Relaying to Specific Domain

What is the best practice for relaying messages sent externally to a specific domain? I'm not talking about relaying from outside Ironport then back to your email servers. I'm talking about relaying the other direction. So for example your email server sends and email from abc.com to Ironport, I want something on Ironport that says any email from abc.com relay to this IP or domain. Can that only be done using a Outgoing Content Filter?
The goal is to have emails sent to a certain domain directed from Ironport to a vpn tunnel.

Depending on incoming vs. outgoing --- just create a content filter w/ alt-mailhost... and then also be sure to create an SMTP route for that alt-mailhost domain...
Similar to --->
SMTP route --->
In my example --- I'm not really routing anywhere --- so, I am using /dev/null.
Testing --- standard SMTP telnet --->
mail from: [email protected]
250 sender <[email protected]> ok
rcpt to: [email protected]
250 recipient <[email protected]> ok
data
354 go ahead
subject: THIS IS A TEST
HELLO
250 ok: Message 202 accepted
Watching mail_logs --->
Tue Apr 29 18:11:36 2014 Info: MID 202 ICID 610 From: <[email protected]>
Tue Apr 29 18:11:41 2014 Info: MID 202 ICID 610 RID 0 To: <[email protected]>
Tue Apr 29 18:11:49 2014 Info: MID 202 Subject 'THIS IS A TEST'
Tue Apr 29 18:11:49 2014 Info: MID 202 ready 153 bytes from <[email protected]>
Tue Apr 29 18:11:49 2014 Info: MID 202 matched all recipients for per-recipient policy DEFAULT in the inbound table
Tue Apr 29 18:11:49 2014 Info: MID 202 interim verdict using engine: CASE spam negative
Tue Apr 29 18:11:49 2014 Info: MID 202 using engine: CASE spam negative
Tue Apr 29 18:11:49 2014 Info: MID 202 Outbreak Filters: verdict negative
Tue Apr 29 18:11:49 2014 Info: MID 202 queued for delivery
Tue Apr 29 18:11:49 2014 Info: Delivery start DCID 0 MID 202 to RID [0]
Tue Apr 29 18:11:49 2014 Info: Message done DCID 0 MID 202 to RID [0]
Tue Apr 29 18:11:49 2014 Info: MID 202 RID [0] Response '/dev/null'
Tue Apr 29 18:11:49 2014 Info: Message finished MID 202 done
Message is sent where I wanted it... /dev/null.
I hope this helps!
-Robert
(*If you have received the answer to your original question, and found this helpful/correct - please mark the question as answered, and be sure to leave a rating to reflect!)

Similar Messages

Configure SMTP to forward mail to a specific domain

We have migrated all of our e-mail from on premise exchange to Office 365. To support internal applications that send e-mail such as our scanners, we have setup a SMTP relay server using IIS on Windows 2012.
This is working very well however we have some users that when they do a scan they simply enter their e-mail alias (the part before the @ symbol) since that worked when the scanner was sending to Exchange. However Office 365 does not know how to route these
e-mails so they result in a NDR. Since the NDR is not sent to the person creating the scan they do not even know the issue other than they did not receive their scan.
Is there a way to configure the SMTP service on Windows 2012 to send all e-mail that does not have a domain listed in the e-mail address to a specific domain? For example, if someone were to send their scan to myalias it would be delivered to myalias at mycompany
dot com (sorry about spelling it out but it is not letting me post this with a e-m ail address in it even if the address is not valid)

Hi,
You can try to create a SMTP domain in IIS manager(Default SMTP Virtual Server>Domains>New>domain) and then enable "Allow incoming mail to be relayed to this domain" and "Forward all mail to smart host".
In addition, for questions related to IIS, you can also ask in IIS forum for professional assistance:
http://forums.iis.net/
Best regards,
Susie
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Hold email for specific domain

Is there a way to hold outbound-email only for a specific domain/user, without interrupting other users?

Hi Alex,
The new primary mail server is not available due to an issue with the ISP, so all mail is being delivered to the backup mx server (which is on both the new & old DNS MX records).
The problem is that the backup MX server's DNS servers are using the old records (as the previous DNS NS records had an expire time of 7 days) and therefore relaying the email to an old ISP's relay servers (which then try to relay to an old IP address, so the email consequently gets lost).
Ideally I would just flush the cache on the DNS servers, but I have no control over these, and the guys that manage them will not be in their office until tomorrow morning and I don't know if they will do this anyway.
I know it is a far from perfect configuration, but hopefully you maybe able to suggest a solution

Is it possible to restrict the ability to e-mail a pdf outside a specific domain name?

Hello,
I am trying to find a solution to a friends problem. She has a quarterly publication that she sends out to big banks and financial institutions. Recently she has had some problems with press leaks. I am trying to find some security options for her however the task is difficult. Because these institutions have firewalls I am not sure encrypting or tracking is the right answer because the publication might not make it through. She wants users to be able to print the publication because many of the readers are older and prefer to read during their commute and at home. Essentially I am looking for any ways to make readers think twice about sharing the information. I thought if I could restrict e-mail to a specific domain name that would help this way users can only e-mail within their specific company. If any one has any suggestions please feel free to share.

Thank you Todd, I was able to get it to work but I do have a few more questions...
1) When I tested this, at the top of the message, before any of the text I created, this showed up: This is a multi-part message in MIME format. --------------040406040801080102080500 Content-Type: text/html; charset=ISO-8859-1 Content-Transfer-Encoding: 7bit
2) After the signature line, this showed up: --------------040406040801080102080500 Content-Type: image/jpeg Content-Transfer-Encoding: base64 Content-ID: /9j/4AAQSkZJRgABAQEAYABgAAD/4QAiRXhpZgAATU0AKgAAAAgAAQESAAMAAAABAAEAAAAA AAD/2wBDAAIBAQIBAQICAgICAgICAwUDAwMDAwYEBAMFBwYHBwcGBwcICQsJCAgKCAcHCg0K CgsMDAwMBwkODw0MDgsMDAz/2wBDAQICAgMDAwYDAwYMCAcIDAwMDAwMDAwMDAwMDAwMDAwM DAwMDAwMDAwMDAwMDAwMDAwMDAwMDAwMDAwMDAwMDAz/wAARCAC5ApUDASIAAhEBAxEB/8QA HwAAAQUBAQEBAQEAAAAAAAAAAAECAwQFBgcICQoL/8QAtRAAAgEDAwIEAwUFBAQAAAF9AQID AAQRBRIhMUEGE1FhByJxFDKBkaEII0KxwRVS0fAkM2JyggkKFhcYGRolJicoKSo0NTY3ODk6 Q0RFRkdISUpTVFVWV1hZWmNkZWZnaGlqc3R1dnd4eXqDhIWGh4iJipKTlJWWl5iZmqKjpKWm p6ipqrKztLW2t7i5usLDxMXGx8jJytLT1NXW19jZ2uHi4+Tl5ufo6erx8vP09fb3+Pn6/
(It was actually much longer than that)
Is there anyway that I can get that to go away? I obviously would prefer a nice, cleanly formatted e-mail to be sent just like I would send if I were creating it on the spot.
Thanks,
Evan

Specific domain blocked for both mail programs

Hi all. Need some help... One specific domain name's email addresses has been blocked by my mac for outgoing email from both 'mail' and entourage programs. I don't get any error messages but the emails never get delivered. However emails from the domain name get delivered to me just fine.
It is isolated to my mac as I can send/receive using a different computer on the same internet connection to the domain name addresses.
I think it results from a moment last week when I accidentally clicked on 'junk' instead of delete for an email from the domain name thats causing the trouble. I immediately clicked 'this is not junk', and thought nothing more of it. it appears that somehow the computer will now not deliver email to the domain name address in question. Its like a very specific block, but effects both mail programs. Apple Support suggested posting to this disscussion board or an 'archive and install'. Hope someone can help. thanks.
iMac Mac OS X (10.4.8)

Open one of these messages in the Sent mailbox, and then click on View in the Menubar of the Mail window, place the cursor on Message, and choose Long Headers from the resulting menu. In the Long Headers, is there on named Message ID#? If so, then the message was sent from this Mac, as the ID# must be reported back from the SMTP.
Are you using Rich Text Format, when composing and sending on this Mac? Do these messages have any attachments, or images such as might be in a Signature? If this is the situation, then the RTF may be getting converted to HTML, and a SPAM filter in front of the recipient may be blocking the receipt of messages from this Mac.
Try resending one of these message, after first changing to Plain Text, as a test. Open the message in the Sent mailbox, click on Message in the Menubar, and choose Send Again. Next click on Format in the Menubar, and choose Make Plain Text, and send.
Keep us posted.
Ernie

Is there a way to "lock" an app tab so that it will stay on a specific domain?

I use our family computer in the living room. I have told them numerous times not to change the app tab because I use it everyday, and I don't want it going to some game site. Unfortunately, they don't care and do it anyway. Is there a way that I can "lock" the tab so that it stays on that specific domain? example: facebook.com

Unfortunately these don't lock tab by domain, but only a current page :( I'm also looking for a solution to enable domain browsing on locked tab. It seems like logical behavior, so I'm really surprised I can't find anything how to achieve it.

Not receiving email to my MobileMe account from one specific domain

Starting 2 days ago I stopped receiving email addressed to my "@mac.com" or "me.com" account from one specific domain. Prior to that I had no problem receiving email from that domain. I have no problems receiving email into my MobileMe accounts from many other senders. People with email addresses under this domain can send emails to my Gmail account from the same origination account and they come through just fine. The emails that do not appear are not in my junk mail and they never get "bounced back" to the sender as undeliverable.
I use Mail under Leopard 10.5.4 with all updates installed.
It sounds to me like this domain has been "blacklisted" by Apple but I have never heard of them doing this.
Any suggestions would appreciated.

petervan 58,
Just this one person? Your .mac account is getting mail from others OK? Does the person have your email address correct on their phone.

Access blob storage files by specific domain. (Prevent hotlinking in Azure Blob Storage)

Hi,
My application deployed on azure, and I managed all my file to blob storage.
When i created container with public permission then it accessible for all anonymous users. When i hit URL of file (blob) from different browser, then i will get that file.
In Our application we have some important file and images that we don't want to expose. When we render HTML page then in <img> tag we define src="{blob file url}" when i mention this then public file are accessible, but same URL i copied
and hit to anther browser then still it is visible. My requirement is my application domain only able to access that public file in blob storage.
Amazon S3 which provide bucket policy where we define that for specific domain only file will accessible. see http://docs.aws.amazon.com/AmazonS3/latest/dev/example-bucket-policies.html
Restricting Access to a Specific HTTP Referrer

hi Prasad,
Thanks for your post back.
All of SAS and CORS could work, but not comprehensive.
For your requirement, " My requirement is my application domain only able to access that public file in blob storage.", If you want to stop the other domain site access your blob, you may need set the CORS for your blob. When
the origin domain of the request is checked against the domains listed for the
AllowedOrigins element. If the origin domain is included in the list, or all domains are allowed with the wildcard character '*', then rules evaluation proceeds. If the origin domain is not included, then the request fails. So other domain didn't access
your resource. You also try the Gaurav's blog:
http://gauravmantri.com/2013/12/01/windows-azure-storage-and-cors-lets-have-some-fun/
If you access CROS resource, you also need use SAS authenticated.
However SAS means that you can grant a client limited permissions to your blobs, queues, or tables for a specified period of time and with a specified set of permissions, without having to share your account access keys. The SAS is a URI that encompasses
in its query parameters all of the information necessary for authenticated access to a storage resource (http://azure.microsoft.com/en-us/documentation/articles/storage-dotnet-shared-access-signature-part-1/
). So if your SAS URI is available and not expired ，this URI could be used to other domain site. I think you can try to test it.
If I misunderstood, please let me know.
Regards,
Will
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Bug: Customizing Convergence banner for a specific domain does not work

Hi,
I'm trying to customize the banner for a specific domain, I was following the steps from the documentation but I found that there is a bug relate: Bug #6749263 And I tried to find if the bug was already resolved in convergence 1.0-7.01 and the search in bugs.sun.com gets nothing.
Does anybody knows if the bug was fixed in convergence 1.0-7.01?
Thanks in advanced.

ofonseca wrote:
I'm trying to customize the banner for a specific domain, I was following the steps from the documentation but I found that there is a bug relate: Bug #6749263 And I tried to find if the bug was already resolved in convergence 1.0-7.01 and the search in bugs.sun.com gets nothing.The bug hasn't been fixed (according to the bug notes).
Regards,
Shane.

Question on Registering MBean on specific Domain

We have a Run-time which is at present modeled as a Domain level MBean. In the MBean descriptor , we have the following snippet for registering
<jmx-runtime-mbean
objectname="EMDomain:name=oracle.sysman.emfa.FADiscovery,type=EMDiscoveryIntegration"
class="oracle.apps.fnd.applcore.topologyMBean.runtime.mbean.FADiscovery"
management-interface="oracle.apps.fnd.applcore.topologyMBean.runtime.mbean.FADiscoveryMXBean">
<description>Fusion Applications Discovery MBean</description>
</jmx-runtime-mbean>
As a result , all the domains are having the above MBean registered. Requirement is that register this MBean only on a specific domain. Is it possible to achieve this by any means?
Thanks
Joseph

R167 wrote:
Go to apple though, tell them what happened, have them discontinue your other iPod, and get a replacement (if covered by warranty) restoring from last backup of other device.
That is entirely incorrect. Apple will NOT discontinue an iPod and theft is NOT covered by the warranty.
Remember, in order to do most things, you need to have the ipod unlocked before connecting to a computer.
Yes, but most common thieves know how to place it in Recovery Mode, thus bypassing the passcode.

Getting the mailserver of a specific domain

Hello,
does someone know how I can get the mailserver for lets say hotmail.com from a dns-server??
I can contact my dns server with a socket, but I don't know how to talk with this protocol to get any information from it. I want to ask it what the mailserver adress is for a specific domain.
Please help me!!
Thanks,
Daniel

You need to retrieve the MX-records from the zone.
The MX-records are in fact the mailservers used to receive mail.
To make it simple you can use "DNS Package" from Sinotar.
It seems to be free for personal use.
http://www.sinotar.com/english/download.html

Delegate specific domain user to do add/remove hardware&software, join to domain feature only.

Dear team;
I want to Delegate specific domain user to do two things add/remove hardware/software, join to domain feature only without give him Local admin
Best regards
LAshkham

Hi,
Please understand that if you want make some specific domain users add/remove hardware/software on domain computers, you should grant these users the local admin right. We could grant the local
admin right using Restricted Groups Policy Settings or Local Users and Groups GPP setting. For details, please refer to the following articles.
Restricted Groups Policy Settings
http://technet.microsoft.com/en-us/library/cc756802(v=ws.10).aspx
How to use Group Policy Preferences to Secure Local Administrator Groups
http://www.grouppolicy.biz/2010/01/how-to-use-group-policy-preferences-to-secure-local-administrator-groups/
You also mentioned that you want to delegate the
Join a computer to a domain task to these specific users. Regarding the request, we could delegate the task via Delegation of Control Wizard. For details, please refer to the following article.
Delegation of Control Wizard
http://technet.microsoft.com/en-us/library/dd145344.aspx
Hope this helps.
Best Regards,
Andy Qi
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.
Andy Qi
TechNet Community Support

Configure TLS inbound for specific domain

Hi All,
would like to configure TLS inbound for specific domain . am using exchange 2010 and instead of edge we are using Trend Micro IMSS Gateway. now please explain me how to configure TLS for inbound but for specific domain
have gone through their documents but when i checked there is a tab for Trusted CA certificated. i have imported out ORG publicly trusted certificate and have selected mutual TLS. but no luck it now allowing the TLS inbound.
Please help me on this
Thanks, Venkatesh. "Hardwork Never Fails"

Hi imvenkat,
I recommend you ask this in
Trend Micro forum also, since you are using Trend Micro gateway instead of exchange edge server.
Best Regards,
Niko Cheng
TechNet Community Support

Not receiving emails from one specific domain

Hi,
I'm having problems with not receiving emails from one specific domain @youmail.dk. It hasn't been an issue earlier, but I stopped receiving the emails late last year. For all I know this is the only domain there's a problem with - I don't have any problems with any other random domain.
There is no rules or anything like that set up, so I have no idea what the problem could be... There's no "failure to deliver" notification send to the sender either.
It doesn't matter if I check iCloud online, on my MacBook or iPhone...
Can anyone help me?
Nina.

Comcast Security Assurance manages email system security and should be able to help you with this. Call them at 1-888-565-4329 (from http://constantguard.comcast.net/dedicated-support/). They will probably want to know the IP address(es) and/or host name(s) of the sending email server(s).
The first-line reps at CSA are sometimes not so helpful. If so, be persistent, and keep at them until you get a satisfactory answer.

Channel for incoming mail addressed to specific domain

I am trying to create a channel for all incoming messages addressed to a specific domain.
I know that all incoming Internet mails go to tcp_local first.
What I want to do is to separate mails for different domains to different channels so I could later process them, either with conversion channel or with some channel filters.
Also, after passing trough those specific channels, how to put those mails back on track for delivery?
Can anyone help on doing this?
Thanks
I�m running (on Solaris 8) MS5.2p1 hf1.21

To look over the docs� but I already did, and it�s pretty bad, poorly explained�
So, please let�s try to make this clear.
Note, every time after making changes I run:
imsimta cnbuild
imsimta restart
First, you gave an example to me (reply 5):
[email protected]%tcp_friendly-daemon
Second, I was not sure from your post where to put space (reply6), and I tested both cases:
domain.net$E$F [email protected]%tcp_friendly-daemon # space between $F and $U
and
domain.net [email protected]%tcp_friendly-daemon # space between domain.net and $E
Unfortunately, nothing has changed.
Third, you wrote (reply 7) �No spaces�.
Forth, I tested that as well and it gave me an error (reply 8).
Fifth, in your last reply (reply 9) you said that I need a left and a right half, and you suggested an example that I�ve already checked (reply 6) and it wasn�t working :(
So, now I am completely lost�
Here is the result of testing this last example in imta.cnf:
domain.net [email protected]%tcp_friendly-daemon # space between domain.net and $E
! tcp_friendly
tcp_friendly smtp mx single_sys subdirs 20 noreverse maxjobs 7 pool SMTP_POOL mailfromdnsverify maytlsserver allowswitchchannel saslswitchchannel tcp_auth
tcp_friendly-daemon
imsimta cnbuild
imsimta restart
imsimta test -rewrite -debug [email protected]
Could you review this result, please and try to see what is wrong.
Initializing mm_.
Initializing mm_ submission.
Checking identifiers.
*** Debug output from initializing MM for submission:
13:43:32.79: mmc_winit('l','postmaster@machine_name.test.com','0IB800802GOK8O@machine_name.test.com') called.
13:43:32.79: Queue area size 5858064, temp area size 5858064
13:43:32.79: 1464516 blocks of effective free queue space available; setting disk limit accordingly.
13:43:32.79: Rewriting: Mbox = "postmaster", host = "machine_name.test.com", domain = "$*", literal = "", tag = ""
13:43:32.79: Rewrite: "$*", position 0, hash table -
13:43:32.79: Found: "$E$F$U%$H@machine_name.test.com$V$H"
13:43:32.79: Rewrite failed, not forward.
13:43:32.79: Rewrite: "$*", position 1, hash table -
13:43:32.79: Failed.
13:43:32.79: Rewrite: "$*", position 0, rewrite database -
13:43:32.79: Failed
13:43:32.79: Rewriting: Mbox = "postmaster", host = "machine_name", domain = "machine_name.test.com", literal = "", tag = ""
13:43:32.79: Rewrite: "machine_name.test.com", position 0, hash table -
13:43:32.79: Found: "$U%$D@machine_name.test.com"
13:43:32.79: New mailbox: "postmaster".
13:43:32.79: New host: "machine_name.test.com".
13:43:32.79: New route: "machine_name.test.com".
13:43:32.79: New channel system: "machine_name.test.com".
13:43:32.79: Looking up host "machine_name.test.com".
13:43:32.79: - found on channel l
13:43:32.79: Routelocal flag set; scanning for % and !
13:43:32.79: Rewriting: Mbox = "postmaster", host = "machine_name.test.com", domain = "$*", literal = "", tag = ""
13:43:32.79: Rewrite: "$*", position 0, hash table -
13:43:32.79: Found: "$E$F$U%$H@machine_name.test.com$V$H"
13:43:32.79: Rewrite failed, not forward.
13:43:32.79: Rewrite: "$*", position 1, hash table -
13:43:32.79: Failed.
13:43:32.79: Rewrite: "$*", position 0, rewrite database -
13:43:32.79: Failed
13:43:32.79: Rewriting: Mbox = "postmaster", host = "machine_name", domain = "machine_name.test.com", literal = "", tag = ""
13:43:32.79: Rewrite: "machine_name.test.com", position 0, hash table -
13:43:32.79: Found: "$U%$D@machine_name.test.com"
13:43:32.79: New mailbox: "postmaster".
13:43:32.79: New host: "machine_name.test.com".
13:43:32.79: New route: "machine_name.test.com".
13:43:32.79: New channel system: "machine_name.test.com".
13:43:32.79: Looking up host "machine_name.test.com".
13:43:32.79: - found on channel l
13:43:32.79: Routelocal flag set; scanning for % and !
13:43:32.79: Mapped return address: postmaster@machine_name.test.com
*** Debug output from rewriting a forward header address:
13:43:32.79: Rewriting: Mbox = "user", host = "domain.net", domain = "$*", literal = "", tag = ""
13:43:32.79: Rewrite: "$*", position 0, hash table -
13:43:32.79: Found: "$E$F$U%$H@machine_name.test.com$V$H"
13:43:32.79: Rewrite failed, not envelope.
13:43:32.79: Rewrite: "$*", position 1, hash table -
13:43:32.80: Failed.
13:43:32.80: Rewrite: "$*", position 0, rewrite database -
13:43:32.80: Failed
13:43:32.80: Rewriting: Mbox = "user", host = "domain", domain = "domain.net", literal = "", tag = ""
13:43:32.80: Rewrite: "domain.net", position 0, hash table -
13:43:32.80: Found: "[email protected]%tcp_friendly-daemon"
13:43:32.80: Rewrite failed, not envelope.
13:43:32.80: Rewrite: "domain.net", position 1, hash table -
13:43:32.80: Failed.
13:43:32.80: Rewrite: "domain.net", position 0, rewrite database -
13:43:32.80: Failed
13:43:32.80: Rewriting: Mbox = "user", host = "domain", domain = ".net", literal = "", tag = ""
13:43:32.80: Rewrite: "*.net", position 0, hash table -
13:43:32.80: Failed
13:43:32.80: Rewrite: ".net", position 0, hash table -
13:43:32.80: Found: "$U%$H$D@TCP-DAEMON"
13:43:32.80: New mailbox: "user".
13:43:32.80: New host: "domain.net".
13:43:32.80: New route: "TCP-DAEMON".
13:43:32.80: New channel system: "TCP-DAEMON".
13:43:32.80: Looking up host "TCP-DAEMON".
13:43:32.80: - found on channel tcp_local
13:43:32.80: Rewrite rules result: [email protected]
13:43:32.80: Checking reverse URL cache for: [email protected]
13:43:32.80: Applying reverse URL pattern ldap:///$V?mail?sub?$Q to: [email protected]
13:43:32.85: Resulting URL: ldap:///o%3Ddomain.net%2Co%3Disp?mail?sub?(|([email protected])([email protected]))
13:43:32.85: mmc_open_url called to open ldap:///o%3Ddomain.net%2Co%3Disp?mail?sub?(|([email protected])([email protected])), flags = 256
13:43:32.85: URL with quotes stripped: ldap:///o%3Ddomain.net%2Co%3Disp?mail?sub?(|([email protected])([email protected]))
13:43:32.85: LDAP URL identified
13:43:32.85: URL context #1 will be used
13:43:32.85: Performing URL search on: ldap:///o%3Ddomain.net%2Co%3Disp?mail?sub?(|([email protected])([email protected]))
13:43:32.86: mmc_read_url result: [email protected]
13:43:32.86: URL resolution returned: [email protected]
forward channel = l
channel description =
channel user filter =
dest channel filter =
source channel filter =
channel flags #0 = BIDIRECTIONAL MULTIPLE IMMNONURGENT NOSERVICEALL
channel flags #1 = NOSMTP DEFAULT
channel flags #2 = COPYSENDPOST COPYWARNPOST POSTHEADONLY HEADERINC NOEXPROUTE
channel flags #3 = LOGGING NOGREY NORESTRICTED RETAINSECURITYMULTIPARTS
channel flags #4 = EIGHTBIT NOHEADERTRIM NOHEADERREAD RULES
channel flags #5 =
channel flags #6 = LOCALUSER REPORTHEADER
channel flags #7 = NOSWITCHCHANNEL NOREMOTEHOST DATEFOUR DAYOFWEEK
channel flags #8 = NODEFRAGMENT EXQUOTA REVERSE NOCONVERT_OCTET_STREAM
channel flags #9 = NOTHURMAN INTERPRETENCODING USEINTERMEDIATE RECEIVEDFROM VALIDATELOCALSYSTEM NOTURN
defaulthost = test.com test.com
linelength = 1023
channel env addr type = SOURCEROUTE
channel hdr addr type = SOURCEROUTE
channel official host = machine_name.test.com
channel queue 0 name = LOCAL_POOL
channel queue 1 name = LOCAL_POOL
channel queue 2 name = LOCAL_POOL
channel queue 3 name = LOCAL_POOL
channel after params =
channel user name =
urgentnotices = 1 2 4 7
normalnotices = 1 2 4 7
nonurgentnotices = 1 2 4 7
channel rightslist ids =
local behavior flags = %x7
backward channel = tcp_local
header To: address = [email protected]
header From: address = [email protected]
envelope To: address = [email protected] (route (machine_name.test.com,machine_name.test.com)) (host domain.net)
envelope From: address = [email protected]
name =
mbox = user
Extracted address action list:
[email protected]
Extracted 733 address action list:
[email protected]
Address list expansion:
user%domain.net@ims-ms-daemon
1 expansion total.
*** Debug output from submitting an envelope address:
13:43:32.88: mmc_wadr(0x0018a888,'[email protected]','[email protected]') called.
13:43:32.88: Copy estimate before address addition is 1
13:43:32.88: Parsing address [email protected]
13:43:32.88: Rewriting: Mbox = "user", host = "domain.net", domain = "$*", literal = "", tag = ""
13:43:32.88: Rewrite: "$*", position 0, hash table -
13:43:32.88: Found: "$E$F$U%$H@machine_name.test.com$V$H"
13:43:32.88: Match, pattern = "domain.net", current = "(*domaincheck*)"
13:43:32.88: old state = not checked.
13:43:32.88: Using result 1 from domain match cache.
13:43:32.88: new state = succeeded.
13:43:32.88: New mailbox: "user".
13:43:32.88: New host: "domain.net".
13:43:32.88: New route: "machine_name.test.com".
13:43:32.88: New channel system: "machine_name.test.com".
13:43:32.88: Looking up host "machine_name.test.com".
13:43:32.88: - found on channel l
13:43:32.88: Routelocal flag set; scanning for % and !
13:43:32.88: Address [email protected] requires local processing.
13:43:32.88: Variant #1 = [email protected]
13:43:32.89: Variant #2 = *@domain.net
13:43:32.89: Checking for [email protected] in the system alias file
13:43:32.89: - not found
13:43:32.89: Checking for *@domain.net in the system alias file
13:43:32.89: - not found
13:43:32.89: Checking [email protected] with URL template ldap:///$V?*?sub?$R
13:43:32.89: LDAP URL template identified
13:43:32.89: URL determined to be: ldap:///o%3Ddomain.net%2Co%3Disp?*?sub?(|([email protected])([email protected])([email protected]))
13:43:32.89: URL context #1 will be used
13:43:32.89: Using cached LDAP result for URL info: ldap:///$V?*?sub?$R|[email protected]|[email protected]
13:43:32.89: Scanning LDAP result.
13:43:32.89: Attribute: objectclass
13:43:32.89: Attribute index: 0
13:43:32.89: Attribute: inetuserstatus
13:43:32.89: Attribute index: 1
13:43:32.89: Attribute: mailuserstatus
13:43:32.89: Attribute index: 2
13:43:32.89: Attribute: uid
13:43:32.89: Attribute index: 4
13:43:32.89: Attribute: mail
13:43:32.89: Attribute index: 5
13:43:32.89: Attribute: mailhost
13:43:32.89: Attribute index: 9
13:43:32.89: Attribute: mailDeliveryOption
13:43:32.89: Attribute index: 18
13:43:32.89: Attribute: preferredLanguage
13:43:32.89: Attribute index: 42
13:43:32.89: Scanning complete, begin actions
13:43:32.89: Object class: top
13:43:32.89: Object class didn't match
13:43:32.89: Object class: person
13:43:32.89: Object class didn't match
13:43:32.89: Object class: organizationalPerson
13:43:32.89: Object class didn't match
13:43:32.89: Object class: inetOrgPerson
13:43:32.89: Object class didn't match
13:43:32.89: Object class: inetUser
13:43:32.89: Object class didn't match
13:43:32.89: Object class: ipUser
13:43:32.89: Object class didn't match
13:43:32.89: Object class: nsManagedPerson
13:43:32.89: Object class didn't match
13:43:32.89: Object class: userPresenceProfile
13:43:32.89: Object class didn't match
13:43:32.89: Object class: inetMailUser
13:43:32.89: Object class match, reference value 1
13:43:32.89: Object class: inetLocalMailRecipient
13:43:32.89: Object class match, reference value 18
13:43:32.89: User/group index = 1
13:43:32.89: Domain is active
13:43:32.89: Mail domain is active
13:43:32.89: User status = active
13:43:32.89: Mail user status = active
13:43:32.89: User UID user found.
13:43:32.89: Processing mailhost attribute machine_name.test.com
13:43:32.89: Mailhost references local system
13:43:32.89: Delivery option: mailbox
13:43:32.89: Delivery options value: 1
13:43:32.89: No reprocess flag on user, processing now
13:43:32.89: Status for this address = 1
13:43:32.89: - URL match for [email protected]
13:43:32.89: Delivery option template: $M%$\$2I$_+$2S@ims-ms-daemon
13:43:32.89: - user%domain.net@ims-ms-daemon
13:43:32.89: Parsing address user%domain.net@ims-ms-daemon
13:43:32.90: Rewriting: Mbox = "user%domain.net", host = "ims-ms-daemon", domain = "$*", literal = "", tag = ""
13:43:32.90: Rewrite: "$*", position 0, hash table -
13:43:32.90: Found: "$E$F$U%$H@machine_name.test.com$V$H"
13:43:32.90: Match, pattern = "ims-ms-daemon", current = "(*domaincheck*)"
13:43:32.90: old state = not checked.
13:43:32.90: Using result 0 from domain match cache.
13:43:32.90: new state = fail pending.
13:43:32.90: Rewrite failed due to channel mismatch.
13:43:32.90: Rewrite: "$*", position 1, hash table -
13:43:32.90: Failed.
13:43:32.90: Rewrite: "$*", position 0, rewrite database -
13:43:32.90: Failed
13:43:32.90: Rewriting: Mbox = "user%domain.net", host = "ims-ms-daemon", domain = "ims-ms-daemon", literal = "", tag = ""
13:43:32.90: Rewrite: "ims-ms-daemon", position 0, hash table -
13:43:32.90: Failed.
13:43:32.90: Rewrite: "ims-ms-daemon", position 0, rewrite database -
13:43:32.90: Failed
13:43:32.90: Looking up host "ims-ms-daemon".
13:43:32.90: - found on channel ims-ms
13:43:32.90: - orig_send_access mapping check: l|postmaster@machine_name.test.com|l|[email protected]
13:43:32.90: - passed.
13:43:32.90: - send_access mapping check: l|postmaster@machine_name.test.com|ims-ms|user%domain.net@ims-ms-daemon
13:43:32.90: - passed.
13:43:32.90: - adding address user%domain.net@ims-ms-daemon to channel ims-ms
13:43:32.90: - adding address [email protected] to headers.
13:43:32.90: Copy estimate after address addition is 2
Expanded address:
[email protected]
Submitted address list:
ims-ms
user%domain.net@ims-ms-daemon (orig [email protected], inter [email protected], host ims-ms-daemon) NOTIFY-FAILURES NOTIFY-DELAYS
Submitted notifications list:

Relaying to Specific Domain

Similar Messages

Maybe you are looking for