Refresh temporary interface used in lookup

I am using temporary interface to provide a datastore for lookup.
temporary interface uses database schema for storage.
How do I refresh lookup data? I can see that the interface that uses lookup just reference to table.
Do I need to execute my temporary interface manually (or just before the main interface) to make sure my lookup is up-to-date?

Can I use In Memory Engine to store results from temporary/yellow interface?

Similar Messages

ASA9.1 how to use route-lookup instead of "NAT-lookup" for egress interface on non-identity NAT

Hi,
I have an ASA firewall with three interfaces, inside, outside and Link.
I have a situation where I need the ASA to perform the following nat rules:
from "Inside" to "Link" - any source to destination 192.168.51.0/24 - translate source to 10.0.0.19
from "inside" to "outside" - any source to any destination - translate source to "interface" (internet navigation)
from "inside" to "outside" any source to 192.168.51.0/24 - translete source to 10.0.0.17
This is what I am trying to get working:
nat (any,TEF) source dynamic any 130.130.0.19_nat destination static obj_192.168.51.0 obj_192.168.51.0
nat (any,outside) source dynamic any 130.130.0.17_nat destination static obj_192.168.51.0 obj_192.168.51.0
The problem is that the "outside" route to 192.168.51.0 is an alternative route over a VPN tunnel. I'm using sla monitor, so when the "Link" interface is out, the route table changes the network 192.168.51.0/24 to be reachable over the outside interface. but ASA is using the NAT rule to perform "egress interface lookup" instead of route-lookup.
I know about the command route-lookup on the NAT configuration, but I need to translate the source address and when I try to use the route-lookup command I get an error message:
ERROR: Option route-lookup is only allowed for static identity case
Anybody has some suggestion?
Thanks

Hi Julio,
Thank you for the reply.
It didn't work either.
Here are the options I get when I use the specific interfaces (using "source dynamic"):
configure mode commands/options:
description Specify NAT rule description
inactive Disable a NAT rule
net-to-net Net to net mapping of IPv4 to IPv6
service NAT service parameters
If I try to use source static:
nat (inside,TEF) source static inside_nat 130.130.0.19_nat destination static obj_192.168.51.0 obj_192.168.51.0 route-lookup
ERROR: Option route-lookup is only allowed for static identity case

How to use two lookup in single interface in ODI 11g

Hi All,
I am trying to load GL_CODE_COMBINATIONS CC + FND_FLEX_VALUES_VL FF to target table W_GL_CODE_COMBINATIONS.
I duplicated FND_FLEX_VALUES_VL as FND_FLEX_VALUES_VL1 FF1 for my join condition.
In target table I have included 2 new columns named SEGMENT2_DESC and SEGMENT3_DESC.
In my interface i am using FND_FLEX_VALUES_VL as lookup and join condition is CC.SEGMENT2=FF.FLEX_VALUE
Mapping expression of target column SEGMENT2_DESC is FF.DESCRIPTION.
In my interface i am using FND_FLEX_VALUES_VL1 as lookup and join condition is CC.SEGMENT3=FF1.FLEX_VALUE
Mapping expression of target column SEGMENT3_DESC is FF1.DESCRIPTION.
Execution of this interface taking more time. When using single lookup and SEGMENT2_DESC data loading is fast.
Kindly advice me regarding this.
Thanks in advance.

Are the number of records in lookup very large ?
Why cant you use the same lookup once and have the join containing both the conditions.
YOu dont have to use lookup at all. YOu can also drag the "so called" lookup table in the source and build the join conditions yourself.
The join condition would be
CC.SEGMENT2=FF.FLEX_VALUE and CC.SEGMENT3=FF.FLEX_VALUE

How to use temporary interface in another interface as derived table in 10g

Hi ,
Can somebody please tell me how to use temporary interface in another interface as derived table in 10g.
I have an option in odi 11g to this task.But i am working on odi 10g for my project.So that please help me to do this task.
I can able to create temporary interface in 10g ,but i dont know how to use that temporary interface in another inerface as derived table.
Thanks in Advance
Thanks,
Srikanth A

A temp interface CANNOT be used as a derived table in ODI 10g.
All you can do is to drag and drop the temp interface as the source in the mapping.
PS. Please remember to assign correct/helpful points to the people who help you in the forum.

Is a database table required for temporary interfaces with flat file data set source ?

Folks, this is the situation I have in ODI 11.1.1.7
I have a temporary interface (yellow), called MJ_TEMP_INT, that pulls data from TWO data sets in the source into a temporary target (TEMP_TARG). The catch is one data set pulls from a from a table whereas the other data set pulls from a flat file. A union is done on the data sets.
I then create another interface, called MJ_INT, that uses the MJ_TEMP_INT as a source and the target is a real db. table called "REAL_TARGET"
Two questions:
When I execute my second interface (MJ_INT), I get a message "ORA-00942: table or view does not exist" because it is looking for a real db table TEMP_TARG. Why must I have one ? because I am pulling from a flat file ?
On my second interface (MJ_INT) when I look at the property sheet of my source interface MJ_TEMP_INT (yellow), the checkbox next to "Use temporary interface as Derived table" is DISABLED. Why ? Is is also because my temporary interface is pulling from a flat file ?
I have attached a file that shows a screen shot of my ODI studio.
By the way, IF my temporary interface source has only one data set pulling from a db. table into a temporary target table, say called MJ_TEMP2_TARG, and then when I use this temporary interface as a source to another other real db. target table (REAL2_TARGET), THEN, every thing works. ODI does not require me to have a real db. table MJ_TEMP2_TARG and the checkbox for "Use temporary interface as Derived table" is NOT DISABLED and my REAL2_TARGET table gets populated.
Thank you in advance.
M. Jamal.

Thanks SH. I thought so.
Though I understand the reason to materialize the file in a staging area, but that almost defeats the purpose of having a temporary interface in this case if we have to save the data in a permanent db. table first. I assume the db. table sticks around and is not automatically dropped once the interface executing ends. If the db. table sticks around then I also must truncate it first before executing the temporary interface each time. Right ?

Problem reopening and/or refreshing PDF files using Acrobat Reader V. 8.0

I upgraded to Adobe Acrobat Reader V. 8.0 and have encountered problems refreshing PDF files in the Safari 2.0.4 browser when I am logged into the secure area for Value Line Publishing. Some of the PDF Files in this area can be opened and/or refreshed multiple times. Other PDF files in this area allow me to open them once. I cannot reopen those previously viewed files (or refresh the screen) -- after refreshing, the window changes to a blank white screen, and the files do not reopen.
I am perplexed because I do not have difficulty refreshing the PDF files (within Safari) using the native PDF viewer, I did not have problems refreshing files using Acrobat Reader V. 7.0 and I do not appear to have problems refreshing PDF files using Acrobat Reader V. 8.0 when I am outside the secure area or on other web sites.
I have replaced the Acrobat Reader plug-in, manually removed all remnants of previous versions of Acrobat Reader and reinstalled V. 8.0. and I also upgraded from Mac OS 10.4.8 to 10.4 9, all to no avail.
I can clear the Safari cache files as a temporary solution, but I encounter the same difficulties with the “problematic” files once they have been opened again.
I can also download the PDF files to my hard drive and refresh them multiple times within Safari and also using Acrobat Reader V. 8.0
The software personnel at Value Line Publishing have investigated their system and have referred me back to Apple. Has anyone heard of similar problems associated with Adobe Acrobat Reader V. 8.0 used in conjunction with Safari 2.0.4?
PowerBook G4 Mac OS X (10.3.9)

Hi Rodney
Welcome to Apple Discussions
This sounds like one of those "oddities", contributed to by a few sources.
I can clear the Safari cache files as a temporary solution, but I encounter the same difficulties with the “problematic” files once they have been opened again.
Wondering if you disabled the Safari Cache would the refresh function work correctly? As a test you can disable the Safari Cache by Emptying the Cache first via the Safari menu, then Quit Safari. Now go to the Finder>Your User Library>Caches>Safari. Single click on the Safari folder, then Apple Key + I to open Info panel. There, check the "locked" box. This prevents further additions to the cache. The downside, you lose your ability to upload images etc. within Safari (my cache is disabled, so I use Firefox for the uploads).
Then restart Safari. Try the PDF from within Safari.
Post back

Using a lookup for mapping program to retrieve the specific value

Hi All,
I have a scenario like I need to use a lookup for mapping program to retrieve the specific value based on the input parameters.
Here I have got some rough idea like
1. Creation of java program to connect the DB table and access the values, Import this java program as archive into XI.
2. Creation of user defined function to use the above java program
3. Include the user defined function in the interface mapping.
Here I feel it needs some more info to complete this scenario, so can anyone provide the step by step procedure for the above scenario.
Thanks in advance.
Vijay.

Hi Vijay,
Basically you have embed Database lookup code in the UDF. For all kind of Lookups refer to below links..
Lookup - /people/alessandro.guarneri/blog/2006/03/27/sap-xi-lookup-api-the-killer
DB lookup - /people/siva.maranani/blog/2005/08/23/lookup146s-in-xi-made-simpler
SOAP Lookup - /people/bhavesh.kantilal/blog/2006/11/20/webservice-calls-from-a-user-defined-function
http://help.sap.com/saphelp_nw04/helpdata/en/cf/406642ea59c753e10000000a1550b0
Lookups in XI made simpler - /people/siva.maranani/blog/2005/08/23/lookup146s-in-xi-made-simpler
How to check JDBC SQL Query Syntax and verify the query results inside a User Defined Function of the Lookup API -
http://help.sap.com/saphelp_nw04/helpdata/en/2e/96fd3f2d14e869e10000000a155106/content.htm
/people/prasad.illapani/blog/2006/10/25/how-to-check-jdbc-sql-query-syntax-and-verify-the-query-results-inside-a-user-defined-function-of-the-lookup-api
Lookups - /people/morten.wittrock/blog/2006/03/30/wrapping-your-mapping-lookup-api-code-in-easy-to-use-java-classes
Lookups - /people/alessandro.guarneri/blog/2006/03/27/sap-xi-lookup-api-the-killer
/people/siva.maranani/blog/2005/08/23/lookup146s-in-xi-made-simpler
http://help.sap.com/saphelp_nw04/helpdata/en/cf/406642ea59c753e10000000a1550b0/content.htm
/people/sap.user72/blog/2005/12/06/optimizing-lookups-in-xi
Lookups with XSLT - https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/8e7daa90-0201-0010-9499-cd347ffbbf72
/people/sravya.talanki2/blog
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/05a3d62e-0a01-0010-14bc-adc8efd4ee14
How we have to create the lookups?
Check this weblogs with some screenshots on how to achieve this:
/people/siva.maranani/blog/2005/08/23/lookup146s-in-xi-made-simpler
/people/sravya.talanki2/blog/2005/12/21/use-this-crazy-piece-for-any-rfc-mapping-lookups
/people/alessandro.guarneri/blog/2006/03/27/sap-xi-lookup-api-the-killer
/people/sap.user72/blog/2005/12/06/optimizing-lookups-in-xi
/people/morten.wittrock/blog/2006/03/30/wrapping-your-mapping-lookup-api-code-in-easy-to-use-java-classes
Ranjeet Singh.

Adding UNION Dataset on EXISTING INTERFACE using SDK

hi
i am facing issue while adding UNION dataset and Mappings on Existing interface using ODI SDK.
if anyone done before, please tell me how to do it.
i am getting Unique constraint error.
thanks
nidhi

Hi Michael Rainey, Unique constraint error was solved, but i am getting some other issue, here is the detail.
i am trying to a add new Dataset(for Union Operation) using ODI SDK on existing Interface.
Scenario:
Dataset1 :
Source DataStore : W_PLM_LISTENTRY_PS
Column Name : ENTRYVALUE , ENTRY_ID
Filter : id=1000
Dataset 2:
Source DataStore : W_PLM_LISTENTRY_PS
Column Name : ENTRYVALUE, ENTRY_ID
Filter : id=2000
Target DataStore(Temporary):
Coloumns : Name , ENTRY_ID
Mapping between DataSet1 and Target Data Store already done in the Interface.
Now I have to add new DataSet as “Dataset2” with UNION Operator and do the mapping in to the same interface through ODI SDK.
Issue:
I have give the ODI SDK code for the below, while running that I am getting following error
Exception in thread "main" java.lang.IllegalArgumentException: Object must not be null
while debugging I found that error occur exactly when the following code was running.
interactiveHelper.performAction(new InterfaceActionOnTargetMappingSetSql("NAME","W_PLM_LISTENTRY_PS.ENTRYVALUE",newDataSet));
Already mentioned that I am using Temporary Target datastore, so changed the target column name as "ENTRYVALUE" instead of “NAME” and modified java code like
interactiveHelper.performAction(new InterfaceActionOnTargetMappingSetSql("ENTRYVALUE","W_PLM_LISTENTRY_PS.ENTRYVALUE",newDataSet));
after this change it working well.
So, it seems when ever target datastore column name not equal to source data store column name I am getting this error.
Is it a bug? or am I doing anything wrong? please let me know.
Thanks
nidhi
Code:
OdiInstance odiInstance = odiInstanceHandle.getOdiInstance();
ITransactionStatus trans = odiInstance.getTransactionManager().getTransaction(new DefaultTransactionDefinition());
String prdLineSQSILDimInterface="SIL_PLM_InternalOraganizationDimension.W_PLM_INT_ORGANIZATION_D_SQ_INT_ORG";
String sourceDataStore="W_PLM_LISTENTRY_PS";
Collection<OdiInterface> odiInterfaces = ((IOdiInterfaceFinder)odiInstanceHandle.getOdiInstance().getTransactionalEntityManager().getFinder(OdiInterface.class)).findByName(prdLineSQSILDimInterface, "BIAPPS");
OdiInterface interface=null;
for (Iterator iter = odiInterfaces.iterator() ; iter.hasNext() ; )
interface = (OdiInterface)iter.next();
OdiDataStore odiDataStore = ((IOdiDataStoreFinder) odiInstanceHandle.getOdiInstance().getTransactionalEntityManager().getFinder(OdiDataStore.class)).findByName(sourceDataStore, "BIAPPS");
InteractiveInterfaceHelperWithActions interactiveHelper = new InteractiveInterfaceHelperWithActions(interface, odiInstanceHandle.getOdiInstance(), odiInstanceHandle.getOdiInstance().getTransactionalEntityManager());
DataSet newDataSet=new DataSet(interface,"MySet");
newDataSet.setOperator("UNION");
newDataSet.setOrder(10);
interactiveHelper.performAction(new InterfaceActionAddSourceDataStore(odiDataStore, newDataSet,new AliasComputerDoubleChecker(),new ClauseImporterLazy(),new AutoMappingComputerLazy()));
interactiveHelper.performAction(new InterfaceActionOnTargetMappingSetSql("ENTRY_ID","W_PLM_LISTENTRY_PS.ENTRY_ID",newDataSet));
interactiveHelper.performAction(new InterfaceActionOnTargetMappingSetSql("NAME","W_PLM_LISTENTRY_PS.ENTRYVALUE",newDataSet));
odiInstance.getTransactionalEntityManager().persist(anInterface);
odiInstance.getTransactionManager().commit(trans);
Edited by: knidhi on Apr 18, 2013 2:40 PM
Edited by: knidhi on Apr 18, 2013 2:48 PM
Edited by: knidhi on Apr 18, 2013 2:48 PM
Edited by: knidhi on Apr 18, 2013 2:51 PM
Edited by: knidhi on Apr 18, 2013 2:54 PM

Custom Interface using Entity Objects

Right now, we can only define cutom interfaces using the Generic Loader. I was wondering if this functionality is going to be extended so that users can define custom interfaces using EOs instead of lct files.

Hi Mugunthan,
I have the exact same requirement, to know a little bit more BC4J Support, since we want to use iSetup to control the load of our Receivables Custom Database Tables also. I have opened an SR and they have forwarded to the Receivables Team, which i do not believe will help us, since our need is to know technically the iSetup Custom Interface process for BC4J. Can you point me out some documentation on this? my e-mail contact is [email protected]
Regards
Thiago

How to use JDBC Lookup in PI 7.1 ?

Hi,
Please advise how to use JDBC lookup in message mapping PI 7.1 ? any reference link / document ?
I have followed this step below :
1. Create the external definition for the database table.
2. Use the external definition (table) in message mapping JDBC Lookup.
But the target still "Yellow colour" meanint the mapping hasnot completed yet ? why ? and when i double click the JDBC lookup
there some error message
"No suitable parameter found; define new parameter of type 'Channel' first"
Please advise.
Thank You and Best Regards
Fernand

Hi Fernand,
JDBC Lookup can be done in PI 7.1 using below mentioned steps :
1) Create a communication channel between PI and the database to connect to database.
2) Import the table data as External Definition.
3) In message mapping where this lookup is to be used select JDBC Lookup under Conversions and map
4) Double Click on JDBC Lookup
5) Select parameter and a database table (imported as the external definition). All the elements of the table will appear in the middle column. Select and move the input parameters to the left side column and the output parameters to the right side column. Click OK.
6) Under message mapping go to signature tab and define the parameter as channel and category as JDBC Adapter Type.
7) Under Operation mapping define the parameter & associate it with parameter defined in Message Mapping.
Thanks
Amit

Getting error while running the Interface using AGENT

Hi All,
i am not able to run the interface using Agent service which running in the another machine, while running i am getting error message like
java.lang.Exception: Error during Session launching
     at com.sunopsis.dwg.dbobj.SnpSession.remoteExecute(SnpSession.java)
     at com.sunopsis.graphical.l.or.e(or.java)
     at com.sunopsis.graphical.r.z.actionPerformed(z.java)
     at javax.swing.AbstractButton.fireActionPerformed(Unknown Source)
     at javax.swing.AbstractButton$ForwardActionEvents.actionPerformed(Unknown Source)
     at javax.swing.DefaultButtonModel.fireActionPerformed(Unknown Source)
     at javax.swing.DefaultButtonModel.setPressed(Unknown Source)
i ran the Agent services in Comment prompt, there i am getting the error like follows
java.lang.NullPointerException
at com.sunopsis.dwg.cmd.DwgCommandSession.treatCommand(DwgCommandSession.java)
at com.sunopsis.dwg.cmd.DwgCommandBase.prepare(DwgCommandBase.java)
at com.sunopsis.dwg.cmd.e.t(e.java)
at com.sunopsis.dwg.cmd.h.y(h.java)
at com.sunopsis.dwg.cmd.e.run(e.java)
at java.lang.Thread.run(Unknown Source)
here i have mentioned the steps which i followed for creating agent service.
i have two machine namely A and B both having the ODI
i am going to use the B machine as a centralized server. so i edited the odiparams.bat file in B machine in ODI locaiton and filled the repository information
from A machine i opened the Topology and created the Agent service there i mentioned the HOST name as "B" and port number 20300. and i configure the logical agent aswell
from B machine i started the Agent service like agentscheduler "-port=20300".
Agent service launched seccessfully.
From A machine i tested the Agent. that also shown the successful window message.
then i started running the interface using the agent i am getting the error which i have mention in the beginging.
Interface which i ran will do the text file to table loading, so i kept that file in particular location in B machine( i have configure this location when i created the file data store in topology in A machine).
Please help me to solve the problem...
thanks
nidhi
Edited by: knidhi on Nov 26, 2009 6:54 PM

Thanks For your Reply,
I ran the agent as you said. here is my observation
from the Machine B where agent is actually running, i could able to run the interface using agent service.
but from the machine A while running the interface i am getting the following error message
java.lang.Exception: Error during Session launching : Error during Session Preparation : You are trying to execute a session with an agent that is undefined in your repository. Please check the agent -NAME parameter.
     at com.sunopsis.dwg.dbobj.SnpSession.remoteExecute(SnpSession.java)
     at com.sunopsis.graphical.l.or.e(or.java)
     at com.sunopsis.graphical.r.z.actionPerformed(z.java)
     at javax.swing.AbstractButton.fireActionPerformed(Unknown Source)
     at javax.swing.AbstractButton$ForwardActionEvents.actionPerformed(Unknown Source)
     at javax.swing.DefaultButtonModel.fireActionPerformed(Unknown Source)
     at javax.swing.DefaultButtonModel.setPressed(Unknown Source)
     at javax.swing.AbstractButton.doClick(Unknown Source)
     at javax.swing.plaf.basic.BasicMenuItemUI.doClick(Unknown Source)
     at javax.swing.plaf.basic.BasicMenuItemUI$MouseInputHandler.mouseReleased(Unknown Source)
     at java.awt.Component.processMouseEvent(Unknown Source)
     at java.awt.Component.processEvent(Unknown Source)
     at java.awt.Container.processEvent(Unknown Source)
     at java.awt.Component.dispatchEventImpl(Unknown Source)
     at java.awt.Container.dispatchEventImpl(Unknown Source)
     at java.awt.Component.dispatchEvent(Unknown Source)
     at java.awt.LightweightDispatcher.retargetMouseEvent(Unknown Source)
     at java.awt.LightweightDispatcher.processMouseEvent(Unknown Source)
     at java.awt.LightweightDispatcher.dispatchEvent(Unknown Source)
     at java.awt.Container.dispatchEventImpl(Unknown Source)
     at java.awt.Window.dispatchEventImpl(Unknown Source)
     at java.awt.Component.dispatchEvent(Unknown Source)
     at java.awt.EventQueue.dispatchEvent(Unknown Source)
     at java.awt.EventDispatchThread.pumpOneEventForHierarchy(Unknown Source)
     at java.awt.EventDispatchThread.pumpEventsForHierarchy(Unknown Source)
     at java.awt.EventDispatchThread.pumpEvents(Unknown Source)
     at java.awt.EventDispatchThread.pumpEvents(Unknown Source)
     at java.awt.EventDispatchThread.run(Unknown Source)
i have created both physical and logical agent with the same name "DEMO_AGENT", and i ran the agent in the Machine B like
agentscheduler "-port=20301" "-name=DEMO_AGENT"
Please help me to solvethe issue...
Thanks
Nidhi
Edited by: knidhi on Nov 27, 2009 11:04 AM
Edited by: knidhi on Nov 27, 2009 11:04 AM
Edited by: knidhi on Nov 27, 2009 11:05 AM

Error while refreshing BO objects using live office

Hi Forum,
We are getting below error while refreshing the data using Live Office plug-in on PPT.
“An error occurred while receiving the HTTP response to http://........ This could be due to the service endpoint binding not using the HTTP protocol. This could also be due to an HTTP request context being aborted by the server.”
This error comes in exact 5 minutes.
The server name used for web service is from a clustered environment. When the individual node is used Live office refresh works fine but while using the generic name refresh fails.
Please provide your inputs.

Hi Honed,
Take the backup of dsws.properties file and do the following changes:
properties            values
domain               @<clustername>
session.timeout    value higher than 5 minutes
Below pdf can help you further:
http://help.sap.com/businessobject/product_guides/boexir4/en/xi4_wssdk_admin_en.pdf
Regards,
Yuvraj

How to find out what are the interfaces used for Job and Job Codes

HI All,
I just wanted to know how do we find out what are the interfaces used for Job and Job codes .
Thanks In Advance
Sunny

Hi,
Here is an idea for your request.
Basically you can create a simple query on multiprovider 0TCT_MC01.
Filter: you can use a variable for restriction of time ( calday, or calmonth) since you should be interested for a time period.
Choose following characters into your objects:
InfoProvider ( 0TCTIFPROV ) - you can create a variable for choosing infoprovider before query runs.
*Tp.[Type of BI Application Object] 0TCTBISOTYP = filter this with 'QUERY' or whatever your need is.
*BI Application Object 0TCTBISBOBJ, ( this will give you the name of the queries)
In key figures choose, Count for BI Appl. (0TCTWTCOUNT).
(number for query run)
Create a condition , for top 20.
Hope this helps.
Derya

Use of Lookup Files in BI Applications

Hi,
Can any one tell the use of lookup files in BI Applications. While doing the configurations (for all modules) for these lookup files we get the data from the ERP database tables using the query provided by oracle and populate the file and then map with some domain values.
Why cant we directly populate the datawarehouse tables using the ERP tables instead of populating through the lookup files (which we any how populate with ERP tables). Also what is the use of domain values. Does these use in reporting puposes and anlyzing the data or business.
Thank You,

For e.g, when you map the GL group account numbers, the predefined group codes such as 'CASH', 'AR', 'AP' , 'TAX' etc are the domain values. In the repository, the metrics are defined based on these domain values.
Say, you mapped your CASH accounts from 0011 through 0100, then OBIEE calculates the metrics related to CASH as summation (or some kind of calculation) on the accounts that have the group codes (domain values) as CASH.
It should be possible to update the domain values directly from ERP database tables but the ETL expects the mapping to be in files. Also in some cases we cannot change the default domain values, all we can change is the mapping to these domain values or create new domain values. At one client, we had to create a new account group code called 'FIXED ASSET' as the default domain values were not sufficient but then we had to change the repository to include new metrics and change existing ones to incorporate this new group code.
-Nilesh
http://www.appsbi.com

What is the use of lookup tranformation in odi

Hi Experts,
What is the use of lookup transformation in ODI.
In ODI we use different kinds of joins, so my doubt is what is the difference between lookup transformation joins and normal joins we use in ODI.
Please let me know with your valueable information.
Thx,
Sahadeva.

Use the SIM card to connect to the cell carrier 3G network when there is no wifi available.
To set it up, see this -> http://support.apple.com/kb/HT4157

Refresh temporary interface used in lookup

Similar Messages

Maybe you are looking for