Radio subinterfaces and # SSID

Hi,
I have Cisco AP350 with IOS software witch doesn't allow to broadcast more that one SSID. BUT according to this document:
http://www.cisco.com/en/US/products/ps5853/products_configuration_guide_chapter09186a008045830f.html#wp999807
it is possible to make subinterfaces with different VLAN encapsulation and assign different SSID for each VLAN.
So my question : can i deploy this with my AP? or the early mentioned limitation is related to the AP350 itself?
Think you in advance

"encapsulation dot1q 2" means dot1q encapsulation enabled on VLAN 2.
"encapsulation dot1q 111" means dot1q encapsulation enabled on VLAN 111

Similar Messages

Base Radio Mac and SSID MAC addresses

I am looking for a way to obtain the SSID mac addresses from a report or other method. We have clients attaching to an SSID that show a MAC address that I am positive is the MAC of the SSID (based off the physical MAC of the Radio) but I cannot find it either in reports in WCS or on the controller.
Thanks!

try the following command via the CLI
show dot11 bssid
Examples
This example shows how to display a list of BSSIDs and SSIDs:
AP# show dot11 bssid
This example shows the command output:
AP1230#show dot11 bssid
Interface BSSID Guest SSID
Dot11Radio1 0011.2161.b7c0 Yes tsunami
Dot11Radio0 0005.9a3e.7c0f Yes WPA2-TLS-g
from this doc
http://www.cisco.com/en/US/docs/wireless/access_point/12.3_4_JA/command/reference/cr34main.html#wp2701427
let me know if this helps
Bill

Cisco 877w -Configuration of subinterfaces and main interface within the same bridge group is not permitted

Hi,
I have another problem - after upgrade ios wirelles connection not work.
After reload i have :
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
STP: Unable to get the port parameters.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
SETUP: new interface NVI0 placed in "shutdown" state
my old configuration work propertly in the old software, but after update i have notificatio.
Old thread:
https://supportforums.cisco.com/discussion/12379491/cisco-877w-no-wireless-connection
my current sh run:
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
service password-encryption
hostname cisco
boot-start-marker
boot system flash:c870-advipservicesk9-mz.124-24.T6.bin
boot-end-marker
logging message-counter syslog
logging buffered 4096 informational
enable secret 5 $1$eCNp$rWuBfZ/cexnwnkm7L447s.
aaa new-model
aaa session-id common
dot11 syslog
dot11 ssid ciscowifi
vlan 1
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 050D031D26595D0617
dot11 wpa handshake timeout 500
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.56.1
ip dhcp pool CLIENT
import all
network 192.168.56.0 255.255.255.0
default-router 192.168.56.1
dns-server 8.8.8.8 194.204.159.1 194.204.152.34
lease 0 2
ip cef
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
username marek password 7 00121A0908500A
archive
log config
hidekeys
ip tcp path-mtu-discovery
bridge irb
interface ATM0
description Polaczenie ADSL do ISP$ES_WAN$
no ip address
no atm ilmi-keepalive
pvc 0/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
hold-queue 224 in
interface FastEthernet0
description Edzia
interface FastEthernet1
description dom
interface FastEthernet2
description Dziadek
interface FastEthernet3
interface Dot11Radio0
no ip address
no ip redirects
ip local-proxy-arp
ip nat inside
ip virtual-reassembly
no dot11 extension aironet
encryption vlan 1 mode ciphers tkip
encryption mode ciphers aes-ccm tkip
broadcast-key change 3600
ssid ciscowifi
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
world-mode dot11d country AU indoor
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1
description ciscowifi
encapsulation dot1Q 1 native
no cdp enable
interface Vlan1
no ip address
bridge-group 1
interface Dialer0
description Interfejs dzwoniacy
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp chap hostname [email protected]
ppp chap password 7 xxxxxxxxxxxxxxxxxxxxxx
interface BVI1
description Polaczenie dla sieci LAN
ip address 192.168.56.1 255.255.255.0
ip nat inside
ip virtual-reassembly
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
no ip http secure-server
ip nat inside source list 100 interface Dialer0 overload
ip nat inside source static tcp 192.168.56.10 80 interface Dialer0 80
ip nat inside source static tcp 192.168.56.10 22 interface Dialer0 22
logging trap debugging
logging 192.168.56.10
access-list 100 permit ip 192.168.56.0 0.0.0.255 any
access-list 100 deny ip any any
no cdp run
snmp-server community ciskacz RO
snmp-server chassis-id ciskacz
control-plane
bridge 1 protocol ieee
bridge 1 route ip
line con 0
no modem enable
line aux 0
line vty 0 4
exec-timeout 0 0
transport preferred ssh
transport input ssh
scheduler max-task-time 5000
end
please help - thanks!

Hello Marek,
I suppose you are not planning to do any kinds of advanced config using several VLANs and multiple SSIDs so let's just make your configuration simple and working.
In short, you need to remove all references to VLAN 1 and to any subinterfaces possibly related to the VLAN 1. This means in particular (follow these steps in sequence):
Remove the Dot11Radio0.1 subinterface entirely
In the Dot11Radio0 section, remove the encryption vlan 1 mode ciphers tkip command
In the dot11 ssid ciscowifi section, remove the vlan 1 command
After performing these steps, make sure that the ssid ciscowifi and encryption mode commands are still present in the Dot11Radio0 configuration, and if not, reenter them.
Best regards,
Peter

Dual Radio WGB and LWAPP Controller

Hallo everyone,
I have a wireless network managed by a 4402 controller with this sw version : 5.2.178.0
The client wants to add a stand alone wgb (cisco 1242 with an ios 12.4(21) ). The standalone ap associate to an LWAPP AP using the 5Ghz interface and propagate the same ssid at 2.4Ghz (I've also tried using a different ssid ). Actually the WGB is the only AP using that SSID at 2.4Ghz. As for the wired clients of the WGB I have no problems but if the client associate to the 2.4 Ghz SSID, I see it associated on the controller but no traffic from or to the client is allowed.
If for any case, the 5Ghz interface is resetted and the association betweeen the WGB and the controller is reformed, the 2.4Ghz client starts receiving and receiving traffic.
Any idea how to set things up from the the first association?
The wgb ssid is not set as infrastructure-client and the controller correclty identify it as a WGB client. In the same way the controller correclty see the 2.Ghz client like a wired client of the WGB but unless the association b.t.w the WGB and the controller is reset, no traffic reach the client.
I think that may be a problem related to how the IAPP protocol notify the presence of a client to WGB but I don't know how to work things out.. any idea?
Thank you in advance!

The 3600 series Access Points can have either internal or external antennae. You can tell by looking at the top of the AP. If there are 4 antenna connections (one in each corner) then they are external antennae.
If you cannot get to the AP to check them physically, the antenna type is also denoted by the part number.
AIR-CAP3602I-x-K9 has internal antennae
AIR-CAP3602E-x-K9 has external antennae
The 3600 does have dual radios built in, operating in the 2.4GHz and 5GHz frequency ranges. However, for them to show up as such, you have to enable both radios on the AP. You can do this either through the WebUI or the CLI.
The 802.11ac option is an external module that is attached to the underside of the 3600 AP. Please find the datasheet for the module here:
http://www.cisco.com/en/US/prod/collateral/modules/ps12859/ps13128/data_sheet_c78-727794.html
The 1552c Series access points are also dual-radio systems and should also have both radios turned on through the WebUI or CLI. Note the quote " The Cisco Aironet 1552C/1552CU Outdoor Mesh Access Points are dual-radio systems with DOCSIS 3.0/EuroDOCSIS 3.0 (8x4 HFC) compliant cable modem for power and backhaul." taken from the datasheet for these APs found here:
http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps11451/data_sheet_c78-641373.html
Cisco ships the APs with one Radio enabled and if you want the dual-radio functionality, you have to turn that on. Once that is done, you should see the APs show up correctly in the WLC 5508.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

How to create popup window with radio buttons and a input field

Hi Guys,
Can somebody give some directions to create a stand alone program to create a window popup with 2 radio button and an input field for getting text value. I need to update the text value in a custom table.
I will call this stand alone program from an user exit.
Please give me the guidance how go about it or please give any tutorial you have.
Thanks,
Mini

Hi,
There are multiple aspects of your requirements. So let's take them one at a time.
You can achieve it in the report program or you can use a combination of the both along.
You can create a standalone report program using the ABAP Editor (SE38). In the report program you can call the SAP Module pool program by CALL Screen <screen number>. And then in the module pool program you an create a subscreen and can handle the window popup with 2 radio button and an input field for getting the text.
For help - Module Pool programs you can search in ABAP Editor with DEMODYNPRO* and you will ge the entire demo code for all dialog related code.
For Report and other Module pool help you can have a look at the following:
http://help.sap.com/saphelp_nw70/helpdata/en/47/a1ff9b8d0c0986e10000000a42189c/frameset.htm
Hope this helps. Let me know if you need any more details.
Thanks,
Samantak.

Radio button and associated functionality is not working!

Hi Pros,
I am facing the following problem:
1.I have an interactive PDF created in Acrobat 9 Pro.
2.PDF have few radio buttons, each radio buttons ahave assigned valus(eg: 1,2,3 etc)
3.I have a text box in which the value of selected radio button is displayed.
4.PDF is working fine on my machine.
5.Client is having Internet Explorer version 7.0.5 and Adobe reader:8.2.6
6.The radio buttons and associated functionality is not working on client's machine.
7.The text box shows '0' even if we a radio button with value 2 or 1 is selected.
What will be the problem? How can I fix this issue?
Please help.

Thanks alot for helping me on this.
Thanks to u also ~graffiti

Radio Button and Check Box

I am looking for a way to implement a column domain as a radio button (e.g. Yes or No). So far I have only seen JHeadstart generate a list box. I cannot find any reference to radio buttons in the User Guide. Is it possible to generate a radio button?

Jan,
I looked into this post-gen action, but am not able to insert a radio group and buttons.
In a simple emp-dept application I am trying to create radio buttons in empTablePage.uix for the extra emp_class column I added to the emp table. The UIX components palette only gives me the option to insert a radio set. I can only get the option for radio group when I change the application structure to JSP.
BTW: Jdev 9.0.5.2

Radio button and group

Hi All,
Not quite follow what dev guide says about radio button and group implementation.
I tried but always got strange behavior.
I have a subtab with two radio buttons (rbt1 and rbt2)
rbt1 property defined as:
Initial Value: Y
Checked Value: Y
Unchecked Value: N
rbt2 property defined as:
Initial Value: Y
Checked Value: N
Unchecked Value: Y
Also, In my subtab PR, I init these two bts as a group:
OAMessageRadioButtonBean colButton1 =
(OAMessageRadioButtonBean)webBean.findChildRecursive("rbt1");
colButton1.setName("colGroup");
colButton1.setSelectedValue("Y");
OAMessageRadioButtonBean colButton2 =
(OAMessageRadioButtonBean)webBean.findChildRecursive("rbt2");
colButton2.setName("colGroup");
colButton2.setSelectedValue("N");
When the subtab render first time, rbt1 is checked and rbt2 is unchecked as expected. but when I go to other subtab then come back, the rbt1 is unchecked and rbt2 is checked (switch automatically).
The subtab PR is the only place I set this radio button value and group as showing above. Somewhere wrong with my logic or setting?
Regards,
KJ

Hi All,
Got issue resolved. When I was replying Ranjit previous post, I mentioned both of buttons bind to same VO attribute. Since the first rbt1 has defined checked and unchecked values (Y & N) and both of buttons are defined in same group, so I took off second rbt2 attribute binding then it works (won't switch automatically anymore).
I still defined init values for both of buttons and also removed setSelectedValue() method calls from PR.
Thanks again for the great helping.
KJ

I work at a radio station and my podcast got denied thru iTunes!

I work at a radio station and we do a live local band show every week. We wanted to have the previous episodes setup as podcasts but for some reason iTunes has denied our feed. We have permission from all the artists to use their music so not sure why there is an issue.
Feed is: http://rockthefox.podbean.com/feed/
I have a case number of 520580144 and my original case number of 294306745. We are now 4 weeks into our live show and yet the archived shows are still no where to be found on iTunes.
Please help...these Chicago local bands are waiting to be heard!
Thanks,
JP

There appears to be no technical problem with the feed, so it seems likely that the reason for rejection is that the Store staff suspect you of breaching copyright in the manner of countless other 'mix' podcasts.
I can only suggest emailing them at podcasts 'at' apple.com and explaining the situation.

Radio button and select option in one line

Hi,
I have an requirement in which i need to display the radio button and select option in one line in an report program.
How can i do it?
Regards,
Arun.

Hi,
Try this code.
TABLES: bkpf.
SELECTION-SCREEN BEGIN OF LINE.
PARAMETERS: p_r1 RADIOBUTTON GROUP a.
SELECTION-SCREEN COMMENT 4(20) text-001 FOR FIELD p_r1.
SELECTION-SCREEN COMMENT 30(12) text-002 FOR FIELD p_date.
SELECTION-SCREEN POSITION 39.
SELECT-OPTIONS: p_date FOR bkpf-budat OBLIGATORY.
SELECTION-SCREEN END OF LINE.
PARAMETERS: p_r2 RADIOBUTTON GROUP a.
text-001 = " Radio button"
text-002 = "Posting date"

Please help! How can I validate Radio Buttons and List Menu with PHP.

Hello everyone, I have been learning PHP step by step and
making little projects.
The point is I find it easy to learn by doing "practical
projects."
I have been reading the David Powers's Book on PHP Solutions
and it's really great, however there is nothing mentioned regarding
Validating Radio buttons. I know the book cannot cover every aspect
of PHP and maybe someone in here can help.
I have been learning how to process HTML forms with PHP.
The problem is every book or tutorial I have read or
encountered fall short on validation.
I'm wondering how I can learn to validate Radio Buttons and
Select List Menu.
I have managed to create validation for all other fields but
have no clue as to how I can get validation for Radio Buttons and
List Menu.
I would also like an error message echoed when the user does
not click a button or make a selection and try to submit the form.
I would appreciate any help.
Patrick

It's not that default value is "None." In fact it's not. It
will only be
"none" when the form is submitted.
Also if your submit button is names 'send' then
$_POST['send'] will only be
set if the form was submitted.
Make sure you didn't hit the refresh button on your browser
which usually
reposts the information. Also make sure you did not reach the
form from
another form with the same button names.
Otherwise paste the snippet.
Also you can check what fields are set in the post array by
adding this to
the top of (or anywhere on) your page:
print_r($_POST);
Cosmo
"Webethics" <[email protected]> wrote in
message
news:[email protected]...
>
quote:
Originally posted by:
Newsgroup User
> Off the top of my head this should be no different than
your radio buttons
> except that 'productSelection' will always fail the
!isset check when the
> form is submitted since the default value is "None", and
therefore always
> set. :-)
>
> So how about this..?
> <?php
> if (isset($_POST['send']) and
($_POST['productSelection'] == "None"))
> {echo "Please select a product.";}
> ?>
>
>
>
>
> "Webethics" <[email protected]> wrote
in message
> news:[email protected]...
> > Another question - how do i applied the code you
just showed me to
> > select
> > menu
> > or select list?
> >
> > This is the list:
> >
> > <div class="problemProduct">
> > <label for="productSelection"><span
class="product_label">Product
> > Name.</span></label>
> > <select name="productSelection" id="products"
class="selection">
> > <option value="None">-------------Select a
product----------</option>
> > <option value="Everex DVD Burner">Everex DVD
Burner</option>
> > <option value="Vidia DVD Burner">Vidia DVD
Burner</option>
> > <option value="Excerion Super Drive">Excerion
Super Drive</option>
> > <option value="Maxille Optical Multi
Burner">Maxille Optical Multi
> > Burner</option>
> > <option value="Pavilion HD Drives">Pavilion
HD Drives</option>
> > </select>
> > </div>
> >
> > I thought I could just change the name is the code
from operatingSystem
> > to
> > productSelection.
> >
> > Something like this:
> >
> > From this:
> >
> > <?php
> > if (isset($_POST[send]) and
!isset($_POST['operatingSystem']))
> > {echo "Please select an operating system.";}
> > ?>
> >
> > To this:
> >
> > <?php
> > if (isset($_POST[send]) and
!isset($_POST['productSelection']))
> > {echo "Please select an operating system.";}
> > ?>
> >
> > But this does not work, any ideas?
> >
> > Patrick
> >
>
>
>
>
> Hey, I tried this about but as you mentioned, since the
default product
> value
> is "None" an error message appears when the page loads.
>
> Is there a way to code this things so that even though
the default value
> is
> "None" there ia no error message untle you hit the
submit?
>
> When I applied the code, it messes up the previous code,
now the operating
> system is requiring an entry on page load.
>
> When I remove the code from the list menu everything
goes back to normal.
>
> I know this is a little much but I have no other
alternatives.
>
> Patrick
>

Radio Buttons and Event Structures

Guys, I am hoping for some help here on something I probably should know but cant figure out how to do. I am using a set of radio buttons and an event structure to run a UI. The radio buttons are acting as both a user input and indicator of current status selected by the user. I have the event structure set to run on value change of the radio button. All works great unless the operator decides that he wants to repeat the selection that the radio button is already set to. The event structure does not recognize this as a change of value and will not execute. Is there a way to set the event structure up to run even if the same selection of the radio button is made a second time? I attached a crude example to this post. Basically everytime I press the button, I want an entry made into the text box, regardless if the selected item was already pressed. Any thoughts.
Troy
Attachments:
Radio Button Test.vi ‏16 KB

Instead of hacking around the inherent nature of radio buttons, why not just use a Cluster? Its behavior in the UI is more customizable. Check this out:
I just replaced your radio buttons with a cluster, and added a little logic to the event structure to get it to behave the way you describe. I've attached the VI below, saved in 8.2, if you want to try it out.
Hope this helps,
-D
Message Edited by Darren on 11-07-2006 10:45 AM
Darren Nattinger, CLA
LabVIEW Artisan and Nugget Penman
Attachments:
cluster_buttons.png ‏7 KB
Cluster Test.vi ‏17 KB

Radio buttons and SQL

Hi,
I have a column in my database called buy_or_share. I have
the type set at ENUM ('buy', 'share') and default as: buy. I am
building a search page for users to search whether they want to buy
or share (in the form of a radio group) and then a search bar for
the user to type into freely what product, category, or store name
they are seeking.
I have tried to attach dynamic radio feature to the buttons
and I've also tried quite a few different ideas with the recordset,
but nothing has worked. When I search for a product, I am given
results of the product for both buy and share so obviously the
radio group isn't separating the results to either buy or share.
The trouble is that I don't know what I'm doing wrong, is it
something with the radio group? the recordset? the dynamic form
elements? my php code, should I have a conditional statement
surrounding the buttons so that if 'buy' is true then retrieve the
database for 'buy' else 'share' true then get that information,
else neither are true display 'no results'?... Thank you for the
help!
I have attached the relevant code...
Brad

Hi,
One way to achieve this would be to
Create an Item 'Radiogroup (with Submit)' called PXX_RADIO and enter 'STATIC:SQL 1;1,SQL 2;2,SQL 3;3' in the List of values definition
Create a region of type 'SQL Query (PL/SQL function body returning SQL query) and enter
begin
IF :PXX_RADIO = 1
THEN
return 'Select 1 from dual;';
ELSIF :PXX_RADIO = 2
THEN
return 'Select 2,2 from dual;';
ELSIF :PXX_RADIO = 3
THEN
return 'Select 3,3,3 from dual;';
end if;
end;
Set the region to use 'Use Generic Column Names (parse query at runtime only)
In the regions conditional display set condition type to 'Value of Item in Expression 1 is NOT NULL' and enter PXX_RADIO in Expression 1
So depending on the value of the radiogroup the relevant SQL is executed.
Hope this helps
Regards
Paul

How can i get Radio buttons and parameters in a Single Straight Line

Hi Experts,
How can i get Radio buttons and parameters in a Single Straight Line...
Example:
   r1 r2 p1 p2.....
Cheers,
Priya
Points granted.

Write the following code for the selection screen:
DECLARATION OF PARAMETERS.
SELECTION-SCREEN: BEGIN OF BLOCK select WITH FRAME TITLE text-001,
                  BEGIN OF LINE.
                  SELECTION-SCREEN COMMENT 1(10) FOR FIELD p_detail.
                  PARAMETERS p_detail RADIOBUTTON GROUP r1 DEFAULT 'X'.
                  SELECTION-SCREEN COMMENT 25(10) FOR FIELD p_summry.
                  PARAMETERS p_summry RADIOBUTTON GROUP r1.
SELECTION-SCREEN: END OF LINE,
                  END OF BLOCK select.
this will solve your poblem surly. reward the points if you find helpful
Regards,
Siddarth

Can I run a Unique Clients and Users Summary report customized by both floor area and SSID?

In Cisco Prime, can I run a Unique Clients and Users Summary report customized by both floor area and SSID?

Allright guys. I appreciate the quick responses. I've worked a lot in CR however i am not understanding the solution so I'd appreciate if you can dumb it down for me. If i understand it correctly you guys are suggesting to make a formula, that either return my group by string (which is a formula in my report) or the Quantity. I tried writing a formula like this
if ({@param} = 1 then
GroupName ({@GroupBy})
else
{NetPNL.GrossAfterAdj}
but it seems like CR does not allow you to return 2 different data types. Even if it had worked i would not know what to do from there. Can anyone please dumb it down for me. To make my situation more clear below is an example of how my data is..
MN 100
MN 200
MN 50
CA 300
CA 500
when the data shows in the report, its grouped by state, so it comes out like
MN 350
CA 800
I want the users to decide whether they want it sorted by state (ascending)
CA 800
MN 350
or Total quantity (asc)
MN 350
CA 800

Radio subinterfaces and # SSID

Similar Messages

Maybe you are looking for