Please help, g5 won't go past grey "start-up" screen

Apologies if there is a better forum for this question:
G5 doesn't get past the light grey start-up screen now, and after a while the fans begin to slowly ramp up in speed until they reach maximum. Problems began when in Itunes the machine locked up totally, mouse wouldn't work nor keyboard. I have unplugged power cord and waited various amounts of time, reset the PRAM, and replace the system clock battery.
Not sure what to do next, Apple Service?
Thanks in advance!
Larry

Problem solved! Luckily this one didn't require a visit to a service center. Here's what worked.
At power on, launched open firmware (command option o and f)
ejected disc tray with "eject disc", put in OS X.
at this point I actually had to re-power up the computer because I then typed "mac-boot" and of course got the same problem.
On power up, held down C, joy of joys machine booted from disc!
Opened disk utility and checked my boot volume for errors, tested okay.
Checked the logs and found unusual "bootsrap....unkown error code".
figured, well i've gone this far, repaired disc permissions as well, found quite a few permission errors (had been a while since I last repaired).
Closed disk utility and restarted from boot volume.
TA-DA!
At some point, I reset the PMU with a button push on the inside of the machine, which didn't apparently do anything, bacause the machine didn't boot after i did that.
I also had replaced the system clock battery, which of course didn't fix the problem, but owing to the fact that I had experience several clock type errors previously, I most certainly needed to replace it anyway. Thanks to all who responded, especially Dale for pointing me in the direction of Mac 101 and open firmware.

Similar Messages

Mac book pro won't go past grey start up screen

Went to turn on my Mac book pro 2011 or 2012 and it went to the grey loading screen with an apple, spinning gear and a loading bar. Once the loading bar completes my Mac book just turns off. It just keeps doing this, I tried to do a safe boot, but once it was done that it turned off and continues to do this circle of grey screen loading than turning off. Please help!

Hi ANaomi,
If you are having issues with your MacBook Pro not booting past a grey screen, and/or shutting down during the boot process, you may find the troubleshooting steps outlined in the following articles helpful:
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/TS2570
OS X: When your computer spontaneously restarts or displays "Your computer restarted because of a problem."
http://support.apple.com/kb/HT200553
Regards,
- Brenden

Won't boot past grey start up screen.

All of a sudden my Itunes quit and wouldn't reopen so I thought a restart would be the fix. It turned back on but then got stuck on the grey loading screen. I tried all the hold down button combos and nothing worked. I am out of warranty and am a poor college student. Any advice? Please help.

Welcome to the Apple discussions.
You'll need the original OS X discs that came with your system. Insert the first one, and boot holding the C key down, which will boot from the OS X disc. From the menu bar, choose disk utility and repair permissions and repair disk. Any messages on repair disk? If it concludes successfully, reboot. Working now?
If not, you should run the Apple hardware test. Insert the OS X disc that has 'AHT Version x.x' in small print on the label. Reboot holding the option key down, choose Apple hardware test, click the arrow pointing to the right, and follow directions. If prompted, choose the extended test. Does this give you any messages? Note, if you have either of the TechTool programs, they can do the same testing.
Post back the results and we can help further from there.

Computer won't get past grey start up screen after install

Okay - I made a stupid mistake. I started the installation process - it was taking a very long time so I decided to quit and free up some more space before trying again. When I quit it wouldn't let me go back to my old version - I think I was on 10.3.9. So I installed 10.5 - and it said it installed successfully. I restarted and the computer won't get past the gray screen. I let it go for 30 minute the first time, 15 the second time, and about an hour the third time. Won't go any futher. Any ideas?
Thanks,
-Brad

same thing happened to me (you need to read all the posts as someone will have had the exact problem as you).
any way,
1. re-installl 10.5 from your leopard disk. (put disk in restart holding c key down etc). do not install OS just yet.
2. run disk utility (it does not hurt-click on options button)- repair both disk and permissions
3. run 10.5 installer (archive)
4. download 10.5.2 combo from apple (that is if you can easily find it!)
5. run that install
6 it will restart two or so times
7. total time is 20 mins or so. most of that is in repairs form #2.

My Macbook won't get past the start up screen

Hey everyone
I have a Macbook that's about 3 years old. I did an software update yesterday and since doing it the computer won't get past the start up screen. There's just the Apple logo and the rolling ball thing. It's been stuck there for around 30mins and nothing changes. I'm not really sure what has happened but I was wondering if there is any way I can fix it.
Thanks for your time.
Bevan

Hey Lyssa
I don't have a back up but I'm not to worried about that as it's my traveling computer and I only use it for the web and some word processing.
I don't have the disks with me right now as I'm away from home. I'm not sure what I had updated, I think there was a lot because I hadn't don't it in a long time.
If I can start it in safe mode what should I do?
Thanks.
Bevan

MBP won't boot past grey spinning gear screen

I tried to turn on my computer the other day, it turns out it wont boot up past the grey spinning gear screen.
First thing I did was reboot from SL install disk, I ran disk utility and tried to verify and repair my HD, both came back with errors... uh oh
I then tried to back up the hard drive by creating a new disk image of my HD and placing it on my USB external, came up with and I/O error... oh sh*t
I tried reinstalling snow leopard and it could not be installed... F*CK!
I tried starting it up single single user mode to see what was happening, turns out it get to the line "dis0s2: I/O error blah blah blah" and then keeps iterating it indefinalty, leading me to believe my hard drive is dead or dying.
so now for the question:
Is it still possible to backup my hard drive in this state? I know, I know, should've been backing it up all along but I'm stupid and didn't. I don't really care about my user setting or anything like that but I use this computer for college and have tons of documents on it that I need.
Also my applecare has expired so i would like to stay away from those genious bartenders.
Any suggestions?

If you have access to another Mac with Firewire then you can connect the two via Firewire cable. You can then attempt to boot your computer into Target Disk Mode. If that's successful then boot the other computer normally. If your drive is accessible it will appear on the Desktop of the other computer. It may then be possible to copy your files if the drive is at all intact. If not you may be able to use recovery software to restore your files. If the drive is not accessible even to recovery software, then you would have to send it to a business that specializes in drive recovery. These are very expensive alternatives - $500 minimally.
You can also try third-party disk repair software. The best of the lot is Disk Warrior, but if the drive has a hardware failure preventing access, then I'm afraid there's little you can do to recover your files beyond sending the drive to a data recovery service.
General File Recovery
If you stop using the drive it's possible to recover deleted files that have not been overwritten with recovery software such as Data Rescue II, File Salvage or TechTool Pro. Each of the preceding come on bootable CDs to enable usage without risk of writing more data to the hard drive.
The longer the hard drive remains in use and data are written to it, the greater the risk your deleted files will be overwritten.
Also visit The XLab FAQs and read the FAQ on Data Recovery.

I installed Lion but now my Macbook won't go past the start-up screen. Help!

I installed Mac OS X Lion today and it downloaded and installed fine but when it restarted it went to the white start up screen with the grey apple logo and the wheel kept going around for two hours. I held the power button and my macbook went off so I pushed it again and it went on, again staying at the start up screen for half an hour. I restarted it again and held the option button to boot to recovery. I then repaired the permissions and the disk drive and then reinstalled Mac OS X Lion. This time the installation took around 4 hours to complete and then restarted. It again went to the white start up screen and the grey wheel has now been going around for the last hour! What can I do? I haven't backed up my files and would still like to keep them. Thanks.

Hey Lyssa
I don't have a back up but I'm not to worried about that as it's my traveling computer and I only use it for the web and some word processing.
I don't have the disks with me right now as I'm away from home. I'm not sure what I had updated, I think there was a lot because I hadn't don't it in a long time.
If I can start it in safe mode what should I do?
Thanks.
Bevan

My Final Cut Pro X won't load past the start-up screen....Why??

I have been using FCPX for about 3 months now and I have had no problems. Out of NOWHERE today when I tried to open up FCPX it loads everything except for one project and it gets stuck. The start-up screen simply says "reading project 1". I have no idea what to do. I use FCPX everyday for editing videos and now I have nothing. I need someone's help.

Not too many fans of FCPX here. Wrong forum. You'll have better luck here. https://discussions.apple.com/community/professional_applications/final_cut_pro_ x

Help: iMac won't boot past Grey logo screen with spinning lines

My fiance's iMac (intel based) running snow leopard (upgraded from Leopard a couple months ago) will not boot past the logo and spinning lines. This started after at attempting to restart after installing updates to Safari and iTunes.
When booting in verbose mode I get these lines:
Launchctl: Dubious permissions on file (skipping): /Library/LaunchDaemons
Launchctl: Dubious permissions on file (skipping): /System/Library/LaunchDaemons
Launchctl: Dubious permissions on file (skipping): /etc/mach_inid.d
AppleYukon2: Marvel Yukon Gigabit Adapter 88E8055 Singleport Copper SA
AppleYukon2: RxRingSize <= 1024, TxRingSize 256. RXMAXLE 1024, TXMAXLE 768, STMAXLE 3328
Then it just stops and does nothing.
I've unplugged everything except the apple keyboard and mouse. Ethernet is not connected.
She doesn't seem to have the original disc that came with the computer, but I do have the Snow Leopard upgrade disc.
What do I do? It won't boot in Safe Mode either, freezes at the same spot.
I'm not a particularly savvy Mac user as I recently embraced them when we moved in together.
Any help would be greatly appreciated

Repairing permission is not the first answer. Should try to run fsck and reset the PRAM
Start up your computer in single-user mode to reach the command line.
Note: If necessary, perform a forced restart as described in the Emergency Troubleshooting Handbook that came with your computer. On desktop computers, you can do this by pressing the reset/interrupt button (if there is one) or holding down the power button for several seconds. On portable computers, simultaneously press the Command-Control-power keys. If your portable computer doesn't restart with this method, you may need to reset the Power Manager.
At the command-line prompt type:
/sbin/fsck -fy
Press Return. fsck will go through five "phases" and then return information about your disk's use and fragmentation. Once it finishes, it'll display this message if no issue is found:
** The volume (name_of_volume) appears to be OKIf fsck found issues and has altered, repaired, or fixed anything, it will display this message:
***** FILE SYSTEM WAS MODIFIED *****
Important: If this message appears, repeat the fsck command you typed in step 2 until fsck tells you that your volume appears to be OK (first-pass repairs may uncover additional issues, so this is a normal thing to do).
When fsck reports that your volume is OK, typerebootat the prompt and then press Return.
Your computer should start up normally and allow you to log in.
Resetting PRAM and NVRAM
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
Your computer's PRAM and the NVRAM are reset to the default values. The clock settings may be reset to a default date on some models.

IMac won't get passed grey start up screen following power cut?

Hi,
I was working on a Word document when we had a power cut yesterday afternoon. They then said it was OK, the power came back on and I stupidly believed them and turned the iMac back on.
Within second, just as it got the grey screen with the Apple sign and little grey wheel, the power went again. It has been back all night, so have tried to get it started this morning and although it starts with the little tune and goes to the grey screen with the Apple sign and little wheel, after an hour nothing more?
I powered down and tried again holding down the Shift key as I started, but it the same, little grey wheel nothing else?
Please can anyone help me, i have just started my own business and am lost with it
Many thanks in advance.
Lynne

HI Anamusic,
Many thanks for the link I will save it, but unfortunately I have a wireless keyboard and tracker pad, so I don't think the keyboard is active when I need to use it, I have tried but it seems to be exactly the same.
Thank you for your help anyway.
Do you know if this something they might be able to fix in the 'Genius Bar' or will I have to take it to a Mac repair place?
Sorry never had problems like this before and just don't know what to do.
Lynne

Mac book won't go past the start up screen.

So my mac book pro will not go past the loading screen where you see the apple symbol and the rotating gear thing. is there anything i can do to fix this or restart my OS?

http://support.apple.com/kb/TS2570 For the part that it says to startup by your disc and run disk utility, if you're running 10.7 or 10.8 you'll actually bootup holding down Command and R on startup. Hope this helps

IBook G4 suddenly won't boot past the "booting OSX" screen.

My iBook G4 suddenly died and now won't boot past the "Starting OSX" screen. The blue bar goes all the way across but never moves to the next screen. I have my original disks, containing OS 10.4.5. I am trying to boot from the disk, but just keep getting the Installer program. When I try to choose a startup disk, it still won't start. Any help or ideas? This is urgent.
BTW, I am a photographer and was workig in PhotoShop7 -- a program I use all day, every day.

Start from the install disc again and choose Disk Utility from the menu. Highlight the drive on the left and click Repair Disk. If it reports errors and repairs made, repeat the process until no errors are reported.
John

My iMac won't boot past grey screen and it didn't come with a os x disk

My iMac won't boot past grey screen with apple. I've tried booting in safemode but that didn't help and my iMac didn't come with a os x disk.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Upgraded my iphone 4S to 8.0.2 and it won't go past the Hello startup screen or accept my Apple ID Sign in!!! Help!!! What do I do to fix this??

Upgraded my iphone 4S to 8.0.2 and it won't go past the Hello startup screen or accept my Apple ID Sign in!!! It just restarts itself!!!
Help!!! What do I do to fix this??

I doubt that your data have been lost, the hard drive should be fine. Too bad that you're going to sell it, you could have used the hard drive in an enclosure to back up your new computer to. Please remember to make frequent backups/clones, I use SuperDuper! and it works perfectly. I have used it to re-clone a drive from the external when things have gone bad, you can also boot from a SuperDuper! clone.
Anyway, let us know how things go, I'm pretty sure your drive will be fine.

My macbook air won't get past the white apple screen. I've tried power cycling the batter but won't help

my macbook air won't get past the white apple screen. I've tried power cycling the batter but won't help

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Please help, g5 won't go past grey "start-up" screen

Similar Messages

Maybe you are looking for