Problem with OSS note

Hello. I do not know if there is anybody in here that has encountered this problem but....
We have NEW GL activated so we have to use transaction FAGL_FC_VAL with program FAGL_FC_VALUATION for closing year and converting some documents from local currency to other currencies.
When I run the program, there is a error concerning string length:
Runtime Errors         READ_REPORT_LINE_TOO_LONG
Exceptn                CX_SY_READ_SRC_LINE_TOO_LONG.
I have looked for a SAP note that corrects this error. I have implemented it but still...there is no effect. Suggestions?
The error takes place in K_KKB_FIELDCAT_MERGE function at line 366.
I do not thing that trimming the variable from 75 to 72 chars is a solution.
Thank you,
Cristian.

Hi. I have looked for OSS notes for this error. There is a note 1013501 that say this is an programming error and it can be fixed with correction instruction 844370 or install package SAPKH50016.
Still, after implementing the correction instruction, it didn't work.
For the moment I do not want to install packages.
My system is 5.0. Retail configuration.
Could you tell me the line numbers of that code?
Edited by: Cristian Boartes on Dec 21, 2007 4:01 PM

Similar Messages

  • Problem with OSS note 1529649 - Factory calendar expires 2010

    Hi Experts,
    I found a OSS note that is telling that calendar validity ends in 2010.
    For the moment in my system factory calendar for all my sites is valid till 2020.
    My question is that doesn't matter what date i have now in the system the validity will finish?
    What i should do!!!
    Thanks a lot for your help.

    Dear
    If the factory calender and holady calendar which is assinged in FC , both have same validity , then there should not be any problem .
    For  consistency , you can go down to OP03-Slecet HC-Change Mode -Keep the valaidty along with all the public holday calander validity till 2011 or 2012 .Similarly , do the same in Factory calander  .
    But re-assing the Calander to Plant once again in OP03 -Plant Assingent tab  or re-assing at WC ( CR02-Capacity tab -Standard Avalaable Capacity )  also if you have similar kind of canalder also .
    Hope this helps
    Regards
    JH
    Edited by: Jiaul Haque on Dec 10, 2010 10:56 AM

  • When I plug in my ipod to my laptop instead of my desktop, nothing pops up to sync my ipod. Has anyone had a problem with itunes not recognizing an ipod?

    When I plug in my ipod to my laptop instead of my desktop, nothing pops up to sync it. Has anone had any problems with itunes not recognizing an ipod?

    Hi sarahdavis0_o,
    Welcome to the Apple Support Communities!
    If neither your iPod or iPhone are being recognized by iTunes when connected, I would recommend the steps in the following article.
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    Have a great day,
    Joe

  • HT5312 So I have a problem with iTunes not letting me download anything without first responding to some security questions which I don't remember setting up, how can fix it? Oh, and it won't let me reset the questions either!

    So I have a problem with iTunes not letting me download anything without first responding to some security questions which I don't remember setting up, how can fix it? Oh, and it won't let me reset the questions either!

    If you mean that you aren't getting the reset link, then from the page that you posted from :
    Note: The option to send an email to reset your security questions and answers will not be available if a rescue email address is not provided. You will need to contact iTunes Store support in order to do so. 
    You can contact iTunes Support in your country via this page : http://support.apple.com/kb/HT5699
    When they've been reset you can then use the steps half-way down the HT5312 page that you posted from to add a rescue email address for potential future use

  • We have version 10.5.8 photoshop CS3 for Mac. How do we fix a problem with photoshop not resizing dpi? For example we resized a 72 dpi image to 200 dpi, when we do a pdf analysis it read as 344 dpi.

    We have version 10.5.8 photoshop CS3 for Mac. How do we fix a problem with photoshop not resizing dpi? For example we resized a 72 dpi image to 200 dpi, when we do a pdf analysis it read as 344 dpi.

    Sounds like it's a problem with the Acrobat settings. Did you set them to the same resolution?

  • RFIDITVCL : problem with variation notes

    Hi Experts,
    I have implemented the sapnote 1639418 "RFIDITVCL: 3000 Euro Communication additional changes", but I have a problem with variation notes related to specific invoices in same year...the user guide in the note says that they are clubbed together and the total is compared with the limit...I think that the report doesn't function in this case (my case is higher 25000u20AC) and so my documents aren't in the list....
    Do you have the same problem??
    Thank you
    Best regards
    Angela

    Dear Angela,
    I have the same problem. The program looks at field BSEG-REBZG.
    However this field is empty in our case.
    We create our debit and credit memo's with reference to the original sales order.
    Who knows a solution?
    Roelie

  • I have ongoing problems with "application not responding" in various programmes, ie Word, Excel, Illustrator, Photoshop, iPhoto etc. I recently subscribed to CC but the problem still persists. Any advice please?

    I have ongoing problems with "application not responding" in various programmes, ie Word, Excel, Illustrator, Photoshop, iPhoto etc. I recently subscribed to CC but the problem still persists. Any advice please? This applies to my iMac and my macbook air! I'm using OSX Version 10.9.3

    Hi Shauneenb,
    Welcome to the Apple Support Communities!
    If you are having issues with multiple applications becoming unresponsive I would suggest the steps in the following article, including starting in safe mode.
    OS X Mavericks: If an app freezes or quits unexpectedly
    http://support.apple.com/kb/PH13975
    I hope this helps,   
    -Joe

  • I'm having constant problems with pages not working. I.E.: I cannot fill in writeable fields, click on buttons... or anything... nothing on the page works. And, this is not exclusive to a particular site. I can, however, work well in Explorer.

    For the last few weeks I have had constant problems with pages not working. I.E.: I cannot fill in writeable fields, click on buttons... or anything... nothing on the page works. And, this is not exclusive to a particular site. It does seem to be a browser issue, because I can work well in Explorer.

    Both the Yahoo! Toolbar extension and the Babylon extension have been reported to cause an issue like that. Disable or uninstall those add-ons.
    * https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

  • Problems with IE8 "not responding" on windows 7

    I have a Toshiba Satellite L-355  that has been upgraded to run Windows 7 Home Premium from Windows Vista. I've been having problems with IE8 "not responding" and have tried running it without add-ons, system restore, and banging my head against the wall. All to no avail. Does anybody have any ideas how to fix this? I've tried running other browsers with the same problems.

    Intel(R) HM55 Express Chipset LPC Interface Controller
    Thanks, sav! That's perfect. (Good to know it shows up in Device Manager for people, too.)
    Okay ... although it's the Intel P55 and PM55 chipsets which get all the press about cranky Touch/iPhone connections on Windows 7 systems (the 0xE0000065, -6999 and "Disk can not be read or written to" error messages are the most common, although symptoms can vary further than that), similar sorts of issues look like they could strike other Intel 5-series chipsets ... including your HM55.
    So I'm proceeding precisely as I would with someone with a PM55 chipset.
    *1) Dell updates*
    Some folks with 5-series chipset trouble have got past it by way of BIOS updates. So I thinks it's worth your heading to your Downloads page at Dell, and checking to see if there's any newer versions of your BIOS lurking there. Unfortunately, with the Studio 15s I'm never precisely sure which is the correct downloads page ... so I'd try going to the following Dell page:
    http://support.dell.com/support/downloads/index.aspx
    ... enter your service tag, and then drill through to your downloads page.
    Any improvement with your syncing performance after applying any available BIOS updates at Dell?
    *(2) Adjust power management setting on USB controllers*
    If no joy after updating (if you were behind on your BIOS version), try applying the measures from the following document:
    [iPod not recognized when connected to Windows laptop over USB|iPod not recognized when connected to Windows laptop over USB]
    Reboot the PC after making the changes, and then try another sync. Any improvement?
    (If either set of measures improves your sync performance, please post back to let us know which one helped for you.)

  • Anyone else haveing a problem with appointments not syncing, duplicate appointments when syncing with Outlook? Also, noticed that my primary SMTP disappeared, and I had to re-establish to send e-mail. Apple tech support was worthless.

    Anyone else haveing a problem with appointments not syncing, duplicate appointments when syncing with Outlook? Noticed the problem a couple of days ago.
    Also, noticed that my primary SMTP disappeared, and I had to re-establish to send e-mail.
    Apple tech support was worthless on both issues.

    Hi I am also in the UK, but not with Tiscali and am having the exact same problems. I can also send with wifi, but not 3G. I have tried amending all sorts of settings, including those above and amending the smtp server to the settings for my provider, but all to no avail.
    It is thoroughly frustrating, as I cannot send emails unless I have wifi access.
    Any further suggestions would be very welcome.

  • I still am having problems with Aperture not loading,  It just refuses to work, and I get the message saying it has encountered a problem, and I may need to re-install which I have done dozens of times. The fix mentioned on an earlier post wont work as it

    I still am having problems with Aperture not loading,  It just refuses to work, and I get the message saying it has encountered a problem, and I may need to re-install which I have done dozens of times. The fix mentioned on an earlier post doesn't work as it is for Ver 10.6.6 and I am running 10.6.7

    Do you have Final Cut installed on your machine?
    If so, you may want to look at this article: http://support.apple.com/kb/TS3528
    Let us know if that helps.

  • Problem with windows not liking any files named prn

    I recently found a problem with windows not liking any files
    called prn.html, prn.cfm etc etc. If you try and create a file like
    prn.html then it will say "File already exists".
    I initially thought it was a Cold Fusion error as I was
    getting some bizarre error messages when trying to write prn.html
    using cffile.
    Does anyone know a work around for it?

    Hi,
    Not only "prn" but also for the terms like "AUX", "NUL" you
    can't create any directories or files in Windows because these are
    reserved terms with Windows which is meant for some device
    drivers...

  • Problem with Internal Note

    Hi All,
    Here is the problem,
    Whenever an approver adds a note to the Shopping Cart, the notes and the time stamp are not properly aligned or in other words, the notes added and the time-stamp which is generated along with it are not in continous line , does anybody have answer to this ??
    Thanks

    Hi
    <b>Please go through the follwoing SAP OSS Notes -></b>
    Note 491781 - ITS updates in Release 6.20 (Composite OSS Note)
    Note 890601 - SAP Integrated ITS updates for NetWeaver 2004s (7.00)
    Note 721993 - ITS updates in Release 6.40 (SAP Integrated ITS)
    Note 987640 - Text Editor missing under documents tab for all BO
    Note 768063 - ITS TextEdit: Cursor cannot be set in read-only mode
    Note 854381 - SITSPMON: The Mutex statistics only correct after a refresh
    Note 791674 - ITS: siac_upload, siac_publish, lang.-dep. templates, screen
    Note 788798 - ITS TextEdit: Incorrect forward navigation in ABAP Editor
    Note 839814 - ITS: Internet Explorer help opens with F key [F1]
    Hope this will help.
    Regards
    - Atul

  • Problems with program not finding Fonts

    Problems with Fonts on new iMac.
    I'm not sure if this is a problem because I switched to Snow Leopard or because I ported all my information using Migration assistant to the new iMac.
    Every time I open Firefox 3.6, I get the same annoying popup messages that Firefox can't find Arial and Times New Roman and wants to allow Firefox to use those fonts on my backup hard drive (which is actually the hard drive I was running Leopard on on my previous computer) I have checked my new computer, and yes the fonts are installed on my new computer. I have used FontBook to resolve duplicate fonts. When I tried to search on Firefox issues, people have problems with the wrong fonts rendering on the screen, which I don't have. For some reason, Firefox is looking in the wrong place. I don't think this is a Firefox issue, as I'm running the same version of Firefox on the new computer as I did on the old computer and I didn't have any problems on the old computer. Is there anything I should be checking in FontBook to make this problem go away?

    Can't address your FireFox issues, since I use Safari and these forums are for solving issues with Apple's products. You might try the FireFox forums. Additionally, give Font Management in OS X a look see.

  • Problem with data not displaying in website

    Hello All,
       I am having a problem with one of our applications. It is written in ColdFusion and uses SQL server. The problem that we are having is when we use the URL Http://bma.com (that is not actually the site name)  we cannot see all the data that it is suppose to pull in. I get an error on page and when I select to view the error this is what I get
    Message: 'WddxRecordset' is undefined Line: 184 Char: 2 Code: 0 URI: http://bma.com/user_maintenance.cfm and Message: 'jsusersTLV' is undefined Line: 3208 Char: 6 Code: 0 URI: http://bma.com/user_maintenance.cfm
    If I put the IP address in the URL for example http://165.83.109.246/bma/login.cfm all of the data is displayed as it should.
    Any thoughts or sugguestios on how to correct this?
    Thanks

    Yes, the user_maintenance.cfm is one of the forms that the data is not displaying on. There are multiple forms in the application and that just happens to be one of them. the login.cfm is just the login screen. Once you select your name and enter your password to the application then you can select the user maintenance form. If you select someones name the application should pull in all of that persons information. That is the problem, it is not pulling in any information on the user. We get a blank screen where data should be. When we use the IP address in the URL and select someones name in the user manintenance form, it pulls in all the data from that user as it should.

Maybe you are looking for