Replace a PRAM battery in a PowerBook TI

Here's my Powerbook:
Machine Name: PowerBook G4
Machine Model: PowerBook3,2
CPU Type: PowerPC G4 (11.3)
Number Of CPUs: 1
CPU Speed: 400 MHz
L2 Cache (per CPU): 1 MB
Memory: 512 MB
Bus Speed: 100 MHz
Boot ROM Version: 4.1.8f5
Serial Number: QT1251JML98
Sales Order Number: M7952LL/A
Where's the PRAM battery in this PB? I see everything here BUT the PRAM bat.
http://www.ifixit.com/Guide/Device/PowerBookG4_TitaniumMercury
Which Guide gets me closest to the battery? Thanks

Hi Steve,
Check out the repair guide here at macsales.com.

Similar Messages

  • How to replace an PRAM battery??  IMac g3 9.1 "Bondi Blue"

    I think that my PRAM battery is dead. Can anyone give me instructions to replace it? I have a full working battery from an older computer lying around somewhere...

    Hi, Ben -
    Replacing the battery in early iMacs can be tricky. You would probably get a quicker directed response if you reposted this question in one of the hardware forums for the iMac G3 models. The most appropriate would probably be this one, the Using your iMac G3 (CRT) forum -
    http://discussions.apple.com/forum.jspa?forumID=888
    Not all computers use the same battery. This Apple KBase article cross references battery part numbers with models -
    http://support.apple.com/kb/TA21569

  • PRAM Battery for Powerbook G4 17" 1.33 problem

    I have an Aluminum Powerbook G4 17" 1.33 GHz computer and need to replace the PRAM battery. This poses a problem. Typically they sell the PRAM battery/USB board as one replacement because the two rechargeable 3.7 v coin CGL 2430 batteries are spot welded & soldered to the USB board in parallel. The replacement part is 922-6064. When I look for a replacement, all I can find are used parts which mean that the batteries have a diminished life. Panasonic stopped making those batteries in 2005 and I can't find anything comparable. Even the places that advertise new parts say they only have used in the end. Next model up, the 1.5 GHz Apple made a battery pack that can be replaced. NewerTech makes that replacement. I would like to replace the batteries on my present USB board - new ones can be soldered or a plug can be added, but I have run into these problems. Those coin batteries are not available and I know the voltage, but not the amperage of those coin batteries that were used. NewerTech can't tell me the voltage/amperage of their battery pack for the newer version Powerbooks, so I don't know if jury-rigging one of those packs would work with my version of the Powerbook. I can't find Apple's specs anywhere for the voltage/amps that should go into the PRAM/USB boards in the 1.33 model and the 1.5GHz model so that I can figure how to do this repair modification. The USB boards for both models look the same, but I don't think that they are, but what is the difference? Anyone have an idea how I can do this modification to add PRAM power to my USB board?

    Actually, this is a very minor problem, if the negligible incidence of posts here about replacement PRAM batteries dying is any indication. Apparently there are very, very few users of Powerbooks (going all the way back to the G3s of 1998-2001) whose use of these machines has outlasted a second PRAM battery. I still have a working 2003 Titanium Powerbook with its original PRAM battery in place, a working 1998 Powerbook G3 with its original PRAM battery in place, and a working 1997 Powerbook 1400C with its original PRAM battery in place. I doubt that new replacements are available for any of those batteries, but I wouldn't hesitate to buy used ones if I intended to use any of those computers for several more years. I suggest you go ahead and do the same, and install the used battery yourself to keep the cost down.
    Message was edited by: eww

  • How to replace PRAM battery in Power Mac 9600?

    Greetings. Need to replace the PRAM battery in a Power Mac 9600. Purchased a new battery, but can anyone tell me exactly how to remove the old one? Don't want to break the black plastic "cradle" it sits in. Thanks very much.

    You need to remove the cover/retainer that snaps over the top of the battery holder. Using a very small screwdriver, insert its flat tip between the outside of the socket's positive metal contact and the battery retainer's end. Gently pry outward against the plastic retainer to unsnap it. You may need to do the same at the opposite end to completely pop it off. Once that's removed, you can actually grasp the battery by its sides and roll it up and out of the holder. Otherwise, insert the same small screwdriver under the lip on the outer rim of the battery's positive end, and pry/lift it out of the holder.

  • Pram Battery replacement?

    I have been searching the apple support pages for the correct procedure to replace the Pram battery. Everything is working well on my G4 so this procedure is preventative.
    Can I swap the battery and start the computer up or do I have to press the pram button? Perhaps i have to hold down some magic combination of keys or at start up?
    Thanks very much

    Some references for you:
    [Texas Mac Man's PRAM, battery, PMU tutorial|http://www.geocities.com/texas_macman/pram.html]
    [PRAM reset directions|http://docs.info.apple.com/article.html?artnum=2238]
    You don't need to reset the PRAM if swapping the battery, though if you leave the computer without a battery for longer than about 30 seconds (or is that minutes?), it will lose the PRAM memory and will be as if you had reset the PRAM.

  • Replaced PRAM battery, now G$ Quicksilver won't power up

    I replaced the pram battery. Now my G4 Quicksilver will not power up. The light is on in front of the computer, as well as on the front of the monitor. However, pressing, pressing and holding for many seconds does nothing. No sounds--nada.
    I bought an iMac, and want to use the G4 in target mode to transfer files, and then set up a wireless network. I have no clue as to where to start, since the computer is dead with its lights on.

    Did you click on the blue text above?
    Here it is again:
    http://docs.info.apple.com/article.html?artnum=86760
    Click the above blue text.
    As you read the article that opened, towards the bottom, click "For Power Mac G4" to see model specific pictures.

  • Intel iMac PRAM battery replacement

    Can anyone point me at some instructions for replacing the PRAM battery in an early intel iMac please?

    It is a coin battery, 3 V Lithium (922-6476), and requires opening the case to get to it. I cannot find a teardown photo sequence that shows how to replace it. Nor do I find the battery pointed out in any of the tears downs available at ifixit.com.
    http://www.ifixit.com/Guide/Device/iMacIntel17%22
    Dah•veed

  • PRAM battery or no PRAM battery?

    I can't seem to find a reliable answer on the Internet, even from companies that sell PRAM batteries.
    I have a 15" MBP purchased in August, 2010. Model A1286, 2.66 GHz Intel Core i7, SDD, 8GB RAM.
    Does it have a PRAM battery or not? If so, what's it's expected life?

    OMG,
    If you're talking about the PRAM battery in the Beige G3 and not the PowerBook, there are few, if any, tests that say "dead" or "alive" with certainty. The Beige is, in my experience, the most finicky computer when it comes to weak PRAM batteries. I've taken batteries out of my Beige that were starting to give start-up problems, dropped then in older Macs where they worked flawlessly for several more years.
    Older Apple tech docs show using a multi-meter to test the battery while in the computer. Other people say to test it out of the computer. The later has the battery under zero load, so I question the results. Typically, the threshold low voltage level is said to be 3.1 to 3.2V. I've tested batteries reading 3.2V (in my hand--no load) that would not allow my Beige to start properly.
    Management is often better than testing. If you get a used computer, replace the PRAM battery before doing anything else. Once you have a computer running, leave it on wall power at all times; this keeps the battery out of play so it's not losing charge. If you have to remove the computer from wall power for more than a few hours, remove the battery and tape it to the case.
    If you do those things, the battery will not be a problem to routine operation. Even then, I avoid leaving a battery installed for more than three years.
    I got my Beige in mid 1999, and it's on the third battery. The first failed prematurely because i was unplugging the computer before going on vacation or extended business trips. The second lasted longer. I replaced it in late 2004 as a routine precaution while doing some other work on the Beige.

  • MacBook won't start. PRAM battery?

    So with a good power cable and full battery (used battery from another MacBook but didn't help) my MacBook wont power up. No fan, hard drive, white front light, or anything. I've had the computer for about 5 years, and it stopped working out of the blue. Should I replace my PRAM battery?

    So with a good power cable and full battery (used battery from another MacBook but didn't help) my MacBook wont power up. No fan, hard drive, white front light, or anything. I've had the computer for about 5 years, and it stopped working out of the blue. Should I replace my PRAM battery?

  • Does a 12" PowerBook have a PRAM battery on the logic board?

    We got an 867MHz 12" Aluminum PowerBook in today that doesn't seem to want to hold PRAM values any longer than 5 minutes. It doesn't seem to matter if it's plugged in and using the AC adapter as the source or the battery (as long as it's charged, of course ).
    I've gone through the typical battery of tests, like removing the Airport, add-on RAM, etc. but the problems persist. To get the item to boot, I've been repeatedly resetting the PMU (shift-option-command + power button) followed by a PRAM reset (option-command-P-R + power button) and eventually it will chime and start to boot. I suspect that I can end up isolating this to a specific set of steps. One of the oddities I've noticed is that when doing this, the power isn't actually off. For example, if I do the PRAM reset, the item will appear to be dead, but if I hit the caps lock key it's clear that the power is still on.
    Once the item boots, I can power it on and off, and it will reboot, as long as I don't let it sit any more than 5 minutes. If I let it sit 5 minutes or more, then I need to go through this whole reset game again.
    I've seen stuff like this happen on PCs that often have ROM/PROM batteries installed (sometimes removable, sometimes soldered to the board) that retain system settings. There seems to be something that looks like one of these batteries installed on this motherboard, but none of Apple's tech repair manuals reference replacing it, and it almost looks like its welded to a connector, but then again I'm not sure it's even a battery.
    So the question is: Does this motherboard have a PRAM battery on it that's failing? If there is one, is there a replacement or replacement kit available, or am I barking up the wrong tree all together?
    Thanks in advance.

    From what I can tell, this device uses a "mega capacitor" to maintain the charge on the memory. It looks almost like a battery that I put into one of my old cameras. This capacitor sits between the trackpad and the optical drive. The owner of this system did a DVD upgrade himself and it appears in the process he actually knocked this capacitor off it's base on the mother board. It superficially APPEARS to be connected because there's a bar on the top end of the capacitor soldered to the motherboard that's holding it in place, but the bottom end broke off the motherboard.
    The boss of our company theorizes as follows:
    1. The PRAM and NVRAM has a high impedance, and when the mega capacitor is properly connected and without power, the discharge rate based on the RC time constant is very long (probably weeks...maybe months).
    2. When power is turned off it's the duty of this effective RC network to maintain PRAM and NVRAM since the discharge rate is so slow.
    3. With this capacitor busted off, the only capacitance that exists in the circuit is likely that of RF bypass capacitors and any other capacitors that may be used to filter out the supply. Since these are likely much, much lower in value the RC time constant becomes minutes instead of days/weeks/months.
    I think this is a good theory for the following reasons:
    1. If the unit sits, powered off, for any amount of time greater than 3-4 minutes and it's powered up, the unit comes on, but the CPU doesn't start processing. The optical media initializes, the caps lock key will light, and if you listen closely to the unit you can hear stuff running....but the CPU doesn't start. The conjecture is that the all PRAM/NVRAM parameters have been lost and when the CPU starts it sees nothing there and hence, does nothing. The unit is actually running, it just doesn't do anything.
    2. If the unit sits, powered off, for any amount of time greater than 3-4 minutes, the following process will allow it to start up:
    a. Turn the power on and leave it on for about 2-3 minutes. This is the dysfunctional state identified above, but what seems to be happening is that the effective RC network is being charged.
    b. After several minutes, turn the unit off and then immediately turn it on.
    c. The unit boots successfully.
    d. We can turn the unit off, and turn it on again, and it will successfully boot as long as we do it relatively quickly (within a minute or two), but if it's left off more than that then the "game" identified in steps a-c must be repeated.
    To me this implies the unit relies completely on the "mega-capacitor" to retain voltage on the PRAM/NVRAM. It sort of makes sense because the equivalent impedance of a battery is low compared to that of the RAM chips and it would have the effect of limiting the RC time constant needed for the unit to retain it's PRAM/NVRAM parameters for a very long period of time. That isn't to say the battery isn't supplying anything to the unit when power is off...it may very well be, but I suspect it simply isn't doing it to this circuit.
    Does this theory make sense?

  • PowerBook G4 PRAM battery

    A friend donated his retired 17" 1Ghz PowerBook G4 to my collection of older Macs. It worked when he took it out of service but it's been stored off power for several months. Does the PowerBook PRAM battery recharge like the ones in the original G3 Powerbooks or does it run down and die like the 3.6V 1/2AA PRAM batteries in desktop Macs? I've noticed they are quite expensive and not the easiest item to replace.
    I can't do any testing at the moment because he forgot to send the power adaptor and the main battery is DOA. Fortunately, he will post the adaptor tomorrow.
    Thanks in advance,
    Allan

    Thanks, BGreg.
    This is my fist PowerBook. Other than not keeping date and time, are there any specific problems associated with a dead PRAM battery in this model. I know it can wreak havoc in a Beige G3 and some of the pre-G3 models. I've replaced PRAM batteries in Wallstreets before and that helps with several problems, but the Wallstreet is Old World ROM.
    If I have a good main battery, have the computer plugged into wall power most of the time and is connected to our always-on home network, can I except reasonably normal function should the PRAM battery be truly shot?
    AJ

  • PB 5300c Pram Battery Replacement

    Several months ago I picked up a PowerBook 5300c in excellent, well taken care of condition. All works well with it but the pram battery is dead.
    Having it replaced would cost me more than what I paid for it. I don’t have much experience with the inside of PowerBooks, except putting Ram in my Pismo.
    Does anyone have experience replacing these on your own?
    Is it a major undertaking?
    Does anyone know of an internet site or source of information that may be able to help me if I decide to try this?
    Thanks
    greg

    Greg,
    You want the "PowerBook1905300.pdf" take-apart manual here:
    http://www.whoopis.com/computer_repair/
    You can save the file to your HD with a control-click on the name and selecting the appropriate command.
    You might also enjoy reading the 5300 FAQ at this site:
    http://www.alksoft.com/5300_stuff.html

  • Replacing pram battery

    I will be opening up my iMac (G3 400 early 2001) soon to install a new hard drive. I realized this would be a good time to change the pram battery which is original, but still good.
    If I do the replacement quickly enough will all the settings be saved? If not, what is involved to restore them? Is resetting the pram necessary? What, in general, should I know about doing this?
    Also, since this will, at the same time, involve replacing the HD for upgrade- I will be cloning bootable external to new HD (with partition just below 128GB- how will the battery change complicate, if at all, this procedure? If settings are lost should I restore them when booted first from the external before cloning and partitioning? Thanks for any help on this.

    You are stressing too much about this. Just replace the battery. After you get everything reassembled you will want to reset the PRAM and then set the clock.
    It has nothing to do with the hard drive.

  • Replace PRAM battery in in Intel core2 duo iMac?

    I have just installed the iStat widget in my Intel Core2 Duo 2.16 Ghz iMac. I was a little surprised to see a battery level reading on it (of 45%). I wonder if it is measuring the remaining life of the PRAM battery. Remembering how badly my Powermac and my wife's G5 iMac behaved when their back-up batteries needed replacing, I want to avoid the same situation on my Intel iMac. However I can find nothing on Apple support for replacing the PRAM/back-up battery on an Intel iMac, so I am wondering if there is a replaceable battery or not. Anyone know?
    Thanks
    Wilson

    From iSlayer Battery Section:
    This section shows various information about your Mac’s battery. This section is only visible if you actually have a battery and won’t appear on desktops.
    Percentage
    The current battery charge as a percentage. This is also shown as a bar at the bottom of the section.
    Time
    Time left using the battery, time until charged, or “Charged” if the battery is fully charged.
    Source
    “AC” if the Mac is connected to mains power, or “Battery” if the battery is being used.
    Status
    This shows if the battery is charged, charging or draining.
    Battery Health
    This is a comparison between your current battery capacity and capacity of it when it was new. For example, if your battery lasted 5 hours when it was new, a figure of 50% suggests you should get 2.5 hours out of your battery now.
    Cycles
    The amount of battery “cycles” the battery has had. One cycle is defined as a complete discharge and charge of the battery, but partial discharge and charges also count. So, two half discharge and charges are the same as one complete discharge.
    For some tips on how to get the most out of your laptop’s battery, please visit this Apple support page.
    Message was edited by: lakewoodlawnman

  • PRAM battery reset or similar for PowerBook G3 400MHz Lombard

    Hello,
    I recently acquired a PowerBook G3 400MHz Lombard? (not pismo)- with the battery dead and it not getting any signs of life beyond a green light on the display or the caps-lock. I was wondering if there is a simple fix that might get this going, similar to removing the PRAM battery on a Pismo that has been sitting there til the batteries drained. Any help would be appreciated so I'm headed in the right direction on this.
    Thanks.
    -m

    Hi jpl,
    First let me say a big thank you for such a prompt response. I love this place because of participants like you... thanks.
    You have a Powerbook G4 in your profile; if you do
    not have the Powerbook G3 Series Bronze Keyboard, the
    following does not apply. If you have a G4, head over
    to this forum:
    http://discussions.apple.com/category.jspa?categoryID=
    124
    Sorry for any confusion. I indeed have a G3 Lombard with the bronze keyboard (Got it in 1999). I then upgraded to the G4 about 3.5 years ago. And just last week I got me a shiny new intel iMac.
    The Lombard is currently running Jaguar, but its gotten sluggish and has run out of space (original specs). I want to reinstall OS 9, but I have this current issue with starting it up.
    Generally, if the powerbook does boot up, even
    occasionally, you do not have a corrupted power
    manager. The procedure you quote is for a powerbook
    that does not start at all, even after a normal power
    manager reset, and this usually occurs when a 'book
    has been unused for a few months...this allows the
    batteries to run flat and corrupt the power manager.
    Unlike desktop computers, powerbooks can run fine
    with a dead backup battery.
    The computer is being used almost daily...
    I would look first at other potential problems...
    - Do you have a working main battery?
    No.
    - Once the 'book is running, does it perform
    normally? Can you sleep/wake the 'book and also
    perform a restart?
    Once it's running it performs normally. I can sleep and wake. I CANNOT perform a restart.
    - Once running, open the System Profiler >
    Memory...does it report either 512K or 1MB of L2
    cache?
    My 'book is at home currently... I will check when I get home.
    - When shut down, remove the main battery and optical
    drive. With the power adapter connected, press the
    reset button on the back panel to reset the power
    manager, wait 5 seconds, then press the power button.
    Does it •always• start normally from a cold start
    when following this procedure?
    I want to say no, but I will double check this as well when I get home.
    Thanks again for your help!

Maybe you are looking for