Problem in EP when executing a workbook
Hi all,
in the Enterprise Portal I get this error message:
WSATYPE_NOT_FOUND
The specified class not found
RELEASE 710
COMPONENT NI (network interface)
VERSION 39
RC -1
MODULE ninti.c
LINE 938
DETAIL NiPGetServByName: 'sapmsBAD' not found
SYSTEM CALL getaddrinfo
ERRNO 10109
ERRNO TEXT WSATYPE_NOT_FOUND: The specified class was not found.
COUNTER 3
I like to start a workbook designed in SAP BEx Analyzer from the EP... there is only the problem with workbooks; web templates and queries are working fine.
THX a lot,
Clemens
1. Install SAPGUI
2. saplogon.ini : Give administrative access to User for saplogon.ini
Location C:\WINDOWS
3. Configure the SAP system with ( Application Server , System Id , System Number )
4. Services : Path for services : C:\WINDOWS\system32\drivers\etc
Add following entry at the top in the services
Sapdp<System Number> 3206/tcp
e.g. If System Number = 06
sapdp06 3206/tcp
Similar Messages
-
Error when executing an workbook
Hi all
I have a condition on the base query. The requirement was the user wanted a Selection option range on Key figure, so i had to create a condition with two variable (To and from). Now the problem is when i execute the query with some values in the variables(selection options) workbook work open's up fine but if i leave the condition variables(In selection option) empty and execute i get the below error and disconnects from the BW . Please advice how to overcome this error
<internal Error > Receiving from theBW server failed
BW server raised exception :SYSTEM FAILURE
PS: recently the system is upgraded from 3.5 to BI7.
Thanks in Advance
SheetalHi Sheetal
Try using variable on the required key figure for the selection option. You can select single value, ranges, multiple values with the variable. It should suffice your requirement. -
Problem to spool when Executing reports in background
Hi experts,
I executed reports in backgroud , but when i checked in SM37 the generated spool not given proper layout format.
This problem occurs when report having more columns.
plz help me earliest.
Regards,
jyotsnaHi jyotsna,
this happens with ALV output because the output format is determined at runtime.
You can control the print format used: Just fromyour reports list in online mode, choose PRINT. A Popup should come up letting you specify the printer, number of copies, pages to be printed and so on.
At the bottom of the popup you have the Properties button. This button opens the overview sceen for all the available print parameters. Double-Click the Format section, choose a format you want to use.The the Specifications button takes you to another screen. Here you can choose 'Valid for this report only' and Check the Background checkbox.The push the 'Copy settings' button. Then Enter to close all the popups. This should help. Additionally you can set a default layout variant for your list to be used.
For this, in the ALV list, use Menu Settings-Layout-Layout Management. Here yu can set a default variant.
Regards,
Clemens -
Error when executing the query or refreshing the workbook
Hi All,
Whenever I am trying to execute a query or refresh a workbook a error message is poping up saying that
Error: <internal error> Problem when writing table: E_T_cel.
I face this error in few of the queries and when i refresh workbooks. These queries have lot of calculations and filters and they sum up lot of records.
Any help greatly appreciated.
Thanks
Raj.Hi Maik,
Thanks for reply, I went into tran sm21 but i could not understand the messages there. Below is the list of messages in sm21
System Log: Local Analysis of cdsap9d 1
From date/time............. 04/20/2005 / 10:00:00
To date/time............... 04/21/2005 /
User....................... KADALPR
Transaction code...........
Terminal...................
Task.......................
Problem class..............
Further restrictions.......
Sorted ? ................ SOFI
Pages with single entries 00000100
With statistics............
System Log: Local Analysis of cdsap9d 2
Time Ty. Nr Cl. Tcod MNo Text Date : 20.04.05
12:58:10 DIA 0 100 R49 Communication error, CPIC return code 019, SAP return code 728
12:58:10 DIA 0 100 R5A > Conversation ID: 29858195
12:58:10 DIA 0 100 R64 > CPI-C function: CMSEND(SAP)
12:58:10 DIA 0 100 R68 Perform rollback
12:58:10 DIA 0 100 R47 Delete session 001 after error 003
23:54:49 DIA 1 100 R49 Communication error, CPIC return code 019, SAP return code 728
23:54:49 DIA 1 100 R5A > Conversation ID: 44959947
23:54:49 DIA 1 100 R64 > CPI-C function: CMSEND(SAP)
System Log: Local Analysis of cdsap9d 3
Time Ty. Nr Cl. Tcod MNo Text Date : 21.04.05
09:32:50 DIA 2 100 R49 Communication error, CPIC return code 019, SAP return code 728
09:32:50 DIA 2 100 R5A > Conversation ID: 83536783
09:32:50 DIA 2 100 R64 > CPI-C function: CMSEND(SAP)
Reading:
Number of records read......... 2777
Number of records selected..... 11
Old records skipped............ 2733
Records of invalid users skippe 33
Further selection:
Number of records read......... 11
Number of records selected..... 11
Number of records printed...... 11
End of system log
System Log: Local Analysis of cdsap9d 4
C o n t e n t s
Contents Page Start End
Selection criteria 1
2 20.04.2005 12:58:10 - 23:54:49
3 21.04.2005 09:32:50 - 09:32:50
Contents 4
End of program -
If you can help me out as where to look at these messages then it great.
Thanks,
Raj. -
Warning message in workbook when execute it
Hi Experts,
When I execute a workbook ,I am receiving below warning message,
Warning: There is a condition on Customer Store ,results row suppress ,active on Customer
Warning: There is a condition on Customer PO Number ,results row suppress ,active on Custom
Warning: There is a condition on Material,results row suppress ,active on DIM1[ZDIM
After I select close warning message,it is excuting and results are shown.Today i automate the report execution.But its ended with ABAP\4 raise exception short dump and job got failed.Pls advice me how to avoid it.HI Malini,
Run the Queries induvidually in rsrt and suppress the messages in it.
Thne try to run the work Book.
Hope this solves the issue.
Regards.
Shafi. -
Expdp problem when executing from pl/sql transportable tablespaces
Hello
i have a very strange problem for which your assistance is really appreciated. i am applying the transportable tablespaces approach and i have a problem when executing expdp from commandline in comparison to the procedure generated to make the exact same thing.
more precisely when running:
expdp etl/etl dumpfile=TBSP090609_DMP.dmp logfile=TBSP090609_DMP.log directory=EXPDP transport_tablespaces=TBSP090609 transport_full_check=y
the dmp file produced is over 200MB.
when runng the below pl/sql code the volume produced is around 50MB. any idea what i am missing?
job_handle :=
dbms_datapump.OPEN (operation => 'EXPORT',
job_mode => 'TRANSPORTABLE',
job_name => 'export_tablespace',
VERSION => 'COMPATIBLE'
dbms_datapump.add_file (handle => job_handle,
filename => dump_file_name,
DIRECTORY => export_dir_name
dbms_datapump.set_parameter (handle => job_handle,
NAME => 'TTS_FULL_CHECK',
VALUE => 1
dbms_datapump.metadata_filter (handle => job_handle,
NAME => 'TABLESPACE_LIST',
VALUE => '('''
|| tablespace_name
|| ''')'
dbms_datapump.start_job (job_handle);thanx you for your response. the problem was eventually managed to be resolved as follows:
job_handle :=
dbms_datapump.OPEN (operation => 'EXPORT',
job_mode => 'TRANSPORTABLE',
job_name => 'export_tablespace',
VERSION => 'COMPATIBLE'
dbms_datapump.add_file (handle => job_handle,
filename => dump_file_name,
DIRECTORY => export_dir_name
dbms_datapump.set_parameter (handle => job_handle,
NAME => 'TTS_FULL_CHECK',
VALUE => 1
dbms_datapump.metadata_filter (handle => job_handle,
NAME => 'TABLESPACE_EXPR',
VALUE => 'IN('''
|| tablespace_name
|| ''')');
dbms_datapump.start_job (job_handle); -
Menu bar problem when executing reports
We have a problem when executing the reports either from se38 or through transaction.
The standard menu bar is not appearing and in its place we are getting ????????????? ?????????????????
also the icons that are appearing in app tool bar are not showing anything.
Whats the reason for this?hi,
It is not for one single report iam talking about,any report that is executed from se38 or transaction .
In selection screen of report we are getting ???????????????
?????????????? in menu bar instead of normal options like program edit goto utilities.................
does any one know the reason for this?
This issue we are facing today only.
Edited by: Gautham chakraverthi on Oct 31, 2008 3:06 PM -
Excel 2011 problem: windows resize automatically when switching between workbooks
I am facing a very annoying problem when opening several workbooks in Excel. When shifting from one workbook to the other (either by selecting the workbook from the menu list, or by cycling through using 'cmd + ~'), the workbook jumps to a smaller size automatically. I have to click the green + button twice before it stays on the maximum window size again. Very frustrating experience when you have to switch between workbooks regularly.
Anyone experiencing the same problem? Is there a solution to this?
I am using Excel for Mac 2011. Just upgraded my MacBook Pro to Yosemite 10.10.1, but was facing the same problem using Mountain Lion.
Hope someone can help me out!3/1//2015
Hello. Thank you for posting your questions. I followed the suggestions and found that nothing worked on my computer. So I tried clicking around and found 2 solutions.
1. On the top tool bar, Click on "View" and scroll down to " Enter Full Screen". The tabs were easily accessible.
My Favorite now:
2. On the top tool bar, Clck on "Window" and scroll down to "New Window". This will duplicate your desired window in a "complete with tabs- window". I then Exited/Clicked out of the "offending" window.
I think clicked back in the "good" window and clicked "Save".
I was able to close out the document and re-enter it from my Finder Window.
Problem Fixed.
I hope those of you out there can have this work on your machines.
I am running OS X Yosemite 10.10.2 on a Mid 2014. -
Performance Problem when executing the report for the first time.
Hi,
We have a Zreport...to improve the performance i created Index on few Data Base table..before my changes it used to take more than 15 minutes after the changes it taking less than 1 min for the same variant and for other variants also.
But when executing the first in morning its taking the same time more than 15 min.Please let me know how to increase the performance when executing first time also,
Thanks,
Kiran.Hi all,
Appreciate your valuable replies...
@ Thomas: i do accept with your solution running a background job..but user is not accepting for it..thanks for your reply.
@Siegfried Boes : for testing purpose Im running this manytimes..but for user they may
require when ever they need to know open oders.the volume of the data is barongs 300-350 at
max.
@Brad Bohn : After creating the index the repose time reduced to half ...i hope i have
created a right index.
Observation here...I executed the report in production system more than 5 times it took the
same time, my changes are still in quality..so i think may be for selecting the right index
its taking this much time.and for the next time is taking right index n doing it so it taking
less.
Do you accept it?.if so Please let me know how to explicitly say the select statement to
use my index.
Thanks,
kiran. -
Problem When executing chart in the Web
Hi all,
I am getting the following error when executing a chart in the Web.
Diagnosis
Internal error when communictaing with the IGS (charts).
System response Internal error text: "Error opening an RFC connection."
Procedure
Procedure for System Administration
Notification Number RSWWW 005
Thanks.Hi,
this looks like your IGS has crashed and somehow needs to be restarted. I also assume that the IGS patchlevel is old in comparison to the newest version in the Service Marketplace.
Please update the IGS (which includes a restart) or ask your basis team to upgrade the IGS.
FYI: Note <a href="http://service.sap.com/sap/support/notes/931900">931900</a> describes how to discover the IGS patchlevel even when it is not running.
Regards
Matthias -
Error while executing the workbook query.
Hi guyz
i'm getting an error while executing the workbook Query. The actual problem is there is a filter for REQUID in the query definition for removing the doble count. there is customer exit written. the report works fine in DEVELOPMENT but it is not working in quality.
The query on which this workbook is created is working fine, but the problem is when we execute the workbook i'm facing this issue.
we re-transported the queries but still we are facing the same problem.
while we execute the query we are prompted for variable entry(Optional) for date. when we press OK we get the below error
" NO SID value found for the value REQU_4DQT75Y2RJPVT4PXZ4LHC70V3 of characteristic"
the request is not available in the BW system. the request was deleted long back, but it is still referring to the same the request id
could someone please tell me where we went wrong and why we are getting this error.
Regards,
Anil VaddeHey ,I think data load to your target on which the query was based had some issue.
Can you check the data load to the data target.change the status of request concerned to red and delete.do reconstruct if neeed..I think the request had some issue.
Even you can go to RSRQ or RSMO and filter on the basis of this request and see its status.
Regards,
RK -
Query not refreshing all data when run in workbook with other queries
All,
I have the following problem. I have a workbook that has two queries, one on each tab.
The specific thing I notice that the company code is not showing up in the query at first until I hit refresh. Both queries use the same company code and user variables. When running the workbook I have each query set to "refresh query when running workbook". I have been able to duplicate this problem in either of the two queries, depending upon which company code variables I use. When I run the workbook, one of the two queries never updates company code variable unless I "refresh" the query directly after pulling up the workbook.
I have changed the company code variable and used other company codes in each query, some required, some not, but ultimately a few of the key figures are not populating with current data and the company code is missing...unless I hit refresh on that query. I have tried creating new workbooks and removing and reinserting the queries, but this doesn't work either.
And both queries run fine when executed alone.
Again, Both queries use the same company code variable.
Any help will be rewarded with points and is appreciated.Tasha,
Remove the queries from the workbook and reinsert them. This should show the desired result. -
SQL error 3113 occurred when executing EXEC SQL.
Hi,
We are facing one typical problem, One background is failing regularly with
below dump. as we now got all notes giving information, if database restarted
taking backup, these type of failures occur, but our database is only down for backup once in a week, but it is failing with frequenly.
in this two servers are located in different place, in this job tries to connect
another server to get material statistics.
It is giving some error message in sm21 with
SQL error 3113 occurred when executing EXEC SQL.
work procees in reconnect mode.
all notes saying these types of dump occur when database restared, but this dump
even though database is up.
below is short dump, please can anyone help me from this problem.
ABAP runtime errors DBIF_DSQL2_SQL_ERROR
Occurred on 08.01.2007 at 00:30:28
>> Short dump has not been completely stored. It is too big.
SQL error 3113 occurred when executing EXEC SQL.
What happened?
The error occurred in the current database connection "AZ1".
What can you do?
Note the actions and input that caused the error.
Inform your SAP system administrator.
You can print out this message by choosing "Print". Transaction ST22
allows you to display and manage termination messages, including keeping
them beyond their normal deletion date.
Error analysis
How to correct the error
Database error text........: "ORA-03113: end-of-file on communication channel#"
Triggering SQL statement...: "select mara.groes, mara.brgew, mara.ntgew,
mara.gewei, mara.volum, mara.voleh, mara.mstae, mara.mstde, mara.prdha,
marc.matnr, marc.werks, marc.mmsta, marc.mmstd from sapr3.mara, sapr3.m
where sapr3.mara.mandt = sapr3.marc.mandt and sapr3.mara.matnr =
Internal call code.........: "[DBDS/NEW DSQL]"
Please check the entries in the system log (Transaction SM21).
If the error occurred in a non-modified SAP program, you may be
able to find a solution in the SAP note system.
If you have access to the note system yourself, use the following
search criteria:
"DBIF_DSQL2_SQL_ERROR"
"ZM2431216 " or "ZM2431216 "
"EXTRACT_GENERAL_DATA"
If you cannot solve the problem yourself, please send the
following documents to SAP:
1. A hard copy print describing the problem.
To obtain this, select the "Print" function on the current screen.
2. A suitable hardcopy prinout of the system log.
To obtain this, call the system log with Transaction SM21
and select the "Print" function to print out the relevant
part.
3. If the programs are your own programs or modified SAP programs,
supply the source code.
To do this, you can either use the "PRINT" command in th
print the programs using the report RSINCL00.
4. Details regarding the conditions under which the error o
or which actions and input led to the error.
System environment
SAP Release.............. "46C"
Application server....... "essceu3"
Network address.......... "172.19.119.198"
Operating system......... "AIX"
Release.................. "5.3"
Hardware type............ "00C7ADBD4C00"
Database server.......... "ukblx176"
Database type............ "ORACLE"
Database name............ "EU3"
Database owner........... "SAPR3"
Character set............ "es_ES.ISO8859-1"
SAP kernel............... "46D"
Created on............... "Jul 9 2006 20:26:33"
Created in............... "AIX 1 5 00447C4A4C00"
Database version......... "OCI_920__OCI_7_API "
Patch level.............. "2257"
Patch text............... " "
Supported environment....
Database................. "ORACLE 8.0.5.., ORACLE 8.0.6.., ORACLE
8.1.6.., ORACLE 8.1.7.., ORACLE 9.2.0.., ORACLE 10.2.0.."
SAP database version..... "46D"
Operating system......... "AIX 1 4, AIX 2 4, AIX 3 4, AIX 1 5, AIX 2 5, AIX 3
5, , System build information:, , LCHN :
841480"
User, transaction...
Client.............. 600
User................ "MPZMMES"
Language key........ "S"
Transaction......... " "
Program............. "ZM2431216 "
Screen.............. "SAPMSSY0 1000"
Screen line......... 6
Information on where termination occurred
The termination occurred in the ABAP/4 program "ZM2431216 " in
"EXTRACT_GENERAL_DATA".
The main program was "ZM2431216 ".
The termination occurred in line 980
of the source code of program "ZM2431216 " (when callin
The program "ZM2431216 " was started as a background jo
Source code extract
009500 mara.ntgew,
009510 mara.gewei,
009520 mara.volum,
009530 mara.voleh,
009540 mara.mstae,
009550 mara.mstde,
009560 mara.prdha,
009570 marc.matnr,
009580 marc.werks,
009590 marc.mmsta,
009600 marc.mmstd
009610 into :w_ops-groes,
009620 :w_ops-brgew,
009630 :w_ops-ntgew,
009640 :w_ops-gewei,
009650 :w_ops-volum,
009660 :w_ops-voleh,
009670 :w_ops-mstae,
009680 :w_ops-mstde,
009690 :w_ops-prdha,
009700 :w_ops-matnr,
009710 :w_ops-werks,
009720 :w_ops-mmsta,
009730 :w_ops-mmstd
009740 from sapr3.mara, sapr3.marc
009750 where sapr3.mara.mandt = sapr3.marc.mandt
009760 and sapr3.mara.matnr = sapr3.marc.matnr
009770 and sapr3.mara.mandt = :p_mandt
009780 and sapr3.mara.matnr = :w_ebs-matnr
009790 and sapr3.marc.werks = :p_owerks
> ENDEXEC.
009810 endform. " extract_general_data
009820 *&
009830 *& Form append_i_ops
009840 *&
009850 * Appends W_OPS to I_OPS
009860 *
009870 form append_i_ops.
009880 append w_ops to i_ops.
009890 endform. " append_i_ops
009900 *&
009910 *& Form extract_material_description
009920 *&
009930 * Extracts a Material Description from the remote database an
009940 * modifies the current record in I_OPS.
009950 *
009960 * >P_SPRAS Language Key
009970 *
009980 form extract_material_description using p_spras.
009990 EXEC sql performing set_langauge.
Contents of system fields
SY field contents..................... SY field contents............
SY-SUBRC 0 SY-INDEX 0
SY-TABIX 1 SY-DBCNT 1
SY-FDPOS 18 SY-LSIND 0
SY-PAGNO 0 SY-LINNO 1
SY-COLNO 1
Chosen variables
Name.......................... Contents.1........2........3....+..
W_EBS-PRAT4
2
0
W_OPS-GROES
22222222222222222222222222222222
00000000000000000000000000000000
W_OPS-BRGEW #######
0000000
000000C
W_OPS-NTGEW #######
0000000
000000C
regards,
krishnaiah.Hi,
This is usually a SERVER SIDE DATABASE PROBLEM or SQLNET LISTENER (server side) PROBLEM. The client side should initially be ignored and instead the server should be investigated. In rare cases, this can be caused by client
side memory or other resource problem, or a DLL version mismatch, but this is
unlikely.
Enlist the assistance of your DBA. Then reproduce the ORA-3113 error on your
client application. Ask your DBA to look at the database side Alert.log and
trace files and look for ANY activity. Any activity that coincides with your
ORA-3113 will be a clue.
REgards
Vinod -
Vi works in LabVIEW, but not when executed by TestStand.
Hi everybody. I'm using LabVIEW 8 with the Sound and Vibration
Toolkit, and TestStand2. I am planning on using TestStand to
execute a series of performance tests on an audio processing
board. When run independently, the vi (which I have attached
here) runs correctly, and returns a value for the parameter being
tested. In this case it is SNR.
However, when executed by TestStand, the vi seems to run correctly, but
returns a value of "NaN". This causes TestStand to fail the test.
Does anybody know what is going on here? I've checked FAQs and
help files, etc... Why would the vi work on its own but not in
TestStand?
Thanks.
Brett Gildersleeve
Attachments:
SingleChannelSNR.vi 173 KB
Test Sequence.seq 15 KBHi Ray, Thanks for the reply.
Basically, when I run the VI on its own, I see the SNR value appearing
both in the SNR indicator and in the Test Data Out cluster under
Numeric Measurement. The rest of the indicators are empty
(string, report text, status, code, source). My waveform graph
shows an FFT of the signal.
However, when running the exact same VI through TestStand, I get NaN as
the output. The FFT of the signal is NOT displayed in the
waveform graph... strange. No errors are received.
In order to make it easier to debug, I replaced all of the analysis functions
with functions included in LabVIEW 8. Now everybody should be
able to run it. I do a simple THD test this time around. With the VI running
on its own, I get a value of 1.8 as the THD and the Numeric Measurement of Test Data
Out. However, whenever running the test with TestStand, I get a
value of NaN.
Same problem.
Any suggestions?
By the way, what exactly do you mean by "wiring
up the Error cluster and feed in to the Error Out."? I'd
like to try it out, but I'm not sure exactly what you mean. I
already have the Error out cluster wired up, I think.
Message Edited by TheSleeve on 05-22-2006 12:12 PM
Attachments:
SingleChannelTHD.vi 159 KB
Test Sequence2.seq 15 KB -
Error when executing query without passing variable selection
Hi Gurus
I am getting an error while executing a query with out passing values for variables
When executing the query by passing the filter values report returns the data
When executing the query with out passing variable selections the error message is
Unknown error in SQL interface
Error reading the data of Info Provider ZCRM_O08
Error while reading data; navigation possible
System error in program SSAPLRS_EXCEPTION and form
RS_EXCEPTION_TO_MESSAGE
No Data Available
can any one please help me in resolving this
Thank youHi Srini
Thanks for your quick response
When i am executing the query with selection it is returning the data
giving error when executing with out passing the selection
is there any other cause for this problem
like any particular info object causes this sort of problem
Thank you
Maybe you are looking for
-
Vendor Master Replication Error from ECC to SUS : Error in ALE Service
Dear Experts, We are implementing MM SUS (SRM 5.0). As a part of this we need to replicate vendors from ECC to SUS system via XI. We have created a Reduced Message Type Z_CREMAS_SUSMM and had set up the partner profile in WE20 with SUS logical system
-
Question about "Get Web Drawing URL and Page Name From" for Visio Web Access
I am trying to get both the web drawing URL and the page name from a list through Share Point Designer 2013, but it doesn´t work. It looks fine when a do the web part connection wizard. I select from which columns to get the URL and the page name. Bu
-
Major query performance differnce between oracle 8 and 9
Hello, I have the following query select distinct UPPER(rf.module), ruf.rpt_seq from role_func rf, rd_url_func ruf where role_name = 'ADMIN' and UPPER(rf.module) not in (select UPPER(ruf.module)
-
Can't copy and paste address in Mail
Copy and paste works everywhere else but in the address field in Mail. I've got ver. 5.3. When I Control-Click on the curser in the address field, I don't get the drop down menu with Paste on it. Any one else seen this? Thanks.
-
Hi All, I am using standard pricing condition FRB1 for standard PO . Busienss requirement is to define FRB1 in document header condition and the same should be distributed to all the line items in PO document on prorata basis of each line item value.