PS3 and wireless connectivity issue

I apologize ahead of time for what I am sure is a repeat question.
I am operating with Windows 7, a Linxsys WRT 400N router connected to a Comcast cable modem. The PS3 gets all the way to the end of the set-up and during the check it fails and states "the key information timed out". I am getting a 95% reading during the process but not hooking up. So far I have, disconnected the router and modem and reset the PS3 to original settings. I have been trying the easy walk through on the PS3. WPA encryption on the router.
Advice please.
Thanks,
Rob

Are you able to go online through the router...?
If you are not online through the router then,configure the router first..Check this link to configure the router.Once the router is configure,follow the settings for the PS3.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
On the set-up tab change the MTU Size to 1365 and click Save Settings...Click on "Administration" tab and disable the option UPnP and click Save Settings...Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 80 and End box type in 80, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in DEF, in the start box type in 443 and End box type in 443, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in GHI, in the start box type in 5223 and End box type in 5223, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
4) On the fourth line in Application box type in JKL, in the start box type in 3478 and End box type in 3479, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
5) On the fifth line in Application box type in MNO, in the start box type in 3658 and End box type in 3658, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
6) On the sixth line in Application box type in PQR, in the start box type in 10070 and End box type in 10080, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings
7) Now assign the given ip address on your PlayStation ip address :- 192.168.1.20, subnet mask :- 255.255.255.0, default gateway :- 192.168.1.1...
8) Also assign the dns addresses on the PlayStation Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
9) Turn off your modem, router, and PlayStation...Wait for a minute...
10) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the PlayStation and test it...

Similar Messages

Airport Extreme, PS3 and Netflix connectivity issue.

Up until a few months ago my setup was working fine to stream Netflix over my PS3, now I am unable to stream netflix on my PS3 when connected to my Airport. Before you jump to the conclusion that the PSN outage is the root cause of my current issues let me assure you that is not the case.
1. I am connected via ethernet (not wirelessly, although that does not work either for the record).
2. I have updated my PSN password and am able to connect and use other services (such as multiplayer games) successfully.
3. I can use netflix on any of my other computers connected to the same Airport without issues (wired or wireless).
When I connect the PS3 directly to my modem everything works fine, netflix connects and I can play anything I could before. As soon as I connect my Airport between my modem and my PS3 the ability to use netflix disappears.
I have attempted port forwarding (80 and 443).
I have NAT Port Mapping enabled.
I have tried setting the PS3 up with a static IP and enabled it as the default host (DMZ).
I have tried connecting wirelessly.
I have tried changing the MTU on the PS3 to 1492 (a suggestion from another forum).
I have tried power cycling all the equipment.
I have even tried resetting my Airport to factory defaults, all with no luck.
Is anyone else experiencing this issue? I have seen a few other threads from last year dealing with the Xbox360 but nothing current. This is driving me crazy as we have been without netflix now for months. Any help or suggestion that I have not tried???

Welcome to the discussions!
Is your Netgear a simple modem (it will have only one ethernet port) or is it a gateway (combination modem & router with 3-4 ethernet ports)?
If your Netgear is a gateway, as I suspect, have you configured the AirPort Extreme as a "bridge" so that it will function correctly on the network?
AirPort Utility > Manual Setup > Internet icon > Connection Sharing = Off (Bridge Mode)
Might be a good idea to check your ethernet cable as well. It should connect from one of the LAN <-> ports on the Netgear gateway to the WAN (circle icon) port on the AirPort Extreme.
Message was edited by: Bob Timmons

I am having wireless connectivity issues with my time capsule

Over the last 3 days my wireless devices have been having issues with connectivity.
Network setup:
Modem - Motorola SB5102 Cable Modem
1 TB Time Capsule 802.11n (second generation)
The devices are approximately 3 feet apart.
Wired Device:
Mac Pro (2008 build) running OSX 10.6.8, Airport Utility 5.6.1
Wireless Devices:
Playstation 3
Macbook Air
iPhone 5c
iPhone 4
I am having issues with internet connectivity. The wireless signal strength is fine as all devices can find the network. However when connected to the network accessing the internet on the Macbook Air, or either iPhone is slow and streaming services such as Netflix cannot connect. I have intermitant connectivity to the Playstation Network on the PS3.
I have wired both the Macbook Air and PS3 directly to the Time Capsule and have no issues, internet is accessible and streaming services are fine.
I have power cycled all the devices (Time Capsule, macbook, iphones, PS3, modem) to no result.
I am looking for any other suggestions that may help me with my wireless connectivity issue.

A Gen2 TC is probably on its last gasp.. and it is well overdue for replacement.
If you want to get more life out of it you normally need to repair or replace the internal power supply.. This is not done by apple or any of their repair centres.
Just do ebay search and you will find sellers with replacement supplies.
Otherwise to test, do a full factory reset..
I would also downgrade the firmware.. 7.5.2 will work just as well for you and has less bugs than 7.6.x firmware.
To downgrade hold down the option key when you select firmware version.
The Factory Reset universal
Unplug your TC/AE. Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. The time is not important.. it is the front LED rapid flashing that indicates you are in factory mode.
Release reset.
If it doesn’t flash rapidly you have released reset at some point and try again.
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.

I have a new Macbook Air 2012, Apple TV 2 and I have tried wired and wireless connections both result in stuttering during video airplay to the ATV2.

I have a new Macbook Air 2012, Apple TV 2 and I have tried wired and wireless connections both still result in stuttering during video airplay to the ATV2.
I have even bought a new Airport Extreme Router just to confirm it is not the router and it still didn't help.
I have brought all items in the same room with wired connections and still same issue.
I was thinking maybe ATV 3 might help since it has 2 wifi antennas and faster processor.
Have tried everything I could think of.
This was one of the main reasons I bought a Macbook Air for this airplay feature. Very frustrated.
Any thoughts; any other suggestions would be greatly appreciated.
Thanks

Thanks for the suggestion.
I also disabled Norton Firewall and restarted the Air and Now I'm able to use Air Play.
I know that the Apple remedy said that to do that in the support article, but I totally forgot I had that enabled..
It actually works. I can even stream to the Apple TV now through my MacBook Air.
BTW, Go into setting under the ATV, and click on update...you'll see that there was another update avaialble for the last gen of ATV...
It does have to restart twice..I guess once to download and and nother to apply.

A very strange wired and wireless network issue

Hello,
I have never had any issue at all with my macbook (2008) until this week, I use it both for work and personal use.
Most of time, I'm used to be on customer site, so I use wired and wireless connections depending of the situation....
I have never had any issue at all with wifi neither ethernet connections during three years, until this week... and I can say this is the most strange thing I have ever seen....
Using wired or wireless connection, always the speed of network was really good, at home, many customers, etc never had any problem...
But this week I'm currently out of home, and the hotel where I'm staying I'm having very poor network rate....
Using wireless connection, the download speed is no more than 10kb.... and using ethernet I get less speed... but during the day I'm on customer site, using the ethernet connection and download speed is really good, more than 500k-800k....
I have already tried in the hotel few wifi connections (there are three) and differents wired connections (in diferent rooms) and the download speed is always the same, no more than 10kb...
During this afternoon, I could go into hotel's lab and could connect directly to the router using cable, same speed no more than 10kb....
The most strange thing is on their computers the download speed using wired connection is around 6Mb....
how is possible I'm getting no more than 10kb of download speed when the pc's at hotel using same wired connection gets 6Mb?
I have already deleted current network connections, execute onyx to clear everything, perform dhcp connection, tried manual ip etc, and always the results are the same...
I know there is no problem with the macbook, because it works pretty good at every location I've been... but until this week...
Sincerely I'm getting a little crazy here, I'll appreciate any help!!!
thanks in advance

I've seen something like this on my T400 when it was running Vista. Now that I use Win 7 it's been OK. I rather doubt that your issue is the same but I'm tossing it out here just on the off chance.
Im my case, I had to downgrade my Intel 5300 card to a 5100 (as suggested by a Lenovo 2nd-tier tech) to get things working.
My symptoms were a little different. Wifi was fine until I went back to a wired network. After that, trying to use the same wifi AP as before would end up associated, but no internet access. DHCP wasn't working. The GUI "find" app didn't work as expected either. Some APs showed up, and some didn't.
If I configured for automatic connection to my home AP it would try and fail. Just rebooting at that point would again attempt an automatic connection that would succeed.
What I have noticed now that I run Win 7 is that Access Connections is completely useless. Often the "finder" doesn't show an AP 3 feet away. I didn't notice that this happened after a switch from wired, but maybe.
Are you using Access Connections? If so, you might try uninstalling it.
Sorry I can't be of real help,
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

PS3 80GB Wireless Connection Help

We are struggling to get our 80GB PS3 to wirelessly connect to our Wireless-G Router.
It is set up using a WPA Security. Some one please help! We have done custom set up and put in our IP addresses on our on and we have done easy! The only way we can think of to make it easier is to take the security code off and have an unsecured network, and I do not want to do that.
Please help before I break my ps3 or my router LOL
Message Edited by Dawn7246 on 09-15-2008 01:59 PM

I reset my linksys router and all of a sudden the ps3 is connected to the internet. I dont know what it did, but it works!!!

Satellite U940 PSU6VA - Wireless connectivity issues

_*My specifications:*_
*Model:* Toshiba Ultrabook (Satellite U940 PSU6VA-00S002)
*Operating System:* Windows 8.1 x64 (upgraded from Windows 8 x64)
*Wireless adapter:* Intel(R) Centrino(R) Wireless-N 2200
*Wireless adapter driver version:* 15.10.0.12 (which is the latest for my device)
I have had this Ultrabook since February 2013, and throughout that period I have always had wireless connectivity issues, even after performing a factory reset. My wireless icon fluctuates between three states:
* Internet access
* Limited (in which case I cannot connect to the internet or any device on the network)
* Not connected - connections are available (and if I try to make it connect to the network, it will fail)
Sometimes my computer would instantly reach the "Internet access" state upon startup, and would remain in that state. Other times, it would be "Limited" for several minutes after starting up my computer before it finally connected, and even then the connection would drop out every now and then. At the worst, it would remain either "Limited" or "Not connected" indefinitely, no matter how many times I reset my wireless adapter or restarted my computer.
Until recently, I had always thought that these issues occurred randomly. However, I recently noticed that I always have a perfect connection whenever there are no other computers connected wirelessly to my home router, and I always experience issues of varying degrees when there is at least one other computer (or even a smartphone) connected wirelessly to the router. If there is another computer connected to the router via an Ethernet cable, this does not cause any problems; it is only wireless connections that interfere with my computer.
It is only this computer that has these problems; the other computers in my house never experience these issues, no matter how many computers are online. Also, my computer does not only experience these issues with my home router; it has the same issues on my university's wireless network.
My question is, how can I fix this? Is this a known bug, or is my wireless adapter defective? I know I can connect using an Ethernet cable where possible (I never have problems with Ethernet connections), but this is not always possible at university.

> {quote:title=TomDexter wrote:}{quote}
> Intel page provides the Wlan driver for this WLan card and its v16.7.0 for Win 8.1
I just checked the page you linked to, but it recommends that laptop users obtain their drivers from their OEM rather than from Intel.
I had already checked for driver updates through both Toshiba Service Station and Device Manager (and checked both again just now). Toshiba Service Station tells me that there are no updates available, and Device Manager tells me that "the driver software for your device is up to date".
Should I update to Intel's latest driver anyway? If so, should I also install the Windows 8.1 version of "Intel PROSet/Wireless Wifi Software"?
> {quote:title=TomDexter wrote:}{quote}
> I would recommend you to check the Wlan functionality and performance testing each Wlan standard 802.11 B / G and N and additionally check the different Wlan channels (1-11)
I have found the WLAN channel setting in Device Manager and I will test it when I get the chance. But how do I change the WLAN standard?
Message was edited by: Justinian

How to set up WRT54GS so the wired and wireless connections both work?

I have a DSL line in to a Motorola modem.
The modem is connected to the WRT54GS with an ethernet cable.
When I connect my computers directly into the WRT54GS with an ethernet cable (there are four connection spots at the back of the box), I cannot go to the internet. I have 3 computers plugged in, but none of them connect via Ethernet..
Is there a setting on the router so that I can use the router for both wired and wireless connectivity?
Added info: I tried to connect directly from the computer to the modem, but again, got no connectivity. When I "chatted" with ATT, they told me the modem is set to "bridge", and that I could connect only one device. I don't want to change this setting because I want to use the router for the wireless capability. Besides which, I have more than one computer to connect to the internet.
How come I cannot just plug in and go?
My firmware version is v2.07.1.
I don't know how to find out what hardware version I have.
Other info is "DirectEthernet Connection, Speed: 100.0 Mbps, Signal Strength: Excellent, Status: Connected"
Also "1394 Connection 3, Speed: 400.0 Mbps, Status: Connected"
I don't know what that's for, but thought it might prove useful to those of you who are knowledgeable about such things.
Wireless is ok, but if I'm sitting right next to the router, I'd like to connect with Ethernet and take advantage of the better speed, etc.
Thanks in advance.

Just click this link.

I have an existing new belkin modem router which works fine with quite a few wired and wireless products in my house. My question is if i buy a time capsule can i put it in another room and wirelessly connect it to the belkin modem router, I would then ju

I have an existing new belkin modem router which works fine with quiet a few wired and wireless products in my house. My question is if i buy a time capsule can i put it in another room and wirelessly connect it to the belkin modem router, I would then just like my macbook pro and (imac future purchase) to wirelessly back up to it???????????

Your will need to perform a Factory Default Reset on the TIme Capsule to clear out the current network settings and then reconfigure it to "join" your wireless network using the AirPort Utility setup application.
To perform the Factory Default Reset on the Time Capsule....
Pull the power cord from the back of the device
Wait a few moments
Hold in the reset button on the back of the Time Capsule and keep holding it an additional 8-10 seconds while you simultaneously plug the power cord back in to the Time Capsule
Release the reset button after the hold period and allow 25-30 seconds for the Time Capsule to restart to a slow, blinking amber light
On your Mac.....
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click Continue
Follow the guided setup and choose the "join" option when it appears duriing the setup
You will need to know the exact type of wireless security that the Belkin router is using to enter this information during the setup of the Belkin. Otherwise, the Time Capsule cannot join the network, and you will receive an error message after the configuration process.

Wireless connectivity issues with Macbook Pro and At&t service HELP!!!!!

I have three Computers two PC's and one Macbook Pro( the latest model).My desktop PC is used by ethernet, my girls laptop is used wirelessly and finally my MBP was being used wirelessly.
I started off with only the two PCs and my internet connection never had a problem and I was doing everything from: on the internet to downloading.
Before I bought my MBP I had also switched from internet and phone bundle to just internet from At&t service. So when I got my first MBP I notice that I was loosing wireless connection with both my girls pc laptop and my MBP so i thought it was because I had just switched service, though they send out a service technician and we came to a conclusion that it was the MBP. (I was loosing signal via wireless and ethernet). So we tried to see if both my girls laptop(wireless) and my PC desktop (ethernet) would run into the same issue which it did not.(MBP was turned off)
So I decided to go my nearest Apple store and let them know what was going on. So I told them what was going on and they said It must be the airport card, and they ended up changing it. When I get home I discover that not only I am having the same issue but other issues too. I went back they ran some diagnostic and they said it was defective and they gave me a new one few days later.
So in the mean time that I waited for my new one to arrive I used my PC desktop and my girl kept using her laptop and guess what no issue what so ever for one whole week. Now I receive my new MBP(they bumped the specs a little), went home set it up and still the same issue though I dont have the issue when Im using via ethernet. Just a view minutes ago I tried removing the ethernet and using the airport/wireless and within a few minutes I lost the signal.
I have the gateway 2WIRE model(2701HG-B) modem/router.
Is there something wrong? what do I have to do to make this work?

Hi Guys, I bough my Mac almost two years ago. All this time I have experienced the same issue. There are tons of discussions re this issue in the internet. Unfortunately, Apple has done nothing to fix it. I have tried a lot of different options, but they work no longer then 1-2 days. The official fix - does not exist so far. It is quit strange, isn't? I can share my experience: if you go to AirPort Utility - Manual Setup - Wireless and then change Channel, it could help you till the moment you restart your computer; next time you need to repeat it again. It takes 2 minutes. Not sure that it would work for you but you could give it a try. Well, not the best option. Anyway Apple must fix it asap! Hello Apple, do you hear us? Good luck.

Wireless connection issues

I have read extensively on this problem and it seems others have the same issue, however I will fully document the problem I have here and will also be sending this to apple as a bug report.
I have a Macbook Pro (3.1) running leopard 10.5.4 however these issues have occurred since 10.5.2 from memory, it may have been after an airport update but I wasn't using wireless around the time I updated. The router I have issues with is a Zyxel P660HW-T1, on which I have updated to the latest firmware (which isn't that new). Since an update I cannot connect to the router when using WPA encryption. This includes WPA-PSK and WPA2-PSK, on any wireless channel. The console errors when connecting are:
Aug 10 12:33:20 Nicks-Mac kernel[0]: AirPort: Link Up on en1
Aug 10 12:33:27 Nicks-Mac airportd[347]: Error: Apple80211Associate() failed -6
Aug 10 12:33:27 Nicks-Mac SystemUIServer[135]: Error: airportd MIG failed = -6 ((null)) (port = 55559)
Aug 10 12:33:27 Nicks-Mac airportd[347]: Error: processcommanddict() failed
Aug 10 12:33:27 Nicks-Mac SystemUIServer[135]: Error joining BroW: Connection timeout (-6 timeout connecting)
When connecting, the menu bar icon appears connected for a short time and then disconnects and the dialog box reports 'Connection Timeout'. Since this problem occurs I have reformatted the computer, reset the PMU and PRAM, and successfully connected to many other wireless networks using encryption. I have tried connecting to the network using windows in boot camp, and it doesn't work there either so the issue is firmware related. There were no issues before the update.
I have successfully connected to the wireless network using many other devices, including windows and linux computers, and windows mobile devices. Interestingly an iPod Touch exhibits the same problem; it used to work and now doesn't.
While I know buying a new router or Zyxel releasing a firmware update would resolve the issue, I feel that because it works with standard PC devices it is apple that should be resolving this problem as they created it. This router was one of the most popular on the store I bought it from here in the UK, and so it should be a fairly big issue. If the problem has been created due to a security hole in the WPA protocol being plugged, or something similar to this, it is understandable. Official word from Apple is needed on this!

William Kucharski wrote:
You won't get official word here; it's just users here.
I know, I wasn't hoping for official support or in fact any kind of help, I was posting this more as information for other users. I will be submitting it as a bug report in the hope it will be recognised officially. I don't think there is anything I can do that will resolve this.
As far as the connection goes, if it was truly the router at fault it wouldn't be Apple's problem to fix, as Apple codes their drivers to comply with recognized wireless standards and it isn't Apple's responsibility to write their code to accomodate routers that don't.
As I said it would be understandable if this was caused due to a bug fix in the protocol by apple and I would not expect a fix. That's the information I'm hoping for but doubt I will get. Having said this, think about it from the end users point of view. In terms of 'Just works', Mac 0 PC 1.
That having been said, you know from your experience connecting with other routers that it's not a blanket bug, so the next question would be what's different about your network that is causing these connection failures.
One thing to try is to try removing all known networks from your known networks in your Network preference pane, and add them back.
As I said, this is an issue with Apple devices, and seems to be a firmware and not a software issue. I have reformatted and tried connecting in windows, had the same problem with an iPod touch and a Macbook.
Message was edited by: Nick Brook

HP Officejet Pro 8500 a910 wireless connectivity issues?

I have a HP Officejet Pro 8500 a910 and It was working fine. I got a new router and it was still working fine. Second night of having everything set up it stops working and shows as offline on my computer. It will print information about the printer from thecomputor but will not print out any other documents.

I'm having the same issues. In my case, first I updated my MacBook Pro to OS X 10 Mavericks. A few days ago, the Actiontec gateway router provided by my ISP Frontier Communications ceased to function. Frontier sent a Netgear 7550 gateway router to replace it. I installed it according to directions. My email capability and home network went down. Frontier helped to restore the email but the techs I worked with couldn't figure out what to do to restore my wireless network. The router's setup would not allow me to replace the WPA Shared Key with the wireless network password I used previously. So, I updated the ASUS range extender and all the wireless devices that were on my home network with the new WPA key. Both printers, the Officejet Pro 8500A 910 and a Brother wireless laser, will not network. The Officejet blue wireless icon no longer lights up. I uninstalled the Officejet's software and then downloaded and installed the latest software and drivers for the Officejet Pro 8500A 910. The HP Network Configuration printout indicates that its network status is ready and the active connection type is wireless. I had it connected to my Mac with a USB cable so I could reinstall the software and drivers. When I disconnected the cable, I lost connection to the Officejet and couldn't print. the HP utility could not establish a wireless connection even though I did input all the new router settings. The Officejet thinks it's wireless but it isn't. I can only conclude that my Officjet is delusional. It's not all that old, but could it be ready for the all-in-one graveyard?

HP Officejet 6600 e-All-in-One Wireless connection issue.

We are using the HP 6600 now for 6 months and sice a few weeks we have some issues with the printer.
situation:
1 - HP 6600 printer
1 - Wireless Router
3 - Computers connected to the router
What we did:
Updated the firmware
Manual IP
Put channel from router to 11
Put it closer to the router (1 meter instead of 3)
HP docter, everything is fine (if connection is lost, answer "No network connection to your device"
But all above is not the solution.
When the printer is offline we just switch it off and on and it will work again for a couple of hours. It looks that the connection is lost when it is going to sleep/hybernate.
Also one of my customers has exactly the same problem, also did all above and didnt fix anything. This question is for me quite urgent because i am going on holidays in 2 days, my father in LAW cannot work without the printer and is getting upset this all this.
Any advices?

Arjan_NL
If I understand you correctly the printers blue light is flashing and you cannot see your printer on the network. I recommend that you reset the network defaults to factory settings on the printer.
To reset the network defaults
-touch Setup Menu
-touch Network
-touch Restore Network Defaults
Then use the Wireless Setup Wizard to connect the printer to the network.
To run wireless setup
-touch Setup
-touch Network
-touch Wireless Setup Wizard
follow the on screen instructions to set the printer up on the network. You will need the WPA password or security key for the router to do this.
Follow the steps in this document Printer Does Not Maintain Wireless Connection to set a static IP address for the printer. This should help you maintain a better wireless connection.
Keep me posted and let me know if you need further assistance.
I worked on behalf of HP.

PRINTER WIRELESS CONNECTION ISSUE

PRINTER 3050A All IN ONE Printer Scanner Fax
prints well with USB Connection BUT doesn't print on ePrint or Wireless, THOUGH the lights indicate there is positive connection. Error MSG: "Printer is Offline" but HP Printer screen indicates Online as do all ligths on printer. I've used the Router WSB reset and have completely shut the printer down, unplugged it and resumed in more than an hour. No change.

Hi @LITTLEBOYBLUE,
Welcome to the HP Support Forums! I see you are not able to print wirelessly to your HP Deskjet 3050A, when you attempt to print wirelessly, you get a 'Printer Offline' error message. You have 2 options when setting up your DJ 3050A to your network, you can use the HP's Auto Wireless Connect or do a USB to Wireless conversion. To get started click on the link below:
Setting Up the Printer for a Wireless Network for the HP Deskjet 3050A and 3070A e-All-in-One Printe...
Please let me know if you were able to connect your HP DJ 3050A to your Wireless network successfully.
Thanks,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Windows 8 And Random Connectivity Issues

Hello,
I just relatively recently got a laptop with Windows 8 on it. I hadn't used Windows 8 before, but while some features are good, others are not.
Notably, when I put my computer to sleep and return from sleep, often times I need to unplug my ethernet cable or my pages won't 'load' because the network is unavailable. But my old laptop, with Windows 7, will be able to access the internet just fine and
so it doesn't seem to be an ISP issue.
I thought it may be a Google Chrome issue, but IE and Firefox have similar issues, pages hang for a long time and eventually display 'page cannot be displayed' or some variant.
As I said, sometimes if I unplug and re-plug my ethernet cable in, it resolves it, at least when I return from hibernation.
Unfortunately, two or three times before, and now another time today, I'll be working on my computer and I'll go to a website and it will just hang, then if I try to reload or reload any other pages, I get a similar issue, the network isn't available.
I tried unplugging/replugging, I made sure the connection was fine by using my old laptop, and I even tried putting the computer to sleep and back, and closing Chrome and reloading, none of that worked. What did work was completely restarting, but this is
inconvenient.
I'm just wondering if anyone else has encountered these issues and if there are easier/more permanent fixes to them? They aren't /terrible/ but they are inconvenient and annoying.

Hi,
Have we tried the network troubleshooter?
Open the Network troubleshooter by swiping in from the right edge of the screen, tapping
Search (or if you're using a mouse, pointing to the upper-right corner of the screen, moving the mouse pointer down, and then clicking
Search), entering network troubleshooter in the search box, tapping or clicking
Settings, and then tapping or clicking Identify and repair network problems.
For more information regarding wire and wireless problems in Windows 8/8.1, we may first take a look at the following tutorial:
Wired and wireless network problems
Best regards
Michael Shao
TechNet Community Support

PS3 and wireless connectivity issue

Similar Messages

Maybe you are looking for