Pixma Pro 100 low ink warning

Does the Pixma Pro 100 auto stop when insufficient ink is available to print properly or is the 'low ink' warning all you get until the it doesn't print correctly?

Hi mrjcall,
The PIXMA PRO-100 will warn you when the ink is "low" and stop printing when the ink is "out".  Keep in mind that when the low warning appears, you have about 25% of the ink left in your ink tank.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Similar Messages

  • Pixma pro 100 replacement ink

    Can anyone recommend peplacement inks for the puxms pro 100

    Mike Lee's videos are excellent but there are some additional ideas that are good for a beginner.
    The easiest part is the actual filling and the hardest part is getting that original ball plug out of the hole.
    So, the first time is the hardest.
    Additional items you should have handy and a few things that seemed critical to me.
    Use thin disposable gloves or end up with ink-stained hands.
    Have extra pushpins, if you heat them to form a hole in the original plug, the pushpins can deform.
    After you use the heated pushpin, let the ball cool for a bit before trying to screw in the little screw eye.
    Always use electrical tape to seal the vent on top before filling. Cellophane tape can be difficult to get off and tears.
    I bought (from Precision) and used separate syringes and needles for each color to avoid washing while working and minimize color pollution.
    The orange clamp has a rubber disk that is supposed to seal the ink access hole on the bottom. Well, it doesn't always seal. I used a nickel-sized piece of tissue on top of that plug and it caught all the ink that leaked.
    Always, always reset the chip first to minimize potential of spillage.
    The original plug is under the QR code on top of the cartridge so without poking around I just sliced the plastic layer in that area off and all went well.
    Reaming the filler hole with the 5/32 drill is crucial; that makes an easily and perfectly seal-able hole for the new plugs.
    Rinse out the syringe well and then, after blowing air out the needle to expel any water, leave the plunger and barrel separated to dry. I used filtered water to be certain there would be as little residue in the needle as possible.

  • Canon Pixma pro 100 Ink how to identify the black cartridges when label was accidently removed

    I just started putting a new Canon Pixma Pro 100 printer together- I was not thinking and removed two of the grey (light), and grey cartridges labels. Now I do not know which to put in the slots, I cannot see any gradient by holding them up to the light, and the actual cartridge is not marked. I am soooo dumb, any suggestions.

    You  got a 50/50 chance.  Go for it!  
    EOS 1Ds Mk III, EOS 1D Mk IV EF 50mm f1.2 L, EF 24-70mm f2.8 L,
    EF 70-200mm f2.8 L IS II, Sigma 120-300mm f2.8 EX APO
    Photoshop CS6, ACR 8.7, Lightroom 5.7

  • Canon Pixma Pro-100 printer ejects 3.8 in of a 4X6 paper and prints only 2.2 in of the image printing from Photoshop CS6, I'm sure I set everything correctly - what could I be missing?

    Using Mac Pro running Snow Leopard (10.6.8) & editing & printing from Photoshop CS 6.
    Have new Canon Pixma Pro-100 printer and set it up yesterday.  First thing printed was a
    document from MS Word (a letter) 8.5 X 11 plain paper - this came out OK.  Next I fire up
    Photoshop and open a 4 X 6 inch image to do a test print.  I set it up in the print dialog as
    4X6 paper, Canon's Pro Glossy paper profile, rear tray, standard print quality, Photoshop
    manages the color.  I load the paper in the rear tray close the covers and hit print.  Now, when
    it starts to print the printer moves about 3.8 inches of paper out of the printer and starts printing
    on the remaining 2.2 inches then spits the paper out.  It does this in Photoshop (any image it doesn't
    matter), and it does it printing from Capture NX.  I have been able to get it to print on the paper
    correctly using Apple's Preview program but that that's not going to do me any good.  I was on
    the phone with Canon tech support for about 2 hours and they were completely puzzled suggesting
    I would have to use Canon's printing apps instead to print - that doesn't do me any good either.
    I want to be able to print from Photoshop.  Any one every heard of this or experienced the same
    problem? Thanks JamesD!

    Hello again. I recognize that a print is good if you like it and bad if you don't, despite what others might say, but I will at least share my experiences. They might help you or others who are following this thread.
    My monitor is calibrated with Spyder 3. Gamma 2.2, 6500K, 83 cd/m^2. Contrast at 50%; brightness about 52%. My monitor lets me choose blackness level - it defaults to 50%.
    When I print the test image I linked to above, using Lightroom, with no adjustments, my technical output is as follows:
    Middle step wedge shows twelve disticnt steps. Whitest step is color of unprinted paper.
    It varies from paper to paper, but I can discerne at least the 252 step and on some papers 253 - telling me I have good highlight detail.
    On the black side I discerne 8 or 10, nothing lower. (That sounds like what you are reporting).
    Artistically I am very happy how my print looks - nice red strawberries, good flesh tones, etc.
    One my monitor, the on-screen image is almost identical to the print. I am surprised that you can see the 2 wedge step on screen at a very similar brightness.
    I also checked out this B&W test image:
    http://www.northlight-images.co.uk/article_pages/bw_printing/bw-test-image-2.html
    You are probably aware of this since you are printing with Print Studio Pro, but others may not be.
    You can print a series of test images:
    find the one that best suits your taste, enter the calibration values in PSP, and save them as a custom setting. Then, each time you want to print recall the setting.
    You can do a similar thing in Lightroom using the printer driver and User Templates.
    There would be some one-time trial and error to that approach.
    John Hoffman
    Conway, NH
    1D Mark IV, Rebel T5i, Pixma PRO-100, MX472

  • Questions before I purchase a Pixma Pro-100

    Haven't spent any time over here on the printer side of the forum and I didn't see my questions posted so I will post them here hoping they aren't repeat questions.
    Been researching photo printers and found the Pixma Pro-100 to suit my needs.  This will be my first "photo' printer.  I will be printing high res images from Lightroom (hopefully the plug-in works great).
    1.  Since I will be a light user (maybe printing once a month or even every other month), I'm concerned about plugged print nozzles or dried up ink.  Does anyone have any experience on plugged nozzles or dried up ink?  I do have a Canon iP100 for work which gets light use (also about once every other month) and I have not had any plugged nozzles so I'm optimistic that I will not have issues with the Pro-100 but I sure would appreciate some experienced feedback.
    2.  I see the printer comes with "Setup" ink tanks.  Any idea  how much printing I can get from these or should I just buy a set of ink tanks right up front?
    3.  Which refill set of tanks?  If I'm only doing color printing, should I just buy the 5 color set plus black?  I'm assuming the 8 color set (which includes the two shades of gray) are for gray scale printing.  Once I get rolling, I'll obviously buy whatever is most economical but right now I don't know.
    4.  Paper -  I see Canon has listed their paper plus all tested compatible paper on their web page.   I do have some HP photo paper (not listed as compatible) that I would like to use up.  I used this in the past on standard inkjet printers including the Canon ip100.   Any idea how this paper will hold up on the Pro-100?  Paper is HP Premium photo soft gloss and HP Premium photo high gloss.  Of course I can try it but rather not waste ink if someone out there knows better.
    5.  I'm sure this is a dumb question for most, but is it best to print from RAW or convert and print JPG?
    Thanks in advance, appreciate any feedback.

    If I were going to use LR 4 to print, I would let it do it's thing with the proprietary file LR uses. I would not try it from a RAW or convert to tiff. Not to say you can't get good results but to lessen any more issues into it until you get comfortable with the new printer.
    One thing about LR, remember to set your page size in the "page set-up" tab first.
    EOS 1Ds Mk III, EOS 1D Mk IV EF 50mm f1.2 L, EF 24-70mm f2.8 L,
    EF 70-200mm f2.8 L IS II, Sigma 120-300mm f2.8 EX APO
    Photoshop CS6, ACR 8.7, Lightroom 5.7

  • PIxma Pro 100 - Lightroom Incorrect image sizing for select paper sizes

    I am trying to print from Lightroom to the Pixma Pro 100 using the A3+ Paper size (13"x19")  In Lightroom, the page and printer setups are all correct (verified by Adobe's Tech support) and in the Print Preview area, everything looks great and ready to print.
    Yet when I actually print the image to A3+ paper (and the image nearly fills the entire paper area) the resulting image is serverly cropped on the paper.  In fact is looks like it is cropping the image to 8.5x11, which obviously, only uses a portion of the 13x19 paper size.  It seems that Lighroom or the Canon Printer drivers are not respecting the selected paper size and defaulting to 8.5x11.
    Here is a link to an image of what the print out looks like:
    https://www.dropbox.com/s/mylwpsns0uvr4io/2013-05-20%2009.00.15.jpg
    This does not happen when printing from Print Studio Pro, nor from Photoshop itself.
    I've dealt with Adobe Tech support and Canon - both are point fingers at each other.  Meanwhile I am unable to print anything on larger paper sizes.
    The Pixma Pro is the only printer connected and I've re-installed drivers and checked for updates.  Still the same.  At this point, any comments on the situation would be appreciated.
    Thanks in advance!
    Bruce Johnson
    [email protected]
    Bruce Johnson
    [email protected]

    I am experiencing something like this as well.
    I do almost all my printing in A3+ and I do it all directly from LIghtroom. No problem til sometime this summer (post firmware update). Now whenever I set it up for 13 x 19 (and LR shows that it is 13 X 19) the finished print is actually 7.5 x 11 on the 13 x 19 in paper.
    Incredibly frustrating as I go through time, paper, ink, and tech support (at Canon and Adobe) trying to resolve this.
    Last week a Canon technician walked me through a complete reinstall of the printer and then it worked again. This week it's back to the same mess, and neither  a reinstallation of the printer today nor an update of my LR solfware resolved the problem.
    I learned today that I am able to print the correct size using Print Studio Pro, but I have never used it in the past and I'm reluctant to switch from the functional LR to Canon workflow I had going (where I knew how my printing specs would come out) 

  • So, CAN I turn off the printer's color management? Pixma Pro-100.

    So, I am trying to turn off the color management function for the Pro-100...
    On my Windows desktop, I use Photoshop to print with Canson Rag 210, color profile installed, allow photoshop to manage colors and print a beautiful, perfect print with the Mark 9000. Now, I have the Pixma Pro-100 and using the exact same settings, I print wirelessly with my laptop, and I get these dark, red/orange hued prints that are atrocious.
    I should mention the same exact photograph printed between setups ALWAYS prints better with the Mark 9000 and my desktop. However, when using my laptop and the Mark 9000... Crap. Laptop and Pixma Pro-100... Crap. What is my MAC doing that my desktop is not?! How can identical settings print such drastic results? Photoshop does warn me (newer version on my MAC vs. Windows) to turn off the printer's color management in the printer's settings, but I do not see that option. Maybe I'm missing it? How do I do that? I'm thinking it may help!

    Have you tried printing from the MacBook using Canon Print Studio Pro or letting printer manage colors? I know this doesn't specifically answer your question, but PSP is designed to handle the PS/printer interface.
    Download PSP 1.3.5 from the Canon support site.
    http://www.usa.canon.com/cusa/support/consumer/printers_multifunction/pixma_pro_series/pixma_pro_100...
    John Hoffman
    Conway, NH
    1D Mark IV, Rebel T5i, Pixma PRO-100, MX472

  • Canon Pixma Pro-100 prints very dark

    I see that this is a recuring problem with the Canon Pixma Pro-100, but as nothing I have found online helps I'm asking and are hoping that someone can solve this problem for me.
    Just picked up a Pixma Pro-100 today, and installed it on my 2011 iMac 27" (Yosemite) with downloaded drivers from Canon's website to be sure i have the latest ones. I also checked the printers firmware but that's the latest at 1.100. Wether I'm printing via Lightroom or Photoshop; or via Canon Print Studio Pro, My Image Garden, or via LR / PS directly; with- or without PS as color manager; the prints turns out to be much to dark.
    I have to set an exposure of +2/3 in LR to be anywhere close to getting the same result as on the screen. I'm also careful to select the right ICC profiles for the correct paper. My monitor is calibrated with an Spyder4pro and I also re-calibrated it during this process to see if that helped.
    Well. Long story short; the prints are to dark. So i borrowed my wife's 2013 MacBook Pro (Yosemite) Spyder4pro, and installed the latest drivers from Canon. Again; on this machine the prints are also to dark with about +2/3 to correct for the printer to do something that looks like the monitor. Both monitors are also set to about 30% brightness.
    I also have access to an Epson Stylus Photo R3000 and the prints from this comes out much brighter.
    Sadly I see that many others also have the same problem. So; here's the question. How do I fix this? Do i have to return the printer again and get a refund? Because this is clearly not good enough.
    Solved!
    Go to Solution.

    Hello again. I recognize that a print is good if you like it and bad if you don't, despite what others might say, but I will at least share my experiences. They might help you or others who are following this thread.
    My monitor is calibrated with Spyder 3. Gamma 2.2, 6500K, 83 cd/m^2. Contrast at 50%; brightness about 52%. My monitor lets me choose blackness level - it defaults to 50%.
    When I print the test image I linked to above, using Lightroom, with no adjustments, my technical output is as follows:
    Middle step wedge shows twelve disticnt steps. Whitest step is color of unprinted paper.
    It varies from paper to paper, but I can discerne at least the 252 step and on some papers 253 - telling me I have good highlight detail.
    On the black side I discerne 8 or 10, nothing lower. (That sounds like what you are reporting).
    Artistically I am very happy how my print looks - nice red strawberries, good flesh tones, etc.
    One my monitor, the on-screen image is almost identical to the print. I am surprised that you can see the 2 wedge step on screen at a very similar brightness.
    I also checked out this B&W test image:
    http://www.northlight-images.co.uk/article_pages/bw_printing/bw-test-image-2.html
    You are probably aware of this since you are printing with Print Studio Pro, but others may not be.
    You can print a series of test images:
    find the one that best suits your taste, enter the calibration values in PSP, and save them as a custom setting. Then, each time you want to print recall the setting.
    You can do a similar thing in Lightroom using the printer driver and User Templates.
    There would be some one-time trial and error to that approach.
    John Hoffman
    Conway, NH
    1D Mark IV, Rebel T5i, Pixma PRO-100, MX472

  • Pixma Pro 100 printing setup error

    I'm new to printing, I just got my Pixma Pro and so far have had terrible results.  1/10 times I get beautiful prints, the rest are terrible, washed out and like they have a grey film on them.  I think its either a colour management or paper management issue. I'm trying to use 8.5 x 11 " Canon Pixma Photo Paper with Matte finish.  I'm printing with Photoshop. I have the same problem whether I click on Photoshop handle colour or Printer handle colour, but the 1/10 nice prints were acheived manually setting the paper to "glossy" under the print settings menu in Photoshop CS6 rather than selecting Matte which is what the obvious choice is.  
    When I chose Photoshop handles colour management I get the same grey prints no matter what Printer Profile I select. Though it seems most logical to chose Matte Canon Pro - 100 <LU>  3 Photopaper because thats what I'm using, again the 1/10 nice prints were acheived selecting Photopaper Pro 3 <PT> Platinum.  
    I don't understand how any of this works.  The picture I am trying to print is here, nice blues and greens. http://www.flickr.com/photos/27816471@N06/9076033417/in/set-72157634198994950 it just looks grey and washed out when I print, sort of like the printer is 1/2 out of ink but it says its not.  Blacks and greys are good.
    what do I do?  I know its operator error but I can't re-produce any of the environment to get decent prints from this so i'm considering junking or returning. really dissapointed.
    Solved!
    Go to Solution.

    It is very difficult to determine which side of the matte paper is the printing side.
    Before you decide you have printer/printing problem get some glossy photo paper and try with that.
    John Hoffman
    Conway, NH
    1D Mark IV, Rebel T5i, Pixma PRO-100, MX472

  • How can I disable the low ink warning messages.

    How can I disable the low ink warning messages.  The Photosmart Plus B210 printer is connected wirelessly to my Mac over a home network..

    Open up a terminal (use spotlight to search for 'terminal')
    Find the process ID of the HP Device monitor by doing 
    ps -eo pid,command | grep "HP Device Monitor"
    The process id will be the number that is printed. Sometimes you may see two results, the correct result to use should print "/Library/Printers/hp/hpio/HP Device Monitor.app/Contents/MacOS/HP Device Monitor"
    Then using the number you got from the first step, run the following command.
    sudo kill -9 <pid>; sudo rm -rf "/Library/Printers/hp/hpio/HP Device Monitor.app/Contents/MacOS/HP Device Monitor"
    You will be prompted for your admin password.
    Below is an example of when I ran it:
    John-MacBook-Pro:~ john$ ps -eo pid,command | grep "HP Device Monitor"
    90509   /Library/Printers/hp/hpio/HP Device Monitor.app/Contents/MacOS/HP Device Monitor
    90513 grep "HP Device Monitor"
    John-MacBook-Pro:~ john$ sudo kill -9 90509; sudo rm -rf "/Library/Printers/hp/hpio/HP Device Monitor.app/Contents/MacOS/HP Device Monitor"

  • Pixma Pro-100 archival qualities

    I am interested in the archival qualities of the photos printed from a Canon Pixma Pro-100 using Canon inks and photo papers.  Are test results available?

    With genuine Canon photo paper it'll be: 20 years in open air, 30 years in a glass frame and 300 years in an archival photo album.

  • I purchased a Pixma Pro-100. My prints do not reflect the edited images from CS6/LR5.

    I just got a Canon Pixma Pro-100 printer. I'm running CS6 and LR5. My monitors are calibrated, my color space is Adobe RGB (1998). I want the Photoshop /LR to manage my color. I (believe) am using the correct profile for the Canon paper (Pro Luster). However, my prints do not reflect the edited versions I am viewing on my monitors. The colors are darker, dull, a bit on the reddish side, and not as vivid as what I am expecting. Is there anyone out there who can guide me to the proper way to set the up my printer and color space? I this is very confusing to me.

    You don't need any additional gadgets to set up your monitor(s) and the printer.  Mostly you will just frustrate yourself and waste a lot of ink and paper.  Stop wasting your time with them, too.
    You do need to get three things set carefully.  You need the brightness, the contrast and the grey-scale set right for the printer.
    Big point to remember you are dealing with two completely different types of color.  One is light and the other is dyes.  They will never match exactly except for maybe one or two colors at a time.  I generally shoot for flesh tones as that is what people notice mostly.
    Always check the details and never let the printer do any color managing.  All Canon printers I have worked with have a reddish bias.  You can not or at least it is very difficult to get rid of it.  Canon engineers seem to prefer a warm tone in their printers.
    I curently use three of the Canon Pro printers form the 9000, 9500 II amd the 100.  All are great printers.  But right now what you are seeing and what you are sending to the printer is different.  These need to match or you need to know what to adjust in PS to make them match.  Don't use LR to print, it isn't as good as PS and it will be different.  If you must, stick to either/or but not both.   I prefer PS.
    Always shoot RAW and use ACR to convert in either LR or PS but I always print from PS.
    Let me know how you get along.
    EOS 1Ds Mk III, EOS 1D Mk IV, EF 50mm f1.2 L, EF 24-70mm f2.8 L,
    EF 85mm f1.2 L II USM, EF 70-200mm f2.8 L IS II,
    Sigma 120-300mm f2.8 EX APO, Photoshop CS6, ACR 9, Lightroom 6

  • My Canon pixma pro 100 is having trouble installing its rear driver? any suggestions?- ty

    When I instal the softwear; I get a warning that I belive is linked to my problem. It is the only indicator of a problem with my printer use. I have download the driver directly from the site with no improvment- see below.

    I have the Pixma Pro-100. But I'm using Windows 7, so I'm afraid I can't be a lot of help to you. I tried to help someone in another forum the other day and showed some screenshots, but he said he didn't have anything like that on the Mac.
    If you're going to use ICC profiles, you have to turn off color management either in the printer or in the printer driver. It doesn't matter which one, just make sure that it gets turned off. Then what I do is I use soft proofing with the appropriate paper profile to prepare a soft proof copy for printing. After I have set my printer settings the way I want them and have everything just right in Lightroom, I save the preset for printing. And it seems to keep what I have set. If you can show me some screenshots of your printer driver, perhaps I can be of assistance.
    Regardless of whether I allow Lightroom to manage the color or allow the printer to manage it, I am getting really nice prints. So I'm sure there's something that you are probably just overlooking.

  • Pixma Pro-100 Leaving Smudges/Streaks on last part of 13x19" print

    Hi guys, I am in desperate need of help as I have several customer orders that I can't fulfill because my printer just stopped functioning correctly today. I have a Pixma Pro-100, and I have printed several hundred 13x19" prints with it. Today, it started adding black smudges/streaks on either side of the last few inches of every 13x19" print. I cleaned the printhead, aligned it, cleaned the nozzles, and even took the printhead out and cleaned it using the "soak in shallow water" method, before letting it dry completely. It still produces the same black smudges/streaks on either side of the last few inches of the prints.  When I remove the printhead after a print, I can notice what looks like black ink build up all around the bottom brown part where the ink sprays out from the printhead. I've tried wiping it off with an alcohol wipe and reinstalling the printhead. Nothing seems to work.  I should also note that the sponge that soaks up excess ink inside the printer seems to be really full of wet ink. I tried soaking up as much as I could with paper towels and got quite a lot of it out of there. It seems to me that this couldn't be the problem, though, because the smudges are on the printed side of the paper and not the rear side. Can anyone help me, please? 

    I have the same general problem. I have performed the roller cleaning several times, the bottom plate cleaning maybe 30 times with various weights of paper, I have ink streaks and excessive ink on prints of about  3/16" x 2-3" streaks x 3 to 4 of them groued in upper left corner, and misc spots. I recently chnaged ink cartdriges (canon) becasue the black was not printing correctly. So I repalced all of them and now the splotches/streaks occur. 

  • PIXMA Pro-100 and Windows 8.1 Help Please....

    Hello,
    I will try to be concise
    Spent all day on the phone for this without the same answer twice *sigh*.
    I have been told and I have read over and over that YES, the Pro-100 WILL absolutely work with Windows 8.1.
    Then...I find out that it's possible that it will NOT work unless I have 8.1 Pro Pack.
    Is this true?
    IOW...Is there anyone using the PIXMA Pro-100 with Windows 8.1 *without *Pro Pack just fine?
    I ordered the printer yesterday before being told about this, and need to know if I have to cancel my order before it ships.
    Thank you very much for any and all help.
    Sherri
    Solved!
    Go to Solution.

    Sherri,
    I have been using the Pro-100 along with three of the printers it has replaced, the 9000, 9500 and 9500 II since Win 8.1 came out.  They all work and work well with WIndoze 8 or 8.1.  I use Photoshop and Lightroom so the OS really doesn't matter.  If you do not have either of these, I will suggest you check into Photoshop Elements as an option.
    With one of these mentioned programs you do not need any thing additional.  Including the Canon software that comes with the Pro-100.  But a couple of Canon's software is pretty good like the printing on a DVD.  But PS, or PSE, is where it at for photos that are possibile by the Pro-100.
    EOS 1Ds Mk III, EOS 1D Mk IV, EF 50mm f1.2 L, EF 24-70mm f2.8 L,
    EF 85mm f1.2 L II USM, EF 70-200mm f2.8 L IS II,
    Sigma 120-300mm f2.8 EX APO, Photoshop CS6, ACR 9, Lightroom 6

Maybe you are looking for