Play audio on CTI Port

I'm trying to play an audio when I call a CTI Port.
I'm sending the audio to 127.0.0.1 in the port 23456 with AVTransmit (It works well with RTPRX).
I registered my application with terminal.register (InetAddress.getLocalHost(), 22222, caps);
My CTI port answers the call and receive CiscoRTPOutputStartedEv event, but I hear nothing.
Am I missing something? Do I need to do something else in my observers?
Thanks in Advance.
Jose Padilla.

Wneh you get your CiscoRTPOutputStartedEv, you need to get the CiscoRTPProperties from it. Then call getRemoteAddress() and getRemotePort(). One of them will be the address and port you need to send your RTP to.
I'm surprised that sending your RTP stream to the loopback port actually does anything ...

Similar Messages

Multiple MoH files IPCC CTI Ports

Is there a way to specify which MoH file to play within the IPCC script?
I need to be able to Accept the call and while searching for an Agent play a ringback wave file. After a predetermined amount of time play a recorded message which can just be a step in the scipt, but I then need to play a different MoH file with actual music.
I know that I can change the MoH for all CTI ports associated with IPCC but have not figure out a way to change the MoH file that is supposed to be played depending on what point in the script the call is at. Thank you in advance.
Ryan

I may not be following you here, but I will try.
If I follow, you are looking to do the following:
1. Accept call
2. Play ringback (using moh)
3. Do some workflow
4. Play message (using play prompt)
5. Play music on hold using the CUCM MoH server and audio source file
If this is indeed your script flow, then you may consider the following:
1. Accept call
2. Start ring back loop:
:RingbackLoop
play prompt "ringback"
do some workflow (item 3 from above)
if goto NextStep
Delay sec
goto RingbackLoop
:NextStep
play prompt "message"
queue caller
Call Hold (this will engage CUCM MoH)
etc.
HTH.
Regards,
Bill
Please remember to rate helpful posts.

No Audio or USB Ports after Recovery on Satellite L505D-S5983

I have recently done a system recovery with disks I created when I originally got my Satellite L505D-S5983. Which put the laptop back to an "out of the box" state...supposedly... I have been asking on a Microsoft forum for help with my problems, with limited luck.... It is still not working. I'm pasting my original posts here hoping that maybe somebody on here can help me.
POST 1:
My Toshiba Satellite L505D is running 32-bit Windows 7 Home Premium. After about 4 months of downtime I recently started it back up. There were roughly 37 updates to install when I turned it on, as expected. The updates were downloaded and installed, but when the system was restarted the system froze as soon as the desktop loaded. I booted multiple times and every time it completely freezes immediately after start up. I am not even able to open the task manager (ctrl+alt+del). They system boots perfectly fine in safe mode, and I ran what diagnostics I could find and nothing shows up....according to Windows everything is fine.
After Going through this multiple times, I got sick of it and decided to do a system recovery. Not a system RESTORE...it was a system RECOVERY. The HDD was completely wiped, and the system was supposedly returned to its original form as it was out of the box. Getting my hopes up as it finished its process... The system worked fine through the initial setup (language, time, etc.) and then as soon as the desktop loaded it froze again!
So here I am with a completely wiped HDD (except for the factory toshiba software), and a Windows OS that will only work in safe mode... I would like to avoid reinstalling Windows, I don't have any disks or anything. So any help would be appreciated
P.S. let me elaborate on what I mean by "froze". The system is completely non-responsive. No cursor movement at all, touchpad, keyboard, USB ports, nothing. When I did the restore the cursor, touchpad and keyboard worked through the initial settings only. Even when the desktop is loading i get movement for a second or two before everything freezes.
REPLY I RECIEVED:
Hi,
Since the computer is working in safe mode, I would suggest you to start the computer in clean boot to check which third party program is causing the issue. To configure your computer to clean boot follow the link
http://support.microsoft.com/kb/929135
Note: After you have finished troubleshooting, follow step 7 in the article to boot to normal startup.
If the issue does not persist in clean boot then refer ‘Step 3’, ‘step 4’ and ‘step 5’ from the following link to narrow done the issue and find out which service or startup item is causing the issue.
MY RESPONSE POSTING MY CURRENT ISSUE:
Thank you, and yes that's exactly what it was. It turned out to be an ATI program for my AMD graphics card that was not installed properly. It makes me wonder if I had to do the recovery in the first place lol.
However now I have a whole other issue. Windows is now telling me that "No audio output device is installed".....
In device manager the yellow "!" is there (High Definition Audio Controller), it tells me that it is not working....yet it says that the best drivers are installed! So yeah...I have no audio now. The only info windows gives me for the sound card is that it from Microsoft... with a driver version of 6.1.7601.17514....which naturally doesn't really help me since I have no idea what card or mobo I have . Is there any way for me to find out what I need other than opening up my laptop?
//--> Toshiba Satellite L505D-S5983_AMD Athlon II Dual-Core M300 2.00 GHz_3GB RAM 32-bit OS   <--//
RESPONSE FROM SOMEBODY ELSE:
Hi,
Check with Toshiba Support, their on-line documentation and drivers, and ask in their
forums about known issues.
Toshiba - Forums
http://laptopforums.toshiba.com/
Toshiba - Contacts
http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/navShell.jsp?cf=su_contact
Toshiba - Drivers - navigate to your model
http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/home.jsp?nav=Download
Toshiba - Support
http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/home.jsp
========================================
First run SFC /scannow and checkdisk (chkdsk) as the cause of these issues might
be some sort of corruption.
Start - type in Search box - CMD   find at top of list - RIGHT CLICK - RUN AS ADMIN
sfc /scannow
How to Repair Windows 7 System Files with System File Checker
http://www.sevenforums.com/tutorials/1538-sfc-scannow-command-system-file-checker.html
Then run checkdisk (chkdsk).
How to Run Disk Check in Windows 7
http://www.sevenforums.com/tutorials/433-disk-check.html
Then use this troubleshooter :
References to Vista also apply to Windows.
Fixing a customer problem: “No Audio Device is Installed” when launching sndvol on Windows Vista
http://blogs.msdn.com/b/larryosterman/archive/2009/01/06/fixing-a-customer-problem-no-audio-device-i...
Also update or re-install the driver.
Control Panel - Device Manager - SOUNDS - look for HD Audio - Mine says RealTek High
Definition Audio (that is an example and yours may have an entirely different name/maker).
Write down description make and model - double click on it - drivers tab - write down version.
Now Click UPdate Drivers which may not do anything as MS is far behind certifying drivers.
Then RIGHT CLICK on it and UNINSTALL - REBOOT - this will rebuild the driver stack.
1st go to system maker's site and look for latest driver Download - SAVE - go to right click on
and RUN AS ADMIN (This is your fallback.) REBOOT after each driver installation.
NOTE : Sound drivers often rollback so check the version after installation and the
reboot to see if the version you installed is there, if not repeat the install - reboot
until it is. It can take several tries depending on how many rollbacks it does.
Then do same for Device Maker's site.
Manually look at manufacturer's sites for drivers - and Device Maker's sites.
http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm
Installing and updating drivers in Windows 7 (updating drivers manually using the methods above
is preferred to ensure the latest drivers from System maker and Device makers are found)
http://www.sevenforums.com/tutorials/43216-installing-updating-drivers-7-a.html
Error “the Audio Service Is Not Running” When Opening the Volume Mixer in Vista
http://www.winhelponline.com/blog/error-the-audio-service-is-not-running-when-opening-the-volume-mix...
Also Right Click Speaker near clock - Playback Devices - right click in the box area -
check Show disable and disconnected devices. Highlight speaker and on the lower
Right click Properties check settings for Device Usage enabled and so on. Also do
same for Configure on Lower Left of that box.
In Control Panel you can also look for an Audio Manager along with the Sound Settings.
Open the Playing Audio troubleshooter
http://windows.microsoft.com/en-us/windows7/Open-the-Playing-Audio-troubleshooter
Problems with sound and audio or no sound - a Mr Fixit
http://support.microsoft.com/gp/no_sound
No sound in Windows
http://windows.microsoft.com/en-us/windows/help/no-sound-in-windows
Tips for fixing common sound problems
http://windows.microsoft.com/en-us/windows7/Tips-for-fixing-common-sound-problems
Speakers and other audio output devices
http://windowshelp.microsoft.com/Windows/en-US/Help/a43f3a31-6d9f-49d1-be22-e2f47b8b1f2c1033.mspx
How to Enable Hidden Audio Devices in Vista
http://www.vistax64.com/tutorials/143447-audio-device-enable-hidden-devices.html
Hope this helps.
===========================================================================================
Ok...so I have installed all of the appropriate drivers that I thought I may need from this website. I have tried ALL of those system analysis programs that were suggested. Every one of them lists my mobo simply as a Toshiba motherboard, with no audio card information. Which I'm assuming that is because it has an internal sound processor. My problem is that none of the properties, or ANYTHING I try, will give me information on what I need to fix this...
I would be more than willing to run the recovery again if I knew that I had everything I actually need... When I created my original recovery disks it created a third disk with "apps and drivers". I installed all of them...and still here I am... And I haven't even STARTED on my USB port issue yet...those don't work either, and they don't even show up in my Device Manager...sigh...
And please, a response that doesn't look like an automated response to try and sell software like the last one I recieved from the Microsoft forum would be appreciated
Thank you for your time, and apologies for the lengthy post, but I wanted to provide as much info as possible.

Satellite L505D-S5983
I would try another restore of the hard disk to its original out-of-the-box contents using Toshiba recovery media. Maybe something went wrong in the process. Make sure everything works before applying any updates and adding any hardware or software.
Then add things carefully, rebooting Windows and testing the USB and audio at each step.
Please note this.
The only info windows gives me for the sound card is that it from Microsoft... with a driver version of 6.1.7601.17514....which naturally doesn't really help me since I have no idea what card or mobo I have . Is there any way for me to find out what I need other than opening up my laptop?
Every one of them lists my mobo simply as a Toshiba motherboard, with no audio card information. Which I'm assuming that is because it has an internal sound processor. My problem is that none of the properties, or ANYTHING I try, will give me information on what I need to fix this...
All of the latest drivers for your model are easily found here. This one is for the sound.
   Realtek Audio Driver for Windows 7 (32/64)
-Jerry

Audio line-in port stopped working properly

I started to have a perplexing problem that I narrowed down to the audio in-put port on my Mac Pro (MacPro3,1). It was working fine then the sound level increased and the quality became distorted (like a "fuzz base" but affecting all sounds).
I was in the process of digitizing records, and believed the record played broke. So I got a new record player (audio-technica AT-LP120-USB). The same thing occurred with the audio in-put port, so I switched to the USB port and the audio was fine. I also checked with music already on my HD and it played fine. Consequently it has to be the in-put line port and/or a software issue.
I checked BBs but could not find a similar issue.
Any suggestion? Thanks in advance.

Since this is a Mac Pro question I'll request this be moved to the Mac Pro forum. You posted in the PowerMac forum which is pre-Intel Macs.

How do I play audio attachment in my PDF file?

How do I play the audio attachment in my PDF files in android?

Hey thanks, after an hour with Apple, the tech had me reset the phone and it worked perfectly.
Sent from Windows Mail
From: Apple Support Communities Updates
Sent: Sunday, October 12, 2014 11:52 AM
To: jamesfrombend
You received a reply
Ralph9430 has replied to your question. You can view the full discussion in Apple Support Communities.
How do I play audio books in my car using USB cord?
Does the sound system on your car have a usb input? If so connect your iPhone to the radio with your cable and play the audio book on your phone. Note that your vehicle needs to be able to accept audio input through thr USB port and not just provide a charging circuit. Check your vehicle's manual if you are not sure.
Correct Answer Helpful Answer
Use the buttons above to tell Ralph9430 and the rest of the community if this reply solved your question or helped you get closer to finding a solution.
To reply to Ralph9430, go to the discussion in Apple Support Communities.
You are receiving this email from Apple Support Communities. You can change your email preferences in your Apple Support Communities Profile.
TM and copyright © 2014 Apple Inc. 1 Infinite Loop, MS 96-DM. Cupertino, CA 95014.
All Rights Reserved | Privacy Policy | Terms of Use | Apple Support

Synchronization problem MoH in CTI port

Hi
I have a problem with the synchronization of User Hold Audio Source and Network Hold Audio Source in the CTI Ports. The callmanager cluster is 6.0.1.2121-1 and UCCX 5 versio.
After doing a Data Resync the result is User Hold Audio Source-- UUID changed from {AC0250B0-6F23-4D91-A73B-A733B011C5CE} to {31E8EA9C-57832-43F7-8384-4C6351A97110}.
Attached is a picture about the result of Data Resync process.
Thanks in advance.
Regards.

MOH issues can be tricky, but let's start with a couple of assumptions:
1. You are running a single CCM cluster
2. The callers coming into the UCCX system are all using the same MRGL
3. If you're using Multicast for MOH, then you have multicast properly set up.
4. You have the MOH audio source files loaded on all the servers where it needs to be (must be loaded on each MOH server individually, these do NOT replicate).
I make the above statements because if any of the above are not true, you can have issues, and while they may manifest on UCCX, they are not UCCX problems.
If you have the data resync/check coming up clean, and it's still misbehaving, open up the call control groups and make some small modification to them...change the description or something so that it will delete all the ports and then rebuild them. Make sure you open up the more info and confirm the settings are where you want them to be. The existing ports will get deleted and then rebuilt. This will resolve any issue where someone modified something directly on CCM that could potentially cause your issue.

SIP trunk call to CTI port media endpoint problem

Hi, I have the following scenario:
CUCM ---SIP-----CUBE----SIP----ITSP
CUCM cluster has two servers 10.1.9.5 and 10.1.9.6 (subscriber), we have a CTI application running on 10.1.9.8, we got a bunch of SIP DIDs from ITSP and those SIP DID numbers are mapped to CUCM internal DNs on CUBE through translation, inbound SIP calls to mapped SCCP phones work fine, media stream of internal call leg is established directly between SCCP phone and CUBE as expected. However, when inbound SIP calls to the number which maps to CTI extention, there is no audio, debug on CUBE shows that the media stream of internal call leg is between one of the CUCM servers. I want to understand why CUCM is telling CUBE to use the IP address which is NOT CTI port is registered from (in this case 10.1.9.8)? why would CUCM treat a CTI extention differently from a regular SCCP phone extension. For regular inbound call to SCCP phones codec between CUCM-CUBE and between CUBE-ITSP are both g11ulaw.
Thanks,

"debug on CUBE shows that the media stream of internal call leg is between one of the CUCM servers" ==>
debug on CUBE shows that the media stream of internal call leg is between 10.1.9.5 (happens to be MTP) and CUBE

I'm running Mavericks 10.9.3, updated iTunes earlier today, but although I can play audio CDs, DVDs will not play, any suggestions?

I'm running Mavericks 10.9.3, updated iTunes earlier today, but although I can play audio CDs, DVDs will not play, any suggestions?

Hello there, tomazdes.
The following Knowledge Base article written for the USB SuperDrive, offers some practical steps to try when issues present themselves with particular content playback (feel free to skip Step 3 when working with an iMac or MacBook with built-in drives):
Apple Computers: Troubleshooting the slot-loading SuperDrive
http://support.apple.com/kb/HT2801
Particularly:
Accepts discs but they don't mount or are automatically ejected
Make sure the drive is not placed upside down. The aluminum enclosure should be facing up as shown in section 1.
Check the disc's surface for scratches and dirt, since these things can prevent the disc from appearing on the desktop.
Connect the MacBook Air SuperDrive directly to the computer's USB port instead a USB hub.
Reset the System Management Controller (SMC).
Ensure your drive can read the specific type of disc being used. The System Profiler or System Information may provide additional information regarding what media your computer supports.
OS X Snow Leopard v10.6 or earlier: Open Apple System Profiler by choosing "About this Mac" from the Apple () menu. Then, click More Info.
OS X Lion v10.7 and later: Click the Apple () menu and then hold down the Option key. Choose System Information from the menu.
If the disc continues to not be recognized, contact Apple or an Apple Authorized Service Provider, or make an appointment with an Apple Retail Store.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

I have just got a iPod 5 gen 32gb and lightning adapter but can't get it to work with my docking station it will charge but not play audio please help??

I have bought a 5th gen iPod and lightning adapter but it won't wrk on my docking station it charges but doesn't play audio? Please help

Does the dock manufacture say it is compatible with the 5G iPod with iOS 6.0.1?
Have you went to the manufacturer's support site? Contacted them?
Try resetting the dock. How you do that depends upon the dock
Sometimes this works
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.

When i try to upload a .mts file from my Sony camera to Premiere Pro CC it refuses to play the audio! Ofcourse i could convert every single clip but it takes tons of time. How can i make Pr play audio track properly?

When i try to upload a .mts file from my Sony camera to Premiere Pro CC it refuses to play the audio! Ofcourse i could convert every single clip but it takes tons of time. How can i make Pr play audio track properly?

Does it not play at all or cannot you get the audio in the timeline?
Did you copy the entire card to the hdd and then imported the file via the Media Browser?
Did you source patch the audio tracks?

How can I code to play audio continuously from page to page in iBooks for reflow ePub

Hi,
I have tried and successfully completed the iBooks ambient soundtrack option in Fixed Layout ePub. It works fine.
But while trying the same in Reflow ePub, it is not working in iPad iBooks. I have latest iBooks version and latest iOS version in my iPad.
Please let me know how can I code to play audio continuously from page to page in iBooks for reflow ePub?
Thanks,
Sundaram

As soon as the user turns to the next page, the audio stops.
That's how it works in all cases.
the book is a read aloud book.
See the 'How-To Read Aloud' section in iBA Tips and Tricks 01

Satellite L-50 can't play audio from multiple sources

I can't play audio from multiple sources. This is very annoying when I have 2 youtube videos playing, if I start playing something on the media player, there is no sound on media player, it's the same when I have 2 media players open and 1 youtube video playing, youtube video doesn't have sound..
I already have all the latest drivers, last DTS driver update was in 2014, sound update this year's february..
25/02/14
DTS Studio Sound
DTS Inc.
Windows 8.1 - 64 Bit
1.01.2700
I don't know if this makes sense, but I got newer DTS sound driver which I found, It's not my laptop model, but they all seem to be the same - v1.1.88.0
I uninstalled DTS software and still had the same problem, so it's not affecting sound driver in any way..
10/02/15
Sound Driver
Integrated Device Technology Inc.
Windows 8.1 - 64 Bit
6.10.6491.0
IDT audio driver has newer release date, but the driver version is the same as the 2013 one..
Why are toshiba releaseing old driver as 'NEW' ?
2nd is my speakers advanced settings, nothing changed when I disabled "Allow applications to take exclusive control of this device"
Attachments:
audio.png ‏6 KB
test2.png ‏7 KB
specs.png ‏16 KB

Can you check the full model and part number from the laptop?
- Peter

Can't play audio cd in totem

hello!
the subject says all. when i insert an audio cd into my drive i can't play it with totem (totem-xine). the option "play audio cd" is greyed out.
any ideas?
mfg iggy

Are you a member of the optical group.

Satellite L50-A-19N can't play audio from multiple sources

I can't play audio from multiple sources. This is very annoying when I have 2 youtube videos playing, if I start playing something on the media player, there is no sound on media player, it's the same when I have 2 media players open and 1 youtube video playing, youtube video doesn't have sound..
It goes away when I plug out my headphones..
I already have all the latest drivers, last DTS driver update was in 2014, sound update this year's february..
25/02/14
DTS Studio Sound
DTS Inc.
Windows 8.1 - 64 Bit
1.01.2700
I don't know if this makes sense, but I got newer DTS sound driver which I found, It's not my laptop model, but they all seem to be the same - v1.1.88.0
I uninstalled DTS software and still had the same problem, so it's not affecting sound driver in any way..
10/02/15
Sound Driver
Integrated Device Technology Inc.
Windows 8.1 - 64 Bit
6.10.6491.0
IDT audio driver has newer release date, but the driver version is the same as the 2013 one..
Why are toshiba releaseing old driver as 'NEW' ?
2nd is my speakers advanced settings, nothing changed when I disabled "Allow applications to take exclusive control of this device"

I see that the option called “give exclusive mode applications priority” has been checked.
Usually different applications and programs can access the sound card simultaneously.
For example: you can hear the sound in game, while you can run your own music via an external player.
This is prevented with these options “give exclusive mode applications priority”.
Maybe you should disable (uncheck) this option to prevent the different applications for using this exclusive mode stream.
I did it for my DAC. I set the DAC for exclusive mode. Once my audio playback software starts to play music, no other software is able to share the DAC.
However, I use Win 7 and Realtek sound driver… It’s another configuration.
So it’s not known to me if your issue is related Win 8.1 system or maybe limitation of sound driver… it could be also possible that one of your sound applications don’t allow multiple sound streaming.

Can I use Optical Audio alongside a speakerless monitor to play audio through speakers?

I have an Apple TV 3 and so far I am relatively pleased. However.. I have no sound, this just about renders my Apple TV useless. Is it possible to use the Optical Audio cable to play sound from films, music etc. while still having the Apple TV connected to the Monitor via HDMI? Do you have any suggestions as to what speakers would be good? (looking at around £50 - £100) I was thinking of getting some of the Bose Companion 2 monitor speakers and then using a DAC to play audio from the Apple TV to the speakers. Would this work? If not, does anybody have any other suggestions?
P.S. I can't plug speakers into my monitor for some absurd, annoying reason unbeknown to society

My ATV is connected to the tv with hdmi
My optical is connected to my stereo
I mute my tv and only play out of the stereo

Play audio on CTI Port

Similar Messages

Maybe you are looking for