Regarding ICMP "Packet Too Big" message in 6PE RFC 4798
Dear All,
The penultimate para in Section 3, Page 6 of 6PE RFC 4798 states the following:
"Otherwise, routers in the IPv4 MPLS network have the option to generate an ICMP "Packet Too Big" message using mechanisms as described in Section 2.3.2 .... of [RFC3032]"
As per RFC3032, the routers in the IPv4 MPLS network can generate ICMP "Time Exceeded" message or "Destination Unreachable because fragmentation needed and DF set" message.
Can someone please explain, how a IPv4 MPLS router will generate an ICMP "Packet Too Big"? This requires that the router in IPv4 MPLS network be a dual stack router to understand the IPv6 header under the label stack. Is my understanding correct?
If the router is an intermediate LSR, how will it know the path to the IPv6 destination even if it is dual stack router?
Thanks in advance.
Cheers,
Sriram
Sriram,
The IPv4 core router does need to have code to understand IPv6 and create the "Packet too big" message and so on. It does not need to be configured for IPv6 though (dual stack).
The forwarding will be done based on the incoming label stack for that IPv6 packet, which means that the ICMPv6 message will be constructed with the source of the original packet as the destination IPv6 address, the top label for the incoming IPv6 packet will be swapped, prepended to the ICMPv6 message and forwarded through the egress interface. The egress PE will received this ICMPv6 message and forwarding appropriately.
The same mechanism is used when performing traceroutes in an L3VPN context, as the core routers have no knowledge of the address space being used by the L3VPN customers and couldn't otherwise forward ICMP messages to the proper source.
Regards
Similar Messages
-
Exporting a sequence and getting an Error file too big message
I have tried to export a sequence using Quicktime conversion. It is a two minute clip and I keep getting an "Error, File too big" message. Does anyone know what can be happening?
What exactly are you exporting to? Settings, codec, data rate? What drive are you exporting to? How is it formatted?
-
Disk image of HD -- "image/device too big"
I'm trying to make a disk image of my hard drive as a backup. I did this with the other three Macs in my house, using Disk Utility and saving them to an external Firewire drive. No problem. But when I try to do the same thing with my G5, I get a message saying "image/device is too big." If I was getting this message from my wife, I guess I'd be flattered ... from my Mac, not so much.
The thing is, I should have plenty of room. The external drive has 139 GB of space available and the G5 is only using 51GB. Get Info says I have 148 GB capactiy and about 97 GB available. Does the external drive need room for the whole 148 GB to create the disk?
The main difference between the other operations and the troublesome one is that I save the other Disk Images using my G5 running MacOS 10.4.11. The other Macs all were running 10.3.9. I'd access them in Target Mode on my G5 and save the Disk Image. When I tried to reverse the process and used the newest 10.3.9 machine (a G4) to save a dmg of my G5, I get the "too big" message.
Any suggestions? Would Carbon Copy Cloner (or something else) allow me to do this from the G5? Any help would be appreciated.Found answer elsewhere.
-
A Protocal Message was rejected because it was too big
Hi,
We are having SAP BOBJ 4.1 support pack 2 and patch 3, on linux environment,
when we run some specific reports we are facing any issue
A protocol message was rejected because it was too big (more than 100663296 bytes). To increase the limit (or to disable these warnings), see CodedInputStream::SetTotalBytesLimit() in google/protobuf/io/coded_stream.h.
we have increased the value of
List of Values Batch size = 4000
Maximum list of Valuses Size = 100000
Still we are facing the same issue.
Please let me know what could be the issue as other reports are working fine.
Thanks,
Balaji.SHi Balaji,
Yes, However at times issues do appear due to "ulimit" settings.
Also this error comes from maximum size of protobuf packets, which are exchanged
between WIPS and DSLBridge service.
It seems that data being retrieved might have increased.
Tune the BICSResultChunkSize value to an appropriate one.
******Please take a backup of registry before doing the cahnges.
1. Open the Windows Registry
a. Click Start > Run. The Run dialog box appears
b. Type #regedit# in the Open: text box. Click OK. The Registry Editor appears
c. navigate to the key [HKEY_LOCAL_MACHINE\SOFTWARE\SAP BusinessObjects\Suite XI 4.0\default\WebIntelligence\Calculator]
2. right click, select New > String Value and name it BICSResultChunkSize and value (e.g. 4000) lower than default 100000 lines
3. close the Windows Registry
4. Restart the Web Intelligence Processing Server and the Adaptive Processing Servers that host the DSL Bridge Service
Regards,
Nachiket -
Reports getting error message that they are too big
Hi
When modifying a standard report and adding dimensions keep getting warning message indicating that the report is too big.
Is there a limit to the number of lines?
Regards
NeelHi Neel,
Administrators set a SPM UI property that will warn business user when the report they are trying to execute exceeds specified number or cells. This cell limit will depend on how your JAVA server is sized. Also SPM being an analytical application setting this too high may cause performance issue. Use the following menu path to get to this property
Administration -> Analysis Administration -> Application properties -> General tab -> Cell limit for Large Reports
Rohit -
I'm trying to open a 900kb Word doc (240pages) in Pages but get this error message: Import Warning - A table was too big. Only the first 40 columns and 1,000 rows were imported.
Julian,
Pages simply won't support a table with that many rows. If you need that many, you must use another application.
Perhaps the originator could use a tabbed list rather than a table. That's the only way you will be able to contain a list that long in Pages. You can do the conversion yourself if you open the Word document in LibreOffice, Copy the Table, Paste the Table into Numbers, Export the Numbers doc to CSV, and import to Pages. In Pages Find and Replace the Commas with Tabs.
There are probably other ways, but that's what comes to mind here.
Jerry -
When I try to export from iMovie '11 I get repeated messages that the project is too big. Why? Is there a workaround? (I have already cut a 40-minute movie into three chunks... the first exported to iDVD ok, but the next one of 15 minutes balked for the same reason -- too long...)
I wish I had a mac :-P
Sadly, this is Windows machine so I dont have a non-iOS version of iMovie. I have 2 ideas left. The first is xfering the project to my iPhone 4 and trying to export it there (if that works, awesome but geez apple the iPad 2 is way more powerful than the iphone 4.. youd think I wouldnt even have to attempt this). The 2nd idea is to start at the end of my movie and delete clips and sounds backwards, trying to export each time to find whatever clip is causing the issue (when the movie was 5 minutes it mixed no probem, so I only need to go that far).
Wish me luck?
Also, is anyone else besides me and the 5 dudes in the other threads having this issue?? Speak up, guys - Apple cant a fix a problem they dont know about. -
The default height of message box is too big
Jdev 11.1.2.4.
There is too much space in message box.
I'm not sure when it becomes like this, but it was fine in some older versions
Code:
FacesContext.getCurrentInstance().addMessage(null, new FacesMessage(FacesMessage.SEVERITY_INFO, "title","detail"));
Snapshot (sorry the forum does not support it. it's 10 + cms high on my screen by default, can resize it to a bit smaller height manually, but still too big)
How to make it shorter? Thanks.Maybe this can help: https://blogs.oracle.com/groundside/entry/controlling_the_sizing_of_the
Dario -
Slideshow issue - message "file too big"
I have 120 photos in my slideshow, around 350 MB only. But when trying to save on usb, message saying file is 7.3 GB (too big). After I took away a couple of pictures, it saved - final size is only 395 MB. How can 2 photos make that much difference in size! Is there a glitch with iphoto?
Then try export to the desktop first, and drag the movie to the USB.
-
I had sent an email that was too big to go. It keeps popping into my "Recovered Messages folder I empty my "Recovered Messages"& it comes Back & its blocking all my incoming emails
First, you need to show folders and files which are normally invisible. To do this, open Terminal in Utilities and copy/paste
defaults write com.apple.finder AppleShowAllFiles -bool true
Hit return, then copy/paste
killall Finder
and hit return again.
Next hit Cmd-Shift-G and enter ~/Library/Mail and hit return
Open the triangle next to Mail and look for a file named
.OfflineCache file
and move it to the Trash. If this file exists, doing this will probably fix the problem.
You will need to reverse the show hidden command by just adding false to it, instead of true and them killall Finder again. -
Cannot receive photos via text messaging, says too big to receive
I can receive photos via blue tooth but when anybody sends photos via text it does not arrive or I am told that the image is too big.
Hi,
Thank you for posting the issue here and providing more information. I did some research on the carrier and this is what I found about sending a receiving messages.
Please call your service provider to find out if there are any limitations on attachment sized for your phone plan.
I tried looking up to verify how to manually set up email for the email app for your phone, but was not sure what model you had: please check here for troubleshooting info [http://www.vodafone.com.au/help/devices/ota-settings] if the email is already set up, please ignore.
This lists the networks that work best for sending and receiving pxt in mms overseas and email
[http://support.vodafone.com.au/articles/FAQ/Sending-PXT-to-overseas-numbers]
PXT®/MMS settings [http://support.vodafone.com.au/articles/FAQ/PXT-MMS-settings]
If this continues after any optimizing changes the service provider recommends:
*Are there download settings set in the email menu
*What is the size of the attachment when this happens?
*Is it a specific file type this consistently happens?
*what kind of email account does this happen with, and is it consistent for other emails as well? If so it may be the apn settings.
If you are unable to access the images from the account with Vodafone, it may be the following bugs that is affecting this.
*[https://bugzilla.mozilla.org/buglist.cgi?quicksearch=image+email+firefox+os]
*Does it happen with pdfs? [https://bugzilla.mozilla.org/show_bug.cgi?id=825318]
*Does is happen when there is no message?
*Does it happen when it is too large and is there a message? [https://bugzilla.mozilla.org/show_bug.cgi?id=949972] -
Import Message - Files Too Big
While doing my initial import, I got a message the end that about 8 of my 1000 or so photos were not imported because they were too big. I'm leaving the photos on my NAS drive (not moving them). What's the problem? Thanks in advance for any help.
SteveNo files 10K pixels a side or larger will be imported regardless of Mb size.
From Help: About file formats
>TIFF format
>Tagged-Image File Format (TIFF, TIF) is used to exchange files between applications and computer platforms. TIFF is a flexible bitmap image format supported by virtually all paint, image-editing, and page-layout applications. Also, virtually all desktop scanners can produce TIFF images. Lightroom supports large documents saved in TIFF format (up to 100 million pixels with pixel dimensions of no more than 10,000 on a side). However, most other applications, including older versions of Photoshop (pre-Photoshop CS), do not support documents with file sizes greater than 2 GB.
Don
Don Ricklin, MacBook 1.83Ghz Duo 2 Core running 10.4.8 & Win XP, Pentax *ist D
http://donricklin.blogspot.com/ -
Help
I have tried to send a big message that now seems to be stuck. The outbox has disappeared so there's no way of deleting it. How can I access the outbox to get rid of it?I clicked on an add for Firefox that appeared on my in box. Up came a window saying that I can't access Firefox from my IPad. I can't get rid of this window as there is no x or Done feature.
-
I tried to download a free app. It came up with an error message saying it was too big to download and that I need to connect to WiFi. The icon is still displayed and I can't delete it (I've decided I don't want it. Can anyone tell me how to delete it - there's no x displayed on the icon. Thanks
Hi stripers
You will either a) need to connect to WiFi and complete the download or b) dock your iPad and remove it from the apps list once synced (your iTunes will more then likely want to complete the download first also, which you may be able to cancel in the downloads section).
Regards
Damon -
DBIF_RSQL_INVALID_RSQL statement too big
Hi All,
We are on SAP R/3 4.6C (kernel 46D 64 bit pacth 2113 with last DBLS library, AIX 5.2, DB2 7.1 on z/os 1.4) and for a BW extraction we have the following dump:
"ABAP runtime error DBIF_RSQL_INVALID_RSQL, RSQL error 13 occurred.
The following message also appears in the developer trace:
B *** ERROR => dbtran ERROR (set_input_da_spec): statement too big
B marker count = 1195 > max. marker count = 726."
For the OSS note 655018 the limit of marker count is 2000, but in the trace of work process we read 726.
Many thanks for your help
BobHi Bernhard,
thak you for reply. This is the dump:
============================================================
ABAP runtime errors DBIF_RSQL_INVALID_RSQL
Occurred on 16.01.2008 at 10:29:04
RSQL error 13 when accessing table "EKKO ".
What happened?
The current ABAP/4 program "SAPDBERM " had to be terminated because
one of the statements could not be executed.
This is probably due to an error in the ABAP/4 program.
What can you do?
Note the actions and input that caused the error.
Inform your SAP system administrator.
You can print out this message by choosing "Print". Transaction ST22
allows you to display and manage termination messages, including keeping
them beyond their normal deletion date.
Error analysis
The SQL statement generated from SAP Open SQL violates a
restriction imposed by the database system used in R/3.
For details, refer to either the system log or the developer trace.
Possible reasons for error:
o Maximum size of an SQL statement exceeded.
o The statement contains too many input variables.
o The input data requires more space than is available.
o ...
You can usually find details in the system log (SM21) and in
the developer trace of the relevant work process (ST11).
In the event of an error, the developer trace often gives the
current restrictions.
How to correct the error
The SAP Open SQL statement concerned must be divided into several
smaller units.
If the problem occurred because an excessively large table was used
in an IN itab construct, you can use FOR ALL ENTRIES instead.
When you use this addition, the statement is split into smaller units
according to the restrictions of the database system used.
System environment
SAP Release.............. "46C"
Application server....... "R3PRD"
Network address.......... "172.24.10.50"
Operating system......... "AIX"
Release.................. "5.2"
Hardware type............ "00C7A3EC4C00"
Database server.......... "r3prddb_gb"
Database type............ "DB2"
Database name............ "PRD"
Database owner........... "SAPR3"
Character set............ "en_US.ISO8859-1"
SAP kernel............... "46D"
Created on............... "Aug 25 2005 20:51:50"
Created in............... "AIX 1 5 00447C4A4C00"
Database version......... " "
Patch level.............. "2113"
Patch text............... " "
Supported environment....
Database................. "DB2 for OS/390 6.1"
SAP database version..... "46D"
Operating system......... "AIX 1 4, AIX 2 4, AIX 3 4, AIX 1 5, AIX 2 5, AIX 3
5, , System build information:, -
, LCHN :
775484"
User, transaction...
Client.............. 300
User................ "ALEREMOTE"
Language key........ "E"
Transaction......... " "
Program............. "SAPDBERM "
Screen.............. "SAPMSSY0 1000"
Screen line......... 6
Information on where termination occurred
The termination occurred in the ABAP/4 program "SAPDBERM " in
"PUT_EKKO".
The main program was "AQZZSYSTBWGENER0SY000000000361 ".
The termination occurred in line 333
of the source code of program "SAPDBERM " (when calling the editor 3330).
The program "SAPDBERM " was started as a background job.
Source code extract
003030 ENDFORM.
003040
003050 ----
003060 FORM PUT_EKKO.
003070
003080 CONSTANTS: LC_PACKAGE_SIZE LIKE SY-TFILL VALUE 10.
003090 DATA: BEGIN OF LT_SEKKO OCCURS 0,
003100 EBELN LIKE EKKO-EBELN,
003110 END OF LT_SEKKO.
003120 DATA: BEGIN OF LT_TEKKO OCCURS 0,
003130 EBELN LIKE EKKO-EBELN,
003140 END OF LT_TEKKO.
003150 DATA: L_INDEX_FROM LIKE SY-TABIX,
003160 L_INDEX_TO LIKE SY-TABIX,
003170 L_EKPO_TABIX LIKE SY-TABIX.
003180 PERFORM KSCHL_SETZEN.
003190 ONEST = P_ONEST.
003200 TEST = TESTLAUF.
003210 DB_DEL = ' '. "VETVG und Komponenten bleiben noch stehen
003220 DETPROT = P_PROT.
003230 ANDAT = ER_ANDAT.
003240 PERFORM AKTIVITAET_SETZEN(SAPFM06D) USING '06'.
003250 SELECT EBELN FROM EKKO INTO TABLE LT_SEKKO
003260 WHERE EBELN IN ER_EBELN
003270 AND EKORG IN ER_EKORG
003280 AND BSTYP IN ER_BSTYP
003290 AND BEDAT IN ER_BEDAT
003300 AND BSART IN ER_BSART
003310 AND EKGRP IN ER_EKGRP
003320 * AND MEMORY NE 'X'
> ORDER BY EBELN.
003340 L_INDEX_FROM = 1.
003350
003360 DO.
003370 REFRESH LT_TEKKO.
003380 L_INDEX_TO = L_INDEX_FROM + LC_PACKAGE_SIZE - 1.
003390 LOOP AT LT_SEKKO FROM L_INDEX_FROM
003400 TO L_INDEX_TO.
003410 APPEND LT_SEKKO TO LT_TEKKO.
003420 ENDLOOP.
003430 IF SY-SUBRC NE 0.
003440 EXIT.
003450 ENDIF.
003460 SELECT * FROM EKKO INTO TABLE XEKKO
003470 FOR ALL ENTRIES IN LT_TEKKO
003480 WHERE EBELN = LT_TEKKO-EBELN
003490 ORDER BY PRIMARY KEY.
003500 SELECT * FROM EKPO INTO TABLE XEKPO
003510 FOR ALL ENTRIES IN LT_TEKKO
003520 WHERE EBELN = LT_TEKKO-EBELN
Contents of system fields
SY field contents..................... SY field contents.....................
SY-SUBRC 0 SY-INDEX 0
SY-TABIX 1 SY-DBCNT 152
SY-FDPOS 1 SY-LSIND 0
SY-PAGNO 0 SY-LINNO 1
SY-COLNO 1
============================================================
We have also installed the last kernel and the DBSL 2342.
Thank you and regards
Bob
Maybe you are looking for
-
How do i delete my credit card information from my account while keeping the account ?
I want to delete my credit card information from my APPLE ID but there is no NONE button, how do i do this ?!?!?
-
Need to chg text of a field in SM30: Compare Flag
Hi, I created a table & created a table maintance Generator. I want to change the text of a field in SM30. Currently it is taking from Dictonary Field text. I went to SE11->Table Maintance Generator-> Modification->Maintance Screen->Flow Logic There
-
IPhoto 11 retouch tool: grab not working
Using iPhoto's retouch tool, I want to grab some pixels from one area and put them into another. Apple support instructions say: ...you can "grab" pixels from another part of the photo and apply them to the blemish. Pres
-
ZAV 8 - howto image fat cli/editable xml file on local PC...
I have a fat client we want to image with ZAV 8. The issue is that there is an xml file on each local PC similiar to a TNS file it needs to use. How do I use ZAV 8 with this fat client and be able to point to the xml file on each individual PC? I've
-
Hi, I am trying to create a script who could act as an Autocad plot (ie convert each color to black, with a different lineweight). I did some research, and tried to mix some scripts found here to create my own, but there is a lot of things I don't un