Remotely Access router 2811 via AUX and modem speed configuration

I have got 2811 router that is connected to analogue modem (56000), and my PC is connected to another analogue modem (33000)
The intial configuration for the router was :
Router2811#show run | begin line aux
line aux 0
exec-timeout 20 0
password xxx
logging synchronous
login
modem InOut
stopbits 1
flowcontrol hardware
Router2811#show line
Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 0 CTY - - - - - 0 0 0/0 -
* 1 1 AUX 9600/9600- inout - - - 0 0 10/0 -
322 322 VTY - - - - - 0 0 0/0 -
323 323 VTY - - - - - 0 0 0/0 -
324 324 VTY - - - - - 0 0 0/0 -
325 325 VTY - - - - - 0 0 0/0 -
326 326 VTY - - - - - 0 0 0/0 -
Line(s) not in async mode -or- with no hardware support:
2-321
It did not work when remotely I tried to login to the router !!! it kept disconne
What I did was this :
Router2811#config ter
Router2811(config)#line 1
Router2811(config-line)# modem autoconfiguration discovery
The router automatically discover modem's speed 115200 and replaced the 9600 in the configuration above.
Router2811#show run | begin line aux
line aux 0
exec-timeout 20 0
password 7 1040074B5240130C
logging synchronous
login
modem InOut
speed 115200,,,,,,,,this has been added to the configuration as well
stopbits 1
flowcontrol hardware
Router2811#show line
Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 0 CTY - - - - - 0 0 0/0 -
* 1 1 AUX 115200/115200- inout - - - 0 0 10/0,,,,,before it was 9600
322 322 VTY - - - - - 0 0 0/0 -
323 323 VTY - - - - - 0 0 0/0 -
324 324 VTY - - - - - 0 0 0/0 -
325 325 VTY - - - - - 0 0 0/0 -
326 326 VTY - - - - - 0 0 0/0 -
Line(s) not in async mode -or- with no hardware support:
2-321
Now remotely I was able to access the router.
But when I tried to reduce the speed from 115200 to 56000 (modem speed), my modem got disconnected and then I reduced the speed to 9600, but same problem happened ( modem got disconnected ).
Modem got disconnected after I received these funny characters :
æ€æ€f€˜€æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†
æ†æ†æ†æ†æ†æ†æ††€†€æ€
æ€æ€f€˜€æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ
†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ††€†€æ€
æ€æ€f€˜€æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ†æ
†æ†æ††€†€æ€˜€€~ff€˜þf† ``f˜†€†€æ€˜€€€˜˜fxfž žæ†ø˜ffžfx €€€~˜

What I did is this :
I dropped the PC's speed from 115200 to 57600,and it worked without seeing funny characters.
I have not touch the speed on the router side, I left it as it is.
What be the case if I reduce the AUX's rooter speed ? When I tried to change it by doing this :
Router2811#config line 1
Router2811(config-line)#speed 56000
Failed to ,,,,,,I do not remember right now
Why it gave me failed error message !!!!!
Thanks

Similar Messages

  • I cleared a playlist on my iPhone 4 because I wanted to remove the songs from my phone's storage (I had previously downloaded them) because I wanted to clear storage space. I now want to access the playlist via iCloud and can't. Thoughts?

    I cleared a playlist on my iPhone 4 because I wanted to remove the songs from my phone's storage (I had previously downloaded them) because I wanted to clear storage space. I now want to access the playlist via iCloud and can't. In other words, I want it to sync with the playlist as it exists in iTunes Match. Thoughts?

    Export Photos and Videos from Camera Roll to your computer.
    Empty Camera Roll.
    Make a Folder/Album with all photos and videos you want to have in your iPhone and sync them through iTunes.
    This will free up space in your iPhone and your iCloud.
    The backup of Camera Roll in iCloud is only to restore your iPhone. You can't access them directly.

  • Remote Access to a Time Capsule and Attached HD with Secure Communications.

    I have a private network with a 500 GB Time Capsule at the center. I have a 1 TB USB external hard drive attached via the USB port on the back of the Time Capsule, and have perfect access to it as long as my Macbook Pro(2008) is on the network. My issue is I am away from home for multiple months at a time and would like to be able to access the Time Capsule and hard drive from a remote location via the internet without worrying about others being able to see my data. I have been able to use the Go>Connect to Server function in the finder with a password for the Time Capsule working to limit access. I am wondering how secure this is regarding the data as it passes over the network or if there are other ways i need to be encrypting the data. Thanks in advance.

    When you say noone is providing a solution.. we have no idea who the noone is??
    Did you read Tesserax document on remote access??
    https://discussions.apple.com/docs/DOC-3413
    Tesserax is definitely someone.. and he has done a very good job of giving you 3 alternatives.. all of which work at least for some people.
    If you have read that.. then please tell us what you have tried and what failed??
    The issue most people have is not actually access to the TC .. it is the fact that you do not have a public static IP address. If you really want simple access to the TC it is dead easy.. buy a static IP from your ISP. Then you never have problems. Just directly access it using AFP (which does mean you have to do it from a Mac). Or buy a VPN router and put the TC in bridge behind it.. you still need a public IP that is static to make this simple and workable.
    ISP deliberately use dynamic IP addresses to prevent you hosting servers.. The TC is a file server in this setup. They are trying to stop you doing this since part of requirements are you don't host servers on non-business accounts. 
    What we need to know if you run into trouble..
    The exact network layout in your home? How is the TC configured. It must be main router with public IP on the WAN interface for BTMM to work.
    Which method you are using.. please use Tesserax's numbered system?? His methods are pretty much in order of ease.. BTMM is the apple method to do it. Use this first and foremost.
    And what device are you trying to use to access it from remotely??
    You need to recognise here that Apple has made this easy for only one protocol.. AFP. No other protocol is fully supported other than by trickery.

  • How to remotely access Time Capsule using iCloud and firmware 7.6.1?

    I have just applied the new Time Capsule 7.6.1 firmware that supposedly enables remote access to the drive via iCloud. However, how precise would this work?
    I have read several other threads here and elsewhere but they either explain how to do this using MobileMe or DynDNS.
    How precisely does iCloud now translate my internal IP to an external one and where do I access my drive in OSX when on the road?

    Really pretty simple.  That's if you've got the Time Capsule and your Computer set up correctly.
    Time Capsule setup:
    1.    Open Airport Utility
    1a.  Open Time Capsule Base Station tab
    1b.  Put iCloud NAME in "Back to My Mac"
    1c.  Enter Password, then wait for activation (less than 1 minute normally)
    1d.  Open Time Capsule Disks tab
    1e.  Check mark "Enable file sharing"
    1f.   Check mark "Share disk over WAN"
    1h.  Password self explanitory
    Computer (Mac)
    1.   Open iCloud in System Preferences
    2.   Put a check mark on "Back to My Mac", wait for actication (less than 1 minute normally)
    Connecting to Time Capsule Disk from you HOME network or outside your home network ((INTERNET))
    In order to connect to Time Capsule Disk off your local (home) network you must have an internet connection, if you do then do this:
    1.  Open Finder
    2.  In Finder open Shared if collapsed and double click on your Time Capsule name.
    3.  Double click your Time Capsule, enter password (if you required).
    4.  Once connected to your Time Capsule double click on your Disk to mount it enter password (if your required).
    5.  Done,  remember the connection speed is dependent on your internet quality (broadband vs dial-up).

  • How to deploy a Desktop Access 2010 app via Azure and RemoteApp?

    I currently sell an Access 2010 app that uses the 2010 Access Runtime for deployment on desktop PCs. I very much would like to make it available over the internet on PC/Mac/iPad using the Azure RemoteApp, if possible. The Access app has a number of supporting
    files- it’s not just an Access accdb or accde file. For it to work correctly all the supporting files need to be in folders related to the main accde/accdb fie. Those files are a few other accde files, csv, pdf, and some folders.
    Each of my clients (a company) may have 1-15 simultaneous users. On the Desktop Access version, I have a Front End accde installed on each workstation and a single Back End accdb data file installed on a shared drive. Each FE workstation is linked to the
    single BE data file. I would need to replicate this somehow on an Azure VM (like perhaps have a designated folder for the BE data file that each user account’s FE is linked to?).
    I created an Azure VM (server 2012 R2) and installed the Access Desktop App on it. I can access that full VM with RDP (and see the whole desktop, not just my Access app). What I’m trying to figure out is a way to do this with RemoteApp- can RemoteApp use
    my Access 2010 app as an available ‘app’ or does the user need to see the whole VM desktop? 
    As well, in my Azure portal the ‘RemoteApp’ option is grayed out ‘pending approval’ so I can’t test it. 
    Any help figuring this out would be great. Thanks- 

    N8827N
    I ended up a great solution for this. I'm using 3 Windows Server 2012 R2 VMs to run it as a RemoteApp program. It's set up sort of like this:
    VM 1: RD Broker
    VM 2: Active Directory (where Users/Groups are created)
    VM 3: AppServer (where the Access app is actually located and run on- the VM2/Active Directory 'talks' to the AppServer to create/validate users but all the action happens on VM3).
    RemoteApp requires Windows Server 2012 so I don't think it'll work with Server 2008. The great thing about RemoteApp is it opens the Access 2010 Front End in a unique window, all on its own. The user doesn't need to see the Desktop of the server- they just
    see the Access Navigation Form(s). 
    In brief, on the VM3/AppServer I have a  unique folder for the backend Access data file and a User Account (created in the VM2 Active Directory) for each user with the frontend Access file in C/Users/Username/AppData.
    RemoteApp- when the user logs in via the RemoteApp app- points to that specific user profile's frontend Access db in that location and opens it in its own window on their host computer. And since each FE is linked to a common BE data file everyone uses the
    same data, just like in a regular LAN Server FE/BE setup. 
    It required some changes in the Access app to deal with it- uploading images and files, emailing straight from the app, etc but it was worth it. I also had to pay a development company to set up the 2012 R2 Servers, as I didn't know the details of how to
    do that myself. But I'm managing the setup, ongoing, and it's not so hard to do.
    So now my customers can run the Access app on a PC, Mac, or iPad pretty much anywhere. Excellent way to extend an Access application.. 

  • E1200 Router with poor signal and low speeds

    Hello, I just bought an E1200 router, which is downstairs and about 50 ft away from me. I have only about 60% signal strength, and my speed test when connected wirelessly is only 5mbit up,4mbit down. I plugged my computer into the router via ethernet and I get 30mbit up, and 5mbit down.
    Are there any settings you could suggest to improve this? I tried several channels already, none above 60% it seems.
    Thanks!

    first>> http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0a6881b90224439b92c8d8f19ca42e5d_21511.xml&pid=80&...
    second>> reset the router. there is a button at the bottom, press and hold it for 10 seconds then leave it for 2 minutes.
    third>> reinstall the router using the setup cd.

  • Can't Access Router Settings via 192.168.2.1

    I have recently changed modem/routers as my connection speed was increased recently and the old modem wasn't up to the task... The previous modem/router was preconfigured and I did nothing to it, however the new one requires settings be fixed by accessing it via a browser at 192.168.2.1
    When the technician came to check my line and set up the new modem, we encountered a strange situation. Despite being connected by Ethernet cable, my machine could not access the IP address reserved for the router.
    The reply is: "Safari can’t connect to the server.
    Safari can’t open the page “http://192.168.2.1/” because Safari can’t connect to the server “192.168.2.1”."
    We tried Firefox and the same happened.
    I have deactivated my firewall, rebooted, changed cables, restarted the router, got Safari to pretend to be Explorer, got the neighbor's dog to bark at it, everything except make a blood pact with the devil, and the two browsers on my machine think that 192.168.2.1 is an external address- which it isn't, and of course fails to connect.
    The technician used his laptop to configure the thing, so I can access the internet (obviously) but I must find out why I can't access the router/modem's settings, if only to find some logical reason for this illogical behavior.
    I've tried looking this issue up, and I get lots of bad wiring, wireless connection, windows proprietary shenanigans, but none that explain my situation.
    I'd appreciate it if someone could help me make sense of this.
    My setup:
    Computer Model Name: Power Mac G4 (AGP graphics)
    Model Identifier: PowerMac3,1
    Processor Name: PowerPC G4 (3.3)
    Processor Speed: 1.35 GHz
    Number Of CPUs: 1
    L2 Cache (per CPU): 256 KB
    L3 Cache (per CPU): 2 MB
    Memory: 832 MB
    Bus Speed: 100 MHz
    Boot ROM Version: 4.2.8f1
    Sales Order Number: M7827LL/A
    Router: "2-Wire Gateway"

    Your advice did the job quite nicely and it seems this is the "natural way of things," but I was totally unaware of it since my previous modems were preconfigured and I never had to muck about with subnets and such things.
    What irks me is that this is basic, bare bones information that the Tech support people should have given me right off the bat. Why do they assume I have all the right numbers input into the Ethernet or PPPoE settings? They seemed totally perplexed that I couldn't connect, and frankly so was I- since my old Mac, as decrepit as it is, is still able to kick it with the modern way of things better than most computers I work with.
    If they had asked me if I had set the right IP's in the right slots, it could have been fixed in 2 minutes.
    Thank you very much for solving my problem, it saves me a lot of stress and confusion.

  • Trouble Accessing Router Setup via Browser

    I am having a strange issue with accessing my WRT54G router settings page via a browser. 
    Everytime I would type the IP address into the address box, I would get the message: cannot connect to server.  I used the link in the User Manual and got the same message. 
    Of all places, my son found a link on the Nintendo site and it worked.  I copied the link to my favorites in IE 7  and I can now access the setup page in the router.  I did the same thing with Mozilla and the link gives the aforementioned error.  The link is nothing more than the IP address.  Also, I might add that I took the router to work and could access the setup page from my office computer.  This seems to point to a browser issue. 
    Does anyone have a suggestion as to what I should do so that I can simply type the IP address? 

    Not very familiar with mozilla. But I'd recommend that you check if the proxy settings are on.
    The box said windows xp or better... So I installed Linux!

  • Cannot remotely access mac mini via Chicken of the VNC post recent updates

    Hi, updated my remote mac mini A running OS X 10.4 with QuickTime 7.5 for Tiger and AirPort Utility 5.3.2 Tiger yesterday. I can connect from my mac mini B via ssh into the mac mini A, but for some reason Chicken of the VNC will not work (it was working prior to the updates). I get the following message "channel 3: open failed: connect failed: Connection refused" in the command window when I try to get access to the computer via Chicken of the VNC and Chicken of the VNC itself tells me that the connection is refused.
    Any suggestions? How can I remove the AirPort Utility 5.3.2 Tiger which I assume is the culprit? Thanks
    (mac mini A is miles away, the only access I have is via the command window)

    Welcome to the forums, and thanks for the tip!

  • Remote access of InitialContext via JMX client

    Hi,
    I'm not sure if i'm the right place here for posting my problem, but I don't know where to put it otherwise.
    I'm trying to access a JBoss datasource via JMX. The JMX code and datasource code is both placed inside a WAR file that is deployed in Jboss 5.1.
    When I access the datasource from a servlet, it runs oke but when I try to run it from jconsole I get a classnotfoundexception.
    The code where I register the MBean is:
    MBeanServer mbs = ManagementFactory.getPlatformMBeanServer();
    try
    ObjectName mbeanName = new ObjectName(OBJECT_NAME);
    Test mbean = new Test();
    mbs.registerMBean(mbean, mbeanName);
    catch (Exception e)
    //handle
    The code where I get the exception is:
    Context initContext = new InitialContext(jndiProps);
    The exception is:
    javax.naming.NoInitialContextException: Cannot instantiate class: org.jnp.interfaces.NamingContextFactory [Root exception is java.lang.ClassNotFoundException: org.jnp.interfaces.NamingContextFactory]
    These are my JNDI props:
    java.naming.factory.initial=org.jnp.interfaces.NamingContextFactory
    java.naming.factory.url.pkgs=org.jboss.naming:org.jnp.interfaces
    java.naming.provider.url=jnp://localhost:1099
    Any ideas?

    OK - I found another thread dealing with the problem at hand.
    http://forums.sun.com/thread.jspa?threadID=5369697
    Edited by: Christian.Yttesen on Jan 13, 2010 5:15 AM

  • Server used to be listed on Remote Access web page before installing and configuring RemoteApp. Now it's gone.

    I am new to RemoteApp. I have been using WSE 2012 R2 for some time, mainly for the remote web access web site.  I would log into my site (<my name>.remotewebaccess.com/Remote).  Then, I would see my server listed under "DEVICES". 
    I would click on the tile for the server, and the Dashboard would open.
    I just followed a tutotial to install the role for RemoteApp publishing.  It looks like it worked.  I now go to my RD Web App site  (<my name>.remotewebaccess.com/RDWeb), and I can log in and see my RemoteApp.  But now I cannot
    figure out how to get to my server's Dashboard, because when I go to my main web acess site (that ends with "/Remote"), the server is not listed under devices.
    Ideally, I would like to see all of my computers, including the server, on the main Remote Web Access site.  Also, it would be great if I could see my RemoteApps there too.  But I don't know if that is possible.  Can anyone help me get
    to that state, or know if what I want is possible?  I want everything on the same web page:
    Devices
    Shared Folders
    Links
    RemoteApps

    Hi,
    Based on your description, I understand that DEVICES tab disappears from Remote Web Access website after RemoteApp
    configured. If anything I misunderstand, please don’t hesitate to let me know.
    à
    But now I cannot figure out how to get to my server's Dashboard, because when I go to my main web acess site (that ends with "/Remote"), the server is not listed
    under devices.
    Did all users encounter the same issue when access RWA? Please open Dashboard and navigate to USERS tab, then
    click the problematic user account and select View the account properties. In Properties of this user account, please navigate to Anywhere Access, then please check if Computer option was checked in
    Show selected links on Remote Web Access. Meanwhile, please also use an administrator user account to check if this issue still exists.
    In addition, please follow the path: C:\ProgramData\Microsoft\Windows Server\Logs\WebApps folder and check
    RemoteAccess log file if find more clues.
    Hope this helps.
    Best regards,
    Justin Gu

  • How to access a file via Applet and JavaScript

    I want to copy one file on the client machine from one place to another place from a Java Bean.
    To do this I created an applet and a Java Bean as follows:
    import java.applet.*;
    public class FileUtils extends Applet {
        public void copyFile(String src, String dest)  {
        private String source, destination; // setters/getters are there of course
        public void copyFile(ActionEvent actionEvent) { // Bean
            FacesContext fctx = FacesContext.getCurrentInstance();
            ExtendedRenderKitService erks = Service.getRenderKitService(fctx, ExtendedRenderKitService.class);
            String command = "var s = '"+ source +"'; var d ='" + destination +"'; " +  " document.fileUtilsApplet.copyFile(s, d); ";
            erks.addScript(fctx, command);
        }Then I added the APPLET tag referencing the above class in the page fragment:
                    <f:verbatim>
                        <applet code="FileUtils.class" name="fileUtilsApplet" height="30"
                                archive="/context-root/Applet.jar"
                                width="200">
                        </applet>
                    </f:verbatim>From the Java console I can see the jar is successfully downloaded, but when the code in the bean is executed, the JavaScript code does not seem to do anything, as if the "copyFile" public method was not called at all and no output in the Java Console as well.
    Note that I already followed the guidelines at http://www.oracle.com/technetwork/developer-tools/adf/learnmore/71-adf-to-applet-communication-307672.pdf .
    Do you have any ideas?

    Ok, I can see the permission problem now:
    java.security.AccessControlException: access denied (java.io.FilePermission c:\myfile.txt read)
         at java.security.AccessControlContext.checkPermission(Unknown Source)
         at java.security.AccessController.checkPermission(Unknown Source)
         at java.lang.SecurityManager.checkPermission(Unknown Source)
         at java.lang.SecurityManager.checkRead(Unknown Source)
         at java.io.FileInputStream.<init>(Unknown Source)
    Edited by: user10047839 on 1-feb-2013 7.29
    signing the Jar and downloading the certificate permanently does not change anything in Firefox. The Java console keeps giving the above exception.
    Any idea?

  • I cannot access my contacts via whatsapp and all of my whatsapp contacts for deleted after I updated my software to iOS 6. Help?

    I updated my software to iOS6 yesterday and now for some reason I have lost all of my whatsapp contacts and my whatsapp cannot access my contacts  can someone please help me ASAP? It is a bit urgent

    try going to SETTINGS > PRIVACY > CONTACTS > WHATSAPP
    if found OFF - Turn it ON
    hope it helps

  • Catalyst Instant Access: EtherChannel distributed via parent and client?

    Hello,
    can we build a EtherChannel that has some ports on the parent switch (C6807XL-) and some on the client (C6800IA-48TD)?
    Is that scenario supported now and if not will it be supported in the future?
    Thanks in advance and kind regards
    Matthias

    Not according to the configuration guide:
    http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/15-1SY/config_guide/sup2T/15_1_sy_swcg_2T/instant_access.pdf
    From page 2:
    IA client ports do not support these features:
    * Configuring EtherChannels with combination of FEX Ports from different FEX-IDs or
    combination of FEX ports with IA parent switch linecard ports is not supported.
    * FEX host port EtherChannel load balancing is not supported.

  • I can't access or send email through Thunderbird any longer (over a month) though I have checked settings and can access/send email via webmail and other device

    My cable provider changed (buy out or something) about a year ago but left my email address alone.
    Confirmed with the current carrier that my incoming/outgoing settings are correct and my email address doesn't need to be migrated.
    When I click "Get Mail," nothing happens: no error message. It has been like this for a month.
    I can check webmail, but it doesn't have my older emails or folders. I would love to get back on and spit everything out of Thunderbird. I did an internet search (including this forum) but haven't found anything useful.
    Thanks for any help.

    https://support.mozilla.org/en-US/kb/problems-sending-and-receiving-messages

Maybe you are looking for

  • Custom header name does not show in ALV...

    Hello Experts, I am using custom column names for my ALV display but when I display it does not show the title I specified. For example, one of my columns which is 'AMOUNT' has a custom name which is 'YTD AMOUNT'. But how come it still shows 'AMOUNT'

  • Query from Distributed Cache

    Hi I am newbie to Oracle Coherence and trying to get a hands on experience by running a example (coherence-example-distributedload.zip) (Coherence GE 3.6.1). I am running two instances of server . After this I ran "load.cmd" to distribute data across

  • Trading Partner information lost in Order Settlement

    Hi FICO Experts, Original documents are posted to Order with Trading Partner.  During the Settlement of Order costs from order to Cost Center, the Trading Partner information is lost in the settlement posting. Can anyone please tell me is there any w

  • Events in internal tables

    what are the events in internal tables...

  • Eyedropper picked up RGB. How to flag this?

    I'm running ID CS4 and working on a print design. I was recently using a consistent grey color on a design (C-0 M-0 Y-0 K-79). At some point I inadvertantly placed a PSD in to the design that used an RGB colorspace, in Photoshop I had colored the bac