Port channel failure / lacp_switch_get_new_agg_id: secondary l3 agg are not supported

hi,
hope that someone can help.
I ran into port channel issue when trying to add 4 port Quantum Dxi server into a port channel in 3750 stack.
Configs looks ok:
interface Port-channel6
description qdx-server
switchport access vlan 3
switchport mode access
spanning-tree portfast
spanning-tree bpduguard enable
end
all four ports configured as follows
interface GigabitEthernet1/0/7 , 1/0/5 , 2/0/7 and 2/0/8
description qdx-server-ethx
switchport access vlan 3
switchport mode access
spanning-tree portfast
spanning-tree bpduguard enable
channel-protocol lacp
channel-group 6 mode active
end
all ports joined the channel except Gi 1/0/5 - it got suspended once joined the port channel
From the debug I got the following:
Dec 16 13:36:43.082 GMT: FEC: lacp_switch_get_new_agg_id: secondary l3 agg are not supported Po6
Dec 16 13:36:46.823 GMT: FEC: pagp_switch_agc_compatable: comparing GC values of Gi1/0/5 Gi1/0/7 flag = 1 1
Dec 16 13:36:46.823 GMT: FEC: pagp_switch_port_attrib_diff: compare LACP modes for Gi1/0/5
Dec 16 13:36:46.823 GMT: FEC: pagp_switch_port_attrib_diff: Gi1/0/5 Gi1/0/7 same
Dec 16 13:36:46.823 GMT: FEC: pagp_switch_agc_compatable: GC values are compatable
Dec 16 13:36:46.823 GMT: FEC: pagp_switch_restart_if_needed(1): Gi1/0/5 in list
Dec 16 13:36:46.823 GMT: FEC: pagp_switch_invoke_port_down: Gi1/0/5
Dec 16 13:36:46.823 GMT: FEC: pagp_switch_invoke_port_up: Gi1/0/5
Dec 16 13:36:46.823 GMT: FEC: pagp_switch_agc_compatable: comparing GC values of Gi1/0/5 Gi1/0/7 flag = 1 1
Dec 16 13:36:46.823 GMT: FEC: pagp_switch_port_attrib_diff: compare LACP modes for Gi1/0/5
Dec 16 13:36:46.823 GMT: FEC: pagp_switch_port_attrib_diff: Gi1/0/5 Gi1/0/7 same
Dec 16 13:36:46.823 GMT: FEC: pagp_switch_agc_compatable: GC values are compatable
Dec 16 13:36:46.823 GMT: FEC: lacp_switch_calculate_oper_key: oper_key for port Gi1/0/5 is 0x6
Dec 16 13:36:46.982 GMT: FEC: lacp_switch_get_first_agg_id_from_admin_oper_keys: found aggregator Po6 for admin_key [0x6] and oper_key [0x6]
Dec 16 13:36:46.982 GMT: FEC: lacp_switch_is_aggregator_valid: aggregator Po6 is still valid
Dec 16 13:36:46.982 GMT: FEC: lacp_switch_get_first_associated_port_from_agg_id: found port Gi2/0/8 associated to Po6
Dec 16 13:36:46.982 GMT: FEC: lacp_switch_is_aggregator_valid: aggregator Po6 is still valid
Dec 16 13:36:46.982 GMT: FEC: lacp_switch_get_next_agg_id_from_admin_oper_keys: aggregator next to Po6 not found for admin_key [0x6] and oper_key [0x6]
Dec 16 13:36:46.982 GMT: FEC: lacp_switch_get_new_agg_id: secondary l3 agg are not supported Po6
Dec 16 13:36:56.830 GMT: FEC: pagp_switch_agc_compatable: comparing GC values of Gi1/0/5 Gi1/0/7 flag = 1 1
Dec 16 13:36:56.830 GMT: FEC: pagp_switch_port_attrib_diff: compare LACP modes for Gi1/0/5
Dec 16 13:36:56.830 GMT: FEC: pagp_switch_port_attrib_diff: Gi1/0/5 Gi1/0/7 same
Dec 16 13:36:56.830 GMT: FEC: pagp_switch_agc_compatable: GC values are compatable
Dec 16 13:36:56.830 GMT: FEC: pagp_switch_restart_if_needed(1): Gi1/0/5 in list
Dec 16 13:36:56.830 GMT: FEC: pagp_switch_invoke_port_down: Gi1/0/5
Dec 16 13:36:56.830 GMT: FEC: pagp_switch_invoke_port_up: Gi1/0/5
Dec 16 13:36:56.830 GMT: FEC: pagp_switch_agc_compatable: comparing GC values of Gi1/0/5 Gi1/0/7 flag = 1 1
Dec 16 13:36:56.830 GMT: FEC: pagp_switch_port_attrib_diff: compare LACP modes for Gi1/0/5
Dec 16 13:36:56.830 GMT: FEC: pagp_switch_port_attrib_diff: Gi1/0/5 Gi1/0/7 same
Dec 16 13:36:56.830 GMT: FEC: pagp_switch_agc_compatable: GC values are compatable
Dec 16 13:36:56.838 GMT: FEC: lacp_switch_calculate_oper_key: oper_key for port Gi1/0/5 is 0x6
Dec 16 13:36:56.880 GMT: FEC: lacp_switch_get_first_agg_id_from_admin_oper_keys: found aggregator Po6 for admin_key [0x6] and oper_key [0x6]
Dec 16 13:36:56.880 GMT: FEC: lacp_switch_is_aggregator_valid: aggregator Po6 is still valid
Dec 16 13:36:56.880 GMT: FEC: lacp_switch_get_first_associated_port_from_agg_id: found port Gi2/0/8 associated to Po6
Dec 16 13:36:56.880 GMT: FEC: lacp_switch_is_aggregator_valid: aggregator Po6 is still valid
Dec 16 13:36:56.880 GMT: FEC: lacp_switch_get_next_agg_id_from_admin_oper_keys: aggregator next to Po6 not found for admin_key [0x6] and oper_key [0x6]
Dec 16 13:36:56.880 GMT: FEC: lacp_switch_get_new_agg_id: secondary l3 agg are not supported Po6
Dec 16 13:37:06.837 GMT: FEC: pagp_switch_agc_compatable: comparing GC values of Gi1/0/5 Gi1/0/7 flag = 1 1
Dec 16 13:37:06.837 GMT: FEC: pagp_switch_port_attrib_diff: compare LACP modes for Gi1/0/5
Dec 16 13:37:06.837 GMT: FEC: pagp_switch_port_attrib_diff: Gi1/0/5 Gi1/0/7 same
Dec 16 13:37:06.837 GMT: FEC: pagp_switch_agc_compatable: GC values are compatable
Dec 16 13:37:06.837 GMT: FEC: pagp_switch_restart_if_needed(1): Gi1/0/5 in list
Dec 16 13:37:06.837 GMT: FEC: pagp_switch_invoke_port_down: Gi1/0/5
Dec 16 13:37:06.837 GMT: FEC: pagp_switch_invoke_port_up: Gi1/0/5
Dec 16 13:37:06.837 GMT: FEC: pagp_switch_agc_compatable: comparing GC values of Gi1/0/5 Gi1/0/7 flag = 1 1
Dec 16 13:37:06.837 GMT: FEC: pagp_switch_port_attrib_diff: compare LACP modes for Gi1/0/5
Dec 16 13:37:06.837 GMT: FEC: pagp_switch_port_attrib_diff: Gi1/0/5 Gi1/0/7 same
Dec 16 13:37:06.837 GMT: FEC: pagp_switch_agc_compatable: GC values are compatable
Dec 16 13:37:06.837 GMT: FEC: lacp_switch_calculate_oper_key: oper_key for port Gi1/0/5 is 0x6
Dec 16 13:37:07.080 GMT: FEC: lacp_switch_get_first_agg_id_from_admin_oper_keys: found aggregator Po6 for admin_key [0x6] and oper_key [0x6]
Dec 16 13:37:07.080 GMT: FEC: lacp_switch_is_aggregator_valid: aggregator Po6 is still valid
Checked and compared the config from another server, all looks OK.. I tried to search the error message in bold, but can't find any.
Can anyone shed a light?
Many thanks.

we have the same issue with asa5525 and 3750E etherchannel.
The same error
lacp_switch_get_new_agg_id: secondary l3 agg are not supported on the SWITCH side
we are using LACP active from noth sides

Similar Messages

  • DAQmx Error: Non-buffered hardware-timed operations are not supported for this d evice and Channel Type.

    Hello,
    I am new to NI and to data acuasition cards in general. I am trying to put an application togather that would play large audio file using NI9263.
    And i am getting the following error.
    DAQmx Error: Non-buffered hardware-timed operations are not supported for this device and Channel Type.
    Status Code: -201025
    Does my hardware support buffering ?
    can i use the EveryNSamplesCallbackAO function ?
    Any sample code, will be helpful at this time. Thanks.

    Hi yma200,
    Are you using a USB 9263?  If so, this might be of help:
    http://digital.ni.com/public.nsf/allkb/EC1968728E660B288625780700570D06?OpenDocument
    If it doesn't help, can you please post the code that you have that is causing your error?
    Regards,
    Bogdan Buricea
    Applications Engineer
    National Instruments

  • ERROR:MapLib:973 - Tri-state buffers are not supported in this architecture.

    Hi,
    I face a ERROR:MapLib:973 problem with inout port in a pcore component.
    I need ton instantiate an inout port at the top level to communicate wih my peripherical.
    This inout port is driven by an XPS IP core (pcore).
    The .mpd is  :
    PORT fdata = "", DIR = INOUT , VEC = [31:0], ENABLE=SINGLE, THREE_STATE = TRUE,TRI_I = fdata_I, TRI_O = fdata_O, TRI_T = fdata_T
    PORT fdata_I = "", DIR = I , VEC = [31:0]
    PORT fdata_O = "", DIR = O , VEC = [31:0]
    PORT fdata_T = "", DIR = O
    The .vhd is :
    fdata_o : out std_logic_vector(31 downto 0);
    fdata_i : in std_logic_vector(31 downto 0);
    fdata_t : out std_logic ;
    I got ERROR:MapLib:973 - Tri-state buffers are not supported in this architecture messages for each
    signals of my fdata PORT, while mapping !
    Thanks for you help.

    What device are you targeting, and what version of the software are you using?
    I target a xc7k325t-fbg676-2.
    I use ISE 14.3 form platgen to xst and 14.7 from map to bitgen.
    What does your top level HDL (verilog or VHDL) file look like (where the IO must be instantiated)?
    It is a .vhd in whitch i wrapp my top XPS core, described by .mhs
    The problematic IO port is instantiated into the mb_core.vhd (generated by XPS).
    If i open it, i could see that the tool correctly infer the corresponding IOBUF's :
    component mapping :
    fdata_I => FX3_DQ_I,
    fdata_O => FX3_DQ_O,
    fdata_T => FX3_DQ_T,
    One IOBUF infered:
    iobuf_1 : IOBUF
    port map (
    I => FX3_DQ_O(31),
    IO => FX3_DQ(31),
    O => FX3_DQ_I(31),
    T => FX3_DQ_T
    Top level port :
    FX3_DQ : inout std_logic_vector(31 downto 0);
    THEN FX3_DQ  signal is dirrectly branched in my upper level (top level) vhd file, with the same name.
    What do your constraints file look like (where the pin number and names get declared)?
    The port is only constrained in .ucf, like that:
    NET FX3_DQ[0] LOC = "B24"| IOSTANDARD = LVCMOS33 ;
    NET FX3_DQ[31] LOC = "G26"| IOSTANDARD = LVCMOS33 ;#Bank 14
     

  • Maven giving "annotations are not supported in -source 1.3" for  @Entity

    I m using maven for spring, hibernate with jpa . When i m running comman "mvn clean install" ,it is giving error in compilation of a bean class which is using jpa annotations.The error is :
    annotations are not supported in -source 1.3
    (use -source 5 or higher to enable annotations)
    @Entity
    Pom.xml is as below :
    <project xmlns="http://maven.apache.org/POM/4.0.0" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
    xsi:schemaLocation="http://maven.apache.org/POM/4.0.0 http://maven.apache.org/maven-v4_0_0.xsd">
    <modelVersion>4.0.0</modelVersion>
    <groupId>com.niit.core</groupId>
    <artifactId>Spring3Example</artifactId>
    <packaging>jar</packaging>
    <version>1.0-SNAPSHOT</version>
    <name>Spring3Example</name>
    <url>http://maven.apache.org</url>
    <properties>
    <org.springframework-version>3.1.2.RELEASE</org.springframework-version>
    </properties>
    <repositories>
    <repository>
    <id>JBoss Repo</id>
    <url>https://repository.jboss.org/nexus/content/repositories/thirdparty-releases</url>
    </repository>
    </repositories>
    <build>
    <plugins>
    <plugin>
    <artifactId>maven-war-plugin</artifactId>
    <version>2.0</version>
    </plugin>
    </plugins>
    </build>
    <dependencies>
    <dependency>
    <groupId>org.springframework</groupId>
    <artifactId>spring-context</artifactId>
    <version>${org.springframework-version}</version>
    </dependency>
    <!-- <dependency>
    <groupId>hsqldb</groupId>
    <artifactId>hsqldb</artifactId>
    <version>1.8.0.2</version>
    </dependency>
    -->
    <dependency>
    <groupId>org.springframework</groupId>
    <artifactId>spring-core</artifactId>
    <version>${org.springframework-version}</version>
    </dependency>
    <dependency>
    <groupId>junit</groupId>
    <artifactId>junit</artifactId>
    <version>3.8.1</version>
    <scope>test</scope>
    </dependency>
    <dependency>
    <groupId>javax</groupId>
    <artifactId>javaee-api</artifactId>
    <version>6.0</version>
    <scope>provided</scope>
    </dependency>
    <dependency>
    <groupId>org.hibernate</groupId>
    <artifactId>hibernate-core</artifactId>
    <version>3.6.10.Final</version>
    </dependency>
    <dependency>
    <groupId>org.hibernate.java-persistence</groupId>
    <artifactId>jpa-api</artifactId>
    <version>2.0-cr-1</version>
    </dependency>
    <dependency>
    <groupId>org.hibernate</groupId>
    <artifactId>hibernate-entitymanager</artifactId>
    <version>3.5.0-Beta-2</version>
    </dependency>
    <dependency>
    <groupId>javax.servlet</groupId>
    <artifactId>servlet-api</artifactId>
    <version>2.5</version>
    </dependency>
    </dependencies>
    </project>
    And class is as below :
    package com.niit.form;
    import javax.persistence.Column;
    import javax.persistence.Entity;
    import javax.persistence.GeneratedValue;
    import javax.persistence.Id;
    import javax.persistence.Table;
    @Entity
    @Table(name="CONTACTS")
    public class Contact {
    @Id
    @Column(name="ID")
    @GeneratedValue
    private Integer id;
    @Column(name="FIRSTNAME")
    private String firstname;
    public String getFirstname() {
    return firstname;
    public void setFirstname(String firstname) {
    this.firstname = firstname;
    public void setLastname(String lastname) {
    this.lastname = lastname;
    public Integer getId() {
    return id;
    public void setId(Integer id) {
    this.id = id;
    }

    java version is 1.6.0_24
    There is no settings.xml in users/.m2
    I think , maven is using default settings.xml which is in M2_HOME\conf which has everything commented as below:
    <?xml version="1.0" encoding="UTF-8"?>
    <!--
    Licensed to the Apache Software Foundation (ASF) under one
    or more contributor license agreements. See the NOTICE file
    distributed with this work for additional information
    regarding copyright ownership. The ASF licenses this file
    to you under the Apache License, Version 2.0 (the
    "License"); you may not use this file except in compliance
    with the License. You may obtain a copy of the License at
    http://www.apache.org/licenses/LICENSE-2.0
    Unless required by applicable law or agreed to in writing,
    software distributed under the License is distributed on an
    "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
    KIND, either express or implied. See the License for the
    specific language governing permissions and limitations
    under the License.
    -->
    <!--
    | This is the configuration file for Maven. It can be specified at two levels:
    |
    | 1. User Level. This settings.xml file provides configuration for a single user,
    | and is normally provided in $HOME/.m2/settings.xml.
    |
    | NOTE: This location can be overridden with the system property:
    |
    | -Dorg.apache.maven.user-settings=/path/to/user/settings.xml
    |
    | 2. Global Level. This settings.xml file provides configuration for all maven
    | users on a machine (assuming they're all using the same maven
    | installation). It's normally provided in
    | ${maven.home}/conf/settings.xml.
    |
    | NOTE: This location can be overridden with the system property:
    |
    | -Dorg.apache.maven.global-settings=/path/to/global/settings.xml
    |
    | The sections in this sample file are intended to give you a running start at
    | getting the most out of your Maven installation. Where appropriate, the default
    | values (values used when the setting is not specified) are provided.
    |
    |-->
    <settings xmlns="http://maven.apache.org/SETTINGS/1.0.0"
    xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
    xsi:schemaLocation="http://maven.apache.org/SETTINGS/1.0.0 http://maven.apache.org/xsd/settings-1.0.0.xsd">
    <!-- localRepository
    | The path to the local repository maven will use to store artifacts.
    |
    | Default: ~/.m2/repository
    <localRepository>/path/to/local/repo</localRepository>
    -->
    <!-- interactiveMode
    | This will determine whether maven prompts you when it needs input. If set to false,
    | maven will use a sensible default value, perhaps based on some other setting, for
    | the parameter in question.
    |
    | Default: true
    <interactiveMode>true</interactiveMode>
    -->
    <!-- offline
    | Determines whether maven should attempt to connect to the network when executing a build.
    | This will have an effect on artifact downloads, artifact deployment, and others.
    |
    | Default: false
    <offline>false</offline>
    -->
    <!-- pluginGroups
    | This is a list of additional group identifiers that will be searched when resolving plugins by their prefix, i.e.
    | when invoking a command line like "mvn prefix:goal". Maven will automatically add the group identifiers
    | "org.apache.maven.plugins" and "org.codehaus.mojo" if these are not already contained in the list.
    |-->
    <pluginGroups>
    <!-- pluginGroup
    | Specifies a further group identifier to use for plugin lookup.
    <pluginGroup>com.your.plugins</pluginGroup>
    -->
    </pluginGroups>
    <!-- proxies
    | This is a list of proxies which can be used on this machine to connect to the network.
    | Unless otherwise specified (by system property or command-line switch), the first proxy
    | specification in this list marked as active will be used.
    |-->
    <proxies>
    <!-- proxy
    | Specification for one proxy, to be used in connecting to the network.
    |
    <proxy>
    <id>optional</id>
    <active>true</active>
    <protocol>http</protocol>
    <username>proxyuser</username>
    <password>proxypass</password>
    <host>proxy.host.net</host>
    <port>80</port>
    <nonProxyHosts>local.net|some.host.com</nonProxyHosts>
    </proxy>
    -->
    </proxies>
    <!-- servers
    | This is a list of authentication profiles, keyed by the server-id used within the system.
    | Authentication profiles can be used whenever maven must make a connection to a remote server.
    |-->
    <servers>
    <!-- server
    | Specifies the authentication information to use when connecting to a particular server, identified by
    | a unique name within the system (referred to by the 'id' attribute below).
    |
    | NOTE: You should either specify username/password OR privateKey/passphrase, since these pairings are
    | used together.
    |
    <server>
    <id>deploymentRepo</id>
    <username>repouser</username>
    <password>repopwd</password>
    </server>
    -->
    <!-- Another sample, using keys to authenticate.
    <server>
    <id>siteServer</id>
    <privateKey>/path/to/private/key</privateKey>
    <passphrase>optional; leave empty if not used.</passphrase>
    </server>
    -->
    </servers>
    <!-- mirrors
    | This is a list of mirrors to be used in downloading artifacts from remote repositories.
    |
    | It works like this: a POM may declare a repository to use in resolving certain artifacts.
    | However, this repository may have problems with heavy traffic at times, so people have mirrored
    | it to several places.
    |
    | That repository definition will have a unique id, so we can create a mirror reference for that
    | repository, to be used as an alternate download site. The mirror site will be the preferred
    | server for that repository.
    |-->
    <mirrors>
    <!-- mirror
    | Specifies a repository mirror site to use instead of a given repository. The repository that
    | this mirror serves has an ID that matches the mirrorOf element of this mirror. IDs are used
    | for inheritance and direct lookup purposes, and must be unique across the set of mirrors.
    |
    <mirror>
    <id>mirrorId</id>
    <mirrorOf>repositoryId</mirrorOf>
    <name>Human Readable Name for this Mirror.</name>
    <url>http://my.repository.com/repo/path</url>
    </mirror>
    -->
    </mirrors>
    <!-- profiles
    | This is a list of profiles which can be activated in a variety of ways, and which can modify
    | the build process. Profiles provided in the settings.xml are intended to provide local machine-
    | specific paths and repository locations which allow the build to work in the local environment.
    |
    | For example, if you have an integration testing plugin - like cactus - that needs to know where
    | your Tomcat instance is installed, you can provide a variable here such that the variable is
    | dereferenced during the build process to configure the cactus plugin.
    |
    | As noted above, profiles can be activated in a variety of ways. One way - the activeProfiles
    | section of this document (settings.xml) - will be discussed later. Another way essentially
    | relies on the detection of a system property, either matching a particular value for the property,
    | or merely testing its existence. Profiles can also be activated by JDK version prefix, where a
    | value of '1.4' might activate a profile when the build is executed on a JDK version of '1.4.2_07'.
    | Finally, the list of active profiles can be specified directly from the command line.
    |
    | NOTE: For profiles defined in the settings.xml, you are restricted to specifying only artifact
    | repositories, plugin repositories, and free-form properties to be used as configuration
    | variables for plugins in the POM.
    |
    |-->
    <profiles>
    <!-- profile
    | Specifies a set of introductions to the build process, to be activated using one or more of the
    | mechanisms described above. For inheritance purposes, and to activate profiles via <activatedProfiles/>
    | or the command line, profiles have to have an ID that is unique.
    |
    | An encouraged best practice for profile identification is to use a consistent naming convention
    | for profiles, such as 'env-dev', 'env-test', 'env-production', 'user-jdcasey', 'user-brett', etc.
    | This will make it more intuitive to understand what the set of introduced profiles is attempting
    | to accomplish, particularly when you only have a list of profile id's for debug.
    |
    | This profile example uses the JDK version to trigger activation, and provides a JDK-specific repo.
    <profile>
    <id>jdk-1.4</id>
    <activation>
    <jdk>1.4</jdk>
    </activation>
    <repositories>
    <repository>
    <id>jdk14</id>
    <name>Repository for JDK 1.4 builds</name>
    <url>http://www.myhost.com/maven/jdk14</url>
    <layout>default</layout>
    <snapshotPolicy>always</snapshotPolicy>
    </repository>
    </repositories>
    </profile>
    -->
    <!--
    | Here is another profile, activated by the system property 'target-env' with a value of 'dev',
    | which provides a specific path to the Tomcat instance. To use this, your plugin configuration
    | might hypothetically look like:
    |
    | ...
    | <plugin>
    | <groupId>org.myco.myplugins</groupId>
    | <artifactId>myplugin</artifactId>
    |
    | <configuration>
    | <tomcatLocation>${tomcatPath}</tomcatLocation>
    | </configuration>
    | </plugin>
    | ...
    |
    | NOTE: If you just wanted to inject this configuration whenever someone set 'target-env' to
    | anything, you could just leave off the <value/> inside the activation-property.
    |
    <profile>
    <id>env-dev</id>
    <activation>
    <property>
    <name>target-env</name>
    <value>dev</value>
    </property>
    </activation>
    <properties>
    <tomcatPath>/path/to/tomcat/instance</tomcatPath>
    </properties>
    </profile>
    -->
    </profiles>
    <!-- activeProfiles
    | List of profiles that are active for all builds.
    |
    <activeProfiles>
    <activeProfile>alwaysActiveProfile</activeProfile>
    <activeProfile>anotherAlwaysActiveProfile</activeProfile>
    </activeProfiles>
    -->
    </settings>

  • Currently using Flash Pro CS5,  getting error when trying to open CS4 file.  Error is "Slides and Forms documents are not supported in this version of Flash. Please open in previous version.

    Currently using Flash Pro CS5,  getting error when trying to open CS4 file.  Error is "Slides and Forms documents are not supported in this version of Flash. Please open in previous version.  Has there been a fix or patch to this issue or do I have to convert back to CS4 to open the file?

    Having the same problem in CS6.  I can tell you that converting back to CS4 will NOT solve the problem.  It seems when support for backward compatibility is discontinued, there's just no way to get
    any help at all?  Absolute failure to provide any user support so far...

  • Error message: "FireWire connections are not supported.  To transfer songs"

    I recently purchased a Monster iCarPlay to play my ipod in my car. I have had no problems until recently. Upon disconnecting my ipod from the iCarPlay wire, I the following message popped up: "FireWire connections are not supported. To transfer songs, connect the USB cable provided." It also prompts me to click the center button to dismiss the message. However, I'vd followed these instructions, and the message does not go away. Does anyone know what I can do to resolve this problem? Or is it anything to worry about?

    That is the message you see when you attach a 5th gen iPod to a computer using FIREWIRE. so... i suspect that for some reason, the 3rd party iCarPlay device must be confusing the iPod into thinking it is being docked or attached to a data line of some type and not simply charging.
    As for the sudden occurrence of the message, it does seem strange however, keep in mind that you are using a 3rd party device that may not be supported or endorsed by Apple at all.
    Beavis2084

  • "one or more of the items in your selection contains Aperture albums that are not supported in iphoto".

    I have some folders in iPhoto called 'Recovered Folder'. When I try to delete them I get this message: "one or more of the items in your selection contains Aperture albums that are not supported in iphoto".
    I don't use Aperture (did install it to try it out), and have deleted Aperture App from my Mac.
    How can I get rid of these fodlers?

    i finally figured this out:
    fyi, iphoto and aperture can now share (i.e., access) the same library. apple details it here:
    http://support.apple.com/kb/HT5260?viewlocale=en_US&locale=en_US
    i use both iphoto and aperture, and i suspect something went amiss, at some point, while aperture was accessing my iphoto library.
    this is how i fixed the problem:
    i launched aperture, then (per the instructions linked above) switched to (i.e., accessed) my iphoto library. i was then able to delete the "recovered folder" and the album it contained. i then quit aperture and relaunched iphoto.
    NOTE: at that time, although i expected the "recovered folder" to be gone, it was still present. but this time, i was able to delete the folder from within iphoto without the "contains aperture items" error message.
    (Sparky030405, i realize you've since deleted aperture. while i can't say my method is the *only* way to solve this problem, it's the way i was able to solve it. so, you might consider reinstalling aperture in order to delete the folder, then uninstalling aperture, once again.)

  • I have just transfered 2 dvd movies i purchases with digital copies to my itunes account and now i am trying to put them om my ipad it keeps telling me that these movies are not supported on my ipad.  what can i do?

    I have just transfered 2 dvd movies i purchases with digital copies to my itunes account and now i am trying to put them om my ipad it keeps telling me that these movies are not supported on my ipad.  what can i do?

    Highlight the movie, go to iTunes menu ADVANCED and select create iPad and AppleTV version.

  • HT5287 If DVD Movies, Audio CD's and even burning CD and DVD's are not supported, what is the point of DVD & CD Sharing then? Wouldn't it just be better to remote in or use a thumb drive if it's only able to be used for data transfer?

    If DVD Movies, Audio CD's and even burning CD and DVD's are not supported, what is the point of DVD & CD Sharing then? Wouldn't it just be better to remote in or use a thumb drive if it's only able to be used for data transfer?
    Or am I missing the bigger picture?

    As long as you have a Superdrive or an external burner/drive, burning, watching, installing, etc. from CD or DVD will work just fine. And so will sharing.

  • I need to setup 7800 Series IP Phones in the CUCM 8.6.2 which by default are not support but will work after install the software. Anyone have document from Cisco as I remember I seen once before.

    I need to setup 7800 Series IP Phones in the CUCM 8.6.2 which by default are not support but will work after install the software. Anyone have document from Cisco as I remember I seen once before.

    Hi Ali,
    I'll just add this reference to the good tips from my friend Manish (+5)
    Support for the 7800 series in CUCM 8.6.2 was first added with this
    Device Pack;
    Cisco Unified Communications Manager
    Device Package 8.6(2)(24104-1)Release Notes
    Cisco Unified Communications Manager Device Package Release 8.6(2)
    adds support for the Cisco IP Phones
    7821, 7841, and 7861 running SIP firmware release 10.1(1).
    The steps are in this doc
    http://www.cisco.com/web/software/282074299/107528/cmterm-devicepack-8.6.2.24104-1_Readme.pdf
    You might as well install the latest 8.6.2 Device pack
    cmterm-devicepack8.6.2.24112-1.cop.sgn
    Cheers!
    Rob
    "Seek it out and ye shall find  " 
    - OneRepublic

  • Save as PDF and Save PDF as PostScript options in the Printer dialog are not supported.

    I downloaded Indesign CS3 trial and liked everything about it until I attempted to print to postscript and got that message. Nothing I have tried has helped. I have seen in various forums that others are having the same problem, but haven't found any solution offered. I am running Tiger 10.4.10 on a new Intel Imac with 3G ram. This is a procedure I use very often in my workflow, and have never had this problem with CS2 on my PC or other Macs. Is there a solution? I downloaded the .1 update and installed that and it didn't change anything.

    PLEASE SOMEONE HELP ME.
    Its the first time Im using print booklet option to save my file. I have the same problem when trying to save as pdf and get the
    "The Save as PDF and Save PDF as PostScript options in the Printer dialog are not supported."
    I'm trying to save a .pdf of a booklet of a facing pages document of A4 size each facing page for a whole size A3, then hope to let the pages be correctly arranged by inDesing, then print and staple.
    Meaning pages will be like this - Page #60 left side [of the A3] - page #1 right side [of the A3] , page # 2 right side[of the A3] - page #59 left side[of the A3] etc...
    I CANT DO IT. I tried to follow Melvin Thompson , but when I choose save .ps and open it in preview all I see is independent a4 pages and just the left ones , .. How can I save my file as .pdf ready to be printed in a3 ?
    I really appreciate any help.

  • Features that are not supported by Excel in the browser and interactive reports will be removed from the saved copy

    I Created a power view in Excel 2013 and uploaded to my Power BI for o365 site.
    But when i click on my excel file it opens in browser,After that i click on File tab its showing me two option 
    1. Save a Copy
    2.Download a copy
    When i click on save a copy its showing me an warning below
    Features that are not supported by Excel in the browser and interactive reports will be removed from the saved copy.
    Continue with Save?
    If i continue saving it only saves an excel files with data only not the power view which i want to save with applied filters.
    Please help me for this

    Just to clarify, when you hit the option of Save As Copy, the whole experience goes into a "read-write" mode in Excel services, which currently doesn't support authoring, just consumption of PowerView sheets.
    Two mitigations that come to mind:
    1. Download the copy (as Brad suggests), rename the file and upload.
    2. Use the send to option of SharePoint online, give the file the right target document library (can be the same as source) and rename the file:
    GALROY

  • Backend System with Release 701 are not supported

    SRM 5.0
    Extended Classic Scenario
    CCM 2.0
    When updating the vendors in SRM system using TC - BBPUPDVD getting the below error message :-
    Backend System with Release 701 are not supported
    Have checked in table - BBP_BACKEND_DEST, the backend entry is properly maintained.
    Can any one advice.
    Regards,
    Jayoti
    Edited by: SAP jayoti on Dec 7, 2010 1:11 PM

    The problem is resolved for vendor relication after applying the below notes 1313972 and 1372175.
    ECC sandbox seems to be in 701 release. When the backend system ECC is in release 701, vendor replication fails with the error message that 'Backend system release 701 not supported'. We need to apply notes 1313972 and 1372175 to fix this issue. I have applied them in Sandbox and the issue is resolved now.

  • "there was a problem connecting to the server. URLS with the type 'file' are not supported"

    i have a new macbook pro 13" and every 6 minutes or so it pops up a window that says "there was a problem connecting to the server. URLS with the type 'file' are not supported". it never seems to cause any problems but is supremely annoying. how can i make this come to an end?

    I tried someone's solution of taking another external disc and plugging it in, then when it showed up and time machine asked if I wanted to use it or that someone might be trying to trick me, I chose not use it.  Then I  shut down my computer, plugged in the original Lacie, and rebooted the computer and all seems to work fine now-- the Lacie appears on my desktop and all seeems to be in working order. Who knows why or anything else,- as weird as it gets- but for now things seemed fixed--- maybe others can try this too-- it worked for me so far.

  • "There was a problem connecting to the server.   URLs with the type "file:" are not supported.  Why?  What can be done to eliminate it?

    After upgrading to Mountain Lion, I repeatedly get this message:  "There was a problem connecting to the server.   URLs with the type "file:" are not supported. 
    Why? 
    What can be done to eliminate it?

    Open the Time Machine pane in System Preferences. If it shows that Time Machine is ON, click the padlock icon in the lower left corner, if necessary, to unlock it. Scroll to the bottom of the list of backup drives and click Add or Remove Backup Disk. Remove all the disks, then add them back. Quit System Preferences. Test.

Maybe you are looking for