Right firmware for WRT54G version 2

Hi,
I need to reflash a WRT54G version 2, but on the support page I can not find any firmware. Only for version 2.2. is it the compatible also with version 2?

Leonardo you can visit http://homesupport.cisco.com/en-apac/support/routers/WRT54G then go to Downloads you will be able to see the Version 2 from the drop down.
Thanks!

Similar Messages

  • Newest firmware for WRT54G version 5.1??

    I am a newbee, so please help.
    When I download the firmware from this site it says the newest is 1.01.1??
    But when I want to forward a port it says firmware prior to 1.32 won't work.
    What new firmwire do I need and where can I download it?
    By the way, will it also work on a WRT54G version 5.0??
    Best regards Xaykev

    hi , the firmware version 1.01.1 , will work with both the wrt54g v5 and the wrt54g v5.1
    try this and then go ahead with the port forwarding.

  • Trying to upgrade firmware for WRT54G V6 on Windows 7

    Since buying a windows 7 PC, my WRT54G V6 is dropping connection a lot more than it should (1/hr).  Because of this i thought to update the firmware.  I have downloaded the new .bin and accessed 192.168.1.1, but when i try to move to the ADMINISTRATION page all i get is ascii chars and no admin page, the only pages that actually work are the basic setup and DDNS setup.  For info i'm currently running Firmware Version: v1.00.9
    Asked for help online and got as far as downloading Tftp,0, but that onlyworks to the point where it tells me ''unable to get responses from the servers''
    can anyone help or do i just get a new router ???
    Thanks in advance, les
    Solved!
    Go to Solution.

    Try to upgrade the router's firmware using TFTP utility..Download the TFTP utility and save it on the desktop.Also Download the firmware for WRT54G v6 and save it on the desktop.
    Follow these steps to upgrade the firmware on the device : -
    Double click the TFTP.exe file and click run.
    For Server- Enter the IP Address of the router that you assigned.  By default, the router is 192.168.1.1...
    For Password- Enter the password you assigned the router. By default, the router’s password is “admin”.
    For File- Click the triple “…” button and browse for the .bin firmware file...
    Click Upgrade button to start upgrading.  A progress bar should show up to show the progress.
    Once the Upgrade is done press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
    **Make sure your modem is connected to the router on internet port and the computer on the ethernet port of the router while you run the TFTP program.

  • No downloadable firmware for my version.

    Today, I decided that, since my WRT54G v7 router is getting notably old, I should update the firmware. After taking some time to read the documentation, I went to download the firmware.
    Or well, at least I tried. There is no Version 7 firmware.
    Can someone please tell me why there is no way to upgrade for me (I tried v8, but obviously, that doesn't work..)? Is there any other way to upgrade?
    Thank you.

    To download the firmware for your router click Here. This firmware is for WRT54G version 7.

  • Why there is no option for WRT54G Version 7??? the versin...

    Why there is no option for WRT54G Version 7??? the versin no. jump from 6 to 8??Which firm ware should  I download?

    For US no vesrion 7 is released. Might be in other countries.

  • After updating my iphone 5s to 7.1 ... the keyboard is crashing and it takes too long to respond, what is the solution? if there any link from which we can download the original 7.1 firmware for A1533 Version?

    After updating my iphone 5s to 7.1 ... the keyboard is crashing and it takes too long to respond, what is the solution? if there any link from which we can download the original 7.1 firmware for A1533 Version?

    Restoring the iPhone will reload its firmware.
    Plug the iPhone into (the current version of) iTunes on your computer.
    Let it sync.  Then choose "Restore" from the iPhone's summary page in iTunes.

  • Can't Find Firmware for WRT54G V5.1

    Purchased the WRT54G week ago, looked for latest firmware (just wanted to have the latest one). Looked on linksys, couldn't find the firmware for version 5.1 (i saw the version of the router on the sticker on the bottom underneath the Linksys logo, it says model no: WRT54G V 5.1). Do i have to use another firmware type instead of searching for the 5.1 ?

    the version 5 firmware will work with the version 5.1

  • Can NOT download v4.21.1 Firmware for WRT54G v4

    There is something wrong with the Linksys download site.
    Can someone confirm this by trying to download that specific firmware?
    http://www.linksys.com/servlet/Satellite?c=L_Content_C1&childpagename=US%2FLayout&cid=1115416835852&...
    When trying to download the latest firmware for my WRT54G v4, I get nothing but an empty .zip folder (0 bytes).
    I also get some sort of server error while attempting to download the "version info".
    I have tried three different browsers to be sure.
    Hmmm....I just successfully 'test' downloaded other firmware versions, so I know it's got to be the link for this particular firmware I need.
    When will this be fixed?
    Or, where else can I get Linksys v 4.21.1 firmware for my WRT54G v4?
    Thanks
    Message Edited by thenut on 02-06-200709:06 AM

    Download the firmware file for the WRT54Gv3. v3 and v4 are compatible. v5 and later use a different kernel. If you select v3 in the downloads you download the file "WRT54GV4.0_4.21.1_US_code.zip" which is the same filename you would get for the v4. I guess it is just a configuration error on the server which breaks the links for the v4...

  • New Firmware for WRT54G v5

    Guys,
    If you're still having problems with your v5 router, Linksys has just recently released the latest firmware which is version 1.00.9. You can download the file on the link given below.
    http://www.linksys.com/servlet/Satellite?c=L_Download_C2&childpagename=US%2FLayout&cid=1115417109974...
    Message Edited by RDL on 05-20-2006 05:07 PM

    I'm using version 1.02.8 but currently trying to hack the router to use DD-WRT or Open WRT for a project. Every time I try to upload the firmware the router says  "Bad Archive". I tried with via Ethernet and with a TFTP client but neither of them worked. Any suggestions or ideas?
    My router is a Linksys WRT54g v5.
    Thanks

  • New Firmware for WRT54G ver6 Posted

    Saw new firmware posted on the download page for wrt54g ver6 dated 7/2/07, the new version is 1.02.2  good luck people.

    I get "Bandwidth value is out of range 64--10000" when enabling QoS. When I set to Upstream Bandwidth to Manual, the problem goes away. But when I switch back to Auto, I am able to save the settings initially. But when I try again, the problem comes back.
    Wonder what's wrong... this is no issue with firmware 1.00.9.

  • Firmware for WRT54GS

    I am using a WRT54GS, the firmware ids v3.37.7. Isn't it a bit too low base on the discussion in the forum. 
    Jonathan

    I have a linksys WRT54GS version 1 and currently is loaded with firmware 2.07.1. Do you where I can get the latest firmware for this model?
    The firmware is not available on the linksys for download.

  • Firmware for WRT54G ver. 7

    I am not sure that is it my computer have a problem but i could not find the firmware for version 7 ... there is only firmware for 1,1.1,2,2.2,3,3.1,4,5,6,8 no 7 ...
    So anyone can kindly tell me where can i get the firmware for version 7 ?

    well...you need to go to www.linksys.com/uk ... the firmware for the wrt54g v7 should be in that list ..

  • Upgrade Firmware for WRT54GS V.6

    I am new to the wireless world and just purchased the WRT54GS V.6 router and it says I have downloads for this firmware. I have copied so many instructions I don't know where to start first. Can someone give me some advise as to what to do? Thanks for any information!!!

    Hi, you seem to know the way around the router, so I hope you help me. I downloaded  the new firmware for v6. and installed it. It call my attention the fact that the firmware started to load slowly, saying that it will restart, and about 40% it congratulate me for the work done, but no restart and after I restarted manually, no wireless!!! Any idea? from the first Easy Link I got a configuration on a pen flash drive, and everytime I restart, I use it, but it is not automatic like it used to be on my older router. Besides the fact that I have to have the computer wired to get it wireless, which is absurd. Thanks if you can help
    Alfredo

  • What's the latest firmware for WRT54G?

    For my Linksys WRT54G router, my current firmware is 4.21.1. 
    When I browse for new firmware (by choosing 4.0 on the drop down menu), it says that I have the latest one.  Is this true or am I searching for it wrongly?

    dudztgp wrote:
    Make sure to select the proper hardware version before the firmware. If your WRT54G is hardware version 4.0, then you have the latest firmware already installed.
    Underneath my router it says "Model No: WRT54G ver.2"
    And I upgraded my firmware a couple years ago and it is 4.21.1.
    Am I fully updated or no?

  • Latest Firmware for WRT54GS 5.1

    Hello
    I have a WRT54GS 5.1, when connecting to the router it states that the current firmware version is 1.52.2.
    I want to be able to use VPN client (Mac OS X VPN Tracker) with this router. I heard that some Linksys Routers (god knows why) mess up VPN connections. I was hopeing that a firmware upgrade would fix it.
    The latest version of firmware I can find on the site for the WRT54GS 5.1 is version 1.50, which seems to be older than what the current version of the router is.
    Any ideas on what to do?
    Cheers
    Jake

    You can use the firmware on the website ... also you can go to ftp.linksys.com/pub/network ..... to check the firmware of the wireless router .....
    Any firmware upgrade will not mess-up with VPN connection .... however you need to reset the router after upgrade .....

Maybe you are looking for

  • Error when creating a TO

    Hi Guys, When I am creating a transfer order based on an outbound delivery, I'm encountering this type of error: "You have not selected data for the material document 85XXXXXXXX." Do you guys have an idea how can I correct this issue?? Thanks!

  • Display the id of new Record in the browse page of BC4J Struts App

    I am working on an application using BC4J Struts with backbone on Oracle 8i.I am using DBSequence Type for my Employee ID.Since I am using this Id as search criteria for employee, I want to show Employee Id after insertion of new Employee.How can I d

  • Reporting on a MS Access Database

    Hello All, Here is what we want to achieve. Business in the short run wants to do their reporting on a MS Access Database. This Access database sits on a shared secure Windows network drive. Our server is a Solaris box. Will ODBC work fine? Also how

  • How to attach a search help in a table control coloumn based on the search

    Hi, Can anyone help me for attaching a search help in a table control coloumn based on the search help value of another coloumn in the same table control. Regards, Ratheesh BS

  • In which tables are the data for the aplication KSB1?

    I'm getting data from Qlik View with a BI tool called Qlik View. I need help to find in which tables are the data for KSB1 aplication. I've found something in COBK and COEP but there's more table involved since I didn't find all data. Somente can hel