.1 So the VPN server is connected to the internet.
In AD we have created a User and assigned a static IP address in the user properties, under the Dial-In tab. Here we give this user this IP 192.168.10.225
Now when we connect to the VPN server useing this user, we have no connection to any of the Vlans (ping) and no internet. When we in cmd write ipconfig we can see that our VPN connection has this IP 192.168.10.225 but a Subnet called 255.255.255.255 and
a Default gateway called 0.0.0.0
We would like the user to recieve the correct IP settings like: If we connect with our user, it should recieve the IP as it does, but also a subnet called 255.255.255.0 and a default gateway called 192.168.10.1
How is this achieved?
The reason we want this is: We want to create a VPN user for each Vlan. So a user with permission to access Vlan 10 but are not able to see the other Vlans, and then a new user to access Vlan 11 but not able to see the other vlans, and so on.
Hope someone is able to help us to understand how this is done.
Thank you in advance.

Hi,
In brief, we can't achieve this. Normally, we would not do this.
Usually, we use firewall or ACL to restrict the remote users.
For example, 192.168.10.100 is assigned to user1 and 192.168.10.101 is assigned to user2. We can use firewall to restrict 192.168.10.100 to access 192.168.10.0/24 and 192.168.10.101 to access 192.168.11.0/24.
Best Regards.
Steven Lee Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Can't find the option to disable "Default Gateway" of a VPN.

Whenever I try to go to the "Networking" tab of a VPN connection. I get the following error.: "Unable to allow the editing of networking components at this time because they are currently being modified elsewhere" This prevents me from
disabling the default gateway of a VPN. Any help is greatly appreciated!

Whenever I try to go to the "Networking" tab of a VPN connection. I get the following error.: "Unable to allow the editing of networking components at this time because they are currently being modified elsewhere" This prevents
me from disabling the default gateway of a VPN. Any help is greatly appreciated!
I have got the same issue using Windows 10 Insider Preview build 10074, please could somebody show us an alternative method to disable the use of the remote default gateway through a VPN ? Thanks.
Edit - From that post : https://social.technet.microsoft.com/Forums/en-US/709f9e02-d903-41a8-b5f8-d0f46d4685bf/how-to-disable-default-gateway-remote-in-vpm-with-windows-10-tp-10049?forum=WinPreview2014General
it seems to be possible to use a PowerShell command to modify this option, by setting "RouteIPv4TrafficOverRAS" to "False" instead of "True" (which is WIndows Default), but I do not know how to do that. Could somebody explain

Routing with more than one default gateway

Hi,
here is my problem:
usually I'm using Internet with WLAN-connection. Sometimes I want to connect my mac additionally with the LAN on work. As soon as I plug in the ethernet, there is a new item in the routing table, so I have two default-gateways - one to the WLAN-router and one to the standard-gateway of my work's LAN.
So for example I cannot take new mails from my private pop-account and for using internet I have to register a proxy-server. That's circuitous!
My idea is to create a plist-file in launchDaemons-directory, that deletes the default-gateway-item to my work's standard-gateway and adds a net-route to this only for my work's network.
Is it really a good idea or nonsens? What's a better way?
Thank you for your help!

So you want to do dual-homing.
First remember that Macs really are setup, out of the box, to be a one connection at time machine. And, there is a service order for interfaces. Which you can set in Systems Prefs Network.
However, I think this is what you are looking for:
open a terminal and do:
sudo sysctl -w net.inet.ip.forwarding=1
This command will allow the Mac to use two defaults gateways. Then it will be up to you to populate the routing table with what route goes to what gateway.
To add a static route every time you boot (taking from Dr. V on techarena)
http://forums.techarena.in/operating-systems/1187193.htm
Code:
sudo route -nv add -net 192.168 -interface en0
To avoid having to do this everytime you reboot:
Code:
cd /System/Library/StartupItems sudo cp -R NetworkExtensions NetworkLocal cd NetworkLocal sudo mv NetworkExtensions NetworkLocal sudo vi NetworkLocal
- replace the startup section with the comand above:
Code:
#!/bin/sh ## # Load network kernel modules ## . /etc/rc.common StartService () { ConsoleMessage "Loading Network Local" route -nv add -net 192.168 -interface en0 } StopService () { return 0 } RestartService () { return 0 } RunService "$1" sudo vi StartupParameters.plist
-- edit it to get
Code:
{ Description = "Network Local"; Provides = ("NetworkLocal"); Requires = ("Network"); OrderPreference = "None"; } cd Resources/English.lproj sudo vi Localizable.strings
-- edit it to get:
Code:
(?xml version="1.0" encoding="UTF-8"?) (!DOCTYPE plist SYSTEM "file://localhost/System/Library/DTDs/PropertyList.dtd") (plist version="0.9") (dict> (key>Loading Network Local(/key) (string>Loading Network Local(/string) (/dict) (/plist)
You could also edit the Network startup file and add the single line but that could get replaced if system is upgraded.

VPN Client : Default Gateway

Hi,
I have ASA 5505 with ASA v 8.0.3 and ASDM v 6.0.3.
The VPN connection works, the client receive the IP from the define pool but the default gateway is not correct. Is it possible to define the gateway in the pool ?
thank you

Dimitri
I am not clear what default gateway you expected, what default gateway you got, or what was no correct about the gateway. Perhaps you can clarify?
In my experience many people are surprised that the gateway address is the clients own address and not some other address in the subnet as we normally expect with a LAN client. But this is normal behavior on what is essentially a point to point connection from the client to the concentrator. Is this perhaps what you were thinking was an error?
HTH
Rick

Connection lost with VPN enabled

I have a server with two NICs, one public internet and one domain intranet. I'm trying to configure this server as a NAT and VPN "edge" device. I am able to configure it as NAT-only, and everything works perfectly. All computers on the private
network have internet access through it, and I'm able to ping it from outside computers.
When I change my NAT service to a "NAT and VPN" service (using RRAS -> "configure and enable routing and remote access"), I lose the ability to ping that server from outside and when I try to connect to the VPN I get an error
"". It's like by configuring it as a VPN server it has blocked any kind of incoming connection, including those that it's designed for (VPN connections).
If I disable the Windows Firewall entirely, it starts working again. I've checked, and the Ping rule is allowed (the file/printer share echo one), and HTTPS/443 is as well (my VPN is a SSTP), so I don't understand why that would make a difference. Any thoughts
on why this might be happening?

Hello,
I've been putting together a new domain network, and just about have it set except for one final issue. I have a Remote Access server that I have configured for SSTP VPN. It has two NICs, one public/internet facing and the other private/intranet facing.
On the network I also have a DNS/DHCP/ADDS server and a NAT router server that has a different public internet connection and acts as the network's default gateway.
The issue I'm having is with configuring the VPN server's network adapter settings. I have two scenarios:
- configure private adapter with static IP address and manually entering the subnet/DNS (and leaving the gateway blank, since it also has a gateway on the public adapter). If I do this, then it won't let me configure a DHCP Relay Agent in RRAS, and although
I can connect to the VPN on a client, the client doesn't have internet access through the VPN.
- configure private adapter as "obtain an IP address automatically". If I do this, then the DHCP Relay Agent configures itself properly, but for some reason when I try to connect to the VPN from the client I get an "Error 0x8007274C: A connection
attempt failed because the connected party did not properly respond after a period of time..."
I tested a work-around where I set the VPN server's private adapter to static IP, connected the client to the VPN, then changed the server's private adapter to "Obtain automatically", let it re-identify, and it worked fine (I had internet access
on the client after that). Obviously, that's not a usable solution though. Any ideas why neither of these configurations work properly, or perhaps suggestions of a different configuration that might?

Physical interface Default Gateway connecting VPN with AnyConnect

Similar Messages

Maybe you are looking for