Problem setting vty password in packet tracer

I'm trying to configure a vty password in packet tracer and I think I'm doing something wrong. These are the commands I'm using:
line vty 0
password test
end
When I do showrun I can see the command, but when I try to get access to the vty line, it never ask's me for the password. What am I doing wrong.
Screen shot included. Thanks.

As far as I know, you can't assign an IP address to an individual interface, but you can assign an administrative IP address to the switch itself. This screen shot is the commands that I used to assign an ip address, subnet mask & gateway. And I have done this on real 2960g.

Similar Messages

EtherChannel with Packet Tracer

I tried in Packet Tracer to bundle 4 links between 2 switches, each switch is connected to a host.
when I try to ping from host to other, it pings and successful, but when I try to disconnect a cable, which the selected link by the PAgP, it says Request timed out.
and it can't ping till I return that cable back again, what is the problem?

Hello, i have packet tracer 6.2, and i use Switches 3560(L3), my portchannel have two ports, when i reload de Switch1, after to startup the Switch appear this message
%EC-5-CANNOT_BUNDLE2: Fa0/1 is not compatible with Po1 and will be suspended (trunk encap of Fa0/1 is auto Po1 is dot1q)
%EC-5-CANNOT_BUNDLE2: Fa0/2 is not compatible with Po1 and will be suspended (trunk encap of Fa0/2 is auto Po1 is dot1q)
Do you Know what is the problem
CONFIG S1
interface Port-channel 1
switchport trunk allowed vlan 10,20
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/1
channel-protocol pagp
channel-group 1 mode auto
switchport trunk allowed vlan 10,20
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/2
channel-protocol pagp
channel-group 1 mode auto
switchport trunk allowed vlan 10,20
switchport trunk encapsulation dot1q
switchport mode trunk
CONFIG S2
interface Port-channel 1
switchport trunk allowed vlan 10,20
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/1
channel-protocol pagp
channel-group 1 mode desirable
switchport trunk allowed vlan 10,20
switchport mode trunk
interface FastEthernet0/2
channel-protocol pagp
channel-group 1 mode desirable
switchport trunk allowed vlan 10,20
switchport mode trunk
Thanks

Problems setting up username & password for SQL

Due to the outstanding advice I recieved from this excellent forum, I have managed to overcome my first problem with declaring a new Class.
This leads me to request help with my next biggest problem:
Setting up a user GUI that takes a "username" & "password" that will be used to access a password protected database.
I am a simple bloke, with simple thought processes, so please, go easy on me...
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.sql.*;
public class DBQuery1 {
     String username = "" , password = "";
     public static void main(String[] arguments) {
          PassDB UPass = new PassDB();
          String data = "jdbc:odbc:JavaTestDataBase";
          try {
               Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
               Connection conn = DriverManager.getConnection(data, "" + username, "" + password);
               Statement st = conn.createStatement();
               ResultSet rec = st.executeQuery(
                    "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
                    + "WHERE (Title='Mr') ORDER BY ContactID");
          /*     ResultSet rec2 = st.executeQuery(
                    "SELECT Subject, ContactID FROM Calls "
                    + "WHERE (Subject Is Not Null) ORDER BY ContactID");
          System.out.println("\nFirst Name\tSurname\t\tNick Name\t\tSubject\n");
          while(rec.next()) {
               System.out.println(rec.getString(3) + "\t\t" + rec.getString(4) + "\t\t" + rec.getString(5) /* + rec2.getString(1) */ );
          st.close();
          catch (SQLException s) {
               System.out.println("SQL Error: " + s.toString() + " " + s.getErrorCode() + " " + s.getSQLState());
          catch (Exception e) {
               System.out.println("Error: " + e.toString() + e.getMessage());
class PassDB extends javax.swing.JFrame implements ActionListener {
     String username = "", password = "";
     JTextField uname = new JTextField(10);
     JTextField pword = new JTextField(10);
     // JPasswordField pword = new JTextField(10);
     PassDB() {
          super("duBe's database logon");
          setSize(220, 160);
          setDefaultCloseOperation(EXIT_ON_CLOSE);
          JPanel pane = new JPanel();
          JLabel unameLabel = new JLabel ("Username: ");
          JLabel pwordLabel = new JLabel ("Password: ");
          JButton submit = new JButton("OK");
          submit.addActionListener(this);
          pane.add(unameLabel);
          pane.add(uname);
          pane.add(pwordLabel);
          pane.add(pword);
          pane.add(submit);
          setContentPane(pane);
          setVisible(true);
     public void actionPerformed(ActionEvent evt) {
          PassDB clicked = (PassDB)evt.getSource();
          username = uname.getText();
          password = pword.getText();
This code generates two errors, stating:
C:\Java_progs>javac DBQuery1.java
DBQuery1.java:14: non-static variable username cannot be referenced from a static context
Connection conn = DriverManager.getConnection(data, "" +
username, "" + password);
^
DBQuery1.java:14: non-static variable password cannot be referenced from a static context
Connection conn = DriverManager.getConnection(data, "" +
username, "" + password);
                ^
2 errors*****************************
The code works when I remove the reference to the variables "username" & "password" in Connection "conn" call & replace them with the actual username & password, but this is not exactly what I was after. I was hoping to make the program responsive to each individual user, not set in code.
I also would like to make the program pause after the call in "main" to "PassDB" to wait for "PassDB" to exit before continuing.
I would also like to make "PassDB" destroy itself after the "OK" button is pressed & the "username" & "password" set.
If that isn't enough for you, I would really like the program to search 2 different database tables, return their values & compare them to be sure that they are the same.
When I try & search 2 different tables, as in:
ResultSet rec = st.executeQuery(
                    "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
                    + "WHERE (Title='Mr') ORDER BY ContactID");
               ResultSet rec2 = st.executeQuery(
                    "SELECT Subject, ContactID FROM Calls "
                    + "WHERE (Subject Is Not Null) ORDER BY ContactID")javac tells me that "ResultSet" is set to null 0
As always, I am extremely appreciative of any assistance you are able to offer.
Kind regards
duBedat
[email protected]

This is where I'm at now:
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.sql.*;
public class DBQuery {
     static String username = "" ;
     static String password = "" ;
     public static void main(String[] arguments) {
     PassDB UPass = new PassDB();
     String data = "jdbc:odbc:JavaTestDataBase";
     try {
          Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
          Connection conn = DriverManager.getConnection(data, "" + DBQuery.username, "" + DBQuery.password);
          Statement st = conn.createStatement();
          ResultSet rec = st.executeQuery(
          "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
          + "WHERE (Title='Mr') ORDER BY ContactID");
          /*     ResultSet rec2 = st.executeQuery(
               "SELECT Subject, ContactID FROM Calls "
               + "WHERE (Subject Is Not Null) ORDER BY ContactID");
          System.out.println("\nFirst Name\tSurname\t\tNick Name\t\tSubject\n");
          while(rec.next()) {
               System.out.println(rec.getString(3) + "\t\t" + rec.getString(4) + "\t\t" + rec.getString(5) /* + rec2.getString(1) */ );
          st.close();
     catch (SQLException s) {
          System.out.println("SQL Error: " + s.toString() + " " + s.getErrorCode() + " " + s.getSQLState());
     catch (Exception e) {
          System.out.println("Error: " + e.toString() + e.getMessage());
class PassDB extends javax.swing.JFrame implements ActionListener {
     static boolean getOut = false;
     JTextField uname = new JTextField(10);
     JTextField pword = new JTextField(10);
     // JPasswordField pword = new JTextField(10);
     public PassDB() {
          super("duBe's database logon");
          setSize(220, 160);
          setDefaultCloseOperation(EXIT_ON_CLOSE);
          JPanel pane = new JPanel();
          JLabel unameLabel = new JLabel ("Username: ");
          JLabel pwordLabel = new JLabel ("Password: ");
          JButton submit = new JButton("OK");
          submit.addActionListener(this);
          pane.add(unameLabel);
          pane.add(uname);
          pane.add(pwordLabel);
          pane.add(pword);
          pane.add(submit);
          setContentPane(pane);
          while(getOut == false)
               setVisible(true);
     public void actionPerformed(ActionEvent evt) {
          PassDB clicked = (PassDB)evt.getSource();
          DBQuery.username = uname.getText();
          DBQuery.password = pword.getText();
          getOut = true;
}          Any advice is greatly appreciated
duBe

PROBLEMS SETTING UP EMAILS AS DEVICE REFUSES TO RECOGNISE PASSWORD AND/OR USER NAME

PROBLEMS SETTING UP EMAILS AS DEVICE REFUSES TO RECOGNISE PASSWORD AND/OR USER NAME
My 9800 ( I have 2 - one spare ) is driving me nuts- will not let me set up email accounts from my other Curve model.
Repeatedly told that either user name or details are wrong, yet they are RIGHT on website.
Exasperated
Help please??
Fair winds and kind landfalls

Thank you- I have read through that thread and can see some resonance with my issue.
My AOL emails work VERY fast with BB, in fact almost simultaneously received on PC & Torch " ping ping!"
This issue only raised its ugly head when I had 2 Torches replaced by my insurers.
Whilst the claim was in process I used a new Curve, loaded from backup on PC to keep emails going and of course phone & web facilities. ( I use the BB to power internet via bluetooth to my PC / laptop when living on a remote island with no phone lines or power supplies) All was fine. Swapping email accounts took a few minutes with the usual password confirmations for each AOL screenname etc.
Then the new Torches came back from insurers, and I tried to swap devices. Phoning & texting is fine. Al data and contacts swap over fine.
SETUP email accounts.............stymied every time. It says repeatedly that my user name/password is invalid etc etc etc
Have tried security wipes. Have tried setting up new BB ID & passwords on PC website. All is OK until I try to setup emails on the Torches. This has used up ridiculous amounts of time- all wasted.
I love the BB phones and the fast email push......in fact I recently bought a new Sony Xperia Z1 but sent it back because of wifi coverage meant no emails on that superb phone for lots of the time.
Good old BB I said..........I always get emails wherever I am. ( Rural Scotland has very patchy radio & wifi coverage)
Was about to purchase new Z10s just to get a bigger screen, but now I am averse to buying ANY BB phone again because this present mess means I may never get emails set up again. How nuts is that?
Many thanks for all help & suggestions..........boy do I need them!!
Kind wishes from West of Scotland
Fair winds and kind landfalls

Im having problem setting up my Hotmail account, it used to work fine until few days ago. It says ive entered an incorrect username or password which i can sign in fine with them details if i use laptop or safari through the phone, Please help..

Im having problem setting up my Hotmail account, it used to work fine until few days ago. It says ive entered an incorrect username or password which i can sign in fine with them details if i use laptop or safari through the phone, Please help..

I Sugges you to log into your hotmail acc and go to security and password change bit, then you will see two-step verification.. turn that off and you will be able to set it up on your iPhone/iPad or even Mac.
Give your phone a restart before trying to set it up. Thanks

New problem while setting ADS password

Hi,
Im trying to change password in ADS. Ultimately it has to be done via web interface but i was trying it out on my local machine, which has windows 2000. I got the following exception as a result. Any ideas?
This is my code section ...
Hashtable env = new Hashtable();
env.put( Context.INITIAL_CONTEXT_FACTORY, "com.sun.jndi.ldap.LdapCtxFactory" );
env.put(Context.PROVIDER_URL, "ldap://10.2.0.22:636/");
env.put(Context.SECURITY_AUTHENTICATION,"simple");
env.put(Context.SECURITY_PROTOCOL, "ssl");
env.put(Context.REFERRAL,"ignore");
env.put(Context.SECURITY_PRINCIPAL,"[email protected]");
env.put(Context.SECURITY_CREDENTIALS,"Password1");
DirContext dctx = null;
try
dctx = new InitialDirContext( env );
The following is the exception i got ...
javax.naming.CommunicationException: simple bind failed: 10.2.0.22:636 [Root exception is javax.net.ssl.SSLProtocolExcep
tion: java.io.IOException: subject key, Unknown key spec: Invalid RSA modulus size.]
at com.sun.jndi.ldap.LdapClient.authenticate(LdapClient.java:198)
at com.sun.jndi.ldap.LdapCtx.connect(LdapCtx.java:2640)
at com.sun.jndi.ldap.LdapCtx.<init>(LdapCtx.java:290)
at com.sun.jndi.ldap.LdapCtxFactory.getUsingURL(LdapCtxFactory.java:175)
at com.sun.jndi.ldap.LdapCtxFactory.getUsingURLs(LdapCtxFactory.java:193)
at com.sun.jndi.ldap.LdapCtxFactory.getLdapCtxInstance(LdapCtxFactory.java:136)
at com.sun.jndi.ldap.LdapCtxFactory.getInitialContext(LdapCtxFactory.java:66)
at javax.naming.spi.NamingManager.getInitialContext(NamingManager.java:662)
at javax.naming.InitialContext.getDefaultInitCtx(InitialContext.java:243)
at javax.naming.InitialContext.init(InitialContext.java:219)
at javax.naming.InitialContext.<init>(InitialContext.java:195)
at javax.naming.directory.InitialDirContext.<init>(InitialDirContext.java:80 )
at updtpass.main(updtpass.java:34)
Caused by: javax.net.ssl.SSLProtocolException: java.io.IOException: subject key, Unknown key spec: Invalid RSA modulus s
ize.
at com.sun.net.ssl.internal.ssl.HandshakeMessage$CertificateMsg.<init>(Dasho A12275)
at com.sun.net.ssl.internal.ssl.SunJSSE_az.a(DashoA12275)
at com.sun.net.ssl.internal.ssl.SunJSSE_ax.a(DashoA12275)
at com.sun.net.ssl.internal.ssl.SSLSocketImpl.a(DashoA12275)
at com.sun.net.ssl.internal.ssl.SSLSocketImpl.j(DashoA12275)
at com.sun.net.ssl.internal.ssl.SSLSocketImpl.a(DashoA12275)
at com.sun.net.ssl.internal.ssl.AppOutputStream.write(DashoA12275)
at java.io.BufferedOutputStream.flushBuffer(BufferedOutputStream.java:66)
at java.io.BufferedOutputStream.flush(BufferedOutputStream.java:124)
at com.sun.jndi.ldap.Connection.writeRequest(Connection.java:390)
at com.sun.jndi.ldap.LdapClient.ldapBind(LdapClient.java:334)
at com.sun.jndi.ldap.LdapClient.authenticate(LdapClient.java:193)
... 12 more
Caused by: java.security.cert.CertificateParsingException: java.io.IOException: subject key, Unknown key spec: Invalid R
SA modulus size.
at sun.security.x509.X509CertInfo.<init>(X509CertInfo.java:155)
at sun.security.x509.X509CertImpl.parse(X509CertImpl.java:1679)
at sun.security.x509.X509CertImpl.<init>(X509CertImpl.java:173)
at sun.security.provider.X509Factory.engineGenerateCertificate(X509Factory.java:90 )
at java.security.cert.CertificateFactory.generateCertificate(CertificateFactory.ja va:389)
... 24 more
Caused by: java.io.IOException: subject key, Unknown key spec: Invalid RSA modulus size.
at sun.security.x509.X509Key.parse(X509Key.java:155)
at sun.security.x509.CertificateX509Key.<init>(CertificateX509Key.java:58)
at sun.security.x509.X509CertInfo.parse(X509CertInfo.java:706)
at sun.security.x509.X509CertInfo.<init>(X509CertInfo.java:153)
... 28 more
Exception in thread "main" java.lang.NullPointerException
at updtpass.main(updtpass.java:61)

I am also facing a peculiar type of problem while setting the password
the type of error I am while running the code below
String adminName = "CN=xyz,CN=Users,DC=TESTING, DC=AMG, DC=COM";
String adminPassword = "xxxxxxx";
String ldapURL = "ldap://testing.amg.com:636";
String keystore = "/Program Files/Java/jre1.5.0_03/lib/security/cacerts";
System.setProperty("javax.net.ssl.trustStore",keystore);
env.put(Context.INITIAL_CONTEXT_FACTORY,"com.sun.jndi.ldap.LdapCtxFactory");
env.put(Context.SECURITY_AUTHENTICATION,"simple");
env.put(Context.SECURITY_PRINCIPAL,adminName);
env.put(Context.SECURITY_CREDENTIALS,adminPassword);
ERROR :
Problem searching directory: javax.naming.CommunicationException: simple bind failed: testing.amg.com:636 [Root exception is java.net.SocketException: connection is closed]
Can any body please help me out how to overcome it.
waiting
Bye
Irshad

Packet Tracer 6.0 problem

How to open saved *.pka file on another PC? When I try I got message: "The file ... is not compatible for this version of Packet Tracer". I use version 6.0 on both PCs. Thank you.

It was a bug of version 6.0.1. Cisco says:
All NetAcad students using the student version of Cisco Packet Tracer (PT) 6.1 should upgrade to PT 6.1.1 as soon as possible. Version 6.1.1 contains an important fix to a bug and helps ensure the correct scoring of Packet Tracer Skills Assessments (PTSAs) in the CCNA Routing and Switching curriculum.
So I just upgraded my PT to version 6.1.1.

Problems Setting Up Developer Users

I am having a problem setting up developer users and I am trying to determine if I am missing a step or if there is a configuration problem on my staging and production systems.
What I want to do should be very simple. I want to create a user that can create an application and see the information under the "Application" tab in the Navigator.
I have created the user using the following steps on 3.0.9.82 for Unix:
1. Create the user
2. Make the user a full administrator (rather than end user)
3. Make the user a member of the portal_developers group
4. Make the user's default group the portal_developers group
However, when I do this the user does not see the information under the
"Application" tab. The only way I can get the user to see the info under the
"Application" tab is to make him a member of the Portal_administrators
and/or DBA group. Both my staging and production boxes have the same result.
Does anyone have any thoughts or suggestions on what might be happening?

Thank you- I have read through that thread and can see some resonance with my issue.
My AOL emails work VERY fast with BB, in fact almost simultaneously received on PC & Torch " ping ping!"
This issue only raised its ugly head when I had 2 Torches replaced by my insurers.
Whilst the claim was in process I used a new Curve, loaded from backup on PC to keep emails going and of course phone & web facilities. ( I use the BB to power internet via bluetooth to my PC / laptop when living on a remote island with no phone lines or power supplies) All was fine. Swapping email accounts took a few minutes with the usual password confirmations for each AOL screenname etc.
Then the new Torches came back from insurers, and I tried to swap devices. Phoning & texting is fine. Al data and contacts swap over fine.
SETUP email accounts.............stymied every time. It says repeatedly that my user name/password is invalid etc etc etc
Have tried security wipes. Have tried setting up new BB ID & passwords on PC website. All is OK until I try to setup emails on the Torches. This has used up ridiculous amounts of time- all wasted.
I love the BB phones and the fast email push......in fact I recently bought a new Sony Xperia Z1 but sent it back because of wifi coverage meant no emails on that superb phone for lots of the time.
Good old BB I said..........I always get emails wherever I am. ( Rural Scotland has very patchy radio & wifi coverage)
Was about to purchase new Z10s just to get a bigger screen, but now I am averse to buying ANY BB phone again because this present mess means I may never get emails set up again. How nuts is that?
Many thanks for all help & suggestions..........boy do I need them!!
Kind wishes from West of Scotland
Fair winds and kind landfalls

Problems setting up Mail to Exchange

Hey everyone,
Having a few problems setting up mail to exchange on a Nokia 5800.
We have the latest version of Mail to Exchange installed.
Were using Microsoft Exchange 2007.
Example serup of what we have done:
Mail to exchange - New profile - Input Username and Password of domain account - Input domain name - Chose Internet as means of connection -
The Nokia goes off and searches for the domain information, finds it OK. Shows a message regarding a server certificate, we chose to install this certificate this time only.
Phone crashes?
Any ideas whats going on?
Thansk

Hi Jim,
Depending on the customer feedback, it works fine. Apple Mail the client that comes with OSX supports standard protocols (POP3, IMAP, SMTP), these are all supported by Exchange 2010.
If you're running Mac OS 10.4 Tiger or Mac OS 10.5 Leopard, you can still use the Mac Mail App to connect to your account. However, you need to connect to your account without using IMAP or POP.
If you're running Mac OS 10.6 Snow Leopard or Mac OS 10.7 Lion, you can use the Mail program included with those releases to connect to your email account automatically using an Exchange account.
When you use Mac OS 10.6 Snow Leopard or Mac OS 10.7 Lion and connect using an Exchange account, you can use features that aren't available to users who connect through IMAP or POP, including iCal and Address Book.
More details about Set up email in Mac OS X Mail, please refer to:
https://support.office.microsoft.com/en-in/article/Set-up-email-in-Mac-OS-X-Mail-de372dc4-9648-4044-a76c-e8a60e178d54?CorrelationId=a0ce4c19-1492-4e3b-bc7e-4af83d3cb347&ui=en-US&rs=en-IN&ad=IN
Additional, I find a similar thread about your question, for your reference:
https://social.technet.microsoft.com/Forums/exchange/en-US/b112b61e-401f-4ad9-b459-a25673ff5407/connecting-to-exchange-2010-using-apple-mail?forum=exchange2010
https://social.technet.microsoft.com/Forums/en-US/d3c9b4ad-822b-4a7c-88b8-39df3f166f96/how-to-setup-exchange-account-on-macbook-os-x?forum=exchange2010
Best Regards,
Allen Wang

Problems setting up MPLS

A Chairde,
Am having problems setting up MPLS between a AS5350 and 7609 , I have used commands stated in this link, enable MPLS incrementally on a network.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/switch_c/xcprt4/xcdtagc.pdf
The commands below are added to each router, and some troubleshooting.
7609
ip cef distributed
interface Loopback0
ip address 192.168.254.1 255.255.255.255
tag-switching advertise-tags
interface GigabitEthernet3/12
ip address 192.168.230.162 255.255.255.248
mpls label protocol tdp
tag-switching ip
AS5350
ip cef
mpls label protocol tdp
tag-switching advertise-tags
interface Loopback0
ip address 192.168.254.2 255.255.255.255
interface FastEthernet0/0
ip address 192.168.230.161 255.255.255.248
duplex auto
speed auto
mpls ip
h323-gateway voip interface
h323-gateway voip id cnibhco111 ipaddr 192.168.230.129 1719
h323-gateway voip h323-id cnibhco112
h323-gateway voip tech-prefix 71401
h323-gateway voip tech-prefix 0030
h323-gateway voip bind srcaddr 192.168.230.161
ip rsvp bandwidth 64 64
cnibhco112#sh tag-switching tdp neighbor
Peer TDP Ident: 192.168.254.1:0; Local TDP Ident 192.168.230.161:0
TCP connection: 192.168.254.1.49842 - 192.168.230.161.711
State: Oper; PIEs sent/rcvd: 18/23; Downstream
Up time: 00:12:54
TDP discovery sources:
FastEthernet0/0, Src IP addr: 192.168.230.162
Addresses bound to peer TDP Ident:
192.168.100.17 192.168.100.25 159.107.212.49 172.16.8.81
192.168.230.130 192.168.230.77 192.168.230.81 192.168.254.1
192.168.210.6 192.168.127.6 192.168.210.106 192.168.127.66
192.168.127.138 192.168.210.146 192.168.210.142 192.168.210.122
192.168.210.17 192.168.230.140 192.168.230.26 192.168.230.74
192.168.230.10 192.168.230.14 192.168.127.130 192.168.127.142
192.168.230.6 192.168.230.70 192.168.230.34 192.168.210.178
192.168.200.25 192.168.210.126 192.168.232.1 192.168.231.1
192.168.200.17 192.168.210.102 190.168.200.245 190.168.200.225
190.168.201.241 192.168.230.98 192.168.210.14 190.168.201.201
190.168.201.209 192.168.210.162 192.168.210.210 190.168.201.205
192.168.230.38 190.168.200.249 190.168.200.217 190.168.200.253
192.168.230.162
cnibhco112#
cnibhco112#sh tag-switching forwarding-table 192.168.254.1 detail
Local Outgoing Prefix Bytes tag Outgoing Next Hop
tag tag or VC or Tunnel Id switched interface
cnibhco112#traceroute 192.168.254.1
Type escape sequence to abort.
Tracing the route to 192.168.254.1
1 192.168.230.162 0 msec 0 msec *
cnibhco112#traceroute 192.168.230.162
Type escape sequence to abort.
Tracing the route to 192.168.230.162
1 192.168.230.162 0 msec 0 msec *
cnibhco112#

Ro,
Thanks for the respone, have been playin, with MPLS for last few hours.
The routing between the loopbacks is now working, can PING 7609 Loopback from AS5350 ,and vice versa. (used static routes).
Having problem with TDP / LDP on routers,
mpls label protocol ldp / tdp command works correctly on both routers, but the
tag-switching tdp router-id Loopback0 force
command works on the 7609, but when I add it onto the AS5350 , the command "mpls ldp router-id Loopback0 force" appears on the startup script.
The opposite is true for the 7609 , you add MPLS LDP command, and TAG-SWITCHING command appears instead.
Any Ideas, as different configs of this leave me with forwarding table with both tags added, but not been able to ping the loopbacks !!!
When I can ping bot loopbacks, the OUTGOING TAG , disapears.....
Problem is LOOPBACK Commands on bot routers default to LDP (AS5350) , or TDP (7609). Any Ideas ...
mpls label protocol tdp
tag-switching tdp router-id Loopback0 force
mpls label protocol tdp
mpls ldp router-id Loopback0 force
cnibhco100#sh tag-switching forwarding-table 192.168.254.2 detail
Local Outgoing Prefix Bytes tag Outgoing Next Ho
tag tag or VC or Tunnel Id switched interface
18 17 192.168.254.0/24 0 Gi3/12 192.168.2
MAC/Encaps=14/18, MRU=1500, Tag Stack{17}
00097CA3293000127FCDBA808847 00011000
No output feature configured
Per-packet load-sharing
cnibhco100#traceroute 192.168.254.2
Type escape sequence to abort.
Tracing the route to 192.168.254.2
1 192.168.230.161 [MPLS: Label 17 Exp 0] 0 msec 0 msec 0 msec
2 192.168.230.162 0 msec 0 msec 0 msec
But no PINGING 192.168.254.2
cnibhco112#sh tag-switching forwarding-table 192.168.254.1 detail
Local Outgoing Prefix Bytes tag Outgoing Next Hop
tag tag or VC or Tunnel Id switched interface
17 18 192.168.254.0/24 1915668 Fa0/0 192.168.230.162
MAC/Encaps=14/18, MRU=1500, Tag Stack{18}
00127FCDBA8000097CA329308847 00012000
No output feature configured
Per-packet load-sharing
cnibhco100#sh tag-switching forwarding-table 192.168.254.2 detail
Local Outgoing Prefix Bytes tag Outgoing Next Ho
tag tag or VC or Tunnel Id switched interface
18 17 192.168.254.0/24 752551 Gi3/12 192.168.2
MAC/Encaps=14/18, MRU=1500, Tag Stack{17}
00097CA3293000127FCDBA808847 00011000
No output feature configured
Per-packet load-sharing
WHEN BOTH LOCAL AND OUTGOING TAG, CANNOT PING EITHER WAY !!!
HAVE LABEL PROTOCOL AND LOOPBACK FORCE on AS5350
HAVE LABEL PROTOCOL ON 7609
WHEN ADD LOOPBACK FORCE on 7609 , CAN PING BOTH LOOPBACKS,
BUT OUTGOING TAG DISAPEARS
cnibhco112#PING 192.168.254.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.254.2, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
cnibhco112#sh tag-switching forwarding-table 192.168.254.1 detail
Local Outgoing Prefix Bytes tag Outgoing Next Hop
tag tag or VC or Tunnel Id switched interface
17 Untagged 192.168.254.0/24 598678 Fa0/0 192.168.230.162
MAC/Encaps=0/0, MRU=1504, Tag Stack{}
No output feature configured
Per-packet load-sharing
cnibhco112#
mpls label protocol tdp
tag-switching tdp router-id Loopback0 force

Problems setting up used ipa2 with ios7 due to Find My My Ipad Feature being left on by previous owner

Hi!! Im having problems setting up a used ipad 2.with ios7. The previous owner forgot to turn off the find my ipad feature so now its asking me for her itunes username an password. I dont have that info and i lost her phone number

yes my friend ios 7 was already loaded on when i bought it. The person who sold it to me left the find my ipad feature ON. I called her and she said she would be in the next day to buy it back and since i actually belived her i threw away her phone number. i dont know what i was thinking

Problems setting up WRT54G2 router

I'm having problems setting up my Linksys WRT54G2 router. I want my mac laptop (iBook G3 running OSX) to use a wireless connection, and the home computer (running Windows XP) to stay connected to the modem.
I originally tried to set up the router by connecting it via ethernet to my laptop (and by ethernet to the modem), and went into the 192.168.1.1 address to configure it. The internet works fine on my laptop when connected to the wireless by ethernet but it can't connect wirelessly (it has an original airport card fitted, at first I thought I might need to upgrade the firmware but I ran a software update and one didn't come up). I then realised that I would need to MAC clone from the PC, that is connected to the modem? I tried to do this today, but I couldn't access the 192.168.1.1 address from the PC. I have tried resetting the router, and disabling the firewall but still can't access it. This PC also has anti-virus software running too - could this be the problem, or am I setting it up wrong? Thanks.

If you are trying to Setup your Router with the setup disk, Then you can exit from the setup and configure your Router manually. Before you configure your router, you need to Press and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your router, wait for 60 seconds and re-connect the power cable.....
You need to connect your Modem to Linksys Router on Internet Port and your Computer to Linksys Router on Port No.1.
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link
Here are the Wireless Settings which you can set on your router, once done you can try connecting your MAC computer to your Wireless network and check if you are Online from MAC computer.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
-Here select manual configuration...Wireless Network mode should be mixed...
-Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Wide-40MHz and change the Wide channel to 9 and Standard Channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on save settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select AES...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.
NOTE : Passphrase should be more that 8 characters...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304 Change the RTS Threshold to 2307 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

How to set up passwords for two Comcast email accounts on Mail?

Have Leopard. Cannot set up passwords on Mail for two Comcast email accounts. Does anyone know how to do?

Hi Paul, & a warm welcome!
Lineone
Login
[email protected]
Incoming email (IMAP)
imap.lineone.net
Incoming email (POP3)
pop3.lineone.net
Outgoing email (SMTP)
smtp.lineone.net
What port & Authentication are you using?
Can you login with your credentials in a Browser using the same info?
In Mail's Window Menu, choose Connection Doctor, any red dots for status, if so what is the exact message?
Then click the Show Details button & Check again.
The Password rejection can confuse people since it's a catch all meaning...
This Password, Username, Authentication method... is not recognized on this Port to this Server, or a server end problem.
If using a browser to login via WebMail works it's not Name or Password, but one of the other ones.
The receiving email ports are:
IMAP is port 143
IMAP-SSL is port 993
POP is port 110
POP-SSL is port 995
Outgoing ports are...
SMTP and SMTP-SSL is on ports 25, 587 and 465. Port 587 has to be SSL, and port 465 is enforced TLS-wrapped and is generally used by Outlook users.

JDeveloper problem setting up a database connection

I am having some problem setting up a connection to my database. Before I say any more let me explain what I need. I need 2 database connections 1 to a 10g R3 database and one to an 8.0.5.
I do realize that JDeveloper will only connect back to 8.1.7 because of the JDBC version that is installed with it.
What I really need to know is "Is it possible to define and use 2 different versions of JDBC" I really don't want to move back to the version that works with both because I am afraid of what performance/benefits I will lose from the latest and greatest.
The latest version that I can determine will work with 8.0.5 is the last version for 9i.
Any Ideas would be helpful.
The reason for this situation is that I have a production database that I will have to keep up with until the full version of the system is complete so that is why I even care about 8.0.5.
Thanks alot for your time,
Thom

I have a similar problem and I would much appreciate any help in this matter.
I have a wireless network set at home with two computers connected to it:
My workstation called Home-ws and my laptop called Acer. I can access the d:\ drive of my workstation from my laptop without any problem.
On my workstation I installed the Oracle 10g product and on my laptop I installed Oracle SQL Developer. On SQL developer I am trying to create a connection to the Oracle server:
My settings are as below:
Connection name: orcl_system
User name: system
Password: ******
Host name: Home-ws
Port: 1521
SID: orcl
When I push test I am getting the following error message:
Status: Failure –Io exception: The Network Adapter could not establish the connection
Are there any special settings that should be made set up a wireless connection to my database?
Then I did the following things below:
1. I downloaded from oracle.com the instantclient-basic-win32-10.2.0.2-20060508.zip file and unzipped it in a folder called instantclient_10_2. There were a number of DLL and two jar files plus sqlplus.exe
2. I started sqlplus from that server
3. sqlplus failed with a similar error as sql developer.
4. I checked for tnsping. There is no tnsping such and exe on my laptop. I looks like I have to install the DLLs I downloaded them but there are no instructions about how to install them. Should I just copy them in system32 folder?
5. I looked for firewalls on my Home-ws workstation (where my oracle server is installed) and on my Acer laptop. The firewalls were activated. I added on exception called oracle for port 1521 on both computers and tried to connect again. I tried with both TCP and UDP options and it did not work in both cases.
I am out of ideas. Any help would be much appreciated.
Thank you in advance for your help.
Julian

The ok button to set master password doesn't work. Why?

Almost scammed by TeamView supposedly from Microsoft. Went into my computer to fix event logs.Wanted $109.00 now then asked if I had partial payment. So my dilemma is I don't know if what little security I have has been compromised. Not very computer literate.
Installing Kaspersky today.
My problem with Mozilla - tried to set master password but ok button doesn't work. Not on at all. What can I do?
Thank you/

TeamView is the name of the program that the scammers used, not the company they are from. TeamView is a legit company, but the scammers are most likely not. For future reference, most legit companies will use a paid program for get remote access to your computer.
When setting a Master Password, your password needs to fill the quality meter before the ''Ok'' button will become active.
[https://support.mozilla.org/en-US/kb/use-master-password-protect-stored-logins?esab=a&s=master+passowrd&r=3&as=s Here] is an article for more information about the Master Password feature.

Problem setting vty password in packet tracer

Similar Messages

Maybe you are looking for